Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GAS JET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Flex Dynamics Avoidance Control of the NEA Scout Solar Sail Spacecraft's Reaction Control System

The Attitude Control System (ACS) is developed for a Near Earth Asteroid (NEA) Scout mission using a solar sail. The NEA-Scout spacecraft is a 6U cubesat with an 86 square-meter solar sail. NEA Scout will launch on Space Launch System (SLS) Exploration Mission 1 (EM-1), currently scheduled to launch in 2018. The spacecraft will rendezvous with a target asteroid after a two year journey, and will conduct science imagery. The solar sail spacecraft ACS consists of three major actuating subsystems: a Reaction Wheel (RW) control system, a Reaction Control System (RCS), and an Adjustable Mass Translator (AMT) system. The three subsystems allow for a wide range of spacecraft attitude control capabilities, needed for the different phases of the NEA-Scout mission. Because the sail is a flexible structure, care must be taken in designing a control system to avoid exciting the structural modes of the sail. This is especially true for the RCS, which uses pulse actuated, cold-gas jets to control the spacecraft's attitude. While the reaction wheels can be commanded smoothly, the RCS jets are simple on-off actuators. Long duration firing of the RCS jets - firings greater than one second - can be thought of as step inputs to the spacecraft's torque. On the other hand, short duration firings - pulses on the order of 0.1 seconds - can be thought of as impulses in the spacecraft's torque. These types of inputs will excite the structural modes of the spacecraft, causing the sail to oscillate. Sail oscillations are undesirable for many reasons. Mainly, these oscillations will feed into the spacecraft attitude sensors and pointing accuracy, and long term oscillations may be undesirable over the lifetime of the solar sail. In order to limit the sail oscillations, an RCS control scheme is being developed to minimize sail excitations. Specifically, an input shaping scheme similar to the method described in Reference 1 will be employed. A detailed description of the RCS control scheme will be provided with particular emphasis on flexible body excitation. The RCS performance will be provided to show that sail and boom excitation is minimized.

Heaton Andrew↗
NASA NTRSDate not supplied

Laminar Non-Premixed Flames of Gaseous Fuel Aboard the International Space Station

From late 2017 to early 2022, six independent studies with flames of gaseous fuels were conducted on the International Space Station (ISS) in the U.S. combustion research facility. An exploration of flames at the extremes of high sooting and high dilution was conducted with a coaxial coflow burner, where the fuel and oxidizer velocities were typically matched. An investigation of electric-field effects also used the same coflow burner as well as a simple gas-jet burner, with a circular electrode mesh, downstream of the burner, at voltages of either polarity up to 10 kV. A study focused on material flammability in a quiescent atmosphere emulated the burning of condensed-phased fuels using cylindrical burners with a flat perforated outlet instrumented to measure the heat flux to the burner, i.e., emulated fuel. Three studies of soot processes, flame dynamics, and low-temperature combustion used porous spherical burners, yielding a nominally one-dimensional flame structure. The objectives and selected findings of each investigation will be briefly discussed after a short review of the advantages of studying combustion in microgravity, earlier ISS research, and the experimental hardware and its operation.

flames↗
NASA NTRSDate not supplied

Laminar Non-Premixed Flames of Gaseous Fuel Aboard the International Space Station

From late 2017 to early 2022, six independent studies with flames of gaseous fuels were conducted on the International Space Station (ISS) in the U.S. combustion research facility. An exploration of flames at the extremes of high sooting and high dilution was conducted with a coaxial coflow burner, where the fuel and oxidizer velocities were typically matched. An investigation of electric-field effects also used the same coflow burner as well as a simple gas-jet burner, with a circular electrode mesh, downstream of the burner, at voltages of either polarity up to 10 kV. A study focused on material flammability in a quiescent atmosphere emulated the burning of condensed-phased fuels using cylindrical burners with a flat perforated outlet instrumented to measure the heat flux to the burner, i.e., emulated fuel. Three studies of soot processes, flame dynamics, and low-temperature combustion used porous spherical burners, yielding a nominally one-dimensional flame structure. The objectives and selected findings of each investigation will be briefly discussed after a short review of the advantages of studying combustion in microgravity, earlier ISS research, and the experimental hardware and its operation.

flames↗
NASA NTRSDate not supplied

ACME: Advanced Combustion via Microgravity Experiments

From Nov. 2017 to Feb. 2022, the ACME project’s six independent investigations of laminar, non-premixed flames of gaseous fuels were conducted on the International Space Station (ISS) in the Combustion Integrated Rack (CIR). An exploration of flames at the extremes of high sooting and high dilution was conducted with a coaxial coflow burner, where the fuel and oxidizer velocities were typically matched. An investigation of electric-field effects also used the same coflow burner as well as a simple gas-jet burner, with a circular electrode mesh downstream of the burner, at voltages of either polarity up to 10 kV. A study focused on material flammability in a quiescent atmosphere emulated the burning of condensed-phased fuels using cylindrical burners with a flat perforated outlet instrumented to measure the heat flux to the burner, i.e., emulated fuel. Three studies of soot processes, flame dynamics, and low-temperature combustion used porous spherical burners yielding a nominally one-dimensional flame structure. The ACME research will be represented through images and text.

flames↗
NASA NTRSDate not supplied

The Collection, Usage, and Preliminary Examination of the Apollo Sample Suite: Lessons for Artemis

Apollo Sample Collection and Usage: From 1969 to 1972 there were six Apollo missions to the surface of the Moon during which the astronauts collected 382 kg of rock and regolith (~2200 samples). The samples collected fall into these general categories: rocks (~66% by mass), rake samples (~4%), bulk regolith (~24%), and specialty regolith (deep drill cores, drive tubes, sealed bulk regolith) samples (~6%). In each category there are a variety of different subtypes available for study, e.g., among the bulk regolith samples there are also skim, trench, and (partially) shaded regolith samples each sampling unique types or depths of regolith. This variety of subsamples has enabled a multitude of different studies over the past 55 years (>3400 individual requests). We are still averaging ~50 unique requests and have allocated >500 individual Apollo samples annually for the past 10 years (2020 excepted). Looking at the 4,675 non-ANGSA (Apollo Next Generation Sample Analysis) samples allocated over the past 10 years, the proportions of allocated samples do not precisely align with the abundance (by mass) of those samples withing the collection: Rock (69.4 %); Rake (10.8 %); Bulk Regolith (15.5 %); Drive Tube (3.3 %); Core/Specialty (1.0 %). Apollo Preliminary Examination (PE): The PE process differs significantly for the various sample types enumerated above; we focus on regolith and rock samples here. During the Apollo mission era, the PE process evolved over the course of the missions; below is what was done for the Apollo 17 mission. For regolith samples, the PE process was: (1) documented bags containing regolith are opened, photographed, and described; (2) large rocks are removed and treated separately; (3) 25% to 33% of the bulk soil is scooped out, weighed, and stored in reserve; (4) the remaining sample is sieved to produce the size fractions <1, 1- 2, 2-4, and 4-10 mm, all of which are weighed. For rock samples, the process is: (1) removing rocks from the container(s) it came back from the Moon in; (2) rematching any materials that spalled off the rock to their original location; (3) numbering, weighing, and basic photographic documentation; (4) dusting with a gentle N2 gas jet; (5) Orthogonal photography; (6) detailed description of the textures and features of the rock; (7) rock modelling and measurement; (8) stereophotography; (9) determination of the orientation of the rock on the lunar surface. Drive tubes and deep drill cores were not characterized during PE beyond an initial weight and a sketch of the interior tube materials derived from 2D medical X-ray images. Catalogs: The ongoing utility of the Apollo samples is enabled by the robust cataloguing process for the samples [3-5], which allows the scientific community to accurately request samples uniquely suited to their proposed studies. A common misconception, however, is the amount of detail that goes into the initial catalog (e.g., [6]) for a collection from the preliminary examination (PE) period, versus what goes into the catalogs that come later in the life cycle of the samples from that mission (e.g., [7]). The only required data for a PE catalog is a weight, a basic photograph, and a description of the nature of the sample. Artemis PE: Over the past few years, the ongoing ANGSA project studied previously unopened Apollo 17 double drive tube samples 73001/2 [1], and a PE of the drive tubes was done. The PE took the existing core dissection process (developed during PE of Apollo cores in the 1970s, 1980s), and modernized it [7]. The main lesson from the ANGSA PE relative to future missions was that the physical work done during PE of lunar samples has not changed much over the past 5 decades. The use of “modern” technology during PE (e.g., XCT; multispectral analyses) resulted in an enhanced initial understanding of the 73001 and 73002 drive tubes, but greatly increased the time required. The lessons learned from recent astromaterial PEs (e.g., ANGSA and OREx) are important to consider when planning for Artemis, but the unique nature of the Artemis Campaign means many lessons learned from these mission will not be applicable. Given the time constraints (6 months) and likely number of samples that will be returned by Artemis (>200), the Artemis PE catalog will necessarily look much more like [4] than [6].

J Gross↗
NASA NTRS2012

A Computational Study for the Utilization of Jet Pulsations in Gas Turbine Film Cooling and Flow Control

This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.

Kartuzova, Olga V.↗
NASA NTRS1995

Hot shocked gas along the jets of NGC 4258 (M106)

The ROSAT High Resolution Interferometer (HRI) and Position Sensitive Proportional Counter (PSPC) detectors have been used to study the soft X-ray emission of the nearby SABbc galaxy NGC 4258 (M106). The helically twisted, nuclear jets, previously detected in radio continuum and visual emission-line studies, are found to dominate the X-ray images. After correcting pointing errors of up to +/- 7 sec in our HRI observation, we find that the southeast jet is spatially unresolved transversely along much of its 2.5 min (5 kpc) length. The northwest jet is more diffuse, and the extensive radio 'plateaus' also emit X-rays. The energy spectrum of the jets from the PSPC exposure is noisy but is best fitted as a Raymond-Smith plasma with kT = 0.3 keV, log N(sub H) approximately = 20.0/sq cm, and luminosity 1.6 x 10(exp 40) ergs/s between 0.1 and 2.4 keV. Gas at this temperature can arise from planar shocks of 500 km/s and may have been entrained as the jets scrape along the molecular clous that are known to be adjacent to the jets. The range of radial velocities from our published visual emission-line spectra of the jet are consistent with such a shock speed. We estimate that the mass of hot gas in the jets is 6 x 10(exp 4) (1/cc/n(sub e)) solar mass, with n(sub e) the average electron density. The inferred pressure of hot gas in the southeast jet may be similar to the radio equipartition pressure and to the ambient pressure of the interstellar medium (ISM). The X-ray spectral fit is poor above 0.7 keV and requires an additional hard component that peaks near the nucleus.

Cecil, G.↗
NASA NTRS1992

Small scale jet effects and hot gas ingestion investigations at NASA Ames

The Jet Calibration and Hover Test Facility at NASA Ames has been constructed to perform small scale experiments in hot gas ingestion and jet effects for STOVL aircraft. This new facility and how it is employed to examine the problems associated with STOVL configurations hovering in- and out-of-ground effect are presented. Some of the test procedures and results are described.

Hange, C. E.↗
NASA NTRS2002

Combustion Temperature Measurement by Spontaneous Raman Scattering in a Jet-A Fueled Gas Turbine Combustor Sector

Spontaneous vibrational Raman scattering was used to measure temperature in an aviation combustor sector burning jet fuel. The inlet temperature ranged from 670 K (750 F) to 756 K (900 F) and pressures from 13 to 55 bar. With the exception of a discrepancy that we attribute to soot, good agreement was seen between the Raman-derived temperatures and the theoretical temperatures calculated from the inlet conditions. The technique used to obtain the temperature uses the relationship between the N2 anti-Stokes and Stokes signals, within a given Raman spectrum. The test was performed using a NASA-concept fuel injector and Jet-A fuel over a range of fuel/air ratios. This work represents the first such measurements in a high-pressure, research aero-combustor facility.

Hicks, Yolanda R.↗
DOE OSTI2020

Ionization wave propagation in a He plasma jet in a controlled gas environment

Characterizing ionization wave propagation in low temperature plasma jets is critical to predicting production of reactive species and plasma–surface interactions for biomedical applications and surface functionalization. In this work, results from optical emission and laser induced fluorescence measurements of the ionization wave in a He plasma jet operating in a controlled gas environment are discussed and used for comparison with numerical modeling. Additionally, the ionization wave was observed using ICCD (Intensified Charge Coupled Device) imaging and characterized by time and spatially resolved electron density measurements using laser-collision-induced fluorescence. The plasma jet was initially characterized using pure He (nominally at 200 Torr), while varying pressure and voltage. When operating in pure He, the ionization wave broadly expands exiting the plasma tube. Increasing the operating pressure reduces the speed and isotropic expansion of the ionization wave. Furthermore, the jet operated with a humid He shroud was also studied. The humid He shroud results in the electron density increasing and having an annular profile due to the lower ionization potential of H2O compared to He and localized photoionization in the mixing region. Numerical modeling highlighted the importance of resonance radiation emitted by excited states of He, photoelectron emission from the quartz tube, and the kinetic behavior of the electrons produced by photoionization ahead of the ionization front.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Numerical simulation of an atmospheric pressure plasma jet with coaxial shielding gas

A two-dimensional ( r, z ) numerical simulation of the discharge characteristics of an atmospheric pressure plasma jet (APPJ), with coaxial shielding gas, was performed. The helium working gas flowed in a central capillary tube, engulfing a needle electrode powered by 13.7 MHz radio frequency sinusoidal voltage. The N 2 shielding gas flowed in the annular space of a coaxial tube. These gases emerged, in laminar flow, in a 78%N 2 -21%O 2 -1%Ar dry air ambient. The characteristics of the APPJ with shielding gas were compared to those of the APPJ without shielding gas. The nitrogen shielding gas hindered the diffusion of oxygen and argon from the ambient air into the helium jet. With the shielding gas present, more nitrogen penetrated into the helium core, causing a shorter plasma ‘plume’. The flow rates of the working and shielding gas, critically affected the gas temperature, and in turn the discharge characteristics. For a He flow of 2 standard liters per minute (slm), switching on the nitrogen shielding gas flow (at 4.5 slm) reduced the on-axis O 2 and Ar mole fractions from 3.9 × 10 - 4 to 6.8 × 10 - 5 and from 1.9 × 10 - 5 to 3.3 × 10 - 6 , respectively, at an axial distance of 3 mm downstream of the nozzle. The radial profiles of the mole fractions of the ambient gases were monotonically and strongly decreasing towards the system axis, for short axial distances from the nozzle (~1 mm), but became progressively flatter at longer distances from the nozzle (3 mm and 5 mm). Simulation predictions captured the salient features of experimental data of ambient species mole fractions in the plasma jet, and the 706 nm optical emission intensity profiles of the He 3 3 S excited state.

Physics↗
NASA NTRS1987

Agreement between experimental and theoretical effects of nitrogen gas flowrate on liquid jet atomization

Two-phase flows were investigated by using high velocity nitrogen gas streams to atomize small-diameter liquid jets. Tests were conducted primarily in the acceleration-wave regime for liquid jet atomization, where it was found that the loss of droplets due to vaporization had a marked effect on drop size measurements. In addition, four identically designed two-fluid atomizers were fabricated and tested for similarity of spray profiles. A scattered-light scanner was used to measure a characteristic drop diameter, which was correlated with nitrogen gas flowrate. The exponent of 1.33 for nitrogen gas flowrate is identical to that predicted by atomization theory for liquid jet breakup in the acceleration-wave regime. This is higher than the value of 1.2 which was previously obtained at a sampling distance of 4.4 cm downstream of the atomizer. The difference is attributed to the fact that drop-size measurements obtained at a 2.2 cm sampling distance are less effected by vaporization and dispersion of small droplets and therefore should give better agreement with atomization theory. Profiles of characteristic drop diameters were also obtained by making at least five line-of-sight measurements across the spray at several horizontal positions above and below the center line of the spray.

Ingebo, Robert D.↗
NASA NTRS1987

Agreement between experimental and theoretical effects of nitrogen gas flowrate on liquid jet atomization

Two-phase flows were investigated by using high velocity nitrogen gas streams to atomize small-diameter liquid jets. Tests were conducted primarily in the acceleration-wave regime for liquid jet atomization, where it was found that the loss of droplets due to vaporization had a marked effect on drop-size measurements. In addition, four identically designed two-fluid atomizers were fabricated and tested for similarity of spray profiles. A scattered-light scanner was used to measure a characteristic drop diameter, which was correlated with nitrogen gas flowrate. The exponent of 1.33 for nitrogen gas flowrate is identical to that predicted by atomization theory for liquid jet breakup in the acceleration-wave regime. This is higher than the value of 1.2 which was previously obtained at a smapling distance of 4.4 cm downstream of the atomizer. The difference is attributed to the fact that drop-size measurements obtained at a 2.2 cm sampling distance are less affected by vaporization and dispersion of small droplets and therefore should give better agreement with atomization theory. Profiles of characteristic drop diameters were also obtained by making at least five line-of-sight measurements across the spray at several horizontal positions above and below the center line of the spray.

Ingebo, Robert D.↗