Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Morphology optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Demonstration of MgCr 2– x Mn x O 4 Spinel Oxide Cathodes in High-Voltage Mg Batteries

Solid-solution oxide spinels with high redox voltages and facile Mg 2+ mobility have been identified as promising candidates for practical, high-voltage cathodes in Mg batteries. In this work, we discuss the development of MgCr 2-x Mn x O 4 [x = 0.5, 1, 1.2] solid-solution spinel oxides as a cathode material and their electrochemical performance paired with an Mg anode in a full cell. This work presents the first demonstration of full cells with these materials. Mg-Cr-Mn spinel oxides with varying Cr and Mn contents were synthesized using alternative synthetic routes for optimal electrochemical performance. High-resolution synchrotron powder X-ray diffraction (PXRD), solid-state nuclear magnetic resonance (NMR) spectroscopy, and electron microscopy showed that these different synthetic routes resulted in changes in structures and particle morphologies, which in turn affect the electrochemical performance. Particularly, the urea coprecipitation synthetic route resulted in high-surface-area particles that enabled lower overpotentials and increased discharge capacity. The high surface area also resulted in expedited structural degradation caused by the irreversible migration of Mg 2+ into normally vacant 16c sites in the spinel lattice. This structural degradation was lessened by using a hydrosauna-urea synthesis method, which decreased the Mg/Mn inversion ratio while retaining high-surface-area particles with good cycling performance. Furthermore, our findings highlight the necessity for high surface area or nanostructured spinel oxide cathodes with minimized Mg-Mn inversion to enable spinel oxide cathodes in Mg full cells.

Mg anode↗
DOE OSTI2021

Quantifying particle-scale 3D granular dynamics during rapid compaction from time-resolved in situ 2D x-ray images

Understanding the particle-scale dynamics of granular materials during rapid compaction and flow is of fundamental importance for manufacturing, planetary science, geology, and defense applications. Time-resolved 2D radiography and static 3D x-ray tomography are powerful in situ tools for studying particle-scale dynamics but provide detail only in 2D or with significant time-scale limitations, respectively. Here, we introduce a new method that uses 2D in situ x-ray imaging for determining time-resolved 3D particle-scale dynamics in rapidly compressed granular materials. The method employs initial particle packing structures obtained from x-ray tomography, a 2D x-ray image generation algorithm, and an optimization algorithm. We first describe and validate the method using finite element simulations. Furthermore, we then apply the technique to x-ray phase-contrast images obtained during rapid compaction of granular materials with varying particle morphology and sample thickness. The depth-resolved particle-scale dynamics reveal complex velocity and porosity fields evolving heterogeneously along and perpendicular to the compaction direction. We characterize these features, their fluctuations near the compaction front, and the compaction front thickness. Our technique can be applied to understanding granular dynamics during rapid compaction events, and rearrangements during slower, but non-quasi-static, flows.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spall strength of additively repaired 304L stainless steel

Additive manufacturing has the potential to repair damaged parts, but the performance of additive materials under high strain rate loading is still uncertain—especially with the added complexity of an interface with an existing wrought material. In this work, 304L stainless steel samples were intentionally damaged and then repaired with wire-fed laser additive manufacturing. The samples were subjected to shock loading to generate incipient spall. Velocimetry and post-mortem metallography results show that when the additive repair process parameters are optimized to reduce porosity and match the equation of state of the original material, the influence of the repair region on the shock propagation is negligible. In conclusion, the free-surface velocity profile and internal damage morphology of the repaired sample are shown to be practically identical to the pristine material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Photoprotection during iron deficiency is mediated by the bHLH transcription factors PYE and ILR3

Iron deficiency has many adverse effects on photosynthesis, which is not surprising given that 90% of foliar iron is found in the chloroplast. Although many iron-sparing mechanisms have been documented, a mechanistic understanding of how chloroplasts adapt to iron deficiency was lacking. Here, we show that the bHLH transcription factors ILR3 and PYE are required for photoprotection during iron deficiency. Changes in chloroplast morphology under the control of these transcription factors prevents the production of harmful reactive oxygen species and allows for repair of photosystem II. Understanding how plants adapt the photosynthetic machinery during iron deficiency may allow us to optimize plant growth in soils where iron is not bioavailable.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Support Vector Machines for Classification of Direct Energy Deposition Standoff Distance for Improved Process Control

A critical factor in the implementation of direct energy deposition is the ability to maintain the standoff distance between the nozzle and the build surface, as this influences powder capture efficiency and overall part quality. Due to process-related variations, layer height may vary, causing unintended variation in standoff distance and poor build quality. While prior work has utilized contact probing to qualify standoff distance during processing, in situ methods for qualification of standoff distance are of major interest. The present work seeks to understand efficacy of image-based methods for classifying standoff distance variation in real-time using support vector machines (SVMs). It was hypothesized that the size of the melt pool and the amount of spatter will have significant correlations with deviations in the standoff distance; thus, SVMs were used on a dataset that is comprised of morphological features of melt pool size and image entropy. The SVM model was used to classify melt pool images into categories according to standoff distance variation from nominal. K-folds cross validation was used to find the optimal hyperparameters for the SVM model. To understand the impact of the selected features on the classification performance and inference speed, multiple models were trained with differing numbers of included features. Results for classification score, inference time, and image preprocessing/feature extraction from these data are reported. The present results show that the SVM model was able to predict the standoff distance classification with an accuracy of 97 percent and a speed of 0.122 s per image, making it a viable solution for real-time control of standoff distance.

Klesmith, Zoe↗
DOE OSTI2022

ACORN Review: NPK fertilizer use in loblolly pine plantations: Who are we really feeding?

Optimizing loblolly pine (Pinus taeda L.) productivity using fertilizers and various site management practices has been a goal of foresters for decades. Nitrogen (N), phosphorus (P), and potassium (K) are the three most operationally applied fertilizers to loblolly pine silviculture and are of primary importance to their total productivity. Fertilizer recommendations for N, P, and K in loblolly pine are primarily made on abiotic factors such as site and soil characteristics, while the biological factors controlling nutrient uptake are typically overlooked in the production and optimization of these stands. Arguably the most important of these biological factors are the diverse ectomycorrhizal fungal (ECM) communities that colonize the fine roots of almost all loblolly pine trees. The mantle formed by ECM fungi on short-root tips presents a barrier for direct apoplastic uptake of N, P, and K from soil solution by pine roots. In well-colonized roots, the tree is dependent on symplastic fungal transport of N, P, and K foraged from the soil by the extraradical hyphal network. This raises the question: Who are we really feeding if the ECM fungi are the ones assimilating most of the tree's total nutritional requirements? Considering multiple species of ECM fungi can inhabit a single root system, many questions remain regarding the drivers of colonization, why some species are more efficient at taking up and exchanging nutrients with their hosts than others, and why certain fertilizers directly affect the morphology of ECM growth. The purposes of this review here are (1) to explore how the most commonly commercially applied macronutrients, N, P, and K, affect the relationship between loblolly pine and ECM communities, and (2) to propose future directions to investigate, preserve, and manipulate these interactions in pine plantations to optimize productivity.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Co-Based superalloy morphology evolution: A phase field study based on experimental thermodynamic and kinetic data

Cobalt-based superalloys with two phase $\gamma$/$\gamma '$ microstructures offer great promise as candidates for next-generation high-temperature alloys for applications, such as turbine blades. It is essential to understand the thermodynamic and kinetic factors that influence the microstructural evolution of these alloys in order to optimize the alloy compositions and processing steps with a goal to improve their coarsening, creep and rafting behavior. We are using a continuum phase field approach to study the diffusion process and to predict the equilibrium shapes of Co-Al-W $\gamma '$ precipitates. In order to obtain quantitatively predictive capabilities, we extract chemical free energies for the $\gamma$/$\gamma '$ phases based on CALculation of PHAse Diagrams (CALPHAD) thermodynamic data and diffusion mobilities for Co alloys based on CALPHAD kinetic data. We also use experimental or first-principles data for other quantities, such as misfit strain and interface information, for the parameterization of our model. A particular focus of our study is to understand how different energy balances, misfit strain and kinetics affect the coarsening and rafting behavior of $\gamma '$ precipitates, and the sensitivity of the final precipitate shape to materials parameters. Here, we find that the equilibrium shape of the precipitate results from a delicate competition between chemical, interfacial, and elastic energies, and it is very sensitive to changes in model parameters. Here, we examine how modeling input parameters affect the equilibrium shape of precipitates and relate these parameters to experimentally available values.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mesocrystallizing Nanograins for Enhanced Li + Storage

Morphology and crystallinity of electrode materials have a major effect on their charge carrier storage properties when applied in rechargeable batteries. While nanosizing electrode particles (with larger surface area) and maintaining electrode integrity are both good for performance enhancement, they seem to contradict each other and can be hardly well-balanced. Herein, we designed electrode particles consisting of numerous nanograins with uniform crystalline orientation to guarantee both high surface area and high structural integrity, allowing the significant improvement of Li + storage kinetics and performance. Applying this “mesocrystallizing” strategy to a NiCo 2 O 4 -based anode, resulting in various degrees of pseudocapacitance response, the long-term cyclability and rate performance of this material have been largely enhanced. Impressively, the mesocrystalline NiCo 2 O 4 electrode exhibits a high reversible capacity of 1403 mAh g -1 after 200 cycles at 1.6 A g -1 (a rate of 1.8 C). The growth mechanism of mesocrystalline materials with different morphologies is identified to be a topotactic strctural transition process featuring a gradual edge-to-core corrasion process. This work presents an important synthetic clue to balance the morpholgy and crystallinity of battery electrode materials for their perforamnce optimization and is expected to inspire future structural design for battery materials beyond the one prototyped here.

25 ENERGY STORAGE↗
DOE OSTI2023

Layer-by-Layer-Processed Organic Solar Cells with 18.02% Efficiency Enabled by Regulating the Aggregation of Bottom Polymers

The fabrication of organic solar cells (OSCs) by a layer-by-layer (LBL) method has attracted growing attention in recent years. As already known, the pre-aggregates of conjugated polymers in solution have a profound impact on their microstructure morphology in films. Herein, by simply controlling the solution temperature and annealing processes, the pre-aggregation behavior of D18 polymer in solution can be fine-tuned and the microstructure of D18 bottom layer is well manipulated. The optimized D18 bottom layer can effectively regulate L8-BO upper-layer-forming suitable networks for efficient charge transportation. In addition, a vertical phase separation with a special D/D:A/A structure (P-i-N-type component distribution) is also formed. As a result, compared to the 16.43% power conversion efficiency (PCE) of the bulk heterojunction devices, such control enables bilayer OSC devices based on the polymer D18 and L8-BO to deliver an enhanced PCE of 18.02% with simultaneously improved short-circuit current density, open-circuit voltage, and fill factor. Importantly, it is also demonstrated in these results that the LBL deposition process utilizing the pre-aggregation of polymer and its fiber-network-forming ability is a very promising approach to improve charge dynamics, suppress carrier recombination, and fabricate highly efficient OSCs.

14 SOLAR ENERGY↗
DOE OSTI2022

Bicontinuous substrates with reduced pore restriction for CO 2 -selective composite membranes

A substrate with bicontinuous structure is attractive for thin-film composite (TFC) membrane synthesis due to its high surface porosity and well-interconnected bulk morphology. In this study, the vapor-induced phase separation (VIPS) of the casting solution comprising water, 2-pyrrolidone, and polyethersulfone (PES) was studied. By tuning the water addition in the casting solution and water vapor exposure time, the optimized substrate exhibited a bicontinuous surface with a high porosity of 24.2% (or 216/µm 2 pore density), thereby mitigating pore restriction and showing a high CO 2 permeance of 2.94×10 5 GPU. Compared to the benchmark PES substrate with cellular surface pores and lower gas permeance, the use of the bicontinuous substrate led to a 12% increase in the CO 2 permeance of the TFC membrane. The mitigated pore restriction was further rationalized by a resistance-in-series model. The analysis of the lateral diffusion and substrate resistances indicates that an even higher surface pore density of the substrate is required to fully realize the potential of ultra-permeable, CO 2 -selective polymers in the TFC configuration. As a result, the scalability of the VIPS process was demonstrated by the roll-to-roll fabrication of the optimized bicontinuous substrate with a width of 21" and a length of >100'.

42 ENGINEERING↗
DOE OSTI2026

Time of Flight Secondary Ion Mass Spectrometry for Characterization of Pt-Coated Porous Transport Layers in PEM Water Electrolyzers

Titanium-based porous transport layers (PTLs) and iridium-based catalyst layers (CLs) are two main components of proton exchange membrane water electrolyzers (PEMWEs). PTLs are typically coated with platinum to minimize interfacial losses and to support long-term operation. Optimizing coatings and the PTL-CL interface requires comprehensive characterization. This study establishes time-of-flight secondary ion mass spectrometry (ToF-SIMS) as a valuable technique for PTL characterization, addressing capabilities and limitations related to PTL morphology. A methodology was developed that uses a Cs + sputter beam for dynamic depth profiling, with data collected in both positive-ion (MCs + ) and negative-ion modes to generate depth profiles, 2D ion maps, and 3D ion reconstructions. ToF-SIMS detected relative differences in platinum-layer thickness between samples; these trends were validated by cross-sectional scanning transmission electron microscope (STEM) measurements and flat-titanium substrate controls. Interfacial oxide layers are identified in both ion modes, with enhanced oxide sensitivity in negative mode. The technique’s high sensitivity enables detection of nanometer-scale coatings and trace impurities within the bulk PTL structure. These results provide a methodological framework for analyzing Pt-coated PTLs, with the potential to extend to other components in PEMWEs and other electrolyzer systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Structural anisotropy in Sb thin films

Sb thin films have attracted wide interest due to their tunable band structure, topological phases, high electron mobility, and thermoelectric properties. We successfully grow epitaxial Sb thin films on a closely lattice-matched GaSb(001) surface by molecular beam epitaxy. We find a novel anisotropic directional dependence on their structural, morphological, and electronic properties. The origin of the anisotropic features is elucidated using first-principles density functional theory (DFT) calculations. The growth regime of crystalline and amorphous Sb thin films was determined by mapping the surface reconstruction phase diagram of the GaSb(001) surface under Sb 2 flux, with confirmation of structural characterizations. Crystalline Sb thin films show a rhombohedral crystal structure along the rhombohedral (211) surface orientation parallel to the cubic (001) surface orientation of the GaSb substrate. At this coherent interface, Sb atoms are aligned with the GaSb lattice along the [1̄10] crystallographic direction but are not aligned well along the [110] crystallographic direction, which results in anisotropic features in reflection of high-energy electron diffraction patterns, misfit dislocation formation, surface morphology, and transport properties. Our DFT calculations show that the preferential orientation of the rhombohedral Sb (211) plane may originate from the GaSb surface, where Sb atoms align with the Ga and Sb atoms on the reconstructed surface. The formation energy calculations confirm the stability of the experimentally observed structures. Our results provide optimal film growth conditions for further studies of novel properties of Bi 1-x Sb x thin films with similar lattice parameters and an identical crystal structure, as well as functional heterostructures of them with III–V semiconductor layers along the (001) surface orientation, supported by a theoretical understanding of the anisotropic film orientation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

HPC for Optimizing Process Parameters to Control Material Evolution in Seamless Induction Hardening of Wind Turbine Main Shaft Bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

HPC for optimizing process parameters to control material evolution in seamless induction hardening of wind turbine main shaft bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

17 WIND ENERGY↗
DOE OSTI2024

Quantitative Particle Analysis of Neptunium-237 Oxides: Optimization of MAMA Analysis for Modified Direct Denitration Products

The production of plutonium-238 through irradiation of neptunium-237 ( 237 Np) target materials for the use in radioisotope thermoelectric generators is paramount for continued deep space exploration. This work employs scanning electron microscopy to analyze 237 Np materials coupled with a well-developed image analysis framework (Morphological Analysis for Material Attribution, or MAMA) to determine the degree of micron-scale homogeneity in the materials. This work demonstrated how the quantification of particle characteristics can validate production materials and affirm the qualitative similarities observed in micrographs. The 237 Np oxide particle analysis determined that the materials from five production runs were quantitatively homogenous (significant at α = 0.05) in particle area, circularity, equivalent circular diameter, and ellipse aspect ratio, with two of the sampling dates having statistically significant different means for one of the four characteristics. Furthermore, these metrics not only confirm general homogeneity of the material but also expand the application of MAMA workflows to 237 Np materials, demonstrating the utility of MAMA analysis for a wider breadth of nuclear materials than previously reported. In the open literature, this study is the first time that these microanalytical techniques were applied to 237 Np materials to this degree.

MAMA↗
DOE OSTI2021

Phase segregation mechanisms of small molecule-polymer blends unraveled by varying polymer chain architecture

As phase separation between the small-molecule semiconductor and the polymer binder is the key enabler of blend-based organic field-effect transistors (OFETs) fabricated by low-cost solution processing, it is crucial to understand the underlying phase separation mechanisms that determine the phase morphology, which significantly impacts device performance. Beyond the parameter space investigated in previous work, here we investigate the formation of blends by varying the branch architecture of the polymer binder and by shortening the solvent dry time using ultrasonic spray casting. The phase morphologies of the resulting blend films have been thoroughly characterized with a variety of techniques in three dimensions over multiple length scales, including AFM, energy-filtered transmission electron microscope, and neutron reflectivity, and have been correlated with electrical transport performance. From the results, we have inferred that the phase morphology is kinetically determined, limited by the inherent slow movement of polymer macromolecules. The kinetic picture, supported by molecular dynamics modeling, not only consistently explains our observations but also resolves inconsistencies in previous works. The achieved mechanistic understanding will guide further optimization of blend-based organic electronics, such as OFETs and organic photovoltaics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimized simple and affordable procedure for differentiation of monocyte-derived dendritic cells from LRF: An accessible and valid alternative biological source

Dendritic cells are one of the most popular immune cells, which plays a remarkable role in both immunotherapy and tolerance induction. Due to unwanted side effects of leukocyte presence in donated blood, the policy of blood service is the pre-storage reduction of leukocytes, which today, filtration is the most common method for this purpose. The filtration method has led to diminished access to Buffy coat as a generally used conventional source of biological cells. We developed a simple, affordable, and reproducible method for dendritic cell differentiation from filter-derived monocytes and, the results of the filter study were compared with differentiated DCs from the conventional buffy coat-derived monocytes. The Monocytes were recovered from leukoreduction filter using an optimized protocol with supplemented PBS buffer. Following the adhesion method, CD14{sup +} Monocyte-enriched population with the purity of 94 % was obtained. After cytokine stimulation over a 6-day period and maturation induction by LPS, differentiated DCs were evaluated for morphology, surface markers (CD86, CD40, CD83 and, HLA-DR), antigen uptake potency and IL-12 secretion. Analysis and comparison of the results represented no significant difference between the two groups. Accordingly, we conclude that leukoreduction filters could be introduced as a reliable and research-grade source of monocyte for DC generation in biological research.

60 APPLIED LIFE SCIENCES↗