Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPECIAL RELATIVITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Clinical 6 MV X-Ray Facility Photo-Neutron/Fission Interrogations with TMFD Sensors

Detection of several targets (U, Be, D2O) of interest to national security has been achieved at Purdue University’s 6 MV (~104 R/h) X-Ray clinical linear accelerator (CLINAC), from photoneutron/fission induced neutron signatures using a Centrifugally Tensioned Metastable Fluid Detector (CTMFD). Traditional neutron detection schemes were saturated and ineffective under the intense (to ~104 R/h) photon environment; however, the CTMFD sensor technology was capable of measuring the relatively insignificant (~10-12x lower intensity) neutron field produced from 6 MeV-end point X-Ray beam interactions with the CLINAC components and surroundings. This is in stark contrast to published results based on conventional belief for immeasurable neutron dose in 6 MV CLINAC facilities. Photoneutron and photofission neutron production rates were detected and analyzed at various standoffs from the isocenter, with and without special nuclear material (SNM) related targets ranging in mass from 5 g of Be, to ~0.6 kg of UO2. It was confirmed that 6 MV X-Ray photons do result in measurable neutron dose above normal cosmic background. Additionally, in threshold mode, the CTMFD operating under a tensioned metastable pressure of -5bar, enabled conclusive rejection of background photoneutrons, while enabling the rapid detection of: Be, D2O, C and U targets within seconds to minutes while operating in and around 104 R/h photon fields.

Ozerov, Stepan↗

A Generalized Anisotropic Hardening Rule Based on the Mroz Multi-Yield-Surface Model for Pressure Insensitive and Sensitive Materials

In this paper, a generalized anisotropic hardening rule based on the Mroz multi-yield-surface model is derived. The evolution equation for the active yield surface is obtained by considering the continuous expansion of the active yield surface during the unloading/reloading process. The incremental constitutive relation based on the associated flow rule is then derived for a general yield function. As a special case, detailed incremental constitutive relations are derived for the Mises yield function. The closed-form solutions for one-dimensional stress-plastic strain curves are also derived and plotted for the Mises materials under cyclic loading conditions. The stress-plastic strain curves show closed hysteresis loops under uniaxial cyclic loading conditions and the Masing hypothesis is applicable. A user material subroutine based on the Mises yield function, the anisotropic hardening rule and the constitutive relations was then written and implemented into ABAQUS. Computations were conducted for a simple plane strain finite element model under uniaxial monotonic and cyclic loading conditions based on the anisotropic hardening rule and the isotropic and nonlinear kinematic hardening rules of ABAQUS. The results indicate that the plastic response of the material follows the intended input stress-strain data for the anisotropic hardening rule whereas the plastic response depends upon the input strain ranges of the stress-strain data for the nonlinear kinematic hardening rule.

cyclic hardening rule↗

Propagation of surface waves on a semi-bounded quantum magnetized collisional plasma

The propagation of surface waves on a semi-bounded quantum plasma in the presence of the external magnetic field and collisional effects is investigated by using quantum magnetohydrodynamics model. A general analytical expression for the dispersion relation of surface waves is obtained by considering the boundary conditions. It is shown that, in some special cases, the obtained dispersion relation reduces to the results reported in previous works. It is also indicated that the quantum, external magnetic field and collisional effects can facilitate the propagation of surface waves on a semi-bounded plasma. In addition, it is found that the growth rate of the surface wave instability is enhanced by increasing the collision frequency and plasmonic parameter.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ecophysiology of mesophotic reef‐building corals in Hawai‘i is influenced by symbiont–host associations, photoacclimatization, trophic plasticity, and adaptation

Abstract Mesophotic reef corals remain largely unexplored in terms of the genetic adaptations and physiological mechanisms to acquire, allocate, and use energy for survival and reproduction. In the Hawaiian Archipelago, the Leptoseris species complex form the most spatially extensive mesophotic coral ecosystem known and provide habitat for a unique community. To study how the ecophysiology of Leptoseris species relates to symbiont–host specialization and understand the mechanisms responsible for coral energy acquisition in extreme low light environments, we examined Symbiodinium (endosymbiotic dinoflagellate) photobiological characteristics and the lipids and isotopic signatures from Symbiodinium and coral hosts over a depth‐dependent light gradient (55–7 μ mol photons m −2 s −1 , 60–132 m). Clear performance differences demonstrate different photoadaptation and photoacclimatization across this genus. Our results also show that flexibility in photoacclimatization depends primarily on Symbiodinium type. Colonies harboring Symbiodinium sp. COI‐2 showed significant increases in photosynthetic pigment content with increasing depth, whereas colonies harboring Symbiodinium spp. COI‐1 and COI‐3 showed variability in pigment composition, yield measurements for photosystem II, as well as size and density of Symbiodinium cells. Despite remarkable differences in photosynthetic adaptive strategies, there were no significant differences among lipids of Leptoseris species with depth. Finally, isotopic signatures of both host and Symbiodinium changed with depth, indicating that coral colonies acquired energy from different sources depending on depth. This study highlights the complexity in physiological adaptations within this symbiosis and the different strategies used by closely related mesophotic species to diversify energy acquisition and to successfully establish and compete in extreme light‐limited environments.

Padilla‐Gamiño, Jacqueline L.↗

Characterization of the neutron irradiation system for use in the Low-Dose-Rate Irradiation Facility at Sandia National Laboratories.

The objective of this work was to characterize the neutron irradiation system consisting of americium-241 beryllium (241AmBe) neutron sources placed in a polyethylene shielding for use at Sandia National Laboratories (SNL) Low Dose Rate Irradiation Facility (LDRIF). With a total activity of 0.3 TBq (9 Ci), the source consisted of three recycled 241AmBe sources of different activities that had been combined into a single source. The source in its polyethylene shielding will be used in neutron irradiation testing of components. The characterization of the source-shielding system was necessary to evaluate the radiation environment for future experiments. Characterization of the source was also necessary because the documentation for the three component sources and their relative alignment within the Special Form Capsule (SFC) was inadequate. The system consisting of the source and shielding was modeled using Monte Carlo N-Particle transport code (MCNP). The model was validated by benchmarking it against measurements using multiple techniques. To characterize the radiation fields over the full spatial geometry of the irradiation system, it was necessary to use a number of instruments of varying sensitivities. First, the computed photon radiography assisted in determining orientation of the component sources. With the capsule properly oriented inside the shielding, the neutron spectra were measured using a variety of techniques. A N-probe Microspec and a neutron Bubble Dosimeter Spectrometer (BDS) set were used to characterize the neutron spectra/field in several locations. In the third technique, neutron foil activation was used to ascertain the neutron spectra. A high purity germanium (HPGe) detector was used to characterize the photon spectrum. The experimentally measured spectra and the MCNP results compared well. Once the MCNP model was validated to an adequate level of confidence, parametric analyses was performed on the model to optimize for potential experimental configurations and neutron spectra for component irradiation. The final product of this work is a MCNP model validated by measurements, an overall understanding of neutron irradiation system including photon/neutron transport and effective dose rates throughout the system, and possible experimental configurations for future irradiation of components.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Prospects for ${B}_{(s)}^0 $ → π$^0$π$^0$ and ${B}_{(s)}^0 $ → ηη modes and corresponding CP asymmetries at Tera-Z

The physics potential of measuring $B^0_{(s)}$ → $π^0π^0$ and $B^0_{(s)}$ → $ηη$ decays via four-photon final states at Tera-Z phase of CEPC or FCC-ee is investigated in this paper. We propose an electromagnetic calorimeter (ECAL) with both high energy resolution and excellent separation power to efficiently reconstruct $π^0$ and $η$ from hadronic final states with high photon multiplicity. The resulting B-meson mass resolution is approximately 30 MeV, allowing 3 $σ$ separation between B 0 and $B^0_{(s)}$. With the assistance of the b-jet tagging, the relative sensitivities to B 0 → $π^0π^0$, $B^0_{(s)}$ → $π^0π^0$, B 0 → $ηη$, and $B^0_{(s)}$ → $ηη$ signal strengths at Tera-Z are projected as 0.45%, 4.5%, 18%, and 0.95%, respectively. Their dependence on various detector performances is also discussed. In addition, B 0 → $π^0π^0$ and its two isospin-related modes are paid special attention due to their roles in the determination of the CKM angle α (Φ 2 ). The anticipated precisions of their branching-ratio and CP-asymmetry measurements at Tera-Z are evaluated. We show that the measurement of the time-integrated B 0 → $π^0π^0$ CP asymmetry at Tera-Z is complementary to B-factory ones. The precision on α combining Z- and B-factory results reaches 0.4°, lower than the systematic uncertainties attached to isospin breaking.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Fully discrete schemes for monotone optimal control problems

In this article, we study an infinite horizon optimal control problem with monotone controls. We analyze the associated Hamilton–Jacobi–Bellman (HJB) variational inequality which characterizes the value function and consider the totally discretized problem using Lagrange elements to approximate the state space Ω. The convergence orders of these approximations are proved, which are in general (h+(k/(√h))){sup γ} where γ is the Hölder constant of the value function u, h and k are the time and space discretization parameters, respectively. A special election of the relations between h and k allows to obtain a convergence of order k{sup (2/3)γ}, which is valid without semiconcavity hypotheses over the problem’s data.

97 MATHEMATICS AND COMPUTING↗

Temperature Dependence of the Mechanical Properties of Equiatomic Solid Solution Alloys with FCC Crystal Structures

We found that compared to decades-old theories of strengthening in dilute solid solutions, the mechanical behavior of concentrated solid solutions is relatively poorly understood. A special subset of these materials includes alloys in which the constituent elements are present in equal atomic proportions, including the high-entropy alloys of recent interest. A unique characteristic of equiatomic alloys is the absence of “solvent” and “solute” atoms, resulting in a breakdown of the textbook picture of dislocations moving through a solvent lattice and encountering discrete solute obstacles. Likewise, to clarify the mechanical behavior of this interesting new class of materials, we investigate here a family of equiatomic binary, ternary and quaternary alloys based on the elements Fe, Ni, Co, Cr and Mn that were previously shown to be single-phase face-centered cubic (fcc) solid solutions. The alloys were arc-melted, drop-cast, homogenized, cold-rolled and recrystallized to produce equiaxed microstructures with comparable grain sizes. Tensile tests were performed at an engineering strain rate of 10 -3 s -1 at temperatures in the range 77–673 K. Unalloyed fcc Ni was processed similarly and tested for comparison. The flow stresses depend to varying degrees on temperature, with some (e.g. NiCoCr, NiCoCrMn and FeNiCoCr) exhibiting yield and ultimate strengths that increase strongly with decreasing temperature, while others (e.g. NiCo and Ni) exhibit very weak temperature dependencies. Moreover, to better understand this behavior, the temperature dependencies of the yield strength and strain hardening were analyzed separately. Lattice friction appears to be the predominant component of the temperature-dependent yield stress, possibly because the Peierls barrier height decreases with increasing temperature due to a thermally induced increase of dislocation width. In the early stages of plastic flow (5–13% strain, depending on material), the temperature dependence of strain hardening is due mainly to the temperature dependence of the shear modulus. In all the equiatomic alloys, ductility and strength increase with decreasing temperature down to 77 K. Keywords

36 MATERIALS SCIENCE↗

The Kummer tensor density in electrodynamics and in gravity

Guided by results in the premetric electrodynamics of local and linear media, we introduce on 4-dimensional spacetime the new abstract notion of a Kummer tensor density of rank four, K{sup ijkl}. This tensor density is, by definition, a cubic algebraic functional of a tensor density of rank four T{sup ijkl}, which is antisymmetric in its first two and its last two indices: T{sup ijkl}=−T{sup jikl}=−T{sup ijlk}. Thus, K∼T{sup 3}, see Eq. (46). (i) If T is identified with the electromagnetic response tensor of local and linear media, the Kummer tensor density encompasses the generalized Fresnel wave surfaces for propagating light. In the reversible case, the wave surfaces turn out to be Kummer surfaces as defined in algebraic geometry (Bateman 1910). (ii) If T is identified with the curvature tensor R{sup ijkl} of a Riemann–Cartan spacetime, then K∼R{sup 3} and, in the special case of general relativity, K reduces to the Kummer tensor of Zund (1969). This K is related to the principal null directions of the curvature. We discuss the properties of the general Kummer tensor density. In particular, we decompose K irreducibly under the 4-dimensional linear group GL(4,R) and, subsequently, under the Lorentz group SO(1,3)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the sub-band gap optical absorption in heat treated cadmium sulphide thin film deposited on glass by chemical bath deposition technique

The sub-band gap optical absorption in chemical bath deposited cadmium sulphide thin films annealed at different temperatures has been critically analyzed with special reference to Urbach relation. It has been found that the absorption co-efficient of the material in the sub-band gap region is nearly constant up to a certain critical value of the photon energy. However, as the photon energy exceeds the critical value, the absorption coefficient increases exponentially indicating the dominance of Urbach rule. The absorption coefficients in the constant absorption region and the Urbach region have been found to be sensitive to annealing temperature. A critical examination of the temperature dependence of the absorption coefficient indicates two different kinds of optical transitions to be operative in the sub-band gap region. After a careful analyses of SEM images, energy dispersive x-ray spectra, and the dc current-voltage characteristics, we conclude that the absorption spectra in the sub-band gap domain is possibly associated with optical transition processes involving deep levels and the grain boundary states of the material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-voltage polymer/small-molecule blend organic thin-film transistors and circuits fabricated via spray deposition

Organic thin-film electronics have long been considered an enticing candidate in achieving high-throughput manufacturing of low-power ubiquitous electronics. However, to achieve this goal, more work is required to reduce operating voltages and develop suitable mass-manufacture techniques. Here, we demonstrate low-voltage spray-cast organic thin-film transistors based on a semiconductor blend of 2,8-difluoro- 5,11-bis (triethylsilylethynyl) anthradithiophene and poly(triarylamine). Both semiconductor and dielectric films are deposited via successive spray deposition in ambient conditions (air with 40%–60% relative humidity) without any special precautions. Despite the simplicity of the deposition method, p-channel transistors with hole mobilities of >1 cm{sup 2}/Vs are realized at −4 V operation, and unipolar inverters operating at −6 V are demonstrated.

36 MATERIALS SCIENCE↗

PLANET FORMATION IN STELLAR BINARIES. II. OVERCOMING THE FRAGMENTATION BARRIER IN α CENTAURI AND γ CEPHEI-LIKE SYSTEMS

Planet formation in small-separation (∼20 AU) eccentric binaries such as γ Cephei or α Centauri is believed to be adversely affected by the presence of the stellar companion. Strong dynamical excitation of planetesimals by the eccentric companion can result in collisional destruction (rather than growth) of 1-100 km objects, giving rise to the ''fragmentation barrier'' for planet formation. We revise this issue using a novel description of secular dynamics of planetesimals in binaries, which accounts for the gravity of the eccentric, coplanar protoplanetary disk, as well as gas drag. By studying planetesimal collision outcomes, we show, in contrast to many previous studies, that planetesimal growth and subsequent formation of planets (including gas giants) in AU-scale orbits within ∼20 AU separation binaries may be possible, provided that the protoplanetary disks are massive (≳ 10{sup –2} M {sub ☉}) and only weakly eccentric (disk eccentricity ≲ 0.01). These requirements are compatible with both the existence of massive (several M{sub J} ) planets in γ Cep-like systems and the results of recent simulations of gaseous disks in eccentric binaries. Terrestrial and Neptune-like planets can also form in lower-mass disks at small (sub-AU) radii. We find that the fragmentation barrier is less of a problem in eccentric disks that are apsidally aligned with the binary orbit. Alignment gives rise to special locations, where (1) relative planetesimal velocities are low and (2) the timescale of their drag-induced radial drift is long. This causes planetesimal pileup at such locations in the disk and promotes their growth locally, helping to alleviate the timescale problem for core formation.

79 ASTRONOMY AND ASTROPHYSICS↗

Lorentz-violating gravitoelectromagnetism

The well-known analogy between a special limit of general relativity and electromagnetism is explored in the context of the Lorentz-violating standard-model extension. An analogy is developed for the minimal standard-model extension that connects a limit of the CPT-even component of the electromagnetic sector to the gravitational sector. We show that components of the post-Newtonian metric can be directly obtained from solutions to the electromagnetic sector. The method is illustrated with specific examples including static and rotating sources. Some unconventional effects that arise for Lorentz-violating electrostatics and magnetostatics have an analog in Lorentz-violating post-Newtonian gravity. In particular, we show that even for static sources, gravitomagnetic fields arise in the presence of Lorentz violation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Extreme Scale Visual Analytics

Extreme-scale visual analytics (VA) is about applying VA to extreme-scale data. The articles in this special issue examine advances related to extreme-scale VA problems, their analytical and computational challenges, and their real-world applications.

99 GENERAL AND MISCELLANEOUS↗

All-Atom Simulation of 3D Hot Spot Formation in Shocked TATB Explosive

TATB is an insensitive high explosive (IHE) critical to the stockpile that is challenging to model at the continuum scale. Advanced detonation models in the Cheetah high explosive chemistry code require validation though subscale simulations. High explosive initiation is determined by micron-scale physics of hot spots formed a shock-collapsed pores. Pore sizes between 100 nm and 1 μm are believed to be the most important for determining the shock sensitivity of TATB. This range of pore sizes is difficult to access at the atomic scale through allatom molecular dynamics (MD) simulations, even with Sierra-class computers. Quasi-2D simulations are widely used and allow much larger pore sizes (up to 400 nm) to be studied, but the applicability of 2D simulations to the actual 3D pore response is not understood. Resolving these uncertainties through “full physics” MD modeling is key for generalizing, parameterizing, and validating the kinds of continuum models used to inform design, safety, and performance. This work was a continuation of FY20 efforts pushing simulations to full 3D with the largest-ever all-atom simulations of an explosive. These were the first all-atom full-3D simulations of large hot spots thought to govern explosive detonation and required over a billion atoms. Simulations were performed using LAMMPS, an open SNL science code. MD explosive models present unique challenges, even for established codes such as LAMMPS. Their model forms are more complex than typical models for metals, while simulating high temperature-pressure conditions is demanding and increases computational cost. Scaling problems in GPU-enabled MD algorithms initially limited simulations to <100 million atoms but were resolved through collaboration with SNL. An overall 24x speedup was obtained relative to CPU machines. Specialized analysis of these simulations required a bottom-up refactoring and algorithm parallelization of in-house codes and application of computer vision algorithms to extract meaningful information.

36 MATERIALS SCIENCE↗

Energy: A special bibliography with indexes, April 1974

This literature survey of special energy and energy related documents lists 1708 reports, articles, and other documents introduced into the NASA scientific and technical information system between January 1, 1968, and December 31, 1973. Citations from International Aerospace Abstracts (IAA) and Scientific and Technical Aerospace Reports (STAR) are grouped according to the following subject categories: energy systems; solar energy; primary energy sources; secondary energy sources; energy conversion; energy transport, transmission, and distribution; and energy storage. The index section includes the subject, personal author, corporate source, contract, report, and accession indexes.

Source record↗

The community satellite. III

A number of technology experiments conducted with the satellite are discussed, giving attention to a very high resolution radiometer experiment, a radio frequency interference experiment, a millimeter wave propagation experiment, a COMSAT propagation experiment, a cesium bombardment ion engine experiment, an advanced thermal control flight experiment, a spacecraft attitude experiment, a radio beacon experiment, and environmental measurements experiments. Special investigations considered are related to the use of a spacecraft vibration accelerometer, a quartz crystal microbalance contamination monitor, and a television camera.

Source record↗

Symbolic Laplace transforms of special functions

A MACSYMA implementation of the Laplace transform for special functions is described. The generalized hypergeometric functions are used as a basis for the representation of approximately fifty special functions. Only a relatively small number of formulas that generally involve generalized hypergeometric functions are utilized for the integration stage. A sample of actual examples and their timing is provided.

Avgoustis, Y.↗