Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NSLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Longitudinal Beam Parameter Tolerance of NSLS-II

Similar to the transverse phase space, the beam parameters in the longitudinal phase space must also be monitored and controlled. In the longitudinal phase space the fundamental parameters are: bunch arrival time(or the corresponding RF phase), average momentum, bunch length, and momentum spread. These parameters are usually perturbed by the various noises in a real machine. The noises could excite longitudinal bunch motion, seen by the users as timing jitter, intensity and wavelength variation, and transverse position shift et al. The longitudinal oscillations also cause longitudinal emittance growth, therefore lengthen the bunch and increase the momentum spread, and eventually decrease the brightness. As a rule of thumb for the tolerances, either transverse or longitudinal, the perturbation caused by the noises should not result in a decrease of brightness by more than 10%.

36 MATERIALS SCIENCE↗

Study Results and Plans for Future Improvement of the NSLS-II FOFB System

Currently, the fast orbit feedback (FOFB) system correct the transverse orbit in both planes via air coil magnets installed over low conductivity sections of vacuum chamber (stainless steel bellows) with a fast acquisition (FA) that samples at 10kHz. Bandwidth of a few kHz has been achieved (power-supply + corrector + vacuum chamber) for the purpose that the FOFB bandwidth limitation is not anymore limited by the correctors. The bandwidths of the FOFB system in both planes have been experimentally characterized in the open-loop condition via sinwave excitation method. They are significantly lower than the measurements (2.5kHz in x) done by Weixing Chen et al when the control system was largely bypassed, only from PSI to fast correctors, final to BPM. The estimated dI/dt as a function of the frequency from the beam noise spectrum has been compared to the slew rate of the power supply. The most recent study evidences: after the optimization of fast corrector compensation circuit, the power supply system along shows the 3dB bandwidth of 5.6kHz in the horizontal plane and 3.5kHz in the vertical plane. Preliminary beam studies indicate the potential increase of the system bandwidth and the gain within the FOFB bandwidth. Finally, the plan for combing the FOFB and SOFB systems to correct down to DC has been discussed.

36 MATERIALS SCIENCE↗

NSLS-II FOFB Performance Improvement in 2019

APS-U declared that they have achieved 700 Hz to 1kHz fast orbit feedback (FOFB) closeloop bandwidth in their two-section test setup. Before this, most light sources have been running FOFB with 100-200Hz bandwidth. Table 1 shows the information of bandwidths and sampling rates of various Synchrotron facilities.

36 MATERIALS SCIENCE↗

Feasibility Study of NSLS-II Sextupole BBA Measurement

In storage ring light sources, beam-based alignment (BBA) which adjusts the BPM centers to the quadrupole magnet centers is a common practice to maintain the machine performance. For more reliable and convenient BBA process, in the design of the storage ring, BPMs are located as close as possible to the quadrupoles. The most common method is scanning the position of the beam at the BPM (equivalently at the adjacent quadrupole) and find the position where the quadrupole strength change does not give change in the closed orbit. In the simulation of the feasibility test, we choose parameters, tune, orbit and phase advance and measure their variations depending on the sextupole offsets. Also, together with the real configuration of family, we simulate the individual power supply case for the comparisons. In this note, the simulation processes and the results are presented.

43 PARTICLE ACCELERATORS↗

SOURCE OF MICROBUNCHING AT BNL NSLS SOURCE DEVELOPMENT LABORATORY

We report experimental studies of the origins of electron beam microbunching instability at BNL Source Development Laboratory (SDL). We eliminated laser-induced microbunching by utilizing an ultra-short photocathode laser. The measurements of the resulting electron beam led us to conclude that, at SDL, microbunching arising from shot noise is not amplified to any significant level. Our results demonstrated that the only source of microbunching instability at SDL is the longitudinal modulation of the photocathode laser pulse. Our work shows that assuring a longitudinally smoothed photocathode laser pulse allows mitigating microbunching instability at a typical FEL injector with a moderate microbunching gain. In this paper we investigated the source of microbunching instability at the SDL. To distinguish microbunching induced by shot noise from that arising from the longitudinal modulation of the photocathode laser, we studied the beam created by a very short laser pulse, thus eliminating the possibility of laser-induced microbunching. While the measured energy spectra of compressed beam did reveal severe longitudinal fragmentation, an analysis of the beam dynamics proved this to be due to self-fields acting on a beam with an initially smooth longitudinal profile, and not due to microbunching instability. Such fragmentation only was possible with the very short bunch chosen for these studies, and is absent in routine SDL operations. Our experiment shows that in the absence of the initial laser-induced beam modulation, microbunching instability at the SDL is not observed, and must be well below the levels that would limit the FEL performance. This result agrees with assumption of previous SDL studies that (when present under different machine conditions) microbunching instability at the SDL was laser-induced. Microbunching instability gain at the SDL is moderate. This is mainly because the SDL utilizes a single stage bunch compressor as well as due to the small compression ratio. Since the design of the SDL injector is typical of the majority of FEL injectors, our experiment proves that one possible way to control microbunching instability in such machines (that by design have a moderate microbunching gain) is to maintain a sufficiently smooth longitudinal profile of the photo-cathode laser. We note that the general principles for designing a machine with a moderate microbunching instability gain are presented in [12]. In conclusion, our experiment demonstrates that microbunching instability can be eliminated from a typical FEL injector with single stage bunch compressor (and operating without a laser heater) as long as the photocathode laser is longitudinally smooth. For machines with multi-stage bunch compressors, our results offer an important benchmark to establish a minimal laser heater power for instability-free operation.

43 PARTICLE ACCELERATORS↗

Remote Access to the PXRR Macromolecular Crystallography Facilities at the NSLS

The most recent surge of innovations that have simplified and streamlined the process of determining macromolecular structures by crystallography owes much to the efforts of the structural genomics community. However, this was only the last step in a long evolution that saw the metamorphosis of crystallography from an heroic effort that involved years of dedication and skill into a straightforward measurement that is occasionally almost trivial. Many of the steps in this remarkable odyssey involved reducing the physical labor that is demanded of experimenters in the field. Other steps reduced the technical expertise required for conducting those experiments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

PHYSICS RESULTS OF THE NSLS-II LINAC FRONT END TEST STAND

The Linac Front End Test Stand (LFETS) was installed at the Source Development Laboratory (SDL) in the fall of 2011 in order to test the Linac Front End. The goal of these tests was to test the electron source against the specifications of the linac. In this report, we discuss the results of these measurements and the effect on linac performance.

43 PARTICLE ACCELERATORS↗

CONTROL OF NONLINEAR DYNAMICS BY ACTIVE AND PASSIVE METHODS FOR THE NSLS-II INSERTION DEVICES

Nonlinear effects from insertion devices are potentially a limiting factor for the electron beam quality of modern ring-based light sources, i.e., the on and off-dynamical aperture, leading to reduced injection efficiency and beam lifetime. These effects can be modelled by e.g. kick maps ({approx}1/{gamma}{sup 2}) and controlled by e.g. first-order thin or thick magnetic kicks introduced by 'magic fingers,' 'L-shims,' or 'current strips'. However, due to physical or technological constraints, these corrections are typically only partial. Therefore, a precise model is needed to correctly minimize the residual nonlinear effects for the entire system. We outline a systematic method for integrated design and rapid prototyping based on evaluation of the 3D magnetic field and control of the local trajectory with RADIA, and particle tracking with Tracy-3 for validation. The optimal geometry for the compensating magnetic fields is determined from the results of these simulations using a combination of linear algebra and genetic optimization.

43 PARTICLE ACCELERATORS↗