Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTIAL PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Temperature-dependent selective oxidation processes for Ni-5Cr and Ni-4Al

The selective oxidation of Ni-5Cr and Ni-4Al alloys is evaluated during high (800°C) and low (420°C) temperature exposures with the oxygen partial pressure moderated by a Ni/NiO powder buffer. Internal oxidation of Cr and Al is observed throughout the matrix and at grain boundaries at 800°C accompanied by the ejection of Ni onto the surface for both. At 420°C, matrix internal oxidation was eliminated and only Ni-4Al exhibited intergranular (IG) oxidation. Surprisingly, a protective surface oxide rapidly formed for Ni-5Cr blocking IG oxidation. This is contradictory to results in 330–360°C hydrogenated water environments where both alloys show IG oxidation.

Ni-based alloys, preferential intergranular oxidat↗

Chromia refractory brick with carbon treatment

The disclosure provides a refractory brick system comprising a chromia refractory brick for operation in the slagging environment of an air-cooled gasifier. The chromia refractory brick comprises a ceramically-bonded porous chromia refractory having a porosity greater than 9% and having carbon deposits residing within the pores. The brick may be further comprised of Al.sub.2O.sub.3. The air-cooled gasifier generates a liquefied slag in contact with the refractory brick and generally operates at temperatures between 1250.degree. C. and 1575.degree. C. and pressures between 300 psi to 1000 psi, with oxygen partial pressures generally between 10.sup.-4 and 10.sup.-10 atm. The refractory brick performs without substantial chromium carbide or chromium metal formation in the low oxygen partial pressure environment. The inclusion of carbon without chromium carbide formation provides for significant mitigation of slag penetration and significantly reduced refractory wear.

36 MATERIALS SCIENCE↗

Phase diagram features and solidification behaviour of CoCu{sub 2}O{sub 3} at elevated oxygen pressure

A unique behaviour of the phase CoCu{sub 2}O{sub 3} was found both from CALPHAD calculations and directional solidification experiments. For elevated oxygen partial pressure the solidification mode changed from double-peritectic to a congruent melting behaviour with respect to the metals (Cu, Co) and to the oxygen content. This transition predicted by the phase diagram calculations was confirmed by microstructure and phase analyses of samples solidified at oxygen pressures up to 60 bar. A DTA analysis has verified basic features of the phase diagram at normal pressures. - Graphical abstract: A unique behaviour of the phase CoCu{sub 2}O{sub 3} was found both from CALPHAD calculations and directional solidification experiments. For elevated oxygen partial pressure the solidification mode changed from double-peritectic (1 bar O{sub 2}; left figure) to a congruent melting behaviour with respect to the metals (Cu, Co) and to the oxygen content (80 bar O{sub 2}; right figure).

36 MATERIALS SCIENCE↗

On Gas Ingression of Hermetic Packages

In this paper, a closed-form mathematic equation that governs gas ingression of hermetic packages is derived from first principles and applied to moist air and water vapor ingression conditions. The equation models internal gas partial pressure change as a function of time, external conditions, and package characteristics. The equation provides the theoretical basis for direct comparisons of ingression behaviors of different gases into hermetic packages. Comparing the rates of internal air pressure increase due to air ingression and water vapor partial pressure buildup due to water vapor ingression, the authors theorize that vacuum decay may present a greater challenge to the performance of microelectromechanical systems (MEMS) devices within hermetic packages than that of water vapor content induced corrosion failures. Furthermore, this paper also examines gas ingression of hermetic enclosures with multiple layers of seals.

42 ENGINEERING↗

The Use of Spontaneous Raman Scattering for Hydrogen Leak Detection

A fiber optic probe has been built and demonstrated that utilizes back scattered spontaneous Raman spectroscopy to detect and identify gaseous species. The small probe, coupled to the laser and data acquisition equipment with optical fibers, has applications in gaseous leak detection and process monitoring. The probe design and data acquisition system are described. Raman scattering theory has been reviewed and the results of intensity calculations of hydrogen and nitrogen Raman scattering are given. Because the device is in its developmental stage, only preliminary experimental results are presented here. Intensity scans across the rotational-vibrational Raman lines of nitrogen and hydrogen are presented. Nitrogen at a partial pressure of 0.077 MPa was detected. Hydrogen at a partial pressure of 2 kPa approached the lower limit of detectability with the present apparatus. Potential instrument improvements that would allow more sensitive and rapid hydrogen detection are identified.

Degroot, Wim A.↗

Mass Flux of ZnSe by Physical Vapor Transport

Mass fluxes of ZnSe by physical vapor transport (PVT) were measured in the temperature range of 1050 to 1160 C using an in-situ dynamic technique. The starting materials were either baked out or distilled under vacuum to obtain near-congruently subliming compositions. Using an optical absorption technique Zn and Se, were found to be the dominant vapor species. Partial pressures of Zn and Se, over the starting materials at temperatures between 960 and 1140 C were obtained by measuring the optical densities of the vapor phase at the wavelengths of 2138, 3405, 3508, 3613, and 3792 A. The amount and composition of the residual gas inside the experimental ampoules were measured after the run using a total pressure gauge. For the first time, the experimentally determined partial pressures of Zn and Se, and the amount and composition of the residual gas were used in a one-dimensional diffusion limited analysis of the mass transport rates for a PVT system. Reasonable agreement between the experimental and theoretical results was observed.

Sha, Yi-Gao↗

Oxidation Behavior of GRCop-84 Copper Alloy Assessed

NASA's goal of safe, affordable space transportation calls for increased reliability and lifetimes of launch vehicles, and significant reductions of launch costs. The areas targeted for enhanced performance in the next generation of reusable launch vehicles include combustion chambers and nozzle ramps; therefore, the search is on for suitable liner materials for these components. GRCop-84 (Cu-8Cr-4Nb), an advanced copper alloy developed at the NASA Glenn Research Center in conjunction with Case Western Reserve University, is a candidate. The current liner of the Space Shuttle Main Engine is another copper alloy, NARloy-Z (Cu-3Ag-0.1Zr). It provides a benchmark against which to compare the properties of candidate successors. The thermomechanical properties of GRCop-84 have been shown to be superior, and its physical properties comparable, to those of NARloy-Z. However, environmental durability issues control longevity in this application: because copper oxide scales are not highly protective, most copper alloys are quickly consumed in oxygen environments at elevated temperatures. In consequence, NARloy-Z and most other copper alloys are prone to blanching, a degradation process that occurs through cycles of oxidation-reduction as the oxide is repeatedly formed and removed because of microscale fluctuations in the oxygen-hydrogen fuel systems of rocket engines. The Space Shuttle Main Engine lining typically degraded by blanching-induced hot spots that lead to surface roughening, pore formation, and coolant leakage. Therefore, resistance to oxidation and blanching are key requirements for second-generation reusable launch vehicle liners. The rocket engine ambient includes H2 (fuel) and H2O (combustion product) and is, hence, under reduced oxygen partial pressures. Accordingly, our studies were expanded to include oxygen partial pressures as low as 322 parts per million (ppm) at the temperatures likely to be experienced in service. A comparison of 10-hr weight gains of GRCop-84, NARloy-Z, and pure copper in 0.032, 2.2, and 100 percent oxygen from 550 to 750 C is shown. In 2.2 vol% and higher oxygen content, GRCop-84 oxidation was slower than that of NARloy-Z or Cu, but that advantage was lost or diminished in 322-ppm O2. Over longer (50-hr) exposures in 1.0 atm O2, however, the advantage of GRCop-84 increased significantly, its oxidation rate becoming approximately 10 times slower than those of Cu and NARloy-Z from 500 to 700 C. Weight gains were moderate and the kinetics parabolic for all three materials in 2.2 vol% and higher oxygen content; however, in 322-ppm O2, the scales were nonprotective below about 650 C, as reflected in linear kinetics and large weight gains. The superior oxidation resistance of GRCop-84 is likely related to the kinetics of extra oxygen consumption to form the additional oxides of Cr and Nb detected beneath the GRCop-84 oxide layer. While we continue to evaluate the blanching resistance of GRCop-84 in other tests, these oxidation results indicate that GRCop-84 is suitable as a reusable launch vehicle liner, and in applications where it is desired to use a copper alloy but without the risk of oxidative failure. Three bar charts comparing overall specific weight gains by each of the three materials studied. The top chart is for oxidation in 1.0 atm of oxygen, the middle is for 2.2% oxygen (balance argon), and the bottom is for 0.0322% oxygen. GRCop-84 outperforms the other two materials, showing the least weight gain in nearly all cases.

Thomas-Ogbuji, Linus U.↗

Resistance-Based Ceramic Ho123 Ionic Conductor for Oxygen Gas Sensing

Oxygen sensing properties of HoBa{sub 2}Cu{sub 3}O{sub 7-d}elta ceramic rods utilizing hot-spot phenomenon have been characterized. The rods were prepared from high purity oxides using the conventional solid-state reaction method. I-V characterization showed increase in output current with voltage before the appearance of the hot spot. After the appearance of the hot-spot, the output current strongly depended on oxygen partial pressure. The rod showed stable sensing characteristics with good electrical stability and reproducibility with higher sensitivity at low oxygen partial pressure. The sensing property is associated with the absorption of oxygen and dissociation into holes and oxide ions. Ho123 is more sensitive at pO{sub 2} below 20% compared to Er123 possibly due to differences in oxygen activation energy related to RE ionic radius.

36 MATERIALS SCIENCE↗

Growth of Cu{sub 2}O on Ga-doped ZnO and their interface energy alignment for thin film solar cells

Cu{sub 2}O thin films are deposited by direct current reactive magnetron sputtering on borofloat glass and indium tin oxide (ITO) coated glass at room temperature. The effect of oxygen partial pressure on the structures and properties of Cu{sub 2}O thin films are investigated. We show that oxygen partial pressure is a crucial parameter in achieving pure phases of CuO and Cu{sub 2}O. Based on this finding, we fabricate heterojunctions of p-type Cu{sub 2}O with n-type gallium doped ZnO (GZO) on ITO coated glass substrates by pulsed laser deposition for GZO thin films. The energy band alignment for thin films of Cu{sub 2}O/GZO on ITO glass is characterized using high-resolution x-ray photoelectron spectroscopy. The energy band alignment for the Cu{sub 2}O/GZO heterojunctions is determined to be type II with a valence band offset of 2.82 eV and shows negligible effects of variation with gallium doping. The higher conduction band of the Cu{sub 2}O relative to that of GZO in the obtained band alignment shows that the heterojunctions are suitable for solar cell application based on energy levels consideration.

36 MATERIALS SCIENCE↗

Digital Architecture for a Trace Gas Sensor Platform

A digital architecture has been implemented for a trace gas sensor platform, as a companion to standard analog control electronics, which accommodates optical absorption whose fractional absorbance equivalent would result in excess error if assumed to be linear. In cases where the absorption (1-transmission) is not equivalent to the fractional absorbance within a few percent error, it is necessary to accommodate the actual measured absorption while reporting the measured concentration of a target analyte with reasonable accuracy. This requires incorporation of programmable intelligence into the sensor platform so that flexible interpretation of the acquired data may be accomplished. Several different digital component architectures were tested and implemented. Commercial off-the-shelf digital electronics including data acquisition cards (DAQs), complex programmable logic devices (CPLDs), field-programmable gate arrays (FPGAs), and microcontrollers have been used to achieve the desired outcome. The most completely integrated architecture achieved during the project used the CPLD along with a microcontroller. The CPLD provides the initial digital demodulation of the raw sensor signal, and then communicates over a parallel communications interface with a microcontroller. The microcontroller analyzes the digital signal from the CPLD, and applies a non-linear correction obtained through extensive data analysis at the various relevant EVA operating pressures. The microcontroller then presents the quantitatively accurate carbon dioxide partial pressure regardless of optical density. This technique could extend the linear dynamic range of typical absorption spectrometers, particularly those whose low end noise equivalent absorbance is below one-part-in-100,000. In the EVA application, it allows introduction of a path-length-enhancing architecture whose optical interference effects are well understood and quantified without sacrificing the dynamic range that allows quantitative detection at the higher carbon dioxide partial pressures. The digital components are compact and allow reasonably complete integration with separately developed analog control electronics without sacrificing size, mass, or power draw.

Gonzales, Paula↗

Nanoscale duplex oxide growth during early stages of oxidation of Cu-Ni(100).

A combination of real-time in situ synchrotron x-ray diffraction and ex situ transmission electron microscopy is utilized to investigate the early stages of oxidation of Cu-Ni(100). Sequential formation of NiO and Cu{sub 2}O oxides was observed by increasing oxygen partial pressure, and the Cu{sub 2}O phase was identified to form preferentially on top of NiO nanoislands. The origin of this unexpected phenomenon is attributed to localized enrichment of Cu atoms accompanied with NiO growth, which thermodynamically drives the nanoscale Cu{sub 2}O/NiO duplex oxide growth.

43 PARTICLE ACCELERATORS↗

Electronic and magnetic tunability of Sr{sub 2}CrReO{sub 6} films by growth-mediated oxygen modulation

Highly ordered epitaxial films of ferrimagnetic semiconductor Sr{sub 2}CrReO{sub 6} (SCRO) have been fabricated by off-axis magnetron sputtering, and characterized as a function of the oxygen partial pressure. In this Letter, we report 18 000% modulation in electrical resistivity at T = 7K (60% at room temperature) from a 1% modulation in the oxygen partial pressure during film growth. The growth window was centered at peak saturation magnetization, which drops due to both increasing and decreasing oxygen growth pressure. The results suggest that n-type doping due to oxygen vacancies plays a dominant role in the electrical properties and modulation of Sr{sub 2}CrReO{sub 6} thin films.

36 MATERIALS SCIENCE↗

CdSxTe1-x Alloying in CdS/CdTe Solar Cells

A CdSxTe1-x layer forms by interdiffusion of CdS and CdTe during the fabrication of thin-film CdTe photovoltaic (PV) devices. The CdSxTe1-x layer is thought to be important because it relieves strain at the CdS/CdTe interface that would otherwise exist due to the 10% lattice mismatch between these two materials. Our previous work [1] has indicated that the electrical junction is located in thisinterdiffused CdSxTe1-x region. Further understanding, however, is essential to predict the role of this CdSxTe1-x layer in the operation of CdS/CdTe devices. In this study, CdSxTe1-x alloy films were deposited by RF magnetron sputtering and co-evaporation from CdTe and CdS sources. Both radio-frequency-magnetron-sputtered and co-evaporated CdSxTe1-x films of lower S content (x<0.3) have a cubiczincblende (ZB) structure akin to CdTe, while those of higher S content have a hexagonal wurtzite (WZ) structure like that of CdS. Films become less preferentially oriented as a result of a CdCl2 heat treatment at~400 degrees C for 5 min. Films sputtered in a 1% O2/Ar ambient are amorphous as deposited, but show CdTe ZB, CdS WZ, and CdTe oxide phases after a CdCl2 heat treatment (HT). Filmssputtered in O2 partial pressure have a much wider bandgap (BG) than expected. This may be explained by nanocrystalline size effects seen previously [2] for sputtered oxygenated CdS (CdS:O) films.

14 SOLAR ENERGY↗

Selective oxidation and oxidative dehydrogenation of hydrocarbons on bismuth vanadium molybdenum oxide

A systematic investigation of the oxidative dehydrogenation of propane to propene and 1- and 2-butene to 1,3-butadiene, and the selective oxidation of isobutene to methacrolein was carried out over Bi 1- x /3V 1- x Mo x O 4 ( x = 0-1) with the aim of defining the effects of catalyst and reactant composition on the reaction kinetics. This work has revealed that the reaction kinetics can differ significantly depending on the state of catalyst oxidation, which in turn depends on the catalyst composition and the reaction conditions. Under conditions where the catalyst is fully oxidized, the kinetics for the oxidation of propene to acrolein and isobutene to methacrolein, and the oxidative dehydrogenation of propane to propene, 1-butene and trans-2-butene to butadiene are very similar - first order in the partial pressure of the alkane or alkene and zero order in the partial pressure of oxygen. These observations, together with XANES and UV-Vis data, suggest that all these reactions proceed via a Mars van Krevelen mechanism involving oxygen atoms in the catalysts and that the rate-limiting step involves cleavage of the weakest C-H bond in the reactant. Consistent with these findings, the apparent activation energy and pre-exponential factor for both oxidative dehydrogenation and selective oxidation correlate with the dissociation energy of the weakest C-H bond in the reactant. As the reaction temperature is lowered, catalyst reoxidation can become rate-limiting, the transition to this regime depending on ease of catalyst reduction and effectiveness of the reacting hydrocarbons as a reducing agent. Here, a third regime is observed for isobutene oxidation at lower temperatures, in which the catalyst is more severely reduced and oxidation now proceeds via reaction of molecular oxygen, rather than catalyst lattice oxygen, with the reactant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Developing Accelerated Test Protocols and Tuning Microstructures of the Common Materials to Improve Robustness, Reliability, and Endurance of SOFC Cells

This work is built on our prior work where we found that phase transformation in praseodymium nickelates, e.g. Pr 2 NiO 4 (PNO) and (Pr 1-x Nd x ) 2 NiO 4 (PNNO), can be electrochemically driven, and is substantially faster when compared to thermal annealing studies. The first task aims at an attempt to further accelerate the phase transformation in the oxygen electrode by alternating the current input in the cells, which lead to the development of accelerated test protocols (ATPs). ATPs showed up to 60x faster phase transformation and up to 10x faster performance degradation in (Pr 0.50 Nd 0.50 ) 2 NiO 4 electrodes, when compared to long-term operation under constant current density. Furthermore, the phase stable Nd 2 NiO 4 and (La 0.6 Sr 0.4 )(Co 0.8 Fe 0.2 )O 3 (LSCF6482) electrodes were tested in full cells under ATPs, and showed up to 10x faster performance degradation within 1,100 hours in a comparison with long-term thermal annealing studies and electrochemical operation under constant current density. The second task aims at the quantification of the contributions of cell components to the total impedance of a solid oxide fuel cell (SOFC) using electrochemical impedance spectroscopy (EIS) and distribution of relaxation times (DRT). Specifically, the role of gas composition at both anode and cathode was systematically studied, aiming at deconvoluting, identifying and quantifying the contributions of different electrode processes. This was achieved by first tuning the partial pressure of H 2 at the anode and subsequently varying the partial pressure of O 2 at the cathode. The results suggest that, while DRT offers a viable way of deconvoluting different times distributions, additional attention is needed before assigning a peak to a specific electrode process due to the significant overlap of the contributions from the cathode and the anode. Density function theory studies show that both Pr-vacancies and O-defects play a key role on the activity and stability for nickelates towards oxygen reduction reaction. The resident O-interstitials and oxygen ions in the PrO layer form peroxide (O 2 2- ) nearby Pr vacancies. The O 2 2- limits oxygen-ion transport due to the required additional energy to break its O-O bond. We further calculated the formation and segregation energies for different Ln ions (La, Pr, Nd, Pm, Sm, Gd, Tb, Dy, and Ho) in PNO and CeO 2 (111) surfaces. In addition to Nd, Pm and La are suggested as potential dopants in PNO to enhance it stability without decomposition due to their more negative formation energies, lower diffusion energies, and positive separation energies.

01 COAL, LIGNITE, AND PEAT↗

Correlation of an optical system degradation with contamination on a critical surface

The loss of sensitivity of a radiantly cooled radiometer during space operation was investigated. A quartz crystal microbalance (QCM), mounted in the proximity of the instrument filter lens and held at its temperature, measured the contaminant at the location during a vacuum test. The temperature cycling of the lens and the QCM verified the contamination of the lens as the cause of the deterioration. Data on the instrument performance in space and in the chamber allowed estimation of the rate of contaminant accretion on the lens in space service. That rate was used to estimate the contaminant partial pressure. The nature of material was inferred by comparison of the partial pressures and the saturated vapor pressures of materials at the temperature of the contaminated surface. These data, in conjunction with data on fields of view of the lens, are used to identify the sources of contamination.

Scialdone, J. J.↗

Optimizing TaO{sub x} memristor performance and consistency within the reactive sputtering “forbidden region”

Standard deposition processes for depositing ReRAM oxides utilize mass flow of reactive gas to control stoichiometry and have difficulty depositing a precisely defined sub-stoichiometry within a “forbidden region” where film properties are discontinuous with mass flow. We show that by maintaining partial pressure within this discontinuous “forbidden region,” instead of by maintaining mass flow, we can optimize tantalum oxide device properties and reduce or eliminate the electroforming step. We also show that defining the partial pressure set point as a fraction of the “forbidden region” instead of as an absolute value can be used to improve wafer-to-wafer consistency with minimal recalibration efforts.

36 MATERIALS SCIENCE↗

Synthesis and electrochemical assessment of Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} ceramics and derived composite electrolytes

Highlights: • Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} prepared for the first time through solid state reaction. • High energy milling needed to assist the ceramic route. • Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} is oxide-ion conductor in air and n-type conductor at low pO{sub 2}. • Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} decomposes slightly when exposed to alkaline carbonates. • Composites based on Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} show standard electrical performance. - Abstract: Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} was prepared for the first time through high temperature (1600 °C for 5 h) solid state reaction, after high energy milling to enhance the mechano-chemical interaction of precursor oxides (CeO{sub 2} and Yb{sub 2}O{sub 3}). Single phase formation was confirmed by powder X-ray diffraction. Impedance spectroscopy data obtained under wide temperature (300–800 °C) and oxygen partial pressure (0.21 to about 10{sup −25} atm) ranges indicates that this material exhibits predominant oxide-ion conductivity under oxidizing conditions while n-type electronic conductivity prevails at low oxygen partial pressure. The mixed oxide shows modest ionic conductivity (1.1 × 10{sup −3} S cm{sup −1} at 800 °C) with activation energy of 1.3 eV in the 600–800 °C temperature range. When combined with molten carbonates (Li{sub 2}CO{sub 3} + Na{sub 2}CO{sub 3}, 1:1 molar ratio) to produce composite electrolytes, Ce{sub 0.5}Yb{sub 0.5}O{sub 1.75} slightly decomposed. However, the composite electrical performance is still acceptable and closely matches the conductivity of similar materials (>0.1 S cm{sup −1} immediately above 500 °C)

36 MATERIALS SCIENCE↗