Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Silicon on insulators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Early development of ceramic fiber insulation for the Space Shuttle

The evolution of reusable surface insulation is described, with attention to the mullite and other aluminosilicates, zirconia, and silicon carbide-coated carbon compositions experimented with in the late 1960s and early 1970s. Evaluation and development concentrated in this period on such aspects of design and material properties as cold soak performance, attachment, shock impingement, surface coating cracks, and tile gap design and heating. In addressing the central problem of heat-shield thermal conductivity, it was found that for a given density, silica fibers had a lower conductivity than those of mullite. This was due to the one-micron, as opposed to 4.7-micron, diameter of the silica fibers, which resulted in smaller pores and therefore less convective and radiative heat transfer. Attention is also given to tile coating materials and the high-temperature processes by which they were applied.

Buckley, J. D.↗
NASA NTRS1990

Electron beam induced damage in PECVD Si3N4 and SiO2 films on InP

Phosphorus rich plasma enhanced chemical vapor deposition (PECVD) of silicon nitride and silicon dioxide films on n-type indium phosphide (InP) substrates were exposed to electron beam irradiation in the 5 to 40 keV range for the purpose of characterizing the damage induced in the dielectic. The electron beam exposure was on the range of 10(exp -7) to 10(exp -3) C/sq cm. The damage to the devices was characterized by capacitance-voltage (C-V) measurements of the metal insulator semiconductor (MIS) capacitors. These results were compared to results obtained for radiation damage of thermal silicon dioxide on silicon (Si) MOS capacitors with similar exposures. The radiation induced damage in the PECVD silicon nitride films on InP was successfully annealed out in an hydrogen/nitrogen (H2/N2) ambient at 400 C for 15 min. The PECVD silicon dioxide films on InP had the least radiation damage, while the thermal silicon dioxide films on Si had the most radiation damage.

Pantic, Dragan M.↗
NASA NTRS1980

Developments in fibrous refractory composite insulation

The development of a new insulation material for heat-shielding advanced reusable entry vehicles is reported. The material, called fibrous refractory composite insulation, is a composite of two ceramic fibers with no additional additives to bond the fibers together; it also includes silicon carbide, an emmittance agent, to improve its optical properties at high temperature. One fiber is a drawn 11-micron-diameter aluminoborosilicate fiber, the other fiber is the silica fiber (microquartz) used in producing silica RSI (reusable surface insulation for the Space Shuttle), which is a blown fiber of 1-3 micron diameter and variable length. A composition containing 20%, with a thermal shock resistance of 1.8 that of all silica insulation, has been successfully produced in a pilot plant.

Leiser, D. B.↗
DOE OSTI2020

Comparative study on the overall energy performance between photovoltaic and Low-E insulated glass units

In this report a novel semi-transparent building integrated photovoltaic (BIPV) laminate was developed and introduced in this paper. It was produced by cutting standard mono-crystalline silicon solar cells into small strips and then making electrical connections between each strip before laminating the cells between two layers of glass. The overall energy performance and energy saving potential of the BIPV insulated glass unit (IGU) under real world conditions were identified through a side by side comparative study. Compared to the reference IGU, the BIPV IGU had lower solar heat gain coefficient (SHGC) but much higher U-factor. The average HVAC electricity saving of the BIPV IGU was about 10% relative to the reference IGU. Daylighting measurement and analysis were carried out to evaluate the trade-offs associated with the BIPV IGU between daylight, glare, and lighting energy use. The results indicated that the BIPV IGU is better than the reference IGU in reducing discomfort glare. However, if the most conservative viewpoint near the window is used for the assessment, a lower transmittance BIPV IGU is required to bring the overall discomfort levels below the perceptible level. Lastly, the net energy saving potential associated with the novel BIPV IGU was identified based on the power, thermal and daylighting performance. On average, the BIPV IGU saved 16.8% of the total electricity use of the room. Further studies and improvement on the energy conversion efficiency of solar cells, the optimal transmittance as well as the thermal properties would make this technology more energy-efficient and affordable.

14 SOLAR ENERGY↗
DOE OSTI2023

On the 3D printability of silicone-based adhesives via viscous paste extrusion

Silicone, a commonly used household and construction adhesive, filler, or sealant, is also known for its flexibility, thermal stability, and insulating properties. It is viable as a conformally 3D-printed elastomeric matrix for flexible electronics and biomedical applications. Since most of the popular 3D printing methods use precise print specifications and defined resolution, this study explored the 3D printability of commercial silicone adhesives via a paste extrusion setup. Its viscoelastic and composition properties including the dimensional accuracy and mechanical properties of printed objects using controlled print parameters have been investigated. Finally, these experimental processes in 3D printing should pave the way in using materials originally intended for household use.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Silicon crystal growth in vacuum

The most developed process for silicon crystal growth is the Czochralski (CZ) method which was in production for over two decades. In an effort to reduce cost of single crystal silicon for photovoltaic applications, a directional solidification technique, Heat Exchanger Method (HEM), was adapted. Materials used in HEM and CZ furnaces are quite similar (heaters, crucibles, insulation, etc.). To eliminate the cost of high purity argon, it was intended to use vacuum operation in HEM. Two of the major problems encountered in vacuum processing of silicon are crucible decomposition and silicon carbide formation in the melt.

Khattak, C. P.↗
DOE OSTI2021

Ferroelectric polarization retention with scaling of Hf 0.5 Zr 0.5 O 2 on silicon

In this paper, we investigate the polarization retention of Hf 0.5 Zr 0.5 O 2 (HZO)-based metal–ferroelectric–insulator–Si (MFIS) capacitors with scaling of the ferroelectric (FE) layer thickness from 5 nm to 20 nm. The capacitors have a constant interface layer capacitance of ~24 μF/cm 2 , developed due to the integration of HZO on a degenerated Si as a bottom conducting electrode. It is observed that 20 nm HZO films show a small change (~5%) in FE polarization (P FE ) between short (10 μs) and long (6 s) retention time, while 5-nm-thick films exhibit a large difference (~90%). Furthermore, the dependence of P FE retention loss on the FE thickness can be understood by the presence of a built-in electric field in the FE layer, generated due to charge continuity between the FE and the interface layers in the ground state without any external bias. A direct experimental observation also confirms that a residual voltage is developed at the node between the metal–ferroelectric–metal and metal–oxide–semiconductor capacitors connected in series, in the ground state with zero external bias. It is expected that a proper understanding of the built-in field developed in the FE layer in an MFIS stack is crucial for FE memory retention characteristics.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Characterization of Adhesives for Attaching Reusable Surface Insulation on Space Shuttle Vehicles

An extensive development and testing program on adhesive systems shows that: (1) A closed cell silicone rubber sponge bonded to substrates with thin bond lines of glass filled adhesive exhibits density and modulus values approximately one third that of solid silicone adhesives; (2) utilization of glass or phenolic microballoons as fillers in silicone adhesives reduces density but increases moduli of the vulcanized materials; (3) the silicone elastomer based adhesives appear to be complex systems rather than homogeneous, isotropic materials. Tensile, shear, and compression properties plotted versus temperature verify this conjecture; and (4) constant strain-stress relaxation tests on glass-filled adhesive show that stress relaxation is most pronounced near the glass transition temperature.

Owen, H. P.↗
NASA NTRS1991

Industrial Applications of Graphite Fluoride Fibers

Based on fluorination technology developed during 1934 to 1959, and the fiber technology developed during the 1970s, a new process was developed to produce graphite fluoride fibers. In the process, pitch based graphitized carbon fibers are at first intercalated and deintercalated several times by bromine and iodine, followed by several cycles of nitrogen heating and fluorination at 350 to 370 C. Electrical, mechanical, and thermal properties of this fiber depend on the fluorination process and the fluorine content of the graphite fluoride product. However, these properties are between those of graphite and those of PTFE (Teflon). Therefore, it is considered to be a semiplastic. The physical properties suggest that this new material may have many new and unexplored applications. For example, it can be a thermally conductive electrical insulator. Its coefficient of thermal expansion (CTE) can be adjusted to match that of silicon, and therefore, it can be a heat sinking printed circuit board which is CTE compatible with silicon. Using these fibers in printed circuit boards may provide improved electrical performance and reliability of the electronics on the board over existing designs. Also, since it releases fluorine at 300 C or higher, it can be used as a material to store fluorine and to conduct fluorination. This application may simplify the fluorination process and reduce the risk of handling fluorine.

Hung, Ching-Cheh↗
NASA NTRS1994

Plasma chamber testing of advanced photovoltaic solar array coupons

The solar array module plasma interactions experiment is a space shuttle experiment designed to investigate and quantify the high voltage plasma interactions. One of the objectives of the experiment is to test the performance of the Advanced Photovoltaic Solar Array (APSA). The material properties of array blanket are also studied as electric insulators for APSA arrays in high voltage conditions. Three twelve cell prototype coupons of silicon cells were constructed and tested in a space simulation chamber.

TRT-EXPERIMENTAL↗
DOE OSTI2022

Electric Drive Technologies Research: Bottom-Up Soft Magnetic Composites (FY2022 Annual Progress Report)

In order to meet 2025 goals for enhanced peak power (100 kW), specific power (50 kW/L), and reduced cost (3.3 $\$$/kW) in a motor that can operate at ≥ 20,000 rpm, improved soft magnetic materials must be developed. Better performing soft magnetic materials will also enable rare earth free electric motors. In fact, replacement of permanent magnets with soft magnetic materials was highlighted in the Electrical and Electronics Technical Team (EETT) Roadmap as a R&D pathway for meeting 2025 targets. Eddy current losses in conventional soft magnetic materials, such as silicon steel, begin to significantly impact motor efficiency as rotational speed increases. Soft magnetic composites (SMCs), which combine magnetic particles with an insulating matrix to boost electrical resistivity (ρ) and decrease eddy current losses, even at higher operating frequencies (or rotational speeds), are an attractive solution. Today, SMCs are being fabricated with values of ρ ranging between 10 -3 to 10 -1 μohm∙m, which is significantly higher than 3% silicon steel (~0.05 μohm∙m). The isotropic nature of SMCs is ideally suited for motors with 3D flux paths, such as axial flux motors. Additionally, the manufacturing cost of SMCs is low and they are highly amenable to advanced manufacturing and net-shaping into complex geometries, which further reduces manufacturing costs. There is still significant room for advancement in SMCs, and therefore additional improvements in electrical machine performance. For example, despite the inclusion of a non-magnetic insulating material, the electrical resistivities of SMCs are still far below that of soft ferrites (10 – 10 8 μohm∙m).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Heterogeneous Integration of Flipped Oxide Heterostructure Membranes for Nanoelectronics

Freestanding complex oxide membranes enable the release and transfer of epitaxial films, offering new design freedoms for next‐generation electronics. While the LaAlO 3 /SrTiO 3 (LAO/STO) heterostructure exhibits remarkable tunable conductivity at its interface, the active interface remains buried beneath the substrate, limiting access to this functionality. Here, we demonstrate how the LAO/STO heterostructure, in membrane form, can be flipped and precisely positioned on silicon and other platforms using polymer‐free micromanipulation. The transferred membranes preserve atomically smooth surfaces, high crystallinity, and key electronic properties. Through the 44‐nm insulating STO layer, ultra‐low‐voltage electron‐beam lithography (ULV‐EBL) writes conductive nanostructures at the now‐accessible STO/LAO interface, offering the potential to function as programmable local gates that modulate charge carriers in the underlying silicon. The platform establishes a general strategy for integrating complex oxide heterostructures with semiconductors, quantum materials, and flexible substrates, enabling new architectures for reprogrammable nanoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High‐Performance Zinc Tin Oxide TFTs with Active Layers Deposited by Atomic Layer Deposition

Abstract New deposition techniques for amorphous oxide semiconductors compatible with silicon back end of line manufacturing are needed for 3D monolithic integration of thin‐film electronics. Here, three atomic layer deposition (ALD) processes are compared for the fabrication of amorphous zinc tin oxide (ZTO) channels in bottom‐gate, top‐contact n‐channel transistors. As‐deposited ZTO films, made by ALD at 150–200 °C, exhibit semiconducting, enhancement‐mode behavior with electron mobility as high as 13 cm 2 V −1 s −1 , due to a low density of oxygen‐related defects. ZTO deposited at 200 °C using a hybrid thermal‐plasma ALD process with an optimal tin composition of 21%, post‐annealed at 400 °C, shows excellent performance with a record high mobility of 22.1 cm 2 V –1 s –1 and a subthreshold slope of 0.29 V dec –1 . Increasing the deposition temperature and performing post‐deposition anneals at 300–500 °C lead to an increased density of the X‐ray amorphous ZTO film, improving its electrical properties. By optimizing the ZTO active layer thickness and using a high‐ k gate insulator (ALD Al 2 O 3 ), the transistor switching voltage is lowered, enabling electrical compatibility with silicon integrated circuits. This work opens the possibility of monolithic integration of ALD ZTO‐based thin‐film electronics with silicon integrated circuits or onto large‐area flexible substrates.

Allemang, Christopher R.↗
NASA NTRS1986

Minority-carrier mobility anomalies in low-resistivity silicon solar cells

Measurement of the minority-carrier mobility in the base region of a high-voltage metal-insulator-N-P solar cell (Green et al., 1984), as well as in other 0.1-ohm cm cells, provides direct proof that the high voltages measured for that cell are due not only to improved emitter characteristics but to an improved base region as well. The base characteristics are shown to be quite sensitive to the effects of diffusion-induced lattice stress originating in the emitter. The implications of these findings for the fabrication of high-efficiency cells are discussed.

Weizer, V. G.↗
DOE OSTI2021

Bottom-Up Soft Magnetic Composites

In order to meet 2025 goals for enhanced peak power (100 kW), specific power (50 kW/L), and reduced cost (3.3 $/kW) in a motor that can operate at ≥ 20,000 rpm, improved soft magnetic materials must be developed. Better performing soft magnetic materials will also enable electric motors without rare earth elements. In fact, replacement of permanent magnets with soft magnetic materials was highlighted in the Electrical and Electronics Technical Team (EETT) Roadmap as a R&D pathway for meeting 2025 targets. Eddy current losses in conventional soft magnetic materials, such as silicon steel, begin to significantly impact motor efficiency as rotational speed is increased. Soft magnetic composites (SMCs), which combine magnetic particles with an insulating matrix to boost electrical resistivity (ρ) and decrease eddy current losses, even at higher operating frequencies (or rotational speeds), are an attractive solution. Today, SMCs are being fabricated with values of ρ ranging between 10 -3 to 10 -1 μohm∙m, which is significantly higher than 3% silicon steel (~0.5 μohm∙m). The isotropic nature of SMCs is ideally suited for motors with 3D flux paths, such as axial flux motors. Additionally, the manufacturing cost of SMCs is low and they are highly amenable to advanced manufacturing and net-shaping into complex geometries, which further reduces manufacturing costs. There is still significant room for advancement in SMCs, and therefore additional improvements in electrical machine performance. For example, despite the inclusion of a non-magnetic insulating material, the electrical resistivities of SMCs are still far below that of soft ferrites (10 – 10 8 μohm∙m).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Metal–insulator transition and low-density phases in a strongly-interacting two-dimensional electron system

Highlights: • Quantum phase transition observed in ultrahigh mobility SiGe/Si/SiGe quantum wells. • Metallic state observed in a strongly interacting spinless two-valley electron system. • Indication of band flattening at the Fermi level reported. • Transport evidence for a sliding two-dimensional quantum electron solid reported. We review recent experimental results on the metal–insulator transition and low-density phases in strongly-interacting, low-disordered silicon-based two-dimensional electron systems. Special attention is given to the metallic state in ultra-clean SiGe quantum wells and to the evidence for a flat band at the Fermi level and a quantum electron solid.

36 MATERIALS SCIENCE↗
NASA NTRS1986

High-Strength, Low-Shrinkage Ceramic Tiles

Addition of refractory fibers and whiskers to insulating tiles composed primarily of fibrous silica, such as those used on the skin of Space Shuttle orbiter, greatly improves properties. New composition suitable for lightweight, thermally-stable mirror blanks and as furnace and kiln insulation. Improved tiles made with current tile-fabrication processes. For given density, tiles containing silicon carbide and boron additives stronger in flexure than tiles made from silica alone. In addition, tiles with additives nearly immune to heat distortion, whereas pure-silica tiles shrink and become severely distorted.

Wheeler, W. H.↗
NASA NTRS1991

Performance analysis of advanced spacecraft TPS

Spacecraft entering a planetary atmosphere require a very sophisticated thermal protection system. The materials used must be tailored to each specific vehicle based on its planned mission profiles. Starting with the Space Shuttle, many types of ceramic insulation with various combinations of thermal properties have been developed by others. The development of two new materials is described: A Composite Flexible Blanket Insulation which has a significantly lower effective thermal conductivity than other ceramic blankets; and a Silicon Matrix Composite which has applications at high temperature locations such as wing leading edges. Also, a systematic study is described that considers the application of these materials for a proposed Personnel Launch System. The study shows how most of these available ceramic materials would perform during atmospheric entry of this vehicle. Other specific applications of these thermal protection materials are discussed.

Pitts, William C.↗