Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Reynolds Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Flow and Noise Control in High Speed and High Reynolds Number Jets Using Plasma Actuators

The idea of manipulating flow to change its characteristics is over a century old. Manipulating instabilities of a jet to increase its mixing and to reduce its radiated noise started in the 1970s. While the effort has been successful in low-speed and low Reynolds number jets, available actuators capabilities in terms of their amplitude, bandwidth, and phasing have fallen short in control of high-speed and high Reynolds number jets of practical interest. Localized arc filament plasma actuators have recently been developed and extensively used at Gas Dynamics and Turbulence Laboratory (GDTL) for control of highspeed and high Reynolds number jets. While the technique has been quite successful and is very promising, all the work up to this point had been carried out using small high subsonic and low supersonic jets from a 2.54 cm diameter nozzle exit with a Reynolds number of about a million. The preliminary work reported in this paper is a first attempt to evaluate the scalability of the technique. The power supply/plasma generator was designed and built in-house at GDTL to operate 8 actuators simultaneously over a large frequency range (0 to 200 kHz) with independent control over phase and duty cycle of each actuator. This allowed forcing the small jet at GDTL with azimuthal modes m = 0, 1, 2, 3, plus or minus 1, plus or minus 2, and plus or minus 4 over a large range of frequencies. This power supply was taken to and used, with minor modifications, at the NASA Nozzle Acoustic Test Rig (NATR). At NATR, 32 actuators were distributed around the 7.5 in. nozzle (a linear increase with nozzle exit diameter would require 60 actuators). With this arrangement only 8 actuators could operate simultaneously, thus limiting the forcing of the jet at NATR to only three azimuthal modes m = plus or minus 1, 4, and 8. Very preliminary results at NATR indicate that the trends observed in the larger NASA facility in terms of the effects of actuation frequency and azimuthal modes are similar in both small GDTL and larger NASA jets. However, the actuation authority seems to fall short in the larger jet at higher Mach numbers, resulting in decreased amplitude response compared to the small jet, which is attributed at this point to the lack of sufficient number of actuators. The preliminary results seem also to suggest that amplitude of actuation tones is similar in both the small and larger jets.

Samimy, M.↗
NASA NTRS1983

Iterative PNS method for attached flows with upstream influence

A stable global-iteration procedure is developed by utilizing successive sweeps, from inflow to outflow boundaries, of a parabolized Navier-Stokes code for attached, steady supersonic flow. It is shown that the procedure converges in about ten or fewer iterations, and allows for the upstream influence within the subsonic region of a supersonic boundary layer. An implicit forward difference is employed in the subsonic region to evaluate the pressure-gradient term in the streamwise momentum equation. The pressure-gradient term is normally approximated in standard single-sweep parabolized methods, suppressing the upstream influence. The iterative results obtained demonstrate the validity of the single-sweep method for weak interactions. For hypersonic viscous interaction on a flat plate at a Mach number of 5.8, it is found that the single-sweep method has a small error that vanishes as the Reynolds number of the flow is increased. However, the skin friction has an error of about 10 percent for low Reynolds numbers and for hot wall conditions. The application of this method to laminar two-dimensional flow over weak expansion and compression corners shows that the pressure and skin friction results in the vicinity of the expansion corner compare favorably with a time-dependent Navier-Stokes numerical solution.

Rakich, J. V.↗
NASA NTRS1986

Viscous starting jets

The transient motion which is produced when a viscous incompressible fluid is forced from an initial state of rest is studied. The equations for unsteady particle paths, written in terms of similarity variables, are analyzed as a quasi-autonomous system with the Reynolds number treated as a parameter. By finding and classifying critical points in the system's phase portrait, the flow structure is examined. It is shown that: (1) bifurcations in the phase portrait occur at specific values of the Reynolds number of the flow in question, and (2) the exact solutions of the Stokes equations for the low-Reynolds-number limit contain two critical Reynolds numbers and three distinct states of motion which culminate in the onset of a vortex roll-up.

Cantwell, Brian J.↗
NASA NTRS2002

Discontinuous Galerkin Methods for Turbulence Simulation

A discontinuous Galerkin (DG) method is formulated, implemented, and tested for simulation of compressible turbulent flows. The method is applied to turbulent channel flow at low Reynolds number, where it is found to successfully predict low-order statistics with fewer degrees of freedom than traditional numerical methods. This reduction is achieved by utilizing local hp-refinement such that the computational grid is refined simultaneously in all three spatial coordinates with decreasing distance from the wall. Another advantage of DG is that Dirichlet boundary conditions can be enforced weakly through integrals of the numerical fluxes. Both for a model advection-diffusion problem and for turbulent channel flow, weak enforcement of wall boundaries is found to improve results at low resolution. Such weak boundary conditions may play a pivotal role in wall modeling for large-eddy simulation.

Collis, S. Scott↗
NASA NTRS2010

Assessment of the National Transonic Facility for Laminar Flow Testing

A transonic wing, designed to accentuate key transition physics, is tested at cryogenic conditions at the National Transonic Facility at NASA Langley. The collaborative test between Boeing and NASA is aimed at assessing the facility for high-Reynolds number testing of configurations with significant regions of laminar flow. The test shows a unit Reynolds number upper limit of 26 M/ft for achieving natural transition. At higher Reynolds numbers turbulent wedges emanating from the leading edge bypass the natural transition process and destroy the laminar flow. At lower Reynolds numbers, the transition location is well correlated with the Tollmien-Schlichting-wave N-factor. The low-Reynolds number results suggest that the flow quality is acceptable for laminar flow testing if the loss of laminar flow due to bypass transition can be avoided.

Crouch, Jeffrey D.↗
NASA NTRS1989

Investigation of CAST-10-2/DOA 2 airfoil in NAE high Reynolds number two-dimensional test facility

A common airfoil model with the CAST 10-2/DOA-2 profile and 228 mm (9 inches) chord length was tested. The tests performed in NAE covered the Mach numbers from 0.3 to 0.8 and Reynolds numbers from 10 to 30 million. The model was tested with transition free and with transition fixed at 5 percent chord for both the upper and the lower surfaces. The data obtained were analyzed for the effects of Reynolds number, transition fixing and Mach number. The role of the boundary layer on the displacement effect, the interaction with the shock wave and the trailing edge separation are examined. The results are summarized as follows: (1) the airfoil performance depends strongly on Reynolds number and transition fixing; (2) with transition fixed, the aerodynamic quantities such as lift, pitching moment and drag show a monotonic variation with Reynolds number; (3) with transition free, the aerodynamic quantities vary less regularly with Reynolds number and a slight parametric dependency is shown. The weak dependency is due to the compensatory effect of the forward shift of the transition position and the thinning of the turbulent boundary layer as Reynolds number increases; (4) the shock Mach number and the shock position are weakly dependent on Reynolds number; and (5) the long extent of the laminar boundary layer at transonic speeds reduces the drag appreciably at low Reynolds numbers. The drag bucket around the design Mach number can be observed below Reynolds number 15 million.

Chan, Y. Y.↗
NASA NTRS2018

Characterization of Freestream Disturbances in Conventional Hypersonic Wind Tunnels

While low disturbance ("quiet") hypersonic wind tunnels are believed to provide more reliable extrapolation of boundary layer transition behavior from ground to flight, the presently available quiet facilities are limited to Mach 6, moderate Reynolds numbers, low freestream enthalpy, and subscale models. As a result, only conventional ("noisy") wind tunnels can reproduce both Reynolds numbers and enthalpies of hypersonic flight configurations, and must therefore be used for flight vehicle test and evaluation involving high Mach number, high enthalpy, and larger models. This article outlines the recent progress and achievements in the characterization of tunnel noise that have resulted from the coordinated effort within the AVT-240 specialists group on hypersonic boundary layer transition prediction. New Direct Numerical Simulation (DNS) datasets elucidate the physics of noise generation inside the turbulent nozzle wall boundary layer, characterize the spatiotemporal structure of the freestream noise, and account for the propagation and transfer of the freestream disturbances to a pitot-mounted sensor. The new experimental measurements cover a range of conventional wind tunnels with different sizes and Mach numbers from 6 to 14 and extend the database of freestream fluctuations within the spectral range of boundary layer instability waves over commonly tested models. Prospects for applying the computational and measurement datasets for developing mechanism-based transition prediction models are discussed.

Duan, Lian↗
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRS1996

Numerical Simulation of Flow in a Whirling Annular Seal and Comparison With Experiments

The turbulent flow field inside a whirling annular seal was simulated by using SCISEAL, a three-dimensional computational fluid dynamics code. The rotor center described a circular synchronous whirl. A rotating frame transformation was used to make the problem quasi-steady. The flow field at an axial Reynolds number of 24,000 and a Taylor number of 6600 was simulated. The standard kappa-epsilon model with wall functions and the low-Reynolds-number model were used to treat turbulence. An experimentally measured velocity field was used at the inlet boundary. Numerical predictions of the velocities and the stator wall pressures compared well with experimental data. Both turbulence models yielded nearly the same results. The capability of the SCISEAL code to analyze this complex flow field was demonstrated; the isotropic turbulence models performed adequately on this nonisotropic turbulence flow.

Athavale, M. M.↗
NASA NTRS1988

Numerical prediction of flow in slender vortices

The slender vortex approximation was investigated using the Navier-Stokes equations written in cylindrical coordinates. It is shown that, for free vortices without external pressure gradient, the breakdown length is proportional to the Reynolds number. For free vortices with adverse pressure gradients, the breakdown length is inversely proportional to the value of its gradient. For low Reynolds numbers, the predictions of the simplified system agreed well with the ones obtained from solutions of the full Navier-Stokes equations, whereas for high Reynolds numbers, the flow became quite sensitive to pressure fluctuations; it was found that the failure of the slender vortex equations corresponded to the critical condition as identified by Benjamin (1962) for inviscid flows. The predictions obtained from the approximating system were compared with available experimental results. For low swirl, a good agreement was obtained; for high swirl, on the other hand, upstream effects on the pressure gradient produced by the breakdown bubble caused poor agreement.

Reyna, Luis G.↗
NASA NTRS2016

The NASA Juncture Flow Experiment: Goals, Progress, and Preliminary Testing (Invited)

NASA has been working toward designing and conducting a juncture flow experiment on a wing-body aircraft configuration. The experiment is planned to provide validation-quality data for CFD that focuses on the onset and progression of a separation bubble near the wing-body juncture trailing edge region. This paper describes the goals and purpose of the experiment. Although currently considered unreliable, preliminary CFD analyses of several different configurations are shown. These configurations have been subsequently tested in a series of "risk-reduction" wind tunnel tests, in order to help down-select to a final configuration that will attain the desired flow behavior. The risk-reduction testing at the higher Reynolds number has not yet been completed (at the time of this writing), but some results from one of the low-Reynolds-number experiments are shown.

Rumsey, Christopher L.↗
NASA NTRS1988

Experimental investigation of hypersonic aerodynamics

An extensive series of ballistic range tests were conducted at the Ames Research Center to determine precisely the aerodynamic characteristics of the Galileo entry probe vehicle. Figures and tables are presented which summarize the results of these ballistic range tests. Drag data were obtained for both a nonablated and a hypothesized ablated Galileo configuration at Mach numbers from about 0.7 to 14 and at Reynolds numbers from 1000 to 4 million. The tests were conducted in air and the experimental results were compared with available Pioneer Venus data since these two configurations are similar in geometry. The nonablated Galileo configuration was also tested with two different center-of-gravity positions to obtain values of pitching-moment-curve slope which could be used in determining values of lift and center-of-pressure location for this configuration. The results indicate that the drag characteristics of the Galileo probe are qualitatively similar to that of Pioneer Venus, however, the drag of the nonablated Galileo is about 3 percent lower at the higher Mach numbers and as much as 5 percent greater at transonic Mach numbers of about 1.0 to 1.5. Also, the drag of the hypothesized ablated configuration is about 3 percent lower than that of the nonablated configuration at the higher Mach numbers but about the same at the lower Mach numbers. Additional tests are required at Reynolds numbers of 1000, 500, and 250 to determine if the dramatic rise in drag coefficient measured for Pioneer Venus at these low Reynolds numbers also occurs for Galileo, as might be expected.

Intrieri, Peter F.↗
NASA NTRS1947

Summary of Available Data Relating to Reynolds Number Effects on the Maximum Lift Coefficients of Swept-Back Wings

The available foreign and American data relating to Reynolds number effects on the maximum lift coefficients of swept-back wings are summarized and discussed. The data show that at low Reynolds numbers (below about 2.0 x 10(exp 6)) higher maximum lift coefficients were measured in most cases for moderately swept-back wings than for unswept wings of similar plan form; at high Reynolds numbers, however, increasing sweepback resulted in decreasing maximum lift coefficients. A smaller rate of increase of the maximum lift coefficient with Reynolds number was measured for the swept-back wings than for similar unswept wings in the critical range of Reynolds number. Increasing the Reynolds number resulted in decreases in the maximum lift coefficients of the two wings of approximately triangular plan form that were investigated.

Sweberg, Harold H.↗
NASA NTRS1984

Cryogenic wind tunnels for high Reynolds number testing

The evolution and early development of cryogenic wind tunnels is reviewed, and consideration is given to current and future research in cryogenic wind tunnel testing. Emphasis is placed on the problem of low Reynolds numbers in current cryogenic wind tunnel tests as well as flow instability, wall interference and support interference which can inhibit a reliable simulation of complex three-dimensional flows. The operating characteristics of several of the worlds low-speed and high-speed cryogenic wind tunnel testing facilities are presented in the form of several graphs and photographs.

Kilgore, R. A.↗
NASA NTRS1978

High-flying Mini-Sniffer RPV - Mars bound

The Mini-Sniffer is a small unmanned survey aircraft developed by NASA to conduct turbulence and atmospheric pollution measurements from ground level to an altitude of 90,000 ft. Carrying a 25-lb air sampling apparatus, the Mini-Sniffer typically cruises for one hour at 70,000 ft before being remotely piloted back to earth. A hydrazine monopropellant engine powers the craft, while a PCM telemetering system and a radar transponder provide control functions. Development of a high-performance low-Reynolds-number airfoil could make the research craft suitable for a low-altitude terrain-following mission on Mars.

Reed, R. D.↗
DOE OSTI2025

Numerical simulation of flow and mixing in fracture intersections

Fluid transport through fractured geological formations is strongly influenced by the redistribution of solutes at fracture intersections. In this study, we perform detailed numerical simulations of flow and scalar transport within the intersection of two smooth, planar fractures. The analysis focuses on the mixing ratio, the proportion of solute flux exiting along the outlet branch aligned with the primary inlet flow direction, relative to the total solute flux at the outlets. We systematically investigate how the mixing ratio varies with four key parameters: Peclet number, Reynolds number, flow rate ratio between outlet branches, and fracture intersection angle. Results show that the mixing ratio decreases with increasing Peclet number and outlet flow rate ratio, consistent with reduced diffusive spreading and enhanced streamline routing. While low Reynolds numbers have minimal impact, inertial effects at higher Reynolds numbers significantly increase the mixing ratio. Additionally, acute and obtuse intersection angles alter flow partitioning and modify the solute distribution at the outlets. These findings provide a quantitative basis for incorporating physically realistic mixing behavior—intermediate between complete mixing and streamline-following assumptions—into network-scale transport models. The results have direct relevance to subsurface energy systems, including geothermal energy production, carbon sequestration, and contaminant remediation.

58 GEOSCIENCES↗
NASA NTRS1979

Correlation of data related to shock-induced trailing-edge separation and extrapolation to flight Reynolds number

Pressure data from a number of previous wind tunnel and flight investigations of high speed transport type wings were analyzed with the intent of developing a procedure for extrapolating low Reynolds number data to flight conditions. These analyses produced a correlation of the development of trailing-edge separation resulting from increases in Mach number and/or angle of attack and show that scale effects on this correlated separation development and the resulting shock location changes fall into a regular and apparently universal pattern. Further studies appear warranted to refine the correlation through a detailed consideration of boundary layer characteristics, and to evaluate scale effects on supercritical wings.

Cahill, J. F.↗
NASA NTRS1975

Preservation of wing leading edge suction at the plane of symmetry as a factor in wing-fuselage design

Most fuselage geometries cover a portion of the wing leading edge near the plane of symmetry, and it seems reasonable to expect that a large fraction of the leading edge suction which would be developed by the covered wing at high angles of attack is not developed on the fuselage. This is one of the reasons that the Oswald span efficiency factor for the wing body combination fails to approach the value predicted by lifting line theory for the isolated wing. Some traditional and recent literature on wing-body interference is discussed and high Reynolds number data on wing-body-nacelle drag are reviewed. An exposed central leading edge geometry has been developed for a sailplane configuration. Low Reynolds number tests have not validated the design concept.

Larrabee, E. E.↗