SEARCH · Engineering Papers

Results for “LOSSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2023

Differential Saccade-Pursuit Coordination Under Sleep Loss and Low-Dose Alcohol

Introduction: Ocular tracking of a moving object requires tight coordination between smooth pursuit and saccadic eye movements. Normally, pursuit drives gaze velocity to closely match target velocity, with residual position offsets corrected by catch-up saccades. However, how/if common stressors affect this coordination is largely unknown. This study seeks to elucidate the effects of acute and chronic sleep loss, and low-dose alcohol, on saccade-pursuit coordination, as well as that of caffeine. Methods: We used an ocular tracking paradigm to assess three metrics of tracking (pursuit gain, saccade rate, saccade amplitude) and to compute “ground lost” (from reductions in steady-state pursuit gain) and “ground recouped” (from increases in steady-state saccade rate and/or amplitude). We emphasize that these are measures of relative changes in positional offsets, and not absolute offset from the fovea. Results: Under low-dose alcohol and acute sleep loss, ground lost was similarly large. However, under the former, it was nearly completely recouped by saccades, whereas under the latter, compensation was at best partial. Under chronic sleep restriction and acute sleep loss with a caffeine countermeasure, the pursuit deficit was dramatically smaller, yet saccadic behavior remained altered from baseline. In particular, saccadic rate remained significantly elevated, despite the fact that ground lost was minimal. Discussion: This constellation of findings demonstrates differential impacts on saccade-pursuit coordination with low-dose alcohol impacting only pursuit, likely through extrastriate cortical pathways, while acute sleep loss not only disrupts pursuit but also undermines saccadic compensation, likely through midbrain/brainstem pathways. Furthermore, while chronic sleep loss and caffeine-mitigated acute sleep loss show little residual pursuit deficit, consistent with uncompromised cortical visual processing, they nonetheless show an elevated saccade rate, suggesting residual midbrain and/or brainstem impacts.

smooth pursuit↗

NASA NTRSDate not supplied

Deletion of Cdkn1a in Mice Rescues Reduced Osteogenesis in Microgravity and Increases Coupled Osteoclastic Bone Degenerative Activity and Bone Loss

Elevated Cdkn1a/p21 levels in mouse bone during spaceflight have led us to hypothesize that this cell cycle inhibitor could regulate osteogenesis in response to mechanical unloading in microgravity. Cdkn1a interacts with cyclins CDK1/2/4,6 during G1 and S phases, and suppression of its expression by mechanical stretch enhances proliferation and mineralization in osteoblastic cell cultures. To test this hypothesis in a whole-organism model, we used C57BL/J6 WT/Cdkn1a-null mice in the NASA RR-10, 30-day ISS microgravity experiment. To quantify active mineralization in microgravity mice were injected with Calcein seven and two days before euthanasia on-orbit, followed by high-resolution confocal imaging of optically cleared femoral endosteal surfaces. To quantify cortical and cancellous bone parameters we conducted microCT analyses of the femur and tibia. Confocal imaging revealed a population of mineralizing calcein-positive single osteoblasts, and multicellular surfaces of mineralization by osteocytes in lacunae. The Cdkn1a-null genotype shows a greater ratio of early-osteoblasts to late-osteocytes and reduced mineralization versus WT. Additionally, in microgravity WT bones have a large (80%) decrease in active mineralization, but remarkably Cdkn1a deletion fully rescued mineralized surface loss. MicroCT shows trends for moderate spaceflight bone loss in WT femurs, and significant losses in the tibia, while Cdkn1a-null femurs showed much larger significant tissue losses, including 25% thinner trabeculae (p < 0.01),40% thinner cortical bone (p < 0.005), and 10% lower percent cortical bone area (p < 0.05). These results indicate that endogenous bone Cdkn1a plays a key role in mechanosensitive downregulation of osteoprecursor proliferation and promotes osteocytic differentiation. In microgravity however, while Cdkn1a deletion rescues mineralization, bone loss quantified by microCT is greatly increased, likely due to the molecular coupling of osteogenesis and osteoclastogenesis. This molecular mechanism opens the possibility for potential pharmacological approaches to mitigate bone loss in space simultaneously targeting Cdkn1a and osteoclast inhibition.

Eduardo A.C. Almeida↗

DOE OSTI2019

Bifacial PV System Mismatch Loss Estimation & Parameterization

Non-uniform irradiance on the rear-side of bifacial PV systems can cause additional mismatch loss which may not be appropriately captured in PV energy production estimates and software. We have evaluated several rooftop mounted systems over high albedo reflective roofs. Mismatch losses of up to 2% annual loss for very close-mounted (0.15 m) rooftop systems were found, but losses for high ground-clearance rooftop systems were lower (<0.5%). A simplified empirical relationship was found that links the spatial variation of irradiance (specifically the mean absolute difference of irradiance) to the resulting mismatch loss factor, with a R2 fit better than 0.985. This approximate relationship has been validated by experiments on mismatched PV modules, and provides a basis for fast estimation of bifacial mismatch loss factors for use in hourly PV performance simulations such as PVSyst or SAM.

14 SOLAR ENERGY↗

DOE OSTI2019

Bifacial PV System Mismatch Loss Estimation and Parameterization: Preprint

Non-uniform irradiance on the rear-side of bifacial PV systems can cause additional mismatch loss which may not be appropriately captured in PV energy production estimates and software. We have evaluated several scenarios including horizontal single-axis tracking (HSAT) and rooftop mounted systems over high albedo reflective roofs. Mismatch losses of up to 2% annual loss for very close-mounted (0.15 m) rooftop systems were found, but losses for HSAT systems and high ground-clearance rooftop systems were lower (<0.5%). A simplified empirical relationship was found that links the spatial variation of irradiance (specifically the mean absolute difference of irradiance) to the resulting mismatch loss factor, with a R2 fit better than 0.985. This approximate relationship has been validated by experiments on mismatched PV modules, and provides a basis for fast estimation of bifacial mismatch loss factors for use in hourly PV performance simulations such as PVSyst or SAM.

14 SOLAR ENERGY↗

DOE OSTI2025

Wellbore Stability and Mud Loss Management in Geothermal Drilling: Optimizing Mud Weight to Mitigate Tensile Wellbore Fracturing at The Geysers, California

As part of a U.S. Department of Energy (DOE) Geothermal Technologies Office-funded initiative, Geysers Power Company, LLC, a subsidiary of Calpine Corporation, has been working to enhance drilling performance at the world’s largest geothermal field, The Geysers, in northern California. In a recent drilling operation of the GDC-36 well, excessive mud losses were encountered, initially addressed through repeated but largely ineffective cement plugging. Ultimately, the most effective strategy was to drill blind through the loss zones, made feasible by the high rate of penetration (ROP) achieved with PDC bits, allowing significant progress before the mud tanks were depleted and water-sensitive argillic formation layers could collapse. In response to these challenges, the project team explored alternative methods to minimize downtime and risks associated with cement plugging and continuous mud loss and to contemplate the driving mechanisms for the losses. Wellbore imaging using Formation MicroImager (FMI) and Ultrasonic Borehole Imager (UBI) tools revealed longitudinal tensile fractures, which were attributed to mud weights exceeding the minimum circumferential stress resulting from the native stress field and formation pressure. This study examines the mud losses encountered and leverages wellbore imaging data to understand the mechanisms behind mud induced tensile fracturing in specific rock facies. Understanding fracture behavior across different lithologies is crucial, as fractures within the reservoir can enhance steam migration throughout the system. The reservoir at The Geysers lies within the Mesozoic Franciscan Assemblage, a tectonic mélange formed by subduction. It consists of metamorphosed turbidite sandstone (greywacke) and mudstone (argillite), oceanic upper crust (including greenstone and chert), and serpentinized ultramafic rocks - each exhibiting distinct geomechanical fracturing properties. The structural fabric of the Franciscan Assemblage was shaped by low-angle Mesozoic thrust faulting and later overprinted by sub-vertical strike-slip structures related to the Pacific-North American plate boundary. A wellbore stability model was developed using core measurements and logs to simulate fracturing scenarios during drilling under varying stress conditions. These simulations guided the development of an optimized mud weight management strategy that should enable adaptive adjustments during drilling, reducing the likelihood of tensile fracturing and mud losses, ultimately improving operational efficiency.

15 GEOTHERMAL ENERGY↗

DOE OSTI2026

Quality and Loss Factor Characterization of YBCO Superconducting Transmission Lines for Axion Dark Matter Detection

Axion haloscope experiments aim to detect the conversion of axions into microwave photons under a strong magnetic field through resonant cavity techniques. The conversion produces an extremely small signal, requiring a cryogenic environment to reduce thermal noise, and low-loss superconducting transmission lines for minimal attenuation in the readout chain. Yttrium barium copper oxide (YBCO) cables are a promising candidate. Unlike commonly used low-loss cryogenic cables such as niobium (Nb) and niobium titanium (NbTi), which have low critical fields, YBCO is a high-temperature superconductor that can remain stable in strong magnetic fields. We characterized the quality and loss of five stripline resonators from the Brookhaven Technology Group: three YBCO, a copper reference, and a silver reference. Experimental methodology included collecting scattering parameter data on a vector network analyzer for the samples at 77 K along with room temperature baseline measurements, and employing both Lorentzian-fit and circle-fitting techniques to confirm the coupling regime and corroborate results. We achieved quality factors on the order of $10^3$ with corresponding loss factors on the order of $10^{-1}$ dB/m. Trends were comparable with literature data on Nb and NbTi at 4 K, which did have lower loss under these conditions, but suggested similar or perhaps better loss for YBCO when accounting for the temperature difference. We also developed a cryogenic probe for future measurements in a 14 T applied field at 30 mK. This will serve to directly evaluate YBCO's durability in magnetic fields, and we expect significantly improved performance at millikelvin temperatures.

Marinos, Z. [UCLA]↗

DOE OSTI2021

Levenberg–Marquardt multi-classification using hinge loss function

Incorporating higher-order optimization functions, such as Levenberg-Marquardt (LM) have revealed better generalizable solutions for deep learning problems. However, these higher-order optimization functions suffer from very large processing time and training complexity especially as training datasets become large, such as in multi-view classification problems, where finding global optima is a very costly problem. To solve this issue, we develop a solution for LM-enabled classification with, to the best of knowledge first-time implementation of hinge loss, for multiview classification. Hinge loss allows the neural network to converge faster and perform better than other loss functions such as logistic or square loss rates. Here we prove our method by experimenting with various multiclass classification challenges of varying complexity and training data size. The empirical results show the training time and accuracy rates achieved, highlighting how our method outperforms in all cases, especially when training time is limited. Our paper presents important results in the relationship between optimization and loss functions and how these can impact deep learning problems.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2019

Continuous Wave Resonant Photon Stimulated Electron Energy-Gain and Electron Energy-Loss Spectroscopy of Individual Plasmonic Nanoparticles

The unique optical properties of surface plasmon resonances in nanostructured materials have attracted considerable attention, broadly impacting both fundamental research and applied technologies ranging from sensing and optoelectronics to quantum computing. Electron energy-loss spectroscopy (EELS) in the transmission electron microscope has revealed valuable information about the full plasmonic spectrum of these materials with nanoscale spatial resolution. Here, in this study, we report a novel approach for experimentally accessing the photon-stimulated electron energy-gain and stimulated electron energy-loss responses of individual plasmonic nanoparticles via the simultaneous irradiation of a continuous wave laser and continuous current, monochromated electron probe. Stimulated gain and loss probabilities are equivalent and increase linearly in the low-irradiance range of 0.5 × 10 8 to 4 × 10 8 W/m 2 , above which excessive heating reduces the observed probabilities; importantly in our low-irradiance regime, the photon energy must be tuned in resonance with the plasmon energy for the stimulated gain and loss peaks to emerge. Theoretical modeling based on Fermi’s golden rule elucidates how the plasmon resonantly and coherently shuttles energy quanta between the electron probe and the radiation field and vice versa in stimulated electron energy-loss and -gain events. This study opens a fundamentally new approach to explore the quantum physics of excited-state plasmon resonances that does not rely on high-intensity laser pulses or any modification to the EELS detector.

(scanning) transmission electron microscope ((S)TE↗

DOE OSTI2016

Regional Soiling Stations for PV: Soling Loss Analysis

The soiling loss factor (SLF) of photovoltaic (PV) modules/system is an interplay between the dust frequency and intensity of the site, rain frequency and intensity of the site, tilt angle and height of the module installation, and wind speed and humidity of the site. The integrated area of the downward peaks of the SLF time series plots for a year provides the annual soiling loss for the system at each tilt angle. Sandia National Laboratories, in collaboration with Arizona State University, installed five regional soiling stations around the country and collected soiling loss data over a year. Four of these soiling stations are located at the U.S. Department of Energy Regional Test Centers (Florida, Albuquerque, Colorado and Vermont), while the fifth station is located at the Arizona State University Photovoltaic Reliability Lab (Arizona). This paper presents an analysis on the SLF for each test site at ten different tilt angles. Based on the analysis of a yearlong data obtained in 2015, it appears to indicate that the Arizona site experienced the highest annual soiling loss with a significant dependence on the tilt angle while the other four sites experienced a negligibly small annual soiling loss with practically no dependence on the tilt angle.

14 SOLAR ENERGY↗

DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗

DOE OSTI2021

International collaboration framework for the calculation of performance loss rates: Data quality, benchmarks, and trends (towards a uniform methodology)

Abstract The IEA PVPS Task 13 group, experts who focus on photovoltaic performance, operation, and reliability from several leading R&D centers, universities, and industrial companies, is developing a framework for the calculation of performance loss rates of a large number of commercial and research photovoltaic (PV) power plants and their related weather data coming across various climatic zones. The general steps to calculate the performance loss rate are (i) input data cleaning and grading; (ii) data filtering; (iii) performance metric selection, corrections, and aggregation; and finally, (iv) application of a statistical modeling method to determine the performance loss rate value. In this study, several high‐quality power and irradiance datasets have been shared, and the participants of the study were asked to calculate the performance loss rate of each individual system using their preferred methodologies. The data are used for benchmarking activities and to define capabilities and uncertainties of all the various methods. The combination of data filtering, metrics (performance ratio or power based), and statistical modeling methods are benchmarked in terms of (i) their deviation from the average value and (ii) their uncertainty, standard error, and confidence intervals. It was observed that careful data filtering is an essential foundation for reliable performance loss rate calculations. Furthermore, the selection of the calculation steps filter/metric/statistical method is highly dependent on one another, and the steps should not be assessed individually.

14 SOLAR ENERGY↗

DOE OSTI2022

Testing Low-Loss Microstrip Materials with MKIDs for Microwave Applications

Future measurements of the millimeter-wavelength sky require a low-loss superconducting microstrip, typically made from niobium and silicon-nitride, coupling the antenna to detectors. Here, we propose a simple device for characterizing these low-loss microstrips at 150 GHz. In our device we illuminate an antenna with a thermal source and compare the measured power at 150 GHz transmitted down microstrips of different lengths. The power measurement is made using Microwave Kinetic Inductance Detectors (MKIDs) fabricated directly onto the microstrip dielectric, and comparing the measured response provides a direct measurement of the microstrip loss. Our proposed structure provides a simple device (4 layers and a DRIE etch) for characterizing the dielectric loss of various microstrip materials and substrates. We present initial results using these devices. We demonstrate that the millimeter wavelength loss of microstrip lines, a few tens of millimeters long, can be measured using a practical aluminum MKID with a black body source at a few tens of Kelvin.

47 OTHER INSTRUMENTATION↗

DOE OSTI2019

Influence of AC Loss on Stress and Strain of Superconducting Coils

The second-generation (2G) high-temperature superconducting (HTS) coated conductors (CC) are increasingly used in power systems recently, especially in large-capacity superconducting magnetic energy storage (SMES). HTSCC in superconducting energy storage coil is subjected to thermal stress which is caused by thermal contraction due to AC loss. The thermal stress will degrade the critical currents and may cause the displacement of the superconducting coil and insulating epoxy resin. In this work, the AC loss of the superconducting coil is firstly obtained by finite element method (FEM) software COMSOL with the method of iterative conductivity. Furthermore, the effect of AC loss on the superconducting coil is thus analyzed by solving the coupling problems which include magnetic field, mechanical behaviors, and heat transfer in solids. The result shows that the AC loss of the superconducting coil is concentrated in the middle of the coil and the maximum AC loss density is 5.96 × 10{sup 5} W/m{sup 3}; the maximum stress laid at the inner radius of the coil and the maximum stress is 0.01 MPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Novel artificial neural network model for instantaneous power losses and operational efficiency mapping of MW-scale vanadium redox flow battery for improved technoeconomic analysis

A novel data-driven, machine-learning-based method for modeling the instantaneous power losses of a distribution-sited 2 MW/8MWh vanadium redox flow battery (VRFB), a grid-scale electrochemical storage technology, is introduced and compared against benchmark empirical modeling approaches, including symmetric and asymmetric models, as well as a recent convex hull modeling approach. The novel loss modeling method introduces several advantages over the benchmark models and over simplistic efficiency estimates, the most significant of which is that the model can accurately reflect the stepwise and non-linear parasitic losses associated with the duty cycles of mechanical auxiliary systems like pump motor drives and blower fans. Residuals of the models are compared; the proposed data driven model features significantly improved accuracy over the benchmark models. The model's coefficient of determination is also improved relative to that of the benchmark models. Furthermore, a novel method for visualization of operational efficiency of the grid-scale storage technology is introduced. To demonstrate the benefits of the novel data-driven method for modeling the VRFB, the benchmark models and the proposed models are embedded into an Open DSS distribution network model to study two applications of the grid-scale electrical storage system: load leveling for grid support and energy arbitrage. This article demonstrates that the accuracy of the instantaneous power loss model significantly impacts the understanding of the state of charge of the VRFB. In turn, the accuracy of the efficiency modeling of the VRFB impacts the understanding of the potential economic value and technical benefits to the distribution network operators. In conclusion, the presented power loss modeling approach is, therefore, highly relevant for utility-stakeholders, battery asset owners, system engineers, system designers, and financial planners interested in evaluating or optimizing the operation of grid-scale VRFBs.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

Electronic energy loss and ion velocity correlation effects in track production in swift-ion-irradiated LiNbO3: A quantitative assessment between structural damage morphology and energy deposition

The primary motivation for studying how irradiation modifies the structures and properties of solid materials involves the understanding of undesirable phenomena, including irradiation-induced degradation of components in nuclear reactors and space exploration, and beneficial applications, including material performance tailoring through ion beam modification and defect engineering. In this work, the formation mechanism of latent tracks with different damage morphologies in LiNbO 3 crystals under 0.09–6.17 MeV/u ion irradiation with an electronic energy loss from 2.6–13.2 keV/nm is analyzed by experimental characterizations and numerical calculations. Irradiation-induced damage is preliminarily evaluated via the prism coupling technique to analyze the correlation between the dark-mode spectra and energy loss profiles of irradiated regions. Under the irradiation conditions of different ion velocities and electronic energy losses, different damage morphologies, from individual spherical defects to discontinuous and continuous tracks, are experimentally characterized. During ion penetration process, the ion velocity determines the spatiotemporal distribution of deposited irradiation energy induced by electronic energy loss, meaning that the two essential factors including electronic energy loss and ion velocity co-affect the track damage. The inelastic thermal spike model is used to numerically calculate the spatiotemporal evolutions of energy deposition and the corresponding atomic temperature under different irradiation conditions, and a quantitative relationship is proposed by comparison with corresponding experimentally observed track damage morphologies. Additionally, the obtained quantitative relationship between irradiation conditions and track damage provides deep insight and guidance for understanding the damage behavior of crystal materials in extreme radiation environments and selecting irradiation parameters, including ion species and energies, for ion beam technique application in atomic-level defect manipulation, material modification, and micro/nanofabrication.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The performance evaluation of direct detection electron energy-loss spectroscopy at 200 kV and 80 kV accelerating voltages

Direct electron detectors (DeDs) have been widely used for imaging studies because of their higher beam sensitivity, lower noise, improved pixel resolution, etc. However, there have been limited studies related to the performance in spectroscopic applications for the direct electron detection. Hereby, taking the advantage of the DeD installed on a high-performance electron energy-loss spectrometer, we systematically studied the performance of a DeD (Gatan's K2 IS) fitted on an aberration-corrected transmission electron microscope (TEM) equipped with an electron monochromator. Using SrTiO3 as the model system, the point spread function in the zero-loss region of the spectrum and the performance for core loss spectroscopy have been investigated under both 200 kV and 80 kV operating conditions. We demonstrate that the K2 detector can achieve an overall better performance at 200 kV than a charge coupled device (CCD) detector. At 80 kV, the K2 DeD is still better than a CCD, except for the relative broad tails of the zero-loss peak. The signal-to-noise ratio is very close for DeD and CCD under 80 kV. Based on our data obtained at different operating voltages, it is clear that DeD will benefit the microscopy community and boost the development of cutting-edge materials science studies by pushing the frontiers in electron energy-loss spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2019

Comparison of electron loss models in the inner magnetosphere during the 2013 St. Patrick's Day geomagnetic storm

Electrons with energies in the keV range play an important role in the dynamics of the inner magnetosphere. Therefore, accurately modeling electron fluxes in this region is of great interest. However, these calculations constitute a challenging task since the lifetimes of electrons that are available have limitations. In this study, we simulate electron fluxes in the energy range of 20 eV-100 keV to assess how well different electron loss models can account for the observed electron fluxes during the GEM Challenge Event of the 2013 St. Patrick's Day storm. Three models (Case 1, Case 2, and Case 3) of electron lifetimes due to wave-induced pitch angle scattering are used to compute the fluxes, which are compared with measurements from the Van Allen Probes. The three models consider electron losses due to interactions with whistler mode hiss waves inside the plasmasphere and with whistler mode chorus waves outside the plasmasphere. The Case 1 (historical) model produces excessive loss at low L shells before and after the storm, suggesting that it overestimates losses due to hiss during quiet times. During the storm main phase and early recovery all three models show good agreement with the observations, indicating that losses due to chorus during disturbed times are in general well accounted for by the models. Furthermore, the more recent Case 2 and Case 3 models show overall better agreement with the observed fluxes.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2024

A large net carbon loss attributed to anthropogenic and natural disturbances in the Amazon Arc of Deforestation

The Amazon forest contains globally important carbon stocks, but in recent years, atmospheric measurements suggest that it has been releasing more carbon than it has absorbed because of deforestation and forest degradation. Accurately attributing the sources of carbon loss to forest degradation and natural disturbances remains a challenge because of the difficulty of classifying disturbances and simultaneously estimating carbon changes. We used a unique, randomized, repeated, very high-resolution airborne laser scanning survey to provide a direct, detailed, and high-resolution partitioning of aboveground carbon gains and losses in the Brazilian Arc of Deforestation. Our analysis revealed that disturbances directly attributed to human activity impacted 4.2% of the survey area while windthrows and other disturbances affected 2.7% and 14.7%, respectively. Extrapolating the lidar-based statistics to the study area (544,300 km 2 ), we found that 24.1, 24.2, and 14.5 Tg C y −1 were lost through clearing, fires, and logging, respectively. The losses due to large windthrows (21.5 Tg C y −1 ) and other disturbances (50.3 Tg C y −1 ) were partially counterbalanced by forest growth (44.1 Tg C y −1 ). Our high-resolution estimates demonstrated a greater loss of carbon through forest degradation than through deforestation and a net loss of carbon of 90.5 ± 16.6 Tg C y −1 for the study region attributable to both anthropogenic and natural processes. This study highlights the role of forest degradation in the carbon balance for this critical region in the Earth system.

54 ENVIRONMENTAL SCIENCES↗