Results for “Laminarization” — Page 17

DOE OSTI2021

Three-Dimensional CFD Investigation of Pre-Spark Heat Release in a Boosted SI Engine

Low-temperature heat release (LTHR) in spark-ignited internal combustion engines is a critical step toward the occurrence of auto-ignition, which can lead to an undesirable phenomenon known as engine knock. As such, correct predictions of LTHR are of utmost importance to improve the understanding of knock and enable techniques aimed at controlling it. While LTHR is typically obscured by the deflagration following the spark ignition, extremely late ignition timings can lead to LTHR occurrence prior to the spark, i.e., pre-spark heat release (PSHR). In this research, PSHR in a boosted direct-injection SI engine was numerically investigated using three-dimensional computational fluid dynamics (CFD). A hybrid approach was used, based on the G-equation model for representing the turbulent flame front and the multi-zone well-stirred reactor model for tracking the chemical reactions within the unburnt region. A recently developed best practice was also employed which keeps the well-stirred reactor model active throughout the entire simulation. This allowed for correct predictions of the previous cycle trapped residuals which have a considerable effect on the onset of LTHR. Multi-cycle simulations were conducted using Co-Optima alkylate and E30 fuels. The predicted in-cylinder pressure and heat release rate agreed well with the experimental data and served as validation for the CFD model. Following the initial validation, the dynamics of PSHR was discussed and a series of parameters of interest were assessed. First, the effect of exhaust valve temperature was investigated, qualitatively highlighting the importance of boundary conditions uncertainty. Further analyses were carried out on the effects of fuel properties, including laminar flame speed (LFS) and heat of vaporization (HOV). The results indicate that PSHR phasing is slightly advanced with lower LFS as more trapped unburnt fuel is made available for the next cycle. A similar trend was observed with lower HOV as less intense spray cooling led to higher mixture temperatures, i.e., higher mixture reactivity. Finally, a comparison of Co-Optima alkylate and E30 fuels was made using the pressure-temperature trajectory framework. It was shown that the differences between Co-Optima alkylate and E30 in PSHR tendency are correlated with both HOV and chemical effects.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

EGR Dilution and Fuel Property Effects on High-Efficiency Spark-Ignition Flames

Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, new engine designs have moved towards increased tumble ratios and stroke-to-bore ratios. Increased tumble ratios correlate positively with increases in turbulent kinetic energy and improved fuel and residual gas mixing, all of which favor faster and more efficient combustion. Longer stroke-to-bore ratios allow higher geometric compression ratios and use of late intake valve closing to control peak compression pressures and temperatures. The addition of dilution to improve efficiency is limited by the resulting increase in combustion instabilities manifested by cycle-to-cycle variability. A number of effects - preferential diffusion, turbulence-combustion interactions, stochastic flow patterns, laminar-turbulent flame kernel transitions, and relative length and velocity scales between flame and turbulence - are believed to be responsible for the increase in cycle-to-cycle variations, where their contributions are likely interlinked. Several studies have shown the influence of stochastic flow characteristics on the nature of combustion instabilities, such as velocity patterns on flame kernel formation and cycle-to-cycle variations in residual gas. However, few have focused on the specific effects of fuel properties. The objective of this work is to contrast the effects of dilution on propane stoichiometric combustion against gasoline. Dilution tolerance experiments were conducted in a purpose-built high stroke-to-bore ratio single cylinder engine with both gasoline and LPG. Three-dimensional full cycle computational fluid dynamics (CFD) simulations employing a level-set combustion approach and Reynolds averaged Navier-Stokes (RANS) turbulence modeling was used to qualitatively assess the changes in length and velocity scales for turbulence and the flame. The experimental results showed that LPG can tolerate higher exhaust gas recirculation (EGR) dilution under a variety of conditions. Analysis of CFD simulations showed that propane flames are likely less sensitive to influences from the flow field due to less thickening of the flame and higher effective flame speeds.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2022

A Study of Propane Combustion in a Spark-Ignited Cooperative Fuel Research (CFR) Engine

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO 2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a sparkignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized. A three-pressure analysis (TPA) model based on the two-zone combustion concept is developed in GT-Power and validated using test results to estimate in-cylinder wall temperatures, residual gas fraction, etc. This model is further utilized to examine end-gas chemistry by enabling the SI turbulent flame combustion and unburned gas chemical kinetics modules. Finally, a three-dimensional (3D) computational fluid dynamic (CFD) model of the CFR engine is developed in CONVERGE, where the G-equation and SAGE detailed chemical kinetics models are implemented for combustion modeling. Here, a 153 species reduced chemical kinetics mechanism derived from the detailed NUIGMech1.1 mechanism based on the ignition delay and laminar flame speed (LFS) studies is used to generate an LFS lookup table and to describe end-gas autoignition chemistry. Multi-cycle Reynolds-averaged Navier-Stokes (RANS) simulations are then performed for the tested CRs, and the numerical model is shown to be capable of predicting the propane combustion characteristics, particularly the end-gas autoignition behavior.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Mapping the performance of a versatile water-based condensation particle counter (vWCPC) with numerical simulation and experimental study

Accurate airborne aerosol instrumentation is required to determine the spatial distribution of ambient aerosol particles, particularly when dealing with the complex vertical profiles and horizontal variations of atmospheric aerosols. A versatile water-based condensation particle counter (vWCPC) has been developed to provide aerosol concentration measurements under various environments with the advantage of reducing the health and safety concerns associated with using butanol or other chemicals as the working fluid. However, the airborne deployment of vWCPCs is relatively limited due to the lack of characterization of vWCPC performance at reduced pressures. Given the complex combinations of operating parameters in vWCPCs, modeling studies have advantages in mapping vWCPC performance. In this work, we thoroughly investigated the performance of a laminar-flow vWCPC using COMSOL Multiphysics® simulation coupled with MATLAB™. We compared it against a modified vWCPC (vWCPC model 3789, TSI, Shoreview, MN, USA). Our simulation determined the performance of particle activation and droplet growth in the vWCPC growth tube, including the supersaturation, $D$ p,kel,0 (smallest size of particle that can be activated), $D$ p,kel,50 (particle size activated with 50 % efficiency) profile, and final growth particle size D d under wide operating temperatures, inlet pressures $P$ (30–101 kPa), and growth tube geometry (diameter $D$ and initiator length $L$ ini ). The effect of inlet pressure and conditioner temperature on vWCPC 3789 performance was also examined and compared with laboratory experiments. The COMSOL simulation result showed that increasing the temperature difference (Δ$T$) between conditioner temperature $T$ con and initiator $T$ ini will reduce $D$ p,kel,0 and the cut-off size $D$ p,kel,50 of the vWCPC. In addition, lowering the temperature midpoint ($T$ mid = $\frac{T_{con}+T_{ini}}{2}$ increases the supersaturation and slightly decreases the $D$ p,kel . The droplet size at the end of the growth tube is not significantly dependent on raising or lowering the temperature midpoint but significantly decreases at reduced inlet pressure, which indirectly alters the vWCPC empirical cut-off size. Our study shows that the current simulated growth tube geometry ($D$=6.3 mm and $L$ ini =30 mm) is an optimized choice for current vWCPC flow and temperature settings. The current simulation can more realistically represent the $D$ p,kel for 7 nm vWCPC and also achieved good agreement with the 2 nm setting. Using the new simulation approach, we provide an optimized operation setting for the 7 nm setting. This study will guide further vWCPC performance optimization for applications requiring precise particle detection and atmospheric aerosol monitoring.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

ExINP NSA Ice Nucleating Particle Concentrations

This data set comprises cumulative ambient ice-nucleating particle (INP) concentrations measured at the National Oceanic and Atmospheric Administration's (NOAA’s) Barrow Atmospheric Baseline Observatory (71.3230° N, 156.6114° W, “BRW” hereafter), next to the Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site and ~ 6 km northeast of the town of Utqiaġvik. Our INP abundance data were generated using a combination of online instrument, the Portable Ice Nucleation Experiment chamber ver. 3 (PINE-03), and an offline cold stage, the West Texas Cryogenic Refrigerator Applied to Freezing Test system (WT-CRAFT). Our online INP data are all from the Examining the Ice-Nucleating Particles from NSA (ExINP-NSA) campaign conducted from October 19, 2021 to May 24, 2024. The offline INP concentration analysis was performed at West Texas A&M University for aerosol particle samples collected on polycarbonate filters (with 0.2-micron diameter pores). The PINE-03 measurements, as well as sampling activities for offline INP measurements, were conducted using the BRW site. An inset laminar sampling stack was mounted to the instrument platform, allowing PINE-03 to intake particle-laden air. For most of the campaign period, the semi-autonomous PINE-03 chamber was remotely controlled from West Texas A&M University using the LabView interface through the BeyondTrust remote-access console. PINE-03 was set to conduct an immersion freezing expansion experiment (i.e., simulated adiabatic cooling along with RHw at or above 100%). Except during the scheduled maintenance periods, the time resolution of each expansion experiment was approximately 12 minutes. PINE-03 continuously measured INP concentrations during the entire campaign without any substantial breaks. For most of the campaign period, PINE scanned its set-point vessel air temperatures from -14 °C to -31 °C and back to -14 °C about every 120 minutes.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

ExINP NSA Ice Nucleating Particle Concentrations

This data set comprises cumulative ambient ice-nucleating particle (INP) concentrations measured at the National Oceanic and Atmospheric Administration's (NOAA’s) Barrow Atmospheric Baseline Observatory (71.3230° N, 156.6114° W, “BRW” hereafter), next to the Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site and ~ 6 km northeast of the town of Utqiaġvik. Our INP abundance data were generated using a combination of online instrument, the Portable Ice Nucleation Experiment chamber ver. 3 (PINE-03), and an offline cold stage, the West Texas Cryogenic Refrigerator Applied to Freezing Test system (WT-CRAFT). Our online INP data are all from the Examining the Ice-Nucleating Particles from NSA (ExINP-NSA) campaign conducted from October 19, 2021 to May 24, 2024. The offline INP concentration analysis was performed at West Texas A&M University for aerosol particle samples collected on polycarbonate filters (with 0.2-micron diameter pores). The PINE-03 measurements, as well as sampling activities for offline INP measurements, were conducted using the BRW site. An inset laminar sampling stack was mounted to the instrument platform, allowing PINE-03 to intake particle-laden air. For most of the campaign period, the semi-autonomous PINE-03 chamber was remotely controlled from West Texas A&M University using the LabView interface through the BeyondTrust remote-access console. PINE-03 was set to conduct an immersion freezing expansion experiment (i.e., simulated adiabatic cooling along with RHw at or above 100%). Except during the scheduled maintenance periods, the time resolution of each expansion experiment was approximately 12 minutes. PINE-03 continuously measured INP concentrations during the entire campaign without any substantial breaks. For most of the campaign period, PINE scanned its set-point vessel air temperatures from -14 °C to -31 °C and back to -14 °C about every 120 minutes.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2019

Magnetoelastically actuated MEMS device and methods for its manufacture

A magnetoelastically actuated device includes a microscale cantilever arm supported at a standoff distance from a substrate. The cantilever arm is formed as a laminar magnetic actuator configured to bend when it is subjected to a magnetic field. The cantilever arm includes a film of magnetostrictive material. Also provided is a method for fabricating the magnetoelastically actuated device. The method includes defining an actuator mold in a layer of photoresist on a structural layer of the cantilever arm and electrodepositing a layer of a magnetostrictive alloy containing cobalt and iron onto the structural layer within the actuator mold.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Experimental and theoretical study of the soot-forming tendencies of furans as potential biofuels

Sustainably-produced biofuels, including furans derived from lignocellulosic biomass, are being studied as potential next-generation fuels. Biofuels have unique structures that are absent in conventional fuels and they potentially emit fewer particulates than conventional fuels because of the presence of oxygen atoms. In this work, we focus on quantification and measurement of sooting tendency. A set of furans was selected and their sooting tendencies were characterized by Yield Sooting Index (YSI), which was obtained by measuring the line-of-sight spectral radiance (LSSR) of a coflow laminar diffusion flame doped with 1000 ppm of each test fuel. The measured YSIs are lower than traditional gasoline fuels and benzenoid aromatics (e.g., YSIbenzene = 100). We also performed numerical simulations with a detailed chemical kinetic mechanism to analyze the flame chemistry of 2-methylfuran (2MF). 4→5 H-atom migration in the furan ring causes 31.0% of the total decomposition and is the dominant fuel consumption pathway leading to soot. DFT calculations via the G4 composite method were carried out to obtain activation energies (Ea) and bond dissociation energies (BDE). The results showed that the 4→5 H-atom migration in the furan ring has the second lowest Ea and subsequently forms a 1,2-diene-substituted ketone derivative as a stable species. The ring-opening products of the 4→5 H-atom migration are propyne + a linear ketene for 2-n-alkylfurans, and 1-butyne + a methyl-substituted ketene for 2-t-butylfuran. These results can explain the trends of the measured YSIs of 2-alkylfurans.

09 BIOMASS FUELS↗

DOE OSTI2020

Sample analysis systems and methods of use thereof

The invention generally relates to sample analysis systems and methods of use thereof. In certain aspects, the invention provides a system for analyzing a sample that includes an ion generator configured to generate ions from a sample. The system additionally includes an ion separator configured to separate at or above atmospheric pressure the ions received from the ion generator without use of laminar flowing gas, and a detector that receives and detects the separated ions.

42 ENGINEERING↗

DOE OSTI2021

A Multiscale Modeling Approach to Cryocompressed Hydrogen Storage Pressure Vessels – Part II: Constitutive Modeling and Finite Element Analysis

Subjected to thermomechanical cycling, composite cryogenic hydrogen (H2) storage pressure vessels experience high stresses in the carbon fiber (CF)/epoxy overwrap which can lead to vessel failure due to a combination of degradation mechanisms such as matrix cracking, fiber/matrix debonding, delamination, and fiber rupture. The present paper is the second part of a set of two articles on this subject that addresses analysis and design of these pressure vessels. Predictive finite element (FE) modeling capabilities have been used to support a material acceptance process that aims at providing guidance to evaluate specialty resins, vessel liner options, and CF composites through thermomechanical testing. We have applied a multiscale modeling approach recently developed (B.N. Nguyen et al., International Journal of Hydrogen Energy, 2019, https://doi.org/10.1016/j.ijhydene.2019.09.200) to perform three-dimensional (3D) FE analysis and design of a cryo-compressed H2 storage pressure vessel for its operation in a large temperature range from room to cryogenic temperatures. The developed approach termed the micro-meso-macro approach determines the laminar stresses in different layers of the vessel in addition to constituent (i.e., fiber and matrix) stresses that are important to the design of the composite overwrap for its layup and material combination to reduce the risk of vessel failure.

Nguyen, Ba Nghiep↗

DOE OSTI2021

Radiative Heat Transport and Optical Characterization of High Temperature Molten Salts

The goal of this project was to advance the field of molten fluoride radiative heat transfer (RHT), through optical property measurements, heat transfer loop construction and operation, and computational fluid dynamics simulations. The following outcomes have been accomplished. A comprehensive review has been conducted to compile all available RHT-relevant optical absorption data for molten fluorides. The various measurement methods have also been compiled and critiqued. Thermal emission measurement methods have been refined and documented. A unique thermal emissivity measurement facility has been constructed and used to measure the emissivity of flowing FLiBe-exposed SS316 samples. A slight increase has been observed in the emissivity compared to unexposed SS316. A dual reflectance-emission setup was partially demonstrated for the purpose of molten fluoride absorption measurement. Preliminary infrared edge data for FLiNaK was obtained. A visible near-infrared (NIR) measurement setup has been constructed and will be used to measure absorption of corrosion products in FLiBe. A new multi-band thermal radiation method using blackbody-weighted spectral bands for the absorption-coefficient was deployed to investigate the thermal performance of the UW Natural Circulation FLiBe Loop under various power levels and operating conditions. The results showed an increasing and decreasing trend in the overall heat transfer with optical thickness with a maximum at optical thickness τ D ≈Ο(1). A forced convection FLiBe loop was constructed for the purpose of studying corrosion and thermal hydraulic phenomena. A vertical cantilever pump is used to achieve up to 5 gpm and 5 m/s flow velocity in hot and cold test sections. A methodology has been established for modeling radiative heat transfer (RHT) in molten salt coolants for the purpose of quantifying the contribution of thermal radiation in conditions relevant to FHR or MSR systems. The comparison between the results obtained for forced and mixed convection showed that in the studied ranges of optical thickness, the maximum effect of RHT on overall heat transfer was 60% improvement observed at z/D = 250 for forced convection; whereas for mixed convection, that value was higher at 170% observed at z/D = 30. The highest effect of RHT on the overall energy distribution was observed at τ D ≈3.4. Negligible effect (<20%) was observed above τ D =18 and below τ D ≈0.002. A CFD code-to-code comparison was conducted using COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT, for a forced and mixed convection laminar flow for a grey medium in a vertical heated using both COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT. The relative error was the largest at τ D =40 for the radiative heat flux, bulk temperature, and Nusselt number. On the other hand, the relative error was the least at τ D =0.002 for the conductive heat flux, bulk temperature, and Nusselt number.

Anderson, Mark↗

DOE OSTI2022

Simulations of Low Mach Number Reactive Flows Coupled with Electric Fields

Applying electric fields to flames can provide an effective, non-invasive control of the combustion process. In this work, an algorithm recently introduced to handle the interactions between reactive flows and an electric field is extended to handle multiple dimensions and adaptive mesh refinement (AMR), and applied to a series of laminar flames. Experimental data allows to validate the ability of the algorithm to capture the mechanisms driving the flame response to electric fields.

electric fields↗

DOE OSTI2022

Simulations of Low Mach Number Reactive Flows Coupled with Electric Fields: Preprint

Applying electric fields to flames can provide an effective, non-invasive control of the combustion process. In this work, an algorithm recently introduced to handle the interactions between reactive flows and an electric field is extended to handle multiple dimensions and adaptive mesh refinement (AMR), and applied to a series of laminar flames. Experimental data allows to validate the ability of the algorithm to capture the mechanisms driving the flame response to electric fields.

electric field↗

DOE OSTI2023

An Assessment of Kinetic Models for Ammonia Flame Extinction

The growing interest in using ammonia as a carbon-neutral replacement fuel has prompted numerous recent research efforts towards understanding fundamental combustion characteristics and chemical kinetics of ammonia oxidation. Despite these recent efforts, there remains a large deficiency in extinction limit data for ammonia flames, particularly under elevated pressure and temperature conditions relevant to gas turbines. Even the literature reaction mechanisms developed specifically for ammonia have been untested under gas turbine relevant conditions, and existing kinetic models have shown large variations in laminar flame speed, extinction strain rate, and speciation predictions for NH3–H2 mixtures at ambient conditions. Recent work by Thomas and co-workers, for example, compared different ammonia kinetic models in the literature for predicting their extinction strain rate measurements for non-premixed NH3-H2 counterflow flames, and again have highlighted the discrepancies in model predictions. Here, our work has undertaken to further highlight important reaction pathways for ammonia oxidation that may be responsible for these discrepancies for extinction strain rate predictions, as well as elucidate sensitive reaction steps with large uncertainties that require further attention. This work points to a need for an improved understanding of ammonia combustion chemistry as well as new datasets at elevated pressure and temperature conditions to better constrain rate expressions for key reaction steps.

ammonia, flame, combustion, kinetic, kinetics↗

DOE OSTI2023

EXPERIMENTAL AND COMPUTATIONAL STUDY OF DIRECT CONTACT MEMBRANE DISTILLATION

Experimental and computational studies of direct contact membrane distillation (DCMD) are conducted. The permeate flux is measured in a module containing a flat sheet membrane. Polytetrafluoroethylene (PTFE) hydrophobic membrane (Membrane Solutions, FPB045A16) with a nominal pore size of 0.45 μm, the thickness of 179~239 μm, the porosity of 80% is used in the experiments. The feed solution is a binary mixture of water and NaCl. The inlet feed temperature is fixed at 70°C, and the feed Reynolds number is varied between 500 and 2000. Two inlet feed concentrations, 0 and 35g/L, are considered. The permeate flow rate was kept constant at Re of 1300 and temperature of 20°C. Three-dimensional steady-state computational fluid dynamics (CFD) simulations are performed using the laminar model. The Navier’s Stokes, energy, and mass transport equations in each channel coupled with flux boundary conditions imposed at the membrane surface are solved. The predicted module-averaged flux is compared to measured data for all operating conditions. Measured and predicted flux agrees well; validating both experiments and model, Temperature polarization in the feed and permeate channel and concentration polarization in the feed channel are characterized by validated CFD simulations.

Oztekin, Alparslan↗

DOE OSTI2023

Evaluating Scaling Effects of Steam Condensation Physics-based Model for Small Modular Reactor

This study focused on assessing condensation heat transfer (CHT) models for enhancing the passive safety of small modular reactors (SMRs). It also encompassed a review of the theoretical and semi-theoretical CHT models and correlations. Condensation models such as the degradation factor, heat and mass transfer analogy (HMTA), and boundary layer models are used to study advanced nuclear reactor PCCS. The previous CHT models were developed for small tube geometries, which differ from the containment of SMR. This study examined the scaled relations of a physics-based CHT model for analyzing laminar and turbulent film condensation downward flow conditions inside scaled tube geometries.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

Presentation: Evaluating scaling effects of steam condensation physics-based model for small modular reactors safety

This study focused on assessing condensation heat transfer (CHT) models for enhancing the passive safety of small modular reactors (SMRs). It also encompassed a review of the theoretical and semi-theoretical CHT models and correlations. Condensation models such as the degradation factor, heat and mass transfer analogy (HMTA), and boundary layer models are used to study advanced nuclear reactor PCCS. The previous CHT models were developed for small tube geometries, which differ from the containment of SMR. This study examined the scaled relations of a physics-based CHT model for analyzing laminar and turbulent film condensation downward flow conditions inside scaled tube geometries.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

Apparatus for a laser welding system

A laser welding system for welding a component and reducing defects in the weld by ensuring uniform, laminar gas flow over a process area of the system. The laser welding system comprises a laser for welding the component, a platform for supporting the component, an enclosure surrounding the platform, a first actuatable barrier, a second actuatable barrier, an actuator, and a controller. The enclosure includes a plurality of walls, one of the walls having an inlet and another wall having an outlet. The inlet and outlet each having an opening having a cross-sectional area for letting gas flow through. The first and second barriers are configured to modify the cross-sectional areas of the openings when actuated. The actuator is configured to actuate the barriers, and the controller is configured to direct the actuator to actuate the barriers so that the cross-sectional area of the first opening is larger than the cross-sectional area of the second opening so that a pressure at the inlet is greater than a pressure at the outlet.

Sartin, Bryan↗