Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Structure and Superconductivity of Hydrogenated TiZr Alloys Under High Pressure

The effects of pressure on the structure and electrical transport properties, including electrical resistance and critical magnetic field values for superconductivity in pristine and hydrogenated TiZr alloys, were investigated. As pressure increased from ambient to 55 GPa, the structure of the pristine TiZr alloys transformed from hcp to bcc via an intermediate ω phase. The superconducting transition temperature (T c ) significantly increased from 1.76 K at ambient pressure to 15.5 K at 52.2 GPa, accompanied by an extrapolated upper critical field of 24.5 T at T = 0 K. In contrast, the hydrogenated samples exhibited substantially lower T c values compared to the pristine ones, with a T c of 4.6 K at 50.5 GPa and an extrapolated upper critical field of 1.8 T at T = 0 K. Upon decompression, the superconductivity in the hydrogenated sample persisted down to 25 GPa, disappearing when the pressure was reduced to 19 GPa. Synchrotron X-ray diffractions (XRD) analysis revealed the formation of three hydrides: I4/mmm-(Ti, Zr)H 2 , P6 3 /mmc-(Ti, Zr)H 3 , and I4̅3d-(Ti,Zr) 4 H 15 . Finally, by combining XRD and electrical resistance data, we tentatively propose that the P6 3 /mmc-(Ti, Zr)H 3 predominantly induces superconductivity. In contrast to superhydrides, where electron–phonon interactions increase the superconducting temperature at high pressure, hydrogen atoms in hcp-(Ti, Zr)H 3 reduce T c .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Photoluminescence of Cr 3+ in β-Ga 2 O 3 and (Al 0.1 Ga 0.9 ) 2 O 3 under pressure

The effects of pressure on single crystals of Cr-doped gallium oxide (β-Ga 2 O 3 :Cr 3+ ) and aluminum gallium oxide [(Al 0.1 Ga 0.9 ) 2 O 3 ] were examined by measuring the wavelength shift in the spectral R lines. Photoluminescence (PL) spectra of these materials were collected from samples in diamond anvil cells at pressures up to 9 GPa. The β-Ga 2 O 3 :Cr 3+ R lines were found to shift linearly under hydrostatic pressure. The (Al 0.1 Ga 0.9 ) 2 O 3 R lines also show a linear shift but the R 1 line shifted less than for β-Ga 2 O 3 :Cr 3+ . The ratio of R 2 to R 1 peak areas vs pressure is dominated by nonradiative recombination. X-ray diffraction measurements of (Al 0.1 Ga 0.9 ) 2 O 3 indicate that its equation of state is similar to that of β-Ga 2 O 3 . β-Ga 2 O 3 :Cr 3+ was examined under non-hydrostatic conditions by using mineral oil as a pressure transmitting medium. Similar to the case in ruby, the R 1 line is much more sensitive to non-hydrostatic stress than R 2 . Spatially resolved PL of a sample at 8 GPa in mineral oil showed significant variations in the R 1 emission wavelength. Furthermore, these results suggest that the R 1 line can serve as a sensitive probe of alloy composition and non-hydrostatic stress, while the R 2 line is insensitive to these perturbations.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Dynamics and control of orbiting flexible beams and platforms under the influence of solar radiation and thermal effects

Expressions for thermal deflections of uniform thin beams and plates exposed to solar heating are obtained as a function of the properties of the material and the solar incidence angle. The major effect of the solar radiation pressure interacting with the thermally deformed structure is found to give rise to disturbance moments on the structure. The thermal deformations of the structures are assumed to be within 0.1 percent of the characteristic length of the structure. With the assumed thermal deformations, the resulting uncontrolled transient responses of these geosynchronous orbiting structures to the solar radiation pressure induced disturbances are simulated. The resulting rigid modal oscillations are found to be an order of magnitude larger than for those cases previously considered in which only the solar radiation pressure effect on vibrating structures was treated. Modifications of control laws and/or the feedback gain values are considered in order to improve the transient response characteristics under the thermally induced disturbances.

Krishna, R.↗
NASA NTRS1992

CN radical reactions with hydrogen cyanide and cyanogen - Comparison of theory and experiment

The method of laser photolysis/laser-induced fluorescence is used to obtain absolute rate constants for CN radical reactions with HCN and C2N2. The rate constants were found to be temperature-dependent in the range 300-740 K and pressure independent in the range 100-600 Torr. Rice-Remsperger-Kassel-Marcus theory for both reactions employing the transition state parameters obtained by the BAC-MP4 method are made. These calculations yielded reasonable results for the CN + HCN reaction, predicting both the temperature dependence and pressure independence. No pressure effect was observed in the pressure range 100-1000 Torr at temperatures below 900 K, confirming the experimental results.

Yang, D. L.↗
NASA NTRS1959

Fluid-Dynamic Properties of Some Simple Sharp- and Blunt-Nosed Shapes at Mach Numbers from 16 to 24 in Helium Flow

The fluid-dynamic characteristics of flat plates, 5 deg and 10 deg wedges, and 5 deg and 10 deg cones have been investigated at Mach numbers from 16.3 to 23.9 in helium flow. The flat-plate results are for a leading-edge Reynolds number range of 584 to 19,500 and show that the induced pressure distribution is essentially linear with the hypersonic viscous interaction parameter bar X within the scope of this investigation. It is also shown that the rate at which the induced pressure varies with bar X is a linear function of the leading-edge Reynolds number. The wedge and cone results show that as the flow-deflection angle increases, the induced-pressure effects decrease and the measured pressures approach those predicted by inviscid shock theory.

Henderson, Arthur, Jr.↗
DOE OSTI2024

Temperature effect on turbulent burning velocity of lean premixed hydrogen/air flames

Hydrogen has drawn great attention in recent years as a carbon-free fuel. The turbulent burning velocity (S T ) is an important parameter for the design and modeling of hydrogen-fueled engines given the high propagation speed of hydrogen flames. It has been well documented that S T of hydrogen flames can be dramatically increased by thermo-diffusive effects which are sensitive to thermodynamic conditions. Previous studies have mainly focused on the pressure effect on S T of lean hydrogen flames, while the temperature effect has been largely ignored. Here, in the present study, the turbulent burning velocity for a lean hydrogen/air mixture over a wide range of temperatures (300–641 K) and pressures (1–15 atm) is investigated through direct numerical simulations of statistically planar turbulent premixed flames. Results show that the variation of normalized turbulent burning velocity (S T /S L , where S L is the laminar flame speed) with temperature and pressure is mainly controlled by the variation of the stretching factor I 0 . While S T /S L is only marginally dependent on temperature at the atmospheric pressure, it exhibits a decreasing trend with temperature at an elevated pressure (10 atm). This is associated with different temperature dependencies of flame surface area enlargement at the two different pressures, despite the monotonically decreasing trends of I 0 with temperature at both pressures. In addition, under engine-relevant conditions where the temperature and pressure increase simultaneously, the promotion effect of pressure is found to be largely canceled out by the suppression effect of temperature, leading to only a slight increase in I 0 and S T /S L . The observed trends are further explained through detailed flame dynamic analysis. Furthermore, I 0 at different temperatures and pressures is found to correlate very well with the enhancement of fuel consumption rate in the critically strained laminar flames. The present study elucidates the strong impact of temperature on S T of lean premixed hydrogen/air flames at elevated pressures and provides new insights into the modeling of S T , especially for engine-relevant conditions.

Wang, Yiqing [Argonne National Laboratory (ANL), A↗
NASA NTRS1959

Overexpanded Performance of Conical Nozzles with Area Ratios of 6 and 9 With and Without Supersonic External Flow

An investigation of the thrust characteristics and internal pressure distributions of two convergent-divergent 15 deg. half-angle exhaust nozzles having area ratios of 6 and 9 was made in the NASA Lewis 10- by 10-foot supersonic wind tunnel. The tests were conducted at free-stream Mach numbers of 0, 2.0, 2.5, 3.0, and 3.5 over a range of nozzle pressure ratios from 3 to 105. Attempts were made to induce separation of the overexpanded nozzle flow using secondary airflow and a wedge. Nozzle flow expansion under all free-stream conditions followed one-dimensional theory until separation from the nozzle wall occurred. In quiescent air the nozzle flow expanded to a pressure approximately one-half the base pressure before separation. When the nozzles were tested with supersonic external flow at the same effective pressure ratios, the nozzle flow separated with negligible expansion below the base pressure. The effect of a supersonic stream on internal nozzle flow separation characteristics was well defined only at a free-stream Mach number of 2.0. Thrust data at supersonic free-stream conditions indicate that only a small percentage of the ideal nozzle thrust will be available at nozzle pressure ratios below design. However, the overexpanded primary nozzle thrust loss was decreased by injecting large quantities of secondary air near the nozzle exit. In most cases no net gain in thrust resulted from secondary-air injection when the nozzle thrust was compared with the ideal thrust of both the primary and secondary airflows.

Musial, Norman T.↗
DOE OSTI2020

Melting of Magnesium Borohydride under High Hydrogen Pressure: Thermodynamic Stability and Effects of Nanoconfinement

The thermodynamic stability and melting point of magnesium borohydride were probed under hydrogen pressures up to 1000 bar (100 MPa) and temperatures up to 400 °C. At 400 °C, Mg(BH4)2 was found to be chemically stable between 700 and 1000 bar H2, whereas under 350 bar H2 or lower pressures, the bulk material partially decomposed into MgH2 and MgB12H12. The melting point of solvent-free Mg(BH4)2 was estimated to be 367-375 °C, which was above previously reported values by 40-90 °C. Our results indicated that a high hydrogen backpressure is needed to prevent the decomposition of Mg(BH4)2 before measuring the melting point and that molten Mg(BH4)2 can exist as a stable liquid phase between 367 and 400 °C under hydrogen overpressures of 700 bar or above. The occurrence of a pure molten Mg(BH4)2 phase enabled efficient melt-infiltration of Mg(BH4)2 into the pores of porous templated carbons (CMK-3 and CMK-8) and graphene aerogels. Both transmission electron microscopy and small-angle X-ray scattering confirmed efficient incorporation of the borohydride into the carbon pores. The Mg(BH4)2@carbon samples exhibited comparable hydrogen capacities to bulk Mg(BH4)2 upon desorption up to 390 °C based on the mass of the active component; the onset of hydrogen release was reduced by 15-25 °C compared to the bulk. Importantly, melt-infiltration under hydrogen pressure was shown to be an efficient way to introduce metal borohydrides into the pores of carbon-based materials, helping to prevent particle agglomeration and formation of stable closo-polyborate byproducts.

White, James L.↗
DOE OSTI2020

Combustion, criteria pollutant and soot property assessment of mixing-controlled high-load engine operation with gasoline and diesel

Gasoline compression ignition (GCI) is an emerging technology that can achieve high fuel efficiency and low criteria emissions in diesel engine platforms using gasoline and gasoline-like fuels. While low- and mid-range loads are enabled with low temperature combustion (LTC) approaches, high-loads are more efficient with high temperature combustion (HTC) requiring mixing-controlled combustion (MCC). Lower soot emissions are achieved with gasoline even in high-load MCC than with diesel, but detailed soot properties from gasoline and diesel have been rarely discussed. In order to better understand how high-load operations affect soot properties, in this study gasoline and diesel were tested in a six-cylinder heavy duty engine at 14 bar brake mean effective pressure (BMEP) at similar combustion phasing. Effects of pilot mass ratio and EGR on heat release rates, cylinder temperatures, ignition delay (ID) and combustion duration (CD) were examined, relating with emissions variations with applications of the two fuels. Soot mass and particle number emissions were slightly lower with gasoline than with diesel, resulting in a more favorable NOx-soot trade-off with gasoline like other reports. Contrary to other findings in the literature, gasoline and diesel soot samples presented similar particle distribution shapes, carbon crystalline structures and primary particle sizes, regardless of fuel type and EGR rate. Consequently, the current result proposes that soot particles have undergone similar soot formation and oxidation processes despite reactivity difference and oxygen availability under the examined high-load MCC with similar combustion phases.

02 PETROLEUM↗