Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A double-stage injection-locked oscillator for optically fed phased array antennas

In an optically fed phased array antenna system, the microwave carrier signal is transmitted via a modulated lightwave to each active T/R (transmit/receive) module, where it must be converted back to the microwave domain. Currently, efficient optical-to-microwave conversion is extremely difficult, as the detected microwave signal is weak and noisy. A novel circuit, containing a high-gain/low-noise microwave injection-locked oscillator, has been developed to improve the interface between the optical and microwave components. The circuit utilizes two FETs and a dielectric resonator, which serves as a frequency-dependent feedback element. The circuit, designed to operate at about 8 GHz, provides significant amplitude and phase noise suppression. In addition, the circuit realization is compatible with MMIC technology.

Berceli, Tibor↗
NASA NTRS1990

Performance of a 300 Mbps 1:16 serial/parallel optoelectronic receiver module

Optical interconnects are being considered for the high speed distribution of multiplexed control signals in GaAs MMIC-based phased array antennas. This paper describes the performance of a hybrid GaAs optoelectronic integrated circuit (OEIC), along with a description of its design and fabrication. The OEIC converts a 16-bit serial optical input to a 16 parallel line electrical output using an on-board 1:16 demultiplexer and operates at data rates as high as 305 Mbps. The performance characteristics as well as potential applications of the device are presented.

Richard, M. A.↗
NASA NTRS1991

Microstrip antenna developments at JPL

The in-house development of microstrip antennas, initiated in 1981, when a spaceborne lightweight and low-profile planar array was needed for a satellite communication system, is described. The work described covers the prediction of finite-ground-plane effects by the geometric theory of diffraction, higher-order-mode circularly polarized circular patch antennas, circularly polarized microstrip arrays with linearly polarized elements, an impedance-matching teardrop-shaped probe feed, a dual-polarized microstrip array with high isolation and low cross-polarization, a planar microstrip Yagi array, a microstrip reflectarray, a Ka-band MMIC array, and a series-fed linear arrays.

Huang, John↗
NASA NTRS1991

Solid State Technology Branch of NASA Lewis Research Center

Reprints of one year's production of research publications (June 1990 to June 1991) are presented. These are organized into three major sections: microwave circuits, both hybrid and monolithic microwave integrated circuits (MMICs); materials and device work; and superconductivity. The included papers also cover more specific topics involving waveguides, phase array antennas, dielectrics, and high temperature superconductors.

Source record↗
NASA NTRS1992

A 1-W, 30-ghz, CPW Amplifier for ACTS Small Terminal Uplink

The progress is described of the development of a 1 W, 30 GHz, coplanar waveguide (CPW) amplifier for the Advanced Communication Technology Satellite (ACTS)Small Terminal Uplink. The amplifier is based on Texas Instruments' monolithic microwave integrated circuit (MMIC) amplifiers; a three stage, low power amplifier, and a single stage, high power amplifier. The amplifiers have a power output of 190 mW and 0.710 W, gain of 23 and 4.2 dB, and efficiencies of 30.2 and 24 percent for the three stage and one stage amplifiers, respectively. The chips are to be combined via a CPW power divider/combiner circuit to yield the desired 1 W of output power.

Taub, Susan R.↗
NASA NTRS1992

Solid State Technology Branch of NASA Lewis Research Center

A collection of papers written by the members of the Solid State Technology Branch of NASA LeRC from Jun. 1991 - Jun. 1992 is presented. A range of topics relating to superconductivity, Monolithic Microwave Circuits (MMIC's), coplanar waveguides, and material characterization is covered.

Source record↗
NASA NTRS1992

An optically controlled Ka-band phased array antenna

The design and development of a small, optically controlled phased array antenna suitable for communication satellite applications are discussed. A vertical integration architecture is used which minimizes the size of the array with its associated beamforming network (BFN). The antenna features a four-element linear microstrip array that uses aperture coupling of the antenna elements to the BFN; a modified Wilkinson power divider BFN; and 32 GHz, four-bit monolithic microwave integrated circuit (MMIC) phase shifters in customized quartz packages with corresponding optoelectronic interface circuits (OEIC's) for control signal reception.

Kunath, R. R.↗
NASA NTRS1992

A 1-W, 30-GHz, CPW amplifier for ACTS small terminal uplink

The progress to date of the development of a 1-W, 30-GHz, coplanar waveguide (CPW) amplifier for the Advanced Communication Technology Satellite (ACTS) Small Terminal Uplink is described. The amplifier is based on Texas Instruments' monolithic microwave integrated circuit (MMIC) amplifiers; a three-stage, low-power amplifier and a single stage, high-power amplifier. The amplifiers have a power output of 190 mW and 0.710 W, gain of 23 and 4.2 dB, and efficiencies of 30.2 and 24 percent for the three-stage and one-stage amplifiers, respectively. The chips are to be combined via a CPW power divider/combiner circuit to yield the desired 1 W of output power.

Taub, Susan R.↗
NASA NTRS1992

Challenges of a 20/30 GHz Personal Access Satellite System

By taking advantage of available MMIC technology, in conjunction with the ample bandwidth that is available in the 20/30 GHz bands, a Personal Access Satellite System (PASS) will be able to advance mobile satellite communications to a level of availability at which both personal and business related services can be conducted at data rates of the order of as much as 1.544 Mbps. PASS-related research is currently attempting to identify requisite system architectures, multiple-access schemes, and such space and ground segment requirements as user antenna designs, frequency separation, rain attenuation, and terminal radiation safety.

Sue, Miles K.↗
NASA NTRS1992

Experimental code verification results for reflector antenna distortion compensation by array feeds

Electronic compensation of reflector surface distortion using array feed with individual amplitude and phase control of the array elements is becoming increasingly attractive because of the recent advances in monolithic microwave integrated circuit (MMIC) technology. An algorithm has been developed previously using the concept of focal plane conjugate field matching in the receive mode and a computer code has been generated that predicts the proper excitation coefficients for the elements of the reflector feed array to compensate the effects of reflector surface distortion. This paper presents the results of an experimental study to verify the above compensation algorithm and in general to demonstrate the effectiveness of the array feed compensation technique.

Zaman, A. J.↗
NASA NTRS1992

A 32-GHz phased array transmit feed for spacecraft telecommunications

A 21-element phased array transmit feed was demonstrated as part of an effort to develop and evaluate state-of-the-art transmitter and receiver components at 32 and 34 GHz for future deep-space missions. Antenna pattern measurements demonstrating electronic beam steering of the two-dimensional array are reported and compared with predictions based on measured performance of MMIC-based phase shifter and amplifier modules and Vivaldi slotline radiating elements.

Lee, K. A.↗
NASA NTRS1991

A high efficiency Ka-band monolithic pseudomorphic HEMT amplifier

A monolithic three-stage Ka-band amplifier has been designed and fabricated on a doped channel heterostructure. Devices with gate length of 0.2 micron and gate width of 50, 100, and 250 micron were cascaded. The gate and drain bias networks were also integrated. The small signal gain is 31 dB and the amplifier is capable of an output power of 190 mW with 23 dB gain and 30.2 percent power added efficiency at 31 GHz. This is a record efficiency for a multistage MMIC at this frequency.

Saunier, Paul↗
NASA NTRS1991

System-level integrated circuit (SLIC) development for phased array antenna applications

A microwave/millimeter wave system-level integrated circuit (SLIC) being developed for use in phased array antenna applications is described. The program goal is to design, fabricate, test, and deliver an advanced integrated circuit that merges radio frequency (RF) monolithic microwave integrated circuit (MMIC) technologies with digital, photonic, and analog circuitry that provide control, support, and interface functions. As a whole, the SLIC will offer improvements in RF device performance, uniformity, and stability while enabling accurate, rapid, repeatable control of the RF signal. Furthermore, the SLIC program addresses issues relating to insertion of solid state devices into antenna systems, such as the reduction in number of bias, control, and signal lines. Program goals, approach, and status are discussed.

Shalkhauser, K. A.↗
NASA NTRS1993

High-efficiency high-gain monolithic heterostructure FET amplifier at 31 GHz

A three-stage heterostructure FET monolithic amplifier has achieved a power-added efficiency of 36 percent with 200 mW output and 18 dB gain at 31 GHz. At a higher drain voltage, the output power increases to 280 mW (with 17.5 dB gain and 31 percent PAE) at a power density of 0.7 W/mm. The MMIC chip measures 2.63 x 1.35 sq mm and requires only a single drain bias and a single gate bias.

Tserng, H. Q.↗
NASA NTRS1994

Optoelectronic Receiver For Communication And Control

Many operational and diagnostic features integrated into circuit chip. GaAs-based integrated circuit designed to serve as optoelectronic interface in phased-array antenna. Intended function to receive digital control signals transmitted on optical fiber and to convert signals to electronic control signals, which then applied to monolithic microwave integrated circuit (MMIC). Also used in reception of high-rate optical digital communications within computers, between computers, and in signal-distribution systems in aircraft, automobiles, and ships. Interface circuit represents significant improvement over preexisting interface circuits in that its clock-signal-recovery subcircuit requires little or no preamble for immediate synchronization.

Kunath, Richard↗
NASA NTRS1994

Monolithic Optical-To-Electronic Receiver

Monolithic optoelectronic integrated circuit converts multiplexed digital optical signals into electrical signals, separates, and distributes them to intended destinations. Developed to deliver phase and amplitude commands to monolithic microwave integrated circuits (MMIC's) at elements of millimeter-wave phased-array antenna from single optical fiber driven by external array controller. Also used in distribution of high-data-rate optical communications in local-area networks (LAN's). Notable features include options for optical or electrical clock inputs; outputs for raw data, addresses, and instructions for diagnosis; and optical-signal-detection circuit used to reduce power consumption by 80 percent between data-transmission times. Chip fabricated by processes available at many major semiconductor foundries. Distribution of digital signals in aircraft, automobiles, and ships potential application.

Kunath, Richard↗
NASA NTRS1992

High efficiency low cost monolithic module for SARSAT distress beacons

The program objectives were to develop a highly efficient, low cost RF module for SARSAT beacons; achieve significantly lower battery current drain, amount of heat generated, and size of battery required; utilize MMIC technology to improve efficiency, reliability, packaging, and cost; and provide a technology database for GaAs based UHF RF circuit architectures. Presented in viewgraph form are functional block diagrams of the SARSAT distress beacon and beacon RF module as well as performance goals, schematic diagrams, predicted performances, and measured performances for the phase modulator and power amplifier.

Petersen, Wendell C.↗
NASA NTRS1992

Quartz/fused silica chip carriers

The primary objective of this research and development effort was to develop monolithic microwave integrated circuit (MMIC) packaging which will operate efficiently at millimeter-wave frequencies. The packages incorporated fused silica as the substrate material which was selected due to its favorable electrical properties and potential performance improvement over more conventional materials for Ka-band operation. The first step towards meeting this objective is to develop a package that meets standard mechanical and thermal requirements using fused silica and to be compatible with semiconductor devices operating up to at least 44 GHz. The second step is to modify the package design and add multilayer and multicavity capacity to allow for application specific integrated circuits (ASIC's) to control multiple phase shifters. The final step is to adapt the package design to a phased array module with integral radiating elements. The first task was a continuation of the SBIR Phase 1 work. Phase 1 identified fused silica as a viable substrate material by demonstrating various plating, machining, and adhesion properties. In Phase 2 Task 1, a package was designed and fabricated to validate these findings. Task 2 was to take the next step in packaging and fabricate a multilayer, multichip module (MCM). This package is the predecessor to the phased array module and demonstrates the ability to via fill, circuit print, laminate, and to form vertical interconnects. The final task was to build a phased array module. The radiating elements were to be incorporated into the package instead of connecting to it with wire or ribbon bonds.

Source record↗