Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ducted Fuel Injection vs. Conventional Diesel Combustion: Extending the Load Range in an Optical Engine with a Four-Orifice Fuel Injector

Ducted fuel injection (DFI) is a technique to attenuate soot formation in compression ignition engines relative to conventional diesel combustion (CDC). The concept is to inject fuel through a small tube inside the combustion chamber to reduce equivalence ratios in the autoignition zone relative to CDC. DFI has been studied at loads as high as 8.5 bar gross indicated mean effective pressure (IMEP g ) and as low as 2.5 bar IMEP g using a four-orifice fuel injector. Across previous studies, DFI has been shown to attenuate soot emissions, increase NO x emissions (at constant charge dilution), and slightly decrease fuel conversion efficiencies for most tested points. This study expands on the previous work by testing 1.1 bar IMEPg (low-load/idle) conditions and 10 bar IMEPg (higher-load) conditions with the same four-orifice fuel injector, as well as examining potential causes of the degradations in NO x emissions and fuel conversion efficiencies. DFI and CDC are directly compared at each operating point in the study. At the low-load condition, the intake charge dilution was swept to elucidate the soot and NO x performance of DFI. The low-load range is important because it is the target of impending, more-stringent emissions regulations, and DFI is shown to be a potentially effective approach for helping to meet these regulations. The results also indicate that DFI likely has slightly decreased fuel conversion efficiencies relative to CDC. We find that the increase in NO x emissions with DFI is likely due to longer charge gas residence times at higher temperatures, which arise from shorter combustion durations and advanced combustion phasing relative to CDC.

42 ENGINEERING↗
DOE OSTI2022

Noninvasive measurements of spin transport properties of an antiferromagnetic insulator

Antiferromagnetic insulators (AFIs) are of substantial interest because of their potential in the development of next-generation spintronic devices. One major effort in this emerging field is to harness AFIs for long-range spin information communication and storage. Here, we report a noninvasive method to optically access the intrinsic spin transport properties of an archetypical AFI α-Fe 2 O 3 via nitrogen-vacancy (NV) quantum spin sensors. By NV relaxometry measurements, we successfully detect the frequency-dependent dynamic fluctuations of the spin density of α-Fe 2 O 3 along the Néel order parameter, from which an intrinsic spin diffusion constant of α-Fe 2 O 3 is experimentally measured in the absence of external spin biases. Our results highlight the significant opportunity offered by NV centers in diagnosing the underlying spin transport properties in a broad range of high-frequency magnetic materials such as two-dimensional magnets, spin liquids, and magnetic Weyl semimetals, which are challenging to access by the conventional measurement techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Optical conductivity of multi-Weyl node semimetals due to electromagnetic and axial pseudogauge fields

Here, we compute the optical conductivity of a multi-Weyl semimetal in the presence of electromagnetic and axial fields. In the first part of the paper we use a U(1) gauge field to compute the current of a multi-Weyl semimetal. The current is used in the computation of the optical conductivity within the Kubo-Matsubara formalism. We consider a multi-Weyl semimetal with two nodal points in the z-direction. The multi-Weyl semimetal has a width D in the transverse direction which is smaller than the length L in the longitudinal direction. Due to the width D we replace the model by a sum of transverse modes in 1+1 dimensions. We then regularize the model in 1+1 dimensions. The nodal points are responsible for a constant axial field and a static anomalous Hall effect. In the second part we study the effect of dynamic axial fields. An elastic deformation couples to the two electronic chiralities, and represents the axial pseudogauge field $\vec{a}$ 5 . As a consequence, the system is excited by two kinds of field, the electromagnetic one and the axial srain field. For a Weyl system this is represented by the triangle diagram, which is responsible for the anomalous Hall effect. We can obtain the anomalous Hall effect also by a chiral transformation in 1+1 dimensions using regularization. The chiral transformation modifies the path integration measure and is the source of the induced anomalous Hall effect. The latter is controlled by a combination of strain waves and electromagnetic fields.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Ultrathin high- κ antimony oxide single crystals

Ultrathin oxides have been reported to possess excellent properties in electronic, magnetic, optical, and catalytic fields. However, the current and primary approaches toward the preparation of ultrathin oxides are only applicable to amorphous or polycrystalline oxide nanosheets or films. Here, we successfully synthesize high-quality ultrathin antimony oxide single crystals via a substrate-buffer-controlled chemical vapor deposition strategy. The as-obtained ultrathin antimony oxide single crystals exhibit high dielectric constant (~100) and large breakdown voltage (~5.7 GVm -1 ). Such a strategy can also be utilized to fabricate other ultrathin oxides, opening up an avenue in broadening the applicaitons of ultrathin oxides in many emerging fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Radiative dynamics and delayed emission in pure and doped InP/ZnSe/ZnS quantum dots

We have used time-correlated single photon counting to elucidate the radiative dynamics of InP/ZnSe/ZnS core/shell/shell quantum dots (QDs) that differ in the amount and distribution of excess indium. Stoichiometric QDs having an In:P atom ratio very near unity exhibit simple luminescence kinetics. The photoluminescence (PL) rises with the 40 ps instrument response function and exhibits a decay that is close to a single exponential with a time constant that decreases from 32 to 28 ns with increasing shell thickness. QDs having excess indium (In:P ratio of 1.15–1.63) show a significant component of a slower rise time assigned to transient population of indium-based hole traps in the ZnSe shell. They also have a slower PL decay, attributed to an equilibrium between these traps, which are optically dark, and the emissive valence-band state. This results in a radiative lifetime that increases from 32 to 48 ns with increasing shell thickness. Different treatments of the InP cores prior to shell deposition result in different core/shell interfaces as indicated by resonance Raman spectroscopy, as well as differences in the amplitude and timescale of the slow PL rise and the PL decay time. These are interpreted in terms of different radial distributions of the indium-based hole traps, which can be related to differences in the interfacial lattice strain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Oxidation in laser-generated metal plumes

The temporal evolution of atoms and molecules in a laser-produced plasma was investigated using optical emission spectroscopy for several metal targets (i.e., Al, Ti, Fe, Zr, Nb, and Ta). Plasmas from metal targets were generated by focusing 1064 nm, 6 ns pulses from an Nd:YAG laser. Gas-phase oxidation/plasma chemistry was initiated by adding O2 (partial pressures up to ≈20%) to an N2 environment where the total background pressure was kept at a constant 1 atmosphere. Temporally resolved emission spectral features were used to track the gas-phase oxidation. The dynamics of atomic and molecular species were monitored using space-resolved time-of-flight emission spectroscopy. Our results highlight that the partial pressure of O2 strongly influences spectral features and molecular formation in laser-produced plasmas. Atoms and molecules co-exist in plasmas, although with different temporal histories depending on the target material due to differences in thermo- and plasma chemical reactions occurring in the plume.

Kautz, Elizabeth J. (ORCID:0000000263389223)↗
DOE OSTI2020

Understanding the depletion of electrons in dusty plasmas at atmospheric pressure

The nucleation and growth of NPs in the gas phase using atmospheric-pressure plasma systems is an important approach to synthesizing novel dimensionally-controlled materials. In this paper, we investigated the effect of the NPs on a typical type of continuous-flow, substrate-free plasma at atmospheric pressure to understand their potential contribution to electron density changes. A tandem plasma system was set up consisting of one plasma reactor that produced carbonaceous NPs from mixtures of argon and hexane, and another identical plasma reactor where the as-grown particles were injected and non-intrusive electrical and optical measurements were performed. The electron densities obtained from conductivity measurements and a plasma fluid model were found to decrease in the presence of NPs. However, control experiments revealed that the main source of the electron depletion was residual vapor or reaction byproducts in the form of molecular species or nanoclusters and not the particles themselves. These results were validated by constant number Monte Carlo simulations which showed that at the experimentally-measured conditions, the NPs were not of sufficiently high enough concentration to reduce the electron density; however, if molecules or clusters are ionizable, they remain in sufficient concentration to deplete electron densities. Our study shows that at atmospheric pressure, because of their typically larger electron density values, particle-producing plasmas are distinct from those at low pressure, and nanoparticle formation does not have the same impact while molecular-scale species may be a more important consideration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Finding Multiply Lensed and Binary Quasars in the DESI Legacy Imaging Surveys

The time delay between multiple images of strongly lensed quasars is a powerful tool for measuring the Hubble constant ( H 0 ). To achieve H 0 measurements with higher precision and accuracy using the time delay, it is crucial to expand the sample of lensed quasars. We conduct a search for strongly lensed quasars in the Dark Energy Spectroscopic Instrument (DESI) Legacy Imaging Surveys. The DESI Legacy Surveys comprise 19,000 deg 2 of the extragalactic sky observed in three optical bands ( g , r , and z ), making it well suited for the discovery of new strongly lensed quasars. We apply an autocorrelation algorithm to ~5 million objects classified as quasars in the DESI Quasar Sample. These systems are visually inspected and ranked. Here, we present 436 new multiply lensed and binary quasar candidates, 65 of which have redshifts from Sloan Digital Sky Survey Data Release 16. We provide redshifts for an additional 18 candidates from the SuperNova Integral Field Spectrograph.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Fiber-optic bolometer with low detection limit fabricated using thermal release tape and precise laser heating

Fiber-optic bolometers (FOBs) based on a fiber-tipped silicon Fabry–Perot (FP) interferometric temperature sensor and a gold disk absorber have been shown to be an attractive alternative to conventional resistive bolometers for plasma radiation measurement in fusion devices. Either a high-finesse FP or a low-finesse FP can be used, each with trade-offs between noise performance and fabrication complexity. In this paper, we present an FOB design that overcomes these limitations by combining a low-finesse long silicon FP cavity with a large gold disk absorber to achieve enhanced sensitivity and noise performance without increasing the fabrication complexity and the time constant. We also demonstrated a fabrication method for the sensor head facilitated by thermal release tape and precise laser heating. Our FOB demonstrates a temperature resolution of 0.08 mK, a cooling time constant of 230 ms, and a noise equivalent power density of 0.015 W m −2 . This represents an eightfold improvement over previous high-finesse FOBs and 26-fold improvement over previous low-finesse FOBs with similar demodulation bandwidths and similar cooling time constants.

Fabry–Perot interferometer↗
DOE OSTI2021

Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films

We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A machine learning approach to determine the elastic properties of printed fiber-reinforced polymers

This work focuses on the simultaneous determination of the elastic constants and the fiber orientation state for a short fiber-reinforced polymer composite by performing a minimum of experimental tests. Here we introduce a methodology that enables the inverse determination of fiber orientation state and the in-situ polymer properties by performing tensile tests at the composite coupon level. We demonstrate the approach for the extrusion deposition additive manufacturing (EDAM) process to illustrate one application of the methodology, but the development is such that it can be applied to short fiber-reinforced polymer (SFRP) systems processed via other methods. Currently, developing composites additive manufacturing digital twins require extensive material characterization. In particular, the mechanical characterization of the orthotropic elastic properties of a composite involves extensive sample preparation and testing, therefore the elasticity tensor is generally populated using a micromechanics model. This, however, requires measuring the fiber orientation state in addition to knowing the constituent material properties. Experimentally measuring the fiber orientation state can be tedious and time consuming. Further, optical methods are limited to resolving the orientation of cylindrical fibers or cluster of non-cylindrical fibers, and computed tomography (CT) methods scan regions of volume that are much smaller than a full printed bead. Therefore, we propose a methodology, accelerated by machine learning, to identify the anisotropic mechanical properties and fiber orientation state at the same time. Early results show that inference of the fiber orientation and composite properties is possible with as few as three tensile tests. Our results show that a combination of the choice of the micromechanics model and reliable set of experiments can yield the nine elastic constants, as well as, the fiber orientation state.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Assessment of empirical interatomic potential to predict thermal conductivity in ThO 2 and UO 2

Computing vibrational properties of crystals in the presence of complex defects often necessitates the use of (semi-)empirical potentials, which are typically not well characterized for perfect crystals. In this study we explore the efficacy of a commonly used embedded-atomempirical interatomic potential for the U x Th 1- x O 2 system, to compute phonon dispersion, lifetime, and branch specific thermal conductivity. Our approach for ThO 2 involves using lattice dynamics and the linearized Boltzmann transport equation to calculate phonon transport properties based on second and third order force constants derived from the empirical potential and from first-principles calculations. For UO 2 , to circumvent the accuracy issues associated with first-principles treatments of strong electronic correlations, we compare results derived from the empirical interatomic potential to previous experimental results. It is found that the empirical potential can reasonably capture the dispersion of acoustic branches, but exhibits significant discrepancies for the optical branches, leading to overestimation of phonon lifetime and thermal conductivity. The branch specific conductivity also differs significantly with either first-principles based results (ThO 2 ) or experimental measurements (UO 2 ). These findings suggest that the empirical potential needs to be further optimized for robust prediction of thermal conductivity both in perfect crystals and in the presence of complex defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Fluid Flow Observations of The Spray Near-Field Using High-Speed X-Ray Imaging

Sprays are important to may industrial processes, but the near-field region where spray formation takes place is difficult to visualize and characterize through visible light imaging because this region is typically optically dense. X-ray imaging is one technique that can penetrate this optically dense region and provide unique observations of the spray formation process. This study uses high-speed white beam X-ray imaging conducted at the Advanced Photon Source to capture spray formation dynamics from a canonical airblast atomizer. In this work, a range of momentum flux ratios are visualized by varying the gas flow rate while the liquid flow rate is held constant. The use of X-rays show overlapping flow structures including bags, ligaments, mushrooms, and webs. Air bubbles are captured within the liquid regions, and a very dynamic crown forms at the liquid needle exit at higher momentum flux ratios. Finally, at the highest momentum flux ratios, air bubbles and liquid droplets are observed migrating upstream in the center of the crown, and this motion is attributed to a toroidal recirculation cell at the nozzle exit.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Quantum optical classifier with superexponential speedup

Abstract Classification is a central task in deep learning algorithms. Usually, images are first captured and then processed by a sequence of operations, of which the artificial neuron represents one of the fundamental units. This paradigm requires significant resources that scale (at least) linearly in the image resolution, both in terms of photons and computational operations. Here, we present a quantum optical pattern recognition method for binary classification tasks. It classifies objects without reconstructing their images, using the rate of two-photon coincidences at the output of a Hong-Ou-Mandel interferometer, where both the input and the classifier parameters are encoded into single-photon states. Our method exhibits the behaviour of a classical neuron of unit depth. Once trained, it shows a constant $${{\mathcal{O}}}(1)$$ O ( 1 ) complexity in the number of computational operations and photons required by a single classification. This is a superexponential advantage over a classical artificial neuron.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

General algorithm for characterization of donor-acceptor pair recombination processes in solid-state materials

Radiative recombination processes can occur in solid-state systems through the pairing of donor and acceptor defects of the lattice. Recently, donor-acceptor pairs (DAP) have been proposed as promising candidates for quantum applications, and their signature has been observed in emerging low-dimensional materials. Therefore, the identification of such processes is gaining interest and requires methods to efficiently and reliably characterize them. Here, we introduce a general algorithm to identify DAP processes starting from the experimental photoluminescence (PL) emission spectrum and basic material parameters, including the lattice structure and dielectric constant. The algorithm recognizes possible DAP transitions from the emission pattern in the spectrum and returns the characteristic energy of the DAP transition and the separation between the donor and acceptor sites. By testing the algorithm on the photoluminescence spectrum of hexagonal boron nitride (hBN), we show that our method is robust against experimental errors and adds new capabilities to the investigation toolbox of semiconductors and their optical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Measuring the Hubble Constant with Dark Neutron Star–Black Hole Mergers

Abstract Detection of gravitational waves (GWs) from neutron star-black hole (NSBH) standard sirens provides local measurements of the Hubble constant (H 0 ), regardless of the detection of an electromagnetic (EM) counterpart, given that matter effects can be exploited to break the redshift degeneracy of the GW waveforms. The distinctive merger morphology and the high-redshift detectability of tidally disrupted NSBH make them promising candidates for this method. Also, the detection prospects of an EM counterpart for these systems will be limited toz< 0.8 in the optical, in the era of future GW detectors. Using recent constraints on the equation of state of NSs from multi-messenger observations of NICER and LIGO/Virgo/KAGRA, we show the prospects of measuringH 0 solely from GW observation of NSBH systems, achievable by the Einstein telescope (ET) and Cosmic Explorer (CE) detectors. We first analyze individual events to quantify the effect of high-frequency (≥500 Hz) tidal distortions on the inference of NS tidal deformability parameter (Λ) and hence onH 0 . We find that disruptive mergers can constrain Λ up to  ( 60 % ) more precisely than nondisruptive ones. However, this precision is not sufficient to place stringent constraints on theH 0 from individual events. By performing Bayesian analysis on simulated NSBH data (up toN= 100 events, corresponding to a day of observation) in the ET+CE detectors, we find that NSBH systems enable unbiased 4%–13% precision on the estimate ofH 0 (68% credible interval). This is a similar measurement precision found in studies analyzing NSBH mergers with EM counterparts in the LVKC O5 era.

Astronomy & Astrophysics↗
DOE OSTI2024

A method for generating quantitative vapor-phase infrared spectra of solids: results for phenol, camphor, menthol, syringol, dicyclopentadiene and naphthalene

Here, a method is presented to generate quantitative vapor-phase infrared spectra from substances that naturally occur as solids with moderate volatility. The solid is gravimetrically dissolved into a solvent that has few infrared spectral features, typically CS 2 and CCl 4 separately. The solution is flowed at a constant rate from a linearly pumped syringe into a metered stream of nitrogen carrier gas regulated by a mass flow controller. The analyte/solvent mix is flash vaporized by volatilizing the solution across a heated stainless-steel surface as it emanates from the syringe tip. The N 2 gas-solution mixture is flowed into a long-path White cell thermostatted at a desired temperature, the long optical path compensating for the modest analyte mixing ratio. A composite spectrum is generated from typically ten or more 760-Torr pressure-broadened spectra over the 600 to 6500 cm -1 spectral range at 0.1 cm -1 spectral resolution. The solid analytes reported here using this novel technique include dicyclopentadiene, menthol, syringol, phenol, camphor, and naphthalene.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗