Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reentry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Electrostatic Probe Measurements of Plasma Surrounding Three 25,000 Foot Per Second Reentry Flight Experiments

A high-altitude electrostatic probe experiment is described and data are presented for three RAM C reentries at velocities of approximately 25 OOO feet per second. The electron density profiles inferred from the probe measurements are compared with theoretical calculations, and the probable cause of significant disagreement is briefly discussed. Probe measurements during material-addition sequences for radio-blackout alleviation are presented, and comparisons of probe measurements with other pertinent diagnostic measurements are made.

W Linwood Jones, Jr↗
NASA NTRS1958

Structural design considerations for boost-glide and orbital reentry vehicles

The preceding papers have discussed the aerodynamics and heating of several vehicles designed for atmospheric reentry from satellite orbits. Because of large heating inputs, some fundamental questions about the structure of these vehicles are also raised. Although there are many factors which influence structural design, only a brief examination of the relationship between heating input and structural weight is discussed here. For this purpose the heating inputs associated with the four vehicles shown in figure 1 are employed.

William A. Brooks, Jr.↗
NASA NTRS1971

Analysis of Free-Flight Laminar, Transitional, and Turbulent Heat-Transfer Results at Free-Stream Mach Numbers Near 20 (Reentry F)

Laminar, transitional, and turbulent heat-transfer data were measured during a reentry flight at a Mach number of 20 on a 5 deg half-angle cone 3.962 m (13 ft) long with an initial nose tip radius of 0.254 cm (0.1 in.). The free-stream Reynolds number increased during the prime data period from 7.0 x 10(exp 6) to 51.5 x 10(exp 6) per meter (2.1 x 10(exp 6) to 15.7 x 10(exp 6) per foot) and the ratio of wall to total temperature varied from 0.053 to 0.12. The angle of attack was less than 1deg for the prime data period. The experimental laminar and turbulent heating rates are compared with results from existing flat-plate prediction methods. At conditions of minimal tip blunting and angle of attack (above 26.8 km (88 000 ft)), values from a flat-plate laminar method agreed within 20 percent with the laminar data. The Schultz-Grunow skin-friction equation with reference enthalpy; conditions, with the Reynolds number based on distance from the transition location, and with the Colburn Reynolds analogy agreed within 10 percent with the experimental turbuleiit heating data. The Van Driest n skin-friction equation with Reynolds number greater than 10(exp 7) based on distance from the peak heating point and the Colburn Reynolds analogy was also within approximately 10 percent of the experimental turbulent heating data. A data correlation jbf the extent of transition and a simple empirical transition-zone heating correlation were also presented.

Zoby, Ernest V.↗
NASA NTRS1972

Reentry thermal protection from Pioneer F RTG insulation material

Ablation tests were performed on the insulation material used in the Pioneer F radioisotope thermoelectric generator (RTG) in the Ames Arc-Heated Planetary-Gas Wind Tunnel. Test results indicate that the material, trade name Min-K 1301, should experience little ablation for heat transfer rates below 40 BTU/sq ft-sec. If the current design were to be changed so that the various pieces of Min-K were fastened or interlocked together the total amount of heat delivered to the RTG heat source during an earth orbital decay reentry would be reduced by at least 22.7%.

Vorreiter, J. W.↗
NASA NTRS1971

Application of the steepest ascent optimization method to a reentry trajectory problem

The direct optimization method is presented in detail. Nominal values of the control variables are input parameters. Perturbations are introduced into the control variables and the resulting first order predictions of changes in the payoff, and constraint functions are then determined. Through a sequence of prescribed cycles, a trajectory is eventually obtained which is reasonably close to the optimum. The method is successfully applied to an Apollo three-dimensional reentry problem. The study of this Apollo application problem has resulted in the development of a highly flexible computer program that can be modified to consider other trajectory optimization problems.

Junkin, B. G.↗