Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Nanostructure refinement and phase formation of flash annealed FeNi-based soft magnetic alloys

In this work, the resulting nanocomposite microstructures of FeNi nanocrystallites under different heating and cooling rates (5 °C/min vs 400-500 °C/s) is investigated. Conventional furnace annealing under low heating rates and slow cooling resulted in both BCC α-FeNi and FCC γ-FeNi nanocrystallites with an average grain size on the order of 25-27 nm whereas high heating rates achieved via flash annealing techniques have enabled a dramatically refined microstructure consisting of 5-7 nm grains with FCC γ-FeNi phase and found to be the dominant phase following primary crystallization. Grain size refinement and phase identity optimization yielded low values of coercivities-17 A/m and high permeability similar to 11 x 10 3 measured at 400 Hz/1 kA/m in flash annealed samples at 450 °C for 5 s. The magnetic behavior and the underlying mechanism of optimal soft magnetic properties are discussed in terms of the critical role of the grain size in domain wall pinning and coercivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure-Dependent Rate Theory Model of Radiation-Induced Segregation in Binary Alloys

Conventional rate theory often uses the mean field concept to describe the effect of inhomogeneous microstructures on the evolution of radiation induced defect and solute/fission product segregation. However, the spatial and temporal evolution of defects and solutes determines the formation and spatial distribution of radiation-induced second phase such as precipitates and gas bubbles/voids, especially in materials with complicated microstructures and subject to high dose radiation. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed to investigate the effect of inhomogeneous thermodynamic and kinetics properties of defects on diffusion and accumulations of solute A in AB binary alloys. Four independent concentrations: atom A, interstitial A, interstitial B, and vacancy on [A, B] sublattice are used as field variables to describe temporal and spatial distribution and evolution of defects and solute A. The independent concentrations of interstitial A and interstitial B allow to describe their different generation rates, thermodynamic and kinetic properties, and release the assumptions of interstitial generation and sink strength used in the conventional rate theory. Microstructure and concentration dependent chemical potentials of defects are used to calculate the driving forces of defect diffusions. With the model, the effects of defect chemical potentials and mobilities on the RIS in polycrystalline AB model alloys have been simulated. The results demonstrated the model capability in predicting defect evolution in materials with inhomogeneous thermodynamic and kinetic properties of defects. The model can be extended to materials with complicated microstructures such as a wide range of grain size distribution, coating structure and multiphases as well as radiation-induced precipitation subject to severe radiation damage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of docetaxel on mechanical properties of ovarian cancer cells

Docetaxel could inhibit the proliferation of tumor cells by targeting microtubules. The extension of cellular microtubules plays an important role in the invasion and metastasis of tumor cells. This paper aims to study the distribution and mechanical properties of cytoskeletal proteins with low concentration of docetaxel. MTT assay was used to detect the minimum drug activity concentration of docetaxel on SKOV-3 cells, fluorescence staining was used to analyze the distribution of cytoskeleton proteins, scanning electron microscopy(SEM) was used to observe the morphology of single cells, and atomic force microscopy(AFM) was used to determine the microstructure and mechanical properties of cells. The results showed that the IC{sub 10} of docetaxel was 1 ng/ml. Docetaxel can effectively inhibit the formation of cell pseudopodia, hinder the indirectness between cells, reduce the cell extension area, and make the cells malformed. In addition, when AFM analyzes the effects of drugs on cell microstructure and mechanical properties, the average cell surface roughness and cell height are positively correlated with the concentration of docetaxel. Especially when the concentration was 100 ng/ml, the adhesion decreased by 37.04% and Young's modulus increased by 1.57 times compared with the control group. This may be because docetaxel leads to microtubule remodeling and membrane protein aggregation, which affects cell microstructure and increases cell strength, leading to significant changes in the mechanical properties of ovarian cells. This is of great significance to the study of the formation mechanism of tumor cell invasion and migration activities mediated by actin.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Bulk nanocrystalline Al alloys with hierarchical reinforcement structures via grain boundary segregation and complexion formation

Grain size engineering, particularly reducing grain size into the nanocrystalline regime, offers a promising pathway to further improve the strength-to-weight ratio of Al alloys. Unfortunately, the fabrication of nanocrystalline metals often requires non-equilibrium processing routes, which typically limit the specimen size and require large energy budgets. In this study, multiple dopant elements in ternary Al alloys are deliberately selected to enable segregation to the grain boundary region and promote the formation of amorphous complexions. Three different fully dense bulk nanocrystalline Al alloys (Al-Mg-Y, Al-Fe-Y, and Al-Ni-Y) with small grain sizes were successfully fabricated using a simple powder metallurgy approach, with full densification connected directly to the onset of amorphous complexion formation. All the compositions demonstrate densities above 99% with grain sizes <60 nm following consolidation via hot pressing at 585 °C. The very fine grain structure results in excellent mechanical properties, as evidenced by nanoindentation hardness values in the range of 2.2-2.8 GPa. Detailed microstructural characterization verifies the segregation of all dopant species to grain boundaries as well as the formation of amorphous complexions, which suggests their influential role in aiding effective consolidation and endowing thermal stability in the alloys. Moreover, nanorods with a core-shell structure are also observed at the grain boundaries, which likely contribute to the stabilization of the grain structure while also strengthening the materials. Lastly, intermetallic particles with sizes of hundreds of nanometers form in all systems. As a whole, the results presented here demonstrate a general alloy design strategy of segregation and boundary evolution pathway that enables the fabrication of multiple nanocrystalline Al alloys with hierarchical microstructures and improved performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing of a metastable high entropy alloy: Metastability engineered microstructural control via process variable driven elemental segregation

Compositional paradigm shift in high entropy alloys (HEAs) provided new opportunities for microstructural engineering, whereas process control during laser powder bed fusion (LPBF) additive manufacturing (AM) enable fine microstructure tailoring. Metastability engineering in transformation induced plasticity (TRIP) HEAs by addition of minor alloying elements is an attractive strategy for fine microstructural tuning. This study explored in detail the microstructural evolution during LPBF AM of a metastable Fe 40 Mn 20 Co 20 Cr 15 Si 5 (at.%) dual phase HEA (CS-HEA). LPBF processing window for CS-HEA was established based on quantitative analysis and experiments. Based on melt pool overlap lack of fusion pores were observed at lower energy densities (J) of $\textit{J}$ ≤ 31.25 J/mm 3 and key-hole formation by melt pool destabilization in case of $\textit{J}$ ≥ 75 J/mm 3 . The microstructure of CS-HEA consists of metastable FCC-γ and HCP-ε phases; LPBF process parameters governed the final phase fraction in the alloy which has been correlated to metastability alteration of the high temperature γ phase. Final microstructural engineering was devised by LPBF process control which enabled cooling rate manipulation to guide Mn and Si segregation at the cell boundaries, thereby controlling the matrix metastability and final phase fraction. Additionally, high resolution transmission electron microscopy (TEM) revealed disparity in stacking fault morphology in CS-HEA with LPBF process variable alterations associated with local variations in chemical composition and stacking fault energy. Further, the phase evolution with process parameters also affected the nanomechanical behavior of the alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Kinetics and Thermodynamics of Sr Permeation in CeO 2 -Based Barrier Layers for Solid-Oxide Electrolyzer Cells

Solid-oxide electrolyzer cells (SOECs) convert steam to hydrogen efficiently at high temperatures. However, during operation, the diffusion of cations or impurities through the cells due to electrode degradation can cause unwanted secondary phases to form, which may degrade device performance. Here, in this study, we use atomistic and mesoscale simulations coupled with experimental analysis to study the diffusion of Sr through the Gd-doped CeO 2 (GDC) barrier layer used to protect the yttria-stabilized zirconia (YSZ) electrolyte in SOECs. From our atomistic calculations, we find Sr diffusion to be negligibly slow in bulk GDC; however, surface diffusion is much more favorable. Subsequent mesoscale simulations show that Sr diffusion is activated when the porosity of GDC exceeds ∼10% and significantly exceeds diffusion in bulk and grain boundary regions. We also find that SrO-based species can accumulate at GDC surfaces; however, SrO aggregation and coarsening will be limited by the large lattice mismatch between GDC and SrO. Energy-dispersive X-ray spectroscopy (EDS) and electron diffraction confirm that Sr can accumulate within GDC pores and form disperse Sr-containing secondary phases. Altogether, Sr diffusion in dense GDC is unlikely to give rise to thick SrO layers, which would severely limit device performance. The formation of Sr-containing secondary phases can largely be avoided by restricting the porosity of the GDC layer as much as possible.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of decades of corrosion on the microstructure of altered glasses and their radiation stability

Understanding the microstructural evolution of glasses during their interaction with water and radiation is of fundamental importance in addressing the corrosion of nuclear waste forms under geological disposal conditions. Here we report the results of more than 21 years of corrosion of two borosilicate glasses showing the formation of mesoporous C–S–H gels in Ca-bearing glasses and a mainly microporous microstructure in Al-bearing glasses. These porous corroded glasses were then irradiated with heavy ions to simulate the effects of recoil nucleus damage and monitored in real time using transmission electron microscopy with in situ ion irradiation. The ballistic collisions remarkably healed the porous corroded glasses to a pore-free homogeneous microstructure. Besides providing new insights and predictions about how doped glasses and actual waste forms may evolve under corrosion and irradiation, the results highlight the non-universal nature of the existing corrosion models and the important role that the glass composition and radiation damage play in the evolution of the microstructure during corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Poromechanical Framework for Internal Interactions Induced by Solid Inclusions

The framework of poromechanics is generalized to simulate the multiscale behavior of porous media subjected to internal loadings stemming from the growth of solid inclusions. This generalization is designed to enable the study of anisotropic internal stress generation from solid growth within the pores, while recovering isotropic fluid-induced loading as a particular case. For this purpose, a mathematical strategy to define constitutive tensors in a thermodynamically consistent form is proposed, thus offering new opportunities for determining the poromechanical properties of a porous solid through advanced experimentation or micromechanical models. The framework is specialized by means of established elastic solutions for single pore–matrix interaction, as well as through homogenization schemes considering the interaction among congruent pores. In particular, the second Eshelby solution and the Tanaka–Mori–Benveniste homogenization scheme are used to derive a microporoelastic model. At an elemental scale, the model is tested under mixed control conditions by replicating different scenarios of geomaterial testing. In addition, the model characteristics are outlined with reference to inelastic microscopic loadings replicating chemo-mechanical forcing, such as expansive crystal formation. Through a series of parametric analyses, it is shown that the microstructure of the pores significantly influences the properties of porous media. Most notably, it is shown that the effects of a solid forming within the pores depend in a highly nonlinear fashion on the constitutive characteristics of the inhomogeneities and can therefore not be readily quantified or predicted without models capturing the diverse multiscale interactions among pores, inhomogeneities, and matrix.

chemomechanics↗
DOE OSTI2026

Process-driven roadmap for depositing super duplex stainless steel via wire Arc additive manufacturing

Here, this study systematically investigates the effects of shielding gas, bead spacing, weld mode, and travel speed on the phase balance, porosity, and hardness of wire arc additively manufactured (WAAM) super duplex stainless steel (ER2594). Robotic WAAM was employed to fabricate multilayer walls under systematically varied process conditions, followed by phase transformation simulations, X-ray computed tomography (XCT), electron backscatter diffraction (EBSD), and microhardness evaluation. Thermodynamic simulations predicted rapid cooling of AM process can suppress the potential formation of deleterious precipitates which was later validated via cross-sectional microstructure analyses of printed samples. XCT revealed porosity levels below 0.2% for all deposits, with reduced travel speed significantly lowering defect volume. Microstructural analyses revealed the evolution of various austenite precipitates, including grain boundary austenite (GBA), Widmanstätten austenite (WA), and intergranular austenite (IGA), sequentially upon cooling of the ferrite phase. Among all process parameters, weld transfer mode exhibited the strongest influence on phase balance; pulsed mode promoted higher ferrite retention (~ 36%) compared to RapidX mode. No consistent relationship between stabilized phase fraction and captured microhardness was observed. This work provides critical insights for optimizing WAAM parameters to control phase balance and mechanical performance, which is essential for producing high-integrity super duplex stainless-steel components for nuclear and marine applications.

Grain orientation↗
DOE OSTI2022

Surprisingly high irradiation-induced defect mobility in Fe 3 O 4 as revealed through in situ transmission electron microscopy

Radiation-induced defects are expected to change the corrosion kinetics when a material is exposed to a corrosive environment. Characterization of the defects forming under irradiation and their ability to move/diffuse is therefore key to understanding how they impact the corrosion kinetics and possibly mechanisms. For that matter, Fe/Fe 3 O 4 interfaces were irradiated using 1 MeV Kr 2+ at temperatures of 273 K (25 °C), 573 K (300 °C) and 773 K (500 °C) to a maximum dose of 10 dpa (as measured in the Fe matrix) in situ in a transmission electron microscope. The evolution of the microstructure was followed as a function of the dose and temperature. The formation of defects was followed in the metal and the oxide as well as at the metal/oxide interface and characterized in terms of size and density. Additionally, the dynamic observation of the spatial distribution of the defects allowed for a qualitative assessment of the mobility of defects in the oxide as a function of temperature, revealing evidence for enhanced mobility even more so than in the Fe matrix. Mechanisms of induced defect mobility in the spinel are discussed to account for the observations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reaction Current Heterogeneity at the Interface between a Lithium Electrode and Polymer/Ceramic Composite Electrolytes

Although lithium metal anodes are expected to increase the energy density of next-generation batteries, dendrite growth during charge remains a major bottleneck preventing widespread implementation. Composite solid electrolytes with ceramic particles embedded in a polymer matrix have the potential to prevent dendrites owing to the higher mechanical stiffness while also possessing the flexibility to maintain contact with the electrode. However, microscopically, the different mechanical and electrochemical properties of the polymer and ceramic domains can cause inhomogeneous charge transfer at the Li/electrolyte interface, which can lead to nonuniform Li deposition and propagation of dendrites. Here, we computationally examine the coupled electrochemical, transport, and mechanical processes at the interface to determine the propensity for dendrite formation and possible approaches to mitigate this issue. Predictions of two possible microstructures at the interface, namely, (i) where both the polymer and ceramic come in contact with Li metal and (ii) when only the polymer comes in contact with Li metal, suggest that the former has a greater tendency for nonuniform plating. In addition, predictions suggest that minimizing the interfacial resistance between polymers and ceramics and incorporating interlayers between the electrode and electrolyte help mitigate current heterogeneity. In conclusion, these predictions provide guidance for experimental approaches to prevent dendrites in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2024

Breaking Boundaries: Deformation Processing Techniques for the Next Generation of Lightweight and High-Strength Materials

This chapter emphasizes the importance of solid phase processing (SPP) techniques in developing advanced materials for lightweight and high-strength applications. SPP methods like friction stir welding, and shear-assisted processing can create new microstructures and process materials in novel ways. SPP can enhance mechanical performance via various strengthening mechanisms like solid solution supersaturation, Hall-Petch and Orowan effects, and misorientation angle grain boundaries. The potential for in situ alloying or joining of components with near-net shape and low energy inputs, even for immiscible systems with high enthalpies of mixing, is also discussed. The chapter explores the concept of metastability through microstructural manipulation and the role of advanced characterization for atomistic understanding. The formation of metastable grain, shear-driven chemical mixing, and transformation pathways are also discussed. Finally, the emerging trends for SPP and the challenges that need to be addressed before realizing the full potential of these techniques are presented.

Lastovich, Michael↗
DOE OSTI2022

Self‐Assembly of Helical Nanofibrous Chiral Covalent Organic Frameworks

Abstract Despite significant progress on the design and synthesis of covalent organic frameworks (COFs), precise control over microstructures of such materials remains challenging. Herein, two chiral COFs with well‐defined one‐handed double‐helical nanofibrous morphologies were constructed via an unprecedented template‐free method, capitalizing on the diastereoselective formation of aminal linkages. Detailed time‐dependent experiments reveal the spontaneous transformation of initial rod‐like aggregates into the double‐helical microstructures. We have further demonstrated that the helical chirality and circular dichroism signal can be facilely inversed by simply adjusting the amount of acetic acid during synthesis. Moreover, by transferring chirality to achiral fluorescent molecular adsorbents, the helical COF nanostructures can effectively induce circularly polarized luminescence with the highest luminescent asymmetric factor ( g lum ) up to ≈0.01.

Tang, Xihao↗
DOE OSTI2024

Formation kinetics and thermodynamic stability of the Aurivillius compounds in Bi 4 Ti 3 O 12 –BiFeO 3 system

Abstract The Aurivillius compounds in the Bi 2 O 3 –Fe 2 O 3 –TiO 2 system, combining ferroelectric, semiconducting, and ferromagnetic properties, have attracted particular interest. Formation kinetics and thermodynamic stability are the fundamental knowledge needed for modeling and predicting the temporal microstructure and property evolution during materials processing but have not yet been addressed by quantitative experimental measurement. This article focuses on the Bi n +1 Fe n –3 Ti 3 O 3 n +3 Aurivillius compounds on the Bi 4 Ti 3 O 12 –BiFeO 3 tie‐line to elucidate the mechanisms and thermodynamic controls responsible for phase formation of compounds with various perovskite‐like layers. Five high‐purity Aurivillius compounds Bi 4 Ti 3 O 12 , Bi 5 FeTi 3 O 15 , Bi 6 Fe 2 Ti 3 O 18 , Bi 7 Fe 3 Ti 3 O 21 , and Bi 8 Fe 4 Ti 3 O 24 with integer n = 3–7 values were synthesized and their phase transformation properties and enthalpies of formation were studied by X‐ray diffraction in situ, high temperature differential scanning calorimetry, and high temperature oxide melt solution calorimetry. Thermodynamic stability of the compounds decreases with increasing n , and formation kinetics gradually slow down, demonstrating the inherent difficulty to synthesize pure Aurivillius compounds with n larger than 8. This difficulty was confirmed by an impurity phase coexisting with Bi 9 Fe 5 Ti 3 O 27 .

Gong, Weiping↗
DOE OSTI2020

Effect of synthesis temperature on the phase formation of NiTiAlFeCr compositionally complex alloy thin films

Here, the synthesis temperature dependent phase formation of Ni 10 Ti 10 Al 25 Fe 35 Cr 20 thin films is compared to a bulk processed sample of identical composition. The as-cast alloy exhibits a dual-phase microstructure which is composed of a disordered BCC phase and AlNiTi-based B2- and/or L2 1 -ordered phase(s). Formation of the BCC phase as well as an ordered AlNi-based B2 phase is observed for a thin film synthesised at 500 °C (ratio of synthesis temperature of thin film to melting temperature of bulk alloy: T/T m = 0.49), which is attributed to both surface and bulk diffusion mediated growth. Post deposition annealing at 900 °C (T/T m = 0.75) of a thin film deposited without intentional heating results in the formation of NiAlTi-based B2 and/or L2 1 -phase(s) similar to the bulk sample, which is attributed to bulk diffusion. Depositions conducted at room temperature without intentional substrate heating (T/T m = 0.20) resulted in the formation of an X-ray amorphous phase, while a substrate temperature increase to 175 °C (T/T m = 0.28) causes the formation of a BCC phase. Atom probe tomography of the thin films deposited without intentional substrate heating and at 175 °C indicates the formation of ~5 nm and ~10 nm FeAl-rich domains, respectively. This can be rationalized based on the activation energy for surface diffusion, as Ti and Ni exhibt 2.5 to 4 times larger activation energy barriers than Al, Fe and Cr. It is evident from the homologous temperature that the phase formation observed at 500 °C (T/T m = 0.49) is a result of both surface and bulk diffusion. As the temperature is reduced, the formation of FeAl-rich domains can be understood based on the differences in activation energy for surface diffusion and is consistent with kinetically limited thin film growth.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The microstructure of a selective laser melting (SLM)-fabricated NiTi shape memory alloy with superior tensile property and shape memory recoverability

A selective laser melting (SLM)-fabricated NiTi with superior tensile property and shape memory recoverability was obtained by using a unique stripe rotation scanning strategy. Here, the alloy characteristics, formation mechanisms and evolution in terms of twins, dislocations and precipitations of the alloy were systematically studied. Compared to the conventional smelting-followed-by-machining, the SLM fabrication process involves rapid solidification and repeated heating, which confer distinctive characteristics to the microstructures of SLM-fabricated NiTi alloys. Rapid solidification promotes the formation of a supersaturation solid solution matrix containing a high concentration vacancies, which in turn aggregate to generate a high density of dislocations. During subsequent repeated heating stages, these dislocations occur thermal motion along three directions of <001 > , <111> and <110 >, leading to the formation of thermal kinks, helical dislocations and wave morphology. Simultaneously, precipitated particles Ti 3 Ni 4 repeatedly nucleate and heterogeneous grow with the movement of dislocation. Such precipitation behavior, termed repeated precipitation, has not been previously reported in the conventional NiTi alloys, suggesting that it could be a unique characteristic of such alloy. After martensitic transformation, only two twins, {1 1¯ 1} type I twin and compound twin, are detected. The twinning lamellae of these two twins, where precipitation and dislocation pile-ups exist, often have uneven thickness and chaotic arrangement. Besides, the unique self-accommodated microstructures, such as secondary {1 1¯ 1} type I twin and compound twin with “herring-bone’’ lamellae, which often appear in the deformed or nanocrystalline NiTi, can also be observed. These unique microstructures may confer the distinctive properties to the SLM-fabricated NiTi.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental investigation of the dependence of void nucleation and growth on initial microstructure in high-purity titanium under tension

An experimental investigation of failure mechanisms in relation to the initial microstructure in high-purity titanium samples is presented. The initial microstructure of the specimens was measured in 3D using diffraction-contrast tomography (DCT). Ex-situ X-ray computed tomography (XCT) was used to visualize voids in specimens at various levels of deformation attained by interrupted tensile testing. Electron backscatter diffraction (EBSD) mapping was used to characterize the deformed microstructures per specimen. The investigation showed that the location of failures was unrelated to the formation of the first voids, but rather the nucleation and growth of cracks were from heavily deformed surface regions. The areas surrounding the failure-causing cracks had the highest propensity for void development of any area in the specimen. This facilitated crack propagation through the specimen via “linking up”. The failure of the specimens by microvoid coalescence was bolstered by “dimpled” fracture surfaces. Paint composed of gallium embedded in rubber was used to track the displacement of points along the loading direction of the specimens, to relate the location of failure to the material's initial microstructure. However, the correlation proved difficult, due to complex microstructural evolution involving voids, grain fragmentations, and profuse twinning. Nevertheless, it was shown that necking occurred near the largest grain in the gauge section of the specimens. This is likely caused by the decrease in strength of larger grains, causing strain to concentrate in their vicinity. Here, a comprehensive picture of the failure processes in high-purity titanium under axial loading is presented and discussed in the paper.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigating stainless steel/aluminum bimetallic structures fabricated by cold metal transfer (CMT)-based wire-arc directed energy deposition

Here, this study investigated the process of fabricating a bimetallic structure of 316L stainless steel (SS) and 4043 aluminum (Al) using wire-arc directed energy deposition (DED) based on the cold metal transfer (CMT) process. The impact of heat input on the fabricated structure’s geometry, porosity, and microstructures at the interface, with a specific emphasis on the intermetallic compound (IMC) formation, and the subsequent impact on the joint strength of the structure, were studied. The IMC layer at the interface was predominantly comprised of FeAl 2 Si. For the various heat input conditions studied, the IMC layer's thickness varied from 5 µm to 18 µm. The tensile strength reached up to approximately 130 MPa, which is among the highest reported in the literature for steel/Al bimetallic structures. The specimens fabricated with high heat input conditions had a thicker IMC layer at the steel/Al interface, resulting in a more brittle interface and degradation of the mechanical properties.

36 MATERIALS SCIENCE↗