SEARCH · Engineering Papers

Results for “Phase slips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Tangleproof Coupling

Along with Marshall Space Flight Center, Phase 2 Automation developed a unique rotary coupling capable of connecting a large number of electrical cables to a turntable without stressing the cables or tangling them. Device accommodates 246 cables and allows the turntable to rotate through an arc of 320 degrees. At extremes of rotation the cables remain loose enough so that they are not pulled taut and overstressed; a halfway rotation, the cables are not so loose that they tangle. The rotary connector was developed to carry electrical signals to and from a telescope platform on the satellite without employing a complex set of slip rings which are electrically noisy and could have caused signal interference.

Source record↗

NASA NTRS2003

Modeling Candle Flame Behavior In Variable Gravity

The burning of a candle, as typical non-propagating diffusion flame, has been used by a number of researchers to study the effects of electric fields on flame, spontaneous flame oscillation and flickering phenomena, and flame extinction. In normal gravity, the heat released from combustion creates buoyant convection that draws oxygen into the flame. The strength of the buoyant flow depends on the gravitational level and it is expected that the flame shape, size and candle burning rate will vary with gravity. Experimentally, there exist studies of candle burning in enhanced gravity (i.e. higher than normal earth gravity, g(sub e)), and in microgravity in drop towers and space-based facilities. There are, however, no reported experimental data on candle burning in partial gravity (g < g(sub e)). In a previous numerical model of the candle flame, buoyant forces were neglected. The treatment of momentum equation was simplified using a potential flow approximation. Although the predicted flame characteristics agreed well with the experimental results, the model cannot be extended to cases with buoyant flows. In addition, because of the use of potential flow, no-slip boundary condition is not satisfied on the wick surface. So there is some uncertainty on the accuracy of the predicted flow field. In the present modeling effort, the full Navier-Stokes momentum equations with body force term is included. This enables us to study the effect of gravity on candle flames (with zero gravity as the limiting case). In addition, we consider radiation effects in more detail by solving the radiation transfer equation. In the previous study, flame radiation is treated as a simple loss term in the energy equation. Emphasis of the present model is on the gas-phase processes. Therefore, the detailed heat and mass transfer phenomena inside the porous wick are not treated. Instead, it is assumed that a thin layer of liquid fuel coated the entire wick surface during the burning process. This is the limiting case that the mass transfer process in the wick is much faster than the evaporation process at the wick surface.

Alsairafi, A.↗

DOE OSTI2022

Resolving the Martensitic Transformation in Q&P Steels In-Situ at Dynamic Strain Rates Using Synchrotron X-ray Diffraction

Herein the dynamic deformation response of two quenching and partitioning (Q&P) steels was investigated using a high strain rate tension pressure bar and in-situ synchrotron radiography and diffraction. This allowed for concurrent measurements of the martensitic transformation, the elastic strains/stresses on the martensite and ferrite, and the bulk mechanical behavior. The steel with the greater fraction of ferrite exhibited greater ductility and lower strength, suggesting that dislocation slip in ferrite enhanced the deformability. Meanwhile, the kinetics of the martensitic transformation appeared similar for both steels, although the steel with a greater ferrite fraction retained more austenite in the neck after fracture.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Elemental segregation to lattice defects in the CrMnFeCoNi high-entropy alloy during high temperature exposures

The influence of small plastic pre-strains on the elevated-temperature stability and microstructure of the equiatomic CrMnFeCoNi FCC solid solution is investigated. Particular attention is given to whether any of the alloy elements segregate to individual dislocations. To that end, CrMnFeCoNi samples were first deformed in tension at room temperature to plastic strains of 0.2 and 2.3%, and subsequently annealed at 973 K for 800 hours. The pre-strains activated planar slip of 1/2<110>-type dislocations on {111}-type glide planes. Interactions of this planar slip with special Σ3 grain boundaries formed a large number of dislocation segments with a <110>-type crystallographic orientation suitable for a credible end-on analysis of dislocation cores in HR-STEM. The cores of the 1/2<110> dislocations pushed up against the investigated grain boundaries were found to be close to the compact configuration. Within the sensitivity of the Super-X EDS mapping, no concentration gradient was detected near dislocations that would indicate enrichment at dislocation cores of any of the elemental constituents of the alloy after the pre-deformation and annealing. However, a Cr-rich tetragonal sigma phase nucleated and grew at grain boundary triple junctions during this anneal, processes that were not accelerated by the enhanced dislocation density present after pre-strain. A clear chromium gradient was observed in the Cr-depleted zones near grain boundaries suggesting that Cr transport occurred by relatively slow diffusion from the bulk to the grain boundaries and then by relatively fast diffusion along the grain boundaries to the precipitates. Accompanying the Cr depletion near grain boundaries is a simultaneous Ni and Mn enrichment, which promotes formation of the L1 0 NiMn phase that is observed on the grain boundaries after prolonged annealing.

36 MATERIALS SCIENCE↗

DOE OSTI2023

A sensitivity analysis of twinning crystal plasticity finite element model using single crystal and poly crystal Zircaloy

The popularity of crystal plasticity finite element method (CPFEM) models is increasing due to their ability to predict the mechanical response of crystalline materials such as metals and metal alloys more accurately than traditional continuum mechanics models. This is since the crystal plasticity models consider the effect of atomic structure, microstructural morphology, and properties of individual grains. These CPFEM models use a large number of material parameters in order to capture the mesoscale physics which comes with the downside of the tedious calibration process. In this paper, a CPFEM code was developed to include the twinning induced grain reorientation and subsequent crystallographic slip for HPC material. The developed code is incorporated in a large-scale, parallelized nonlinear solver WARP3D. Further, a sensitivity analysis with respect to 22 material parameters was then conducted using single crystal and polycrystal representative volume element (RVE) of Zircaloy material. Loading was applied along five different crystallographic orientations for single crystal RVE and along three directions namely, rolling (RD), transverse (TD), and normal (ND) direction for polycrystal RVE. Results obtained from the sensitivity analysis were used for the calibration of material parameters for Zircaloy. Finally, developed code along with calibrated material parameters was used to investigate the effect of the hydride phase formation in Zircaloy which is a typical case observed for nuclear applications. It was found that the volume fraction of the hydride phase has a significant impact on the mechanical properties of Zircaloy.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Kink bands promote exceptional fracture resistance in a NbTaTiHf refractory medium-entropy alloy

Single-phase body-centered cubic (bcc) refractory medium- or high-entropy alloys can retain compressive strength at elevated temperatures but suffer from extremely low tensile ductility and fracture toughness. We examined the strength and fracture toughness of a bcc refractory alloy, NbTaTiHf, from 77 to 1473 kelvin. This alloy’s behavior differed from that of comparable systems by having fracture toughness over 253 MPa·m 1/2 , which we attribute to a dynamic competition between screw and edge dislocations in controlling the plasticity at a crack tip. Whereas the glide and intersection of screw and mixed dislocations promotes strain hardening controlling uniform deformation, the coordinated slip of <111> edge dislocations with {110} and {112} glide planes prolongs nonuniform strain through formation of kink bands. These bands suppress strain hardening by reorienting microscale bands of the crystal along directions of higher resolved shear stress and continually nucleate to accommodate localized strain and distribute damage away from a crack tip.

36 MATERIALS SCIENCE↗

NASA NTRS2007

Simulation of a Synthetic Jet in Quiescent Air Using TLNS3D Flow Code

Although the actuator geometry is highly three-dimensional, the outer flowfield is nominally two-dimensional because of the high aspect ratio of the rectangular slot. For the present study, this configuration is modeled as a two-dimensional problem. A multi-block structured grid available at the CFDVAL2004 website is used as a baseline grid. The periodic motion of the diaphragm is simulated by specifying a sinusoidal velocity at the diaphragm surface with a frequency of 450 Hz, corresponding to the experimental setup. The amplitude is chosen so that the maximum Mach number at the jet exit is approximately 0.1, to replicate the experimental conditions. At the solid walls zero slip, zero injection, adiabatic temperature and zero pressure gradient conditions are imposed. In the external region, symmetry conditions are imposed on the side (vertical) boundaries and far-field conditions are imposed on the top boundary. A nominal free-stream Mach number of 0.001 is imposed in the free stream to simulate incompressible flow conditions in the TLNS3D code, which solves compressible flow equations. The code was run in unsteady (URANS) mode until the periodicity was established. The time-mean quantities were obtained by running the code for at least another 15 periods and averaging the flow quantities over these periods. The phase-locked average of flow quantities were assumed to be coincident with their values during the last full time period.

Vatsa, Veer N.↗

NASA NTRSDate not supplied

Variation in Predicted Orbital Lifetime Due to Launch Year

We present trends in predicted orbital lifetimes of CubeSats based not only on orbital parameters, but also launch year and the Area-to-Mass (AtM) ratio of the CubeSat. Determining the orbital lifetime variation of CubeSats in low-Earth orbit (LEO) is an important aspect of mission planning because of two competing factors: (1) the maximum orbital lifetime for orbital debris mitigation requirements, and (2) the minimum orbit duration necessary to accomplish the spacecraft mission requirements. The orbital lifetime is a function of orbital parameters, the AtM ratio of the CubeSat, and date of orbit insertion. Solar flux varies with time, peaking and declining across the 11-year solar cycle and affecting the amount of atmospheric drag on the CubeSat. This results in large variations in orbital lifetime dependent on the mission's launch date. We calculated the variation of orbital lifetime for multiple commonly used 1U to 6U CubeSat mission types across the two upcoming solar cycles. For any given AtM ratio and altitude combination in this analysis, the predicted orbital lifetime varies up to a factor of five due to orbit insertion occurring in a different year. Some examples of orbital lifetime spreads are 5 months to 2 years, and 1.5 to 7.5 years. While orbital lifetimes correlate to the solar cycle, the phasing of the maximum values varies based on a given AtM ratio and altitude combination. Different combinations of these two factors will result in the maximum predicted orbital lifetime occurring at different launch years throughout the solar cycle. Therefore, there is not a specific year within a solar cycle which can be used to calculate the maximum predicted orbital lifetime for all CubeSats. Since CubeSats are typically flown as a rideshare payload on a launch vehicle, mission planners must account for launch date variation in their orbital lifetime predictions. We recommend calculating orbital lifetime for a range of dates to allow for risk planning due to launch date slips, and other mission planning best practices.

CubeSat↗

DOE OSTI2024

Formation of hierarchically structured martensites in pure iron with ultrahigh strength and stiffness

Strong steels are primarily fabricated by introducing spatial obstacles (e.g., stacking faults and precipitates) that inhibit dislocation slips under stress to achieve high strength. However, for most low-carbon steels, such obstacles are difficult to form mainly because the martensitic transition is kinetically unfavorable by conventional methods, which precludes the attainment of high-strength materials in these steels with low solute contents. Here, we report an innovative high-pressure preparation of martensitic pure Fe with involving nano-effect, which leads to the formation of ultrastrong bulk iron with exceptionally high yield strength, ultimate strength, and hardness of 2.9 GPa, 3.7 GPa, and 9.0 GPa, respectively, exceeding those of high-speed steels. Such extraordinary mechanical properties are closely attributed to its high-density martensites with unique multiscale hierarchical structures formed due to complex phase transitions under pressure.

Science & Technology - Other Topics↗

NASA NTRS2005

NASA Tech Briefs, September 2005

Topivs include: Diamond-Coated Carbon Nanotubes for Efficient Field Emission; Improved Anode Coatings for Direct Methanol Fuel Cells; Advanced Ablative Insulators and Methods of Making Them; PETIs as High-Temperature Resin-Transfer-Molding Materials; Stable Polyimides for Terrestrial and Space Uses; Low-Density, Aerogel-Filled Thermal-Insulation Tiles; High-Performance Polymers Having Low Melt Viscosities; Nonflammable, Hydrophobic Aerogel Composites for Insulation; Front-Side Microstrip Line Feeding a Raised Antenna Patch; Medium-Frequency Pseudonoise Georadar; Facilitating Navigation Through Large Archives; Program for Weibull Analysis of Fatigue Data; Comprehensive Micromechanics-Analysis Code - Version 4.0; Component-Based Visualization System; Software for Engineering Simulations of a Spacecraft; LabVIEW Interface for PCI-SpaceWire Interface Card; Path Following with Slip Compensation for a Mars Rover; International Space Station Electric Power System Performance Code-SPACE; Software for Automation of Real-Time Agents, Version 2; Software for Optimizing Plans Involving Interdependent Goals; Computing Gravitational Fields of Finite-Sized Bodies; Custom Sky-Image Mosaics from NASA's Information Power Grid; ANTLR Tree Grammar Generator and Extensions; Generic Kalman Filter Software; Alignment Stage for a Cryogenic Dilatometer; Rugged Iris Mechanism; Treatments To Produce Stabilized Aluminum Mirrors for Cryogenic Uses; Making AlNx Tunnel Barriers Using a Low-Energy Nitrogen-Ion Beam; Making Wide-IF SIS Mixers with Suspended Metal-Beam Leads; Sol-Gel Glass Holographic Light-Shaping Diffusers; Automated Counting of Particles To Quantify Cleanliness; Phase Correction for GPS Antenna with Nonunique Phase Center; Compact Infrasonic Windscreen; Broadband External-Cavity Diode Laser; High-Efficiency Solar Cells Using Photonic-Bandgap Materials; Generating Solid Models from Topographical Data; Computationally Lightweight Air-Traffic-Control Simulation; Spool Valve for Switching Air Flows Between Two Beds; Partial Model of Insulator/ Insulator Contact Charging; Asymmetric Electrostatic Radiation Shielding for Spacecraft; and Reusable Hybrid Propellant Modules for Outer-Space Transport.

Source record↗

DOE OSTI2023

Interface microstructure effects on dynamic failure behavior of layered Cu/Ta microstructures

Abstract Structural metallic materials with interfaces of immiscible materials provide opportunities to design and tailor the microstructures for desired mechanical behavior. Metallic microstructures with plasticity contributors of the FCC and BCC phases show significant promise for damage-tolerant applications due to their enhanced strengths and thermal stability. A fundamental understanding of the dynamic failure behavior is needed to design and tailor these microstructures with desired mechanical responses under extreme environments. This study uses molecular dynamics (MD) simulations to characterize plasticity contributors for various interface microstructures and the damage evolution behavior of FCC/BCC laminate microstructures. This study uses six model Cu/Ta interface systems with different orientation relationships that are as- created, and pre-deformed to understand the modifications in the plasticity contributions and the void nucleation/evolution behavior. The results suggest that pre-existing misfit dislocations and loading orientations (perpendicular to and parallel to the interface) affect the activation of primary and secondary slip systems. The dynamic strengths are observed to correlate with the energy of the interfaces, with the strengths being highest for low-energy interfaces and lowest for high-energy interfaces. However, the presence of pre-deformation of these interface microstructures affects not only the dynamic strength of the microstructures but also the correlation with interface energy.

42 ENGINEERING↗

DOE OSTI2020

NH 4 OH Looping with Membrane CO 2 Absorber and Distributed Stripper for Enhanced Algae Growth

The University of Kentucky Center for Applied Energy (UK CAER) has devised a unique, integrated CO2 capture and utilization technology. CO2 from coal-fired power generation flue gas is first captured at half the operating cost of a typical aqueous CO2 capture system (CCS), distributed in an aqueous stream and then fixed by algae in bioreactors where the algae production is increased by 50% over that with a typical intermittent nutrient feeding system. Lower CCS operating cost is achieved by eliminating the flue gas pretreatment step for cooling and SO2 removal, eliminating steam extraction from the power generation steam cycle for solvent regeneration, and eliminating CO2 compression. Higher algae production is achieved by continuous, just-in-time nutrient feed to the bioreactors directly from a distributed solvent regenerator, which maintains the bioreactor pH for optimum growth. The process starts with a uniquely configured membrane absorber, where the flue gas is indirectly contacted with an ammonium hydroxide (NH4OH) solvent. Dissolved NH3 is attractive for both CO2 capture and as an algae nutrient. For CO2 capture it is inexpensive, has a low regeneration energy, is thermally- and oxidatively-stable and has a viscosity near that of water, which makes is easy to transport. Numerous studies have shown that the scrubbing capacity of NH3 is approximately 0.9-1.2 kg of CO2/kg of NH3, with a CO2 removal efficiency of ~99% and half the solvent regeneration energy than that of 30 wt% MEA[1, 2, 3]. NH3 is attractive as an algae nutrient due to its low cost. The rich NH4OH solvent is pumped to a set of distributed regenerators which are co-located with the algae bioreactors. Solvent pumping, transport and distribution reduces the balance of plant (BOP) cost compared to a typical aqueous CCS related to the flue gas duct and boost fan required to transport the flue gas. The energy required for the distributed solvent regeneration is supplied by solar-thermal panels eliminating the need for steam extraction from the power generation steam cycle. After solvent regeneration, the product stream contains both the CO2 captured from the flue gas and volatized NH3 from the solvent. This product stream is fed directly to the bioreactors, eliminating the need for compression of the CO2 stream. The relative amounts of CO2 and NH3 in the product stream are adjusted and controlled by a controlling the regeneration conditions (pressure and temperature). The continuous feed of the right ratio of nutrients overcomes the typical inhibition of algae growth resulting from frequent pH swings in the bioreactor due to unbalanced (intermittent) feeding systems for CO2 and N. Also, because the regenerators will operate at pressure and be located in close proximity to the bioreactors, there is no worry about pressure drop when sparging the gas into the algae. Sparging produces small bubbles which is beneficial for mass transfer efficiency. One known challenge when using an NH4OH solvent is high NH3 emission. Hydrophobic membranes are used for CO2 capture using an aqueous NH3 solution[4, 5] without the direct contact between flue gas and aqueous solution. Additionally, UK CAER CO2 capture and utilization process manages NH3 slip in three extra measures. First, NH3 slip is minimized by working with minimal species partial pressure, which is proportional to the concentration in the liquid. Hence, lowering the capture solvent concentration will lower the NH3 partial pressure. Second, UK CAER’s previous work has demonstrated that the addition of Zn2+ into NH3 solutions to chelate the NH3 can reduce NH3 volatility. Third, the configuration of the membrane CO2 absorber utilizes condensed water from the flue gas to continually wash the gas-side of the membrane to reduce fouling and recapture NH3 slip. Additional details about the UK CAER unique, integrated CO2 capture and utilization technology will be presented along with technology development plans. Diao, N., Q. Li, and Z. Fang. 2004. Heat transfer in ground heat exchangers with groundwater advection. International Journal of Thermal Sciences. 43: 1203-1211, He, Q., M. Chen, L. Meng, K. Liu, and W. Pan. 2004. Study on Carbon Dioxide Removal from Flue Gas by Absorption of Aqueous Ammonia. Western Kentucky University. Yeh, A.C., and H. Bai. 1999. Comparison of ammonia and monoethanolamine solvents to reduce CO2 greenhouse gas emissions. The Science of the Total Environment. 228: 121-133, Villeneuve, K., D. Roizard, J.C. Remigy, M. Iacono, and S. Rode. 2018. CO2 capture by aqueous ammonia with hollow fiber membrane contactors: Gas phase reactions and performance stability. Separation and Purification Technology, 199: 189-197, Toro Molina, C., and C. Bouallou. 2016. Carbon dioxide absorption by ammonia intensified with membrane contactors. Clean Techn Environ Policy 18, 2133–2146 (2016)

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Utah FORGE: Fault Shear Reactivation Experimental Data for Fluid Injection-Rate Controls on Seismic Moment

Included are experimental data recorded from shear experiments that specifically explore the link between fluid-injection rate and seismic moment resulting from shear reactivation of laboratory faults. Raw mechanical data from three experiments are included alongside corresponding MATLAB scripts that import and plot the data, as well as use it to calculate shear and normal stress. Experiments are performed on 2.5-3 inch long granitoid cores from the Utah FORGE EGS demonstration site, containing a single inclined fracture with small-scale roughness added to the fracture surface. The raw data included here were recorded from an aluminum triaxial pressure vessel (TEMCO) configured with three independent servo-controlled pumps, with distilled water used as the working fluid. The pumps control confining pressure, upstream pore pressure, and axial pressure, with each pump connected to a LabView interface to record applied pressures, cumulative injected water volumes, and pump flow rates. The downstream outlet from the fracture is closed to allow pressurization, which is measured by an external pressure transducer. A linear variable differential transformer (LVDT) attached to the axial piston measures axial displacement, from which we calculate shear displacement along the fracture. Additionally, P-wave transducers are used to record acoustic signatures, where acoustic emission events and maximum amplitudes are compared against seismic moment and shear slip velocity. Fluid injection rates range between 0.05 mL/min, 0.25 mL/min, and 0.75 mL/min for each experiment. Along-fault pressure distributions are progressively less uniform as injection rates increase, representing a switch from steady-state to transient conditions. Triggered shear displacement is used as a proxy for seismic moment and is indexed against cumulative injection volume and rate. Each experiment is performed under constant shear stress conditions, and the sample is fully saturated with DI water. Axial and confining stresses are applied to 3 MPa through pressure-stepping in 500 kPa increments. The pore pressure is held constant at 200 kPa prior to initiating the experiment, and initial axial displacement is recorded. The axial stress is then increased to initiate shear mobilization during the loading phase (run-in) until a peak steady state is achieved. The initial shear stress is reduced to approximately 80% of the peak shear stress by decreasing the axial stress, then held constant for the duration of each experiment.

15 GEOTHERMAL ENERGY↗

DOE OSTI2025

Spherical and sessile droplet dynamics by fluctuating hydrodynamics

We simulate the mesoscopic dynamics of droplets formed by phase-separated fluids at nanometer scales where thermal fluctuations are significant. Both spherical droplets fully immersed in a second fluid and sessile droplets which are also in contact with a solid surface are studied. Our model combines a Cahn–Hilliard formulation with incompressible fluctuating hydrodynamics; for sessile droplets, the fluid–solid contact angle is specified as a boundary condition. Deterministic simulations with an applied body force are used to measure the droplets' mobility from which a diffusion coefficient is obtained using the Einstein relation. Stochastic simulations are independently used to obtain a diffusion coefficient from a linear fit of the variance of a droplet's position with time. In some scenarios, these two measurements give the same value but not in the case of a spherical droplet initialized near a slip wall or in the case of sessile droplets with large contact angles (≥90°) on both slip and no-slip surfaces.

Bell, John B↗

NASA NTRS1995

Temperature Dependent Cyclic Deformation Mechanisms in Haynes 188 Superalloy

The cyclic deformation behavior of a wrought cobalt-base superalloy, Haynes 188, has been investigated over a range of temperatures between 25 and 1000 C under isothermal and in-phase thermomechanical fatigue (TMF) conditions. Constant mechanical strain rates (epsilon-dot) of 10(exp -3)/s and 10(exp -4)/s were examined with a fully reversed strain range of 0.8%. Particular attention was given to the effects of dynamic strain aging (DSA) on the stress-strain response and low cycle fatigue life. A correlation between cyclic deformation behavior and microstructural substructure was made through detailed transmission electron microscopy. Although DSA was found to occur over a wide temperature range between approximately 300 and 750 C the microstructural characteristics and the deformation mechanisms responsible for DSA varied considerably and were dependent upon temperature. In general, the operation of DSA processes led to a maximum of the cyclic stress amplitude at 650 C and was accompanied by pronounced planar slip, relatively high dislocation density, and the generation of stacking faults. DSA was evidenced through a combination of phenomena, including serrated yielding, an inverse dependence of the maximum cyclic hardening with epsilon-dot, and an instantaneous inverse epsilon-dot sensitivity verified by specialized epsilon-dot -change tests. The TMF cyclic hardening behavior of the alloy appeared to be dictated by the substructural changes occuring at the maximum temperature in the TMF cycle.

Rao, K. Bhanu Sankara↗

DOE OSTI2023

Plastic homogeneity in nanoscale heterostructured binary and multicomponent metallic eutectics: An overview

Heterostructured materials comprised of relatively soft/hard disparate phases typically exhibit composite strengthening but lack plastic deformability at ambient temperatures. However, heterostructured systems comprised of nanoscale phases can simultaneously enhance yield strength and strain hardening, thereby promoting uniform distribution of plastic flow. In this review, the atomic-scale deformation mechanisms in model systems of eutectic alloys, Al-Al 2 Cu and Al-Si, refined to nanoscales via laser rapid solidification are discussed, and compared with literature on multi-component (high entropy) eutectics such as Ni-Al-Fe-based with Cr and/or Co additions. The nano-lamellar Al-Al 2 Cu structures exhibit unit defect mechanisms not reported in monolithic Al 2 Cu intermetallic: localized shear on {0 1 1} and shear-induced faults on {1 2 1} planes, constrained by closely-spaced dislocation arrays in Al confined by Al/Al 2 Cu interfaces. The unexpected plasticity mechanisms are enabled by slip continuity in nanoscale Al-Al 2 Cu eutectics associated with the orientation relationship and interface habit planes. In nano-fibrous Al-Si eutectic, tensile ductility at strength approaching 600 MPa is observed resulting from dislocation plasticity in the nano-Al channels and cracking in Si nanofibers. Molecular dynamics simulations show that Al dislocations easily cross-slip (screw) or climb (edge) along Al-Si interfaces, making slip transmission difficult. The propagation of nano-cracks is suppressed by surrounding strain hardening Al, retaining good ductility of the sample, in spite of lack of direct slip transmission. Finally, the critical unit mechanisms of slip transmission and interface-enabled plasticity observed in nanoscale eutectic binary systems can also explain the strength-ductility relationship in multi-component eutectics and homogeneously distributed plastic flow with increasing microstructural heterogeneity.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Phase-field modeling of dislocation–interstitial interactions

The mechanical behavior of body-centered cubic (BCC) materials can be dramatically affected by the presence of interstitial solute atoms. Here we present a new phase-field dislocation dynamics formulation to include the diffusion of interstitials. Short-range interactions are accounted for by a concentration-dependent lattice energy, and long-range interactions are accounted for by modifications to the elastic energy. The interstitial diffusion law introduces gradients that require methods for minimizing Gibbs oscillations, which is done via a modified Green’s function. The formulation is general to any solute-solvent system and is applied here to Nb-O as a model system, whose interstitial parameters are obtained from ab initio calculations. The effect of O on the core structures of Nb edge and screw dislocations is calculated. The diffusion of O to form interstitial atmospheres around dislocation cores is simulated, as well as the critical stresses required for dislocations to break away or cross slip from these atmospheres. Future applications of the method to simulate complex interstitial embrittlement mechanisms are discussed.

36 MATERIALS SCIENCE↗

NASA NTRS1993

Numerical modeling of physical vapor transport under microgravity conditions: Effect of thermal creep and stress

One of the most promising applications of microgravity (micro-g) environments is the manufacture of exotic and high-quality crystals in closed cylindrical ampoules using physical vapor transport (PVT) processes. The quality enhancements are believed to be due to the absence of buoyant convection in the weightless environment - resulting in diffusion-limited transport of the vapor. In a typical experiment, solid-phase sample material is initially contained at one end of the ampoule. The sample is made to sublime into the vapor phase and deposit onto the opposite end by maintaining the source at an elevated temperature with respect to the deposit. Identification of the physical factors governing both the rates and uniformity of crystal growth, and the optimization of the micro-g technology, will require an accurate modeling of the vapor transport within the ampoule. Previous micro-g modeling efforts have approached the problem from a 'classical' convective/diffusion formulation, in which convection is driven by the action of buoyancy on thermal and solutal density differences. The general conclusion of these works have been that in low gravity environments the effect of buoyancy on vapor transport is negligible, and vapor transport occurs in a diffusion-limited mode. However, it has been recently recognized than in the non-isothermal (and often low total pressure) conditions encountered in ampoules, the commonly-assumed no-slip boundary condition to the differential equations governing fluid motion can be grossly unrepresentative of the actual situation. Specifically, the temperature gradients can give rise to thermal creep flows at the ampoule side walls. In addition, temperature gradients in the vapor itself can, through the action of thermal stress, lead to bulk fluid convection.

Mackowski, Daniel W.↗