Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Effect of crack initiation, stable crack growth and unstable crack propagation on the crack-tip plastic zone

A technique for measuring the plastic zones associated with initial crack-tip yielding, subcritical crack growth, and unstable fracture is discussed. The results of the measurement of the locus of these yield regions, on center-cracked sheet and compact tension specimens of 7075-T6, 7075-T651, and 2024-T3 aluminum, are reported in this paper. It was found that a very accurate representation of the strains was obtained by this method and that the results added significant insight into the fracture process. The plastic zones were found to be approximately eight times wider in 2024-T3 than in the 7075-T6 sheets. The yield zones approached a maximum value after unstable fracture was attained and maintained that size through the fast fracture region. As expected, the plastic zones in the compact tension specimen were associated only with the formation of the shear lips and no plastic zones were observed in the fatigue precracked regions of either the center-cracked or compact-tension specimens.

Poulose, P. K.↗
NASA NTRS1976

Effect of geometry modifications on effectiveness of slot injection in hypersonic flow

The study presents wind-tunnel measurements of surface static pressures, equilibrium temperatures, and skin friction downstream of tangential slot injection into a thick turbulent hypersonic boundary layer from two modified slot configurations. The data are compared with results obtained for baseline configurations reported by Cary and Hefner (1970, 1972) to determine whether simple modifications to the slot configuration can produce improved cooling effectiveness and skin friction reduction. The baseline slot configurations are simply modified by thickening the slot lip and by elevating the location of the slot exit above the flat plate. Although the results indicate that simple modifications of the baseline slot configurations can enhance the skin friction reductions obtained with tangential slot injection, slot base drag estimates show that neither of the modifications will lessen the impact of the systems penalties for collecting, ducting, and injecting the slot air.

Hefner, J. N.↗
NASA NTRS1976

Hollow lunar spherules and microcratering

Craters were generated by micrometer-size, thin-walled hollow glass spheres impacting glass and stainless steel targets to determine morphological features distinguishing craters formed by hollow spheres from those formed by solid projectiles. The craters formed in both targets differed from those formed by solid spherical projectiles in that the central pit is an annular rather than a cup-shaped depression. The existence of an annular crater morphology on a surface exposed to cosmic dust would indicate the presence of thin-walled hollow spherules. Penetrations of thin-walled hollow glass beads by high velocity, solid, micrometer-size spheres are characterized by inward and outward flowing lips showing asymmetries dependent on the angle of impact.

Vedder, J. F.↗
NASA NTRS1976

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow-visualization study has shown that strong Karman vortices develop behind the blunt trailing edge of a plate when the free-stream velocities over both surfaces are equal and that the vortices tend to disappear when the surface velocities are unequal. This observation provides an explanation for the occurence and disappearance of certain discrete tones often found to be present in the noise spectra of coaxial jets. Both the vortex formation and the tones occur at a Strouhal number based on the lip thickness and the average of the external steady-state velocities of about 0.2. Results from theoretical calculations of the vortex formation, based on an inviscid incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Boldman, D. R.↗
NASA NTRS1976

Systematic study of error sources in supersonic skin-friction balance measurements

An experimental study was performed to investigate potential error sources in data obtained with a self-nulling, moment-measuring, skin-friction balance. The balance was installed in the sidewall of a supersonic wind tunnel, and independent measurements of the three forces contributing to the balance output (skin friction, lip force, and off-center normal force) were made for a range of gap size and element protrusion. The relatively good agreement between the balance data and the sum of these three independently measured forces validated the three-term model used. No advantage to a small gap size was found; in fact, the larger gaps were preferable. Perfect element alignment with the surrounding test surface resulted in very small balance errors. However, if small protrusion errors are unavoidable, no advantage was found in having the element slightly below the surrounding test surface rather than above it.

Allen, J. M.↗
NASA NTRS1977

Investigation of normal shock inlets for highly maneuverable aircraft

Concepts are investigated for obtaining both low cowl drag and good inlet performance at high angles of attack. The effect of a canard on inlet performance for a kidney shaped inlet in each of two vertical locations is discussed along with a sharp lip two dimensional inlet on a canardless forebody.

Martin, A. W.↗
NASA NTRS1977

Aerodynamic performance of 0.4066-scale model of JT8D refan stage with S-duct inlet

A scale model of the JT8D refan stage was tested with a scale model of the S-duct inlet design for the refanned Boeing 727 center engine. Detailed survey data of pressures, temperatures, and flow angles were obtained over a range of flows at speeds from 70 to 97 percent of design speed. Two S-duct configurations were tested; one with a bellmouth inlet and the other with a flight lip inlet. The results indicated that the overall performance was essentially unaffected by the distortion generated by the S-duct inlet. The stall weight flow increased by less than 0.5 kg/sec (approximately 1.5% of design flow) with the S-duct inlet compared with that obtained with uniform flow. The detailed measurements indicated that the inlet guide vane (IGV) significantly reduced circumferential variations. For example, the flow angles ahead of the IGV were positive in the right half of the inlet and negative in the left half. Behind the IGV, the flow angles tended to be more uniform circumferentially.

Moore, R. D.↗
NASA NTRS1975

Design and control of a manipulator for tetraplegics

A concept for the design of a manipulator for tetraplegics must be based on the mutual adaptation of system determining properties of the disabled operator, the manipulator, and the environment. Because the reduced capability of tetraplegics allows control of only three degrees of freedom at a time (instead of the normal fifteen), the structure of the environment must be adjusted. A manipulator is described which includes a three dimensional control stick operated by the lips and mouth.

Paeslack, V.↗
NASA NTRS1977

An experimental investigation of a three dimensional wall jet

One and two point statistical properties are measured in the flow fields of a coflowing turbulent jet. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of the circular nozzle; and the resultant effects on the flow field are determined. The one point quantities measured include mean velocities, turbulent intensities, velocity and concentration autocorrelations and power spectral densities, and intermittencies. From the autocorrelation curves, the Taylor microscale and the integral length scale are calculated. Two point quantities measured include velocity and concentration space-time correlations and pressure velocity correlations. From the velocity space-time correlations, iso-correlation contours are constructed along with the lines of maximum maximorum. These lines allow a picture of the flow pattern to be determined. The pressures monitored in the pressure velocity correlations are measured both in the flow field and at the surface of the confining wall(s).

Catalano, G. D.↗
NASA NTRS1977

Study of noise and inflow distortion sources in the NASA QF-1B fan using measured blade and vane pressures

Pressure transducers were installed on the blades and vanes of QF-1B, a transonic-tip-speed fan from the NASA Quiet Fan Program which was tested on the outdoor quiet fan test facility at NASA-Lewis. Signals from the transducers and from far field microphones were analyzed to determine sources of nonuniform inflow and noise. The nonuniform inflow was mostly unsteady with roughly equal contributions from atmospheric turbulence and rig interference. The rig interference was largest at the bottom and appeared to be generated by the support structure which was located behind the inlet lip under the fan. Interaction of this inflow distortion was the dominant source of noise at 1, 2, and 3 times blade passing frequency (BPF) at 60, 70, and 80 percent of design speed. At 90 percent speed, noise at BPF was dominated by the steady rotor field. A broadband spectrum peak centered at about 2.2 times BPF was identified as rotor/stator interaction stemming from a high frequency rotor exit flow component. The remaining broadband energy from 0.3 to 3.5 times BPF was attributed to the better known type of rotor/stator interaction associated with rotor wake turbulence.

Hanson, D. B.↗
NASA NTRS1977

Over-the-wing model thrust reverser noise tests

Static acoustic tests were conducted on a 1/12 scale model over-the-wing target type thrust reverser. The model configuration simulates a design that is applicable to the over-the-wing short-haul advanced technology engine. Aerodynamic screening tests of a variety of reverser designs identified configurations that satisfied a reverse thrust requirement of 35 percent of forward thrust at a nozzle pressure ratio of 1.29. The variations in the reverser configuration included, blocker door angle, blocker door lip angle and shape, and side skirt shape. Acoustic data are presented and compared for the various configurations. The model data scaled to a single full size engine show that peak free field perceived noise (PN) levels at a 152.4 meter sideline distance range from 98 to 104 PNdb.

Goodykoontz, J.↗
NASA NTRS1977

Experimental study of error sources in skin-friction balance measurements

An experimental study has been performed to determine potential error sources in skin-friction balance measurements. A floating-element balance, large enough to contain the instrumentation needed to systematically investigate these error sources has been constructed and tested in the thick turbulent boundary layer on the sidewall of a large supersonic wind tunnel. Test variables include element-to-case misalignment, gap size, and Reynolds number. The effects of these variables on the friction, lip, and normal forces have been analyzed. It was found that larger gap sizes were preferable to smaller ones; that small element recession below the surrounding test surface produced errors comparable to the same amount of protrusion above the test surface; and that normal forces on the element were, in some cases, large compared to the friction force.

Allen, J. M.↗
NASA NTRS1977

Experimental investigations of thrust vectoring systems for VTOL aircraft

This paper presents a summary of two technology programs sponsored by NASA to investigate the characteristics of two thrust vectoring schemes for V/STOL aircraft. The operational capability of the VTOL aircraft is dependent on maximum utilization of the installed thrust in both the cruise and powered lift modes of flight. An effective thrust vectoring system on the cruise propulsion unit is therefore essential to provide maximum payload in hover and STOL plus minimum specific fuel consumption in loiter and cruise. Introducing a high by-pass ratio fan system, augmenting the gas generator thrust, as the propulsion system for VTOL aircraft places increased significance on the performance of the relatively short coupled thrust vectoring systems. The two programs discussed herein include both large-scale and small-scale tests of a vectoring hood system with a vented, internal-lip and swivel nozzle systems. These tests indicated that a satisfactory thrust vectoring system can be developed.

Rolls, L. S.↗
NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets have been used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. Any of the geometric design variables can be analyzed by this technique; but, this paper is restricted to the consideration of the internal lip contraction ratio. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The study will show what value of contraction ratio is required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters.

Boles, M. A.↗
NASA NTRS1977

Aerodynamics of horizontally-opposed aircraft engine installations

The goal of cooling installation design is to provide adequate cooling air flow to the engine with a minimum drag penalty. To achieve this goal, attention must be given to certain aerodynamic factors involved in the design problem. In the present paper, the factors which influence the aerodynamic design of horizontally-opposed engine cooling installations are discussed with particular reference to the performance of the aircraft in terms of the dynamic pressure generated for the power output of the engine, the gains or losses through the propeller, proper inlet design, altitude effects on the orifice characteristics of the engine, and exit area sizing. Results of a flight research program showed that the inlet design has a significant influence on cooling effectiveness and drag; the inlet should be designed for low velocity ratios and should avoid small radii of curvature in its geometry. The influence of the propeller on the inlet appears to cause the stagnation point on the lip to move toward the inside.

Miley, S. J.↗
NASA NTRS1977

Over-the-wing model thrust reverser noise tests

Experimental results are presented for static acoustic tests of a 1/12 scale model over-the-wing target type thrust reverser. The model configuration simulates a design that is applicable to the over-the-wing short-haul advanced technology engine. Aerodynamic screening tests of a variety of reverser designs identified configurations that satisfied a reverse thrust requirement of 35 percent of forward thrust at a nozzle pressure ratio of 1.29. The variations in the reverser configuration included, blocker door angle, blocker door lip angle and shape, and side skirt shape. Acoustic data are presented and compared for the various configurations. The model data scaled to a single full size engine show that peak free field perceived noise levels at a 152.4 meter sideline distance range from 98 to 104 PNdB.

Goodykoontz, J.↗
NASA NTRS1978

Test data report, low speed wind tunnel tests of a full scale lift/cruise-fan inlet, with engine, at high angles of attack

A low speed wind tunnel test of a fixed lip inlet with engine, was performed. The inlet was close coupled to a Hamilton Standard 1.4 meter, variable pitch fan driven by a lycoming T55-L-11A engine. Tests were conducted with various combinations of inlet angle of attack freestream velocities, and fan airflows. Data were recorded to define the inlet airflow separation boundaries, performance characteristics, and fan blade stresses. The test model, installation, instrumentation, test, data reduction and final data are described.

Shain, W. M.↗
NASA NTRS1978

Comparison of the noise characteristics of two low pressure ratio fans with a high throat Mach number inlet

Acoustics data obtained in experiments with two low pressure ratio 50.8 cm (20 in.) diameter model fans differing in design tip speed were compared. Determination of the average throat Mach number used to compare high Mach inlet noise reduction characteristics was based on a correlation of inlet wall static pressure measurements with a flow field calculation. The largest noise reductions were generally obtained with the higher tip speed fan. At a throat Mach number of 0.79, the difference in noise reduction was about 3.5 db with static test conditions. Although the noise reduction increased for the lower tip speed fan with a simulated flight velocity of 41 m/sec (80 knots), it was still about 2 db less than that of the high tip speed fan which was only tested at the static condition. However, variations in acoustic performance could not be absolutely attributed to the different fan designs because of differences in inlet lip contours which resulted in small variations of peak wall Mach number and axial extend of supersonic and near-sonic flow.

Wesoky, H. L.↗