Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Experimental Investigation of Vibratory Stresses in a Concentric-Ring Direct-Air-Cycle Nuclear Fuel Element

Preliminary tests made by the General Electric Company indicated that aerodynamic loads might cause large enough distortions in the thin sheet-metal rings of a nuclear fuel element to result in structural failure. The magnitude of the distortions in a test fuel element was determined from strains measured with airflow conditions simulating those expected during engine operation. The measured vibratory strains were low enough to indicate the improbability of failure by fatigue. A conservative estimate of the radial deflection that accompanied peak strains in the outer ring was +0.0006 inch.

Chiarito, Patrick T.↗
DOE OSTI2021

Post-irradiation examination of legacy high burnup fuel to support safety testing

Safety/transient testing to evaluate performance under off-normal conditions is an essential pillar for both the development of Accident Tolerant Fuels (ATF) and the optimization of fuel operation economics beyond current discharge burnups. Among other factors, the successful interpretation of the transient testing results relies upon the knowledge of the initial conditions of the test, including the characteristics of the fuel system under scrutiny. When testing pre-irradiated material, the assumptions that the fuel and the cladding still have the same properties as in the pre-irradiation stage is obviously wrong and could affect the results of the test. This is particularly true the more burnup accumulates in the fuel rod and irradiation progresses. The knowledge of the initial microstructure of both fuel and cladding allows a clearer interpretation of the subsequent transient testing results, provides validation of the physical phenomena underlying the model predictions and eliminates the uncertainties related to the limited knowledge of the sample status before the test. One example is the phenomenon of fine fragmentation that occurs in Light Water reactor (LWR) fuel. During a Loss of Coolant Accident (LOCA) or Reactivity Initiated Transient (RIA) the fuel can severely fragment. During LOCA, high burnup fuel tend to finely fragment, which has raised safety concerns due to the increased likelihood of dispersal of such small particles once the cladding has burst and due to the increased fission gas release. Therefore, efforts have been devoted to the assessment of a pulverization threshold that could determine the conditions under which fine fragmentation is predominant. However, the lack of information regarding the initial conditions of the fuel, and the connections between those conditions and the pre-transient irradiation history, have hindered the development of a fully mechanistic fragmentation and pulverization criterion. The empirical relationships rely on conservative estimations, due to the lack of information on critical material properties and characteristics. More generally, experimental evidence of the irradiation-induced modifications at microstructural scale are necessary to determine the behavior of the material at the macroscopic scale, with the latter being the one of technological interest. Significant progress has been made in the last two decades in the developments of analytical materials science techniques that can be applied to highly radioactive materials, such as high burnup fuels. The availability of new techniques and the improvement of existing ones has enabled investigations previously not possible that can deepen the understanding of the fuel characteristics and properties at high burnup. The better knowledge of material behavior and irradiation-induced phenomena could help the prediction of its performance. In this context, the scope of the present work is to apply a wide portfolio of advanced characterization techniques to determine properties that are relevant for safety and performance. The results are interpreted in the context of engineering scale post-irradiation examinations and available information on the irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1971

Flow tests of a single fuel element coolant channel for a compact fast reactor for space power

Water flow tests were conducted on a single-fuel-element cooling channel for a nuclear concept to be used for space power. The tests established a method for measuring coolant flow rate which is applicable to water flow testing of a complete mockup of the reference reactor. The inlet plenum-to-outlet plenum pressure drop, which approximates the overall core pressure drop, was measured and correlated with flow rate. This information can be used for reactor coolant flow and heat transfer calculations. An analytical study of the flow characteristics was also conducted.

Springborn, R. H.↗
NASA NTRS1997

Evaluation of an Ejector Ramjet Based Propulsion System for Air-Breathing Hypersonic Flight

A Rocket Based Combined Cycle (RBCC) engine system is designed to combine the high thrust to weight ratio of a rocket along with the high specific impulse of a ramjet in a single, integrated propulsion system. This integrated, combined cycle propulsion system is designed to provide higher vehicle performance than that achievable with a separate rocket and ramjet. The RBCC engine system studied in the current program is the Aerojet strutjet engine concept, which is being developed jointly by a government-industry team as part of the Air Force HyTech program pre-PRDA activity. The strutjet is an ejector-ramjet engine in which small rocket chambers are embedded into the trailing edges of the inlet compression struts. The engine operates as an ejector-ramjet from take-off to slightly above Mach 3. Above Mach 3 the engine operates as a ramjet and transitions to a scramjet at high Mach numbers. For space launch applications the rockets would be re-ignited at a Mach number or altitude beyond which air-breathing propulsion alone becomes impractical. The focus of the present study is to develop and demonstrate a strutjet flowpath using hydrocarbon fuel at up to Mach 7 conditions. Freejet tests of a candidate flowpath for this RBCC engine were conducted at the NASA Lewis Research Center's Hypersonic Tunnel Facility between July and September 1996. This paper describes the engine flowpath and installation, outlines the primary objectives of the program, and describes the overall results of this activity. Through this program 15 full duration tests, including 13 fueled tests were made. The first major achievement was the further demonstration of the HTF capability. The facility operated at conditions up to 1950 K and 7.34 MPa, simulating approximately Mach 6.6 flight. The initial tests were unfueled and focused on verifying both facility and engine starting. During these runs additional aerodynamic appliances were incorporated onto the facility diffuser to enhance starting. Both facility and engine starting were achieved. Further, the static pressure distributions compared well with the results previously obtained in a 40% subscale flowpath study conducted in the LERC 1X1 supersonic wind tunnel (SWT), as well as the results of CFD analysis. Fueled performance results were obtained for the engine at both simulated Mach 6 (1670 K) and Mach 6.6 (1950 K) conditions. For all these tests the primary fuel was liquid JP-10 with gaseous silane (a mixture of 20% SiH4 and 80% H2 by volume) as an ignitor/pilot. These tests verified performance of this engine flowpath in a freejet mode. High combustor pressures were reached and significant changes in axial force were achieved due to combustion. Future test plans include redistributing the fuel to improve mixing, and consequently performance, at higher equivalence ratios.

Thomas, Scott R.↗
DOE OSTI2021

Production, fuel properties and combustion testing of an iso-olefins blendstock for modern vehicles

With the increasing pressure to decarbonize the transportation sector, exploring strategies that can reduce emissions from light-duty vehicles (LDV) has become critical. Bioblendstocks that allow for higher engine efficiency and fuel economy could complement vehicle electrification and help reach carbon neutrality by 2050. In this context, the potential of a mixture of iso-olefins as a bioblendstock was investigated for multimode boosted spark-ignition (SI)/advanced compression ignition (ACI) engine operation designed to achieve higher overall vehicle fuel economy. By establishing the relationship between the molecular structure of iso-olefins and research octane number (RON), octane sensitivity (S) (i.e., the difference between RON and motor octane number [MON]), and phi-sensitivity a dimethyl-hexenes rich olefins mixture (DMHROM) was identified as a preferred blendstock for SI/ACI combustion engines. Here, a pathway for DMHROM production from biomass-derived ethanol was developed and scaled up. More than 1 gallon of DMHROM blendstock was produced for fuel properties assessment including engine testing. Measurements in a Cooperative Fuel Research Engine showed that the DMHROM blendstock possesses a RON of 94 and S of 13.5, and blends synergistically. Rapid compression machine tests coupled with single-cylinder gasoline direct injection engine measurements demonstrated the 20 vol.% DMHROM blend has higher phi-sensitivity than an olefin-free gasoline base fuel and a typical California Reformulated Gasoline Blendstock for Oxygenate Blending (CARBOB) gasoline fuel. These results demonstrate the potential of DMHROM for improving gasoline fuel performance and quality for operation under ACI conditions. The effectiveness of the aftertreatment system in mitigating emissions was verified and showed that the pure DMHROM blendstock and 20 vol.% blend would not increase non-methane organic gases, NO x , and carbon monoxide (CO) emissions. The DMHROM blendstock was found to slightly decrease sooting tendency when added to a gasoline-base fuel (i.e., ~6% reduction at 20 vol.% blending level). Oxidation stability and lubricant compatibility were both confirmed for the 20 vol.% blend. Overall, these results demonstrate that dimethyl-hexenes have potential for improving engine efficiency and fuel economy while meeting emissions regulations and ASTM specifications for gasoline fuel.

09 BIOMASS FUELS↗
NASA NTRS1979

Autoignition of fuels

An autoignition test section and a premixing fuel injector developed to determine the autoignition characteristics of a variety of aircraft fuels are described. Parametric tests to map the ignition delay characteristics of Jet-A fuel were conducted at pressures of 10, 15, 20, 25, and 30 atm, inlet air temperatures up to 900K and fuel-air equivalence ratios of 0.3, 0.5, 0.7, and 1.0. Residence times in the range of 1 to 50 msec were obtained by interchanging spool pieces to create six different mixer/vaporizer lengths (6, 23, 53, 84, 99, and 130 cm) and by testing at two different airflow rates (0.5 and 1.0 kg/sec). The resulting free-stream velocities were in the range 20 to 100 m/sec. As expected, the results indicate that the ignition delay times decrease with increasing air temperature and pressure. Also, the data show that, for lean mixtures, ignition delay times decrease with increasing equivalence ratios.

Spadaccini, L. J.↗
NASA NTRS1987

Combustion characteristics of gas turbine alternative fuels

An experimental investigation was conducted to obtain combustion performance values for specific heavyend, synthetic hydrocarbon fuels. A flame tube combustor modified to duplicate an advanced gas turbine engine combustor was used for the tests. Each fuel was tested at steady-state operating conditions over a range of mass flow rates, fuel-to-air mass ratio, and inlet air temperatures. The combustion pressure, as well as the hardware, were kept nearly constant over the program test phase. Test results were obtained in regards to geometric temperature pattern factors as a function of combustor wall temperatures, the combustion gas temperature, and the combustion emissions, both as affected by the mass flow rate and fuel-to-air ratio. The synthetic fuels were reacted in the combustor such that for most tests their performance was as good, if not better, than the baseline gasoline or diesel fuel tests. The only detrimental effects were that at high inlet air temperature conditions, fuel decomposition occurred in the fuel atomizing nozzle passages resulting in blockage. And the nitrogen oxide emissions were above EPA limits at low flow rate and high operating temperature conditions.

Rollbuhler, R. James↗
NASA NTRS1974

Exploratory tests of two strut fuel injectors for supersonic combustion

Results of supersonic mixing and combustion tests performed with two simple strut injector configurations, one with parallel injectors and one with perpendicular injectors, are presented and analyzed. Good agreement is obtained between static pressure measured on the duct wall downstream of the strut injectors and distributions obtained from one-dimensional calculations. Measured duct heat load agrees with results of the one-dimensional calculations for moderate amounts of reaction, but is underestimated when large separated regions occur near the injection location. For the parallel injection strut, good agreement is obtained between the shape of the injected fuel distribution inferred from gas sample measurements at the duct exit and the distribution calculated with a multiple-jet mixing theory. The overall fraction of injected fuel reacted in the multiple-jet calculation closely matches the amount of fuel reaction necessary to match static pressure with the one-dimensional calculation. Gas sample measurements with the perpendicular injection strut also give results consistent with the amount of fuel reaction in the one-dimensional calculation.

Anderson, G. Y.↗
NASA NTRS1982

Environmental assessment of the 40 kilowatt fuel cell system field test operation

This environmental assessment examines the potential environmental consequences, both adverse and beneficial, of the 40 kW fuel cell system system field test operation. The assessment is of necessity generic in nature since actual test sites were not selected. This assessment provides the basis for determining the need for an environmental impact statement. In addition, this assessment provides siting criteria to avoid or minimize negative environmental impacts and standards for determining candidate test sites, if any, for which site specific assessments may be required.

Bollenbacher, G.↗
NASA NTRS1981

Autoignition characteristics of no. 2 diesel fuel

Parametric tests to map the ignition delay characteristics were conducted at pressures of 3, 4, and 5 atm, inlet air temperatures up to 1150 K and fuel air equivalence ratios ranging from 0.2 to 1.0. Ignition delay times in the range of 6 msec to 60 msec at freestream flow velocities ranging from 10 m/sec to 40 m/sec were obtained. The ignition delay times appeared to correlate with the inverse of pressure and the inverse exponent of temperature.

Tevelde, J. A.↗
DOE OSTI2020

Irradiation performance of nonfertile (Pu-MA-Zr) fast reactor metal fuels

This work was part of a program begun in 2001 to develop advanced nuclear fuels, originally as carriers for plutonium and minor actinides (neptunium, curium, and americium) taken from spent commercial light-water reactors (LWR) so that the plutonium and minor actinides could be ‘burned’ or transmuted in an accelerator or a fast nuclear reactor. A central part of these experiment programs has been the development of advanced fast reactor fuels, because a fast reactor was considered the most efficient vehicle to transmute the actinide waste products, and metallic fuels is a central focus of these tests. An experiment design was developed in which a thermal test reactor, the Advanced Test Reactor (ATR), was used to test small fuel pin prototypes, by creating areas in the core shielded by cadmium filters to produce a largely epithermal and fast neutron spectrum environment in which the pins could be irradiated. The results of non-fertile metallic fuel (no uranium) tests are presented here. Pu-Am-Np-Zr fuels were irradiated to fission densities up to 33 × 10 20 fission/cm 3 and Pu-239 depletions of up to 39%. The depletions were created by roughly 2/3 by fission and 1/3 by transmutation neutron capture. Up to five fuel ‘rodlets’ were irradiated in three sealed capsules stacked axially in the core, and the peak cladding temperatures ranged from 300°C to 500°C, depending on axial location as those near the core centerline are operating hotter and to higher fission densities. Several post-irradiation examinations (precision gamma scanning and fission gas release) were similar to other historical metal fuel experiments in fast reactors. However, optical metallography indicated that two of the rodlets had breached. The exact reasons are unclear. Due to the design of this irradiation experiment a rodlet breach could have increased the temperature in others in the same capsule by contaminating the thermal gap helium with heavier and less conductive fission product gases. Finally, some of those rodlets showed high amounts of fuel/cladding chemical interaction (FCCI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2007

High Fidelity, Fuel-Like Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Test Results

Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer. and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and fueled nuclear testing. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response characteristics and assess potential design improvements at relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design is developed: this is followed by engineering design, fabrication, and testing to validate the overall design process. Test results presented in this paper correspond to a "first cut" simulator design for a potential liquid metal (NaK) cooled reactor design that could be applied for Lunar surface power. Proposed refinements to this simulator design are also presented.

Bragg-Sitton, Shannon M.↗
NASA NTRS1940

Testing of high-octane fuels in the single-cylinder airplane engine

One of the most important properties of aviation fuels for spark-ignition engines is their knock rating. The CFR engine tests of fuels of 87 octane and above does not always correspond entirely to the actual behavior of these fuels in the airplane engine. A method is therefore developed which, in contrast to the octane number determination, permits a testing of the fuel under various temperatures and fuel mixture conditions. The following reference fuels were employed: 1) Primary fuels; isooctane and n-heptane; 2) Secondary fuels; pure benzene and synthetic benzine.

Seeber, Fritz↗
NASA NTRS1989

Hydrocarbon-fueled scramjet combustor component development tests

Technology is being developed for a hydrocarbon-fueled engine operating as a scramjet over the flight Mach number range from 5.6 to 7. A series of connected-pipe tests were performed to define scramjet combustor design criteria applicable to the United Technologies Research Center (UTRC) engine concept which comprises a pair of modular axisymmetric combustor underslung on a supersonic/hypersonic missile. The development of key pilot and fuel injector components of the combustor is pursued in a variable-geometry two-dimensional test section over a range of combustor entrance conditions simulating the intended flight regime. The applicability of the two-dimensional test results to the axisymmetric engine is ensured by maintaining a proper simulation of combustor entrance conditions and preserving the actual length scale in the two-dimensional test configuration. An air-breathing pilot was developed and tested to evaluate flame stabilization and flame propagation characteristics. A pilot configuration was developed that operated stably, with minimal flow spillage, at exhaust stagnation temperatures as high as 4500 R with ethylene fuel. It was demonstrated that the pilot promotes efficient combustion of either gaseous ethylene or preheated liquid Jet-A (JP-5) when they are injected into the supersonic mainstream flow as primary fuels. For the tests with Jet-A fuel, the fuel was heated in an array of internal cooling passages within the pilot walls to a thermodynamic condition such that it would flash-vaporize upon injection into the mainstream flow. The idea of using the air-breathing pilot and distributed primary and secondary fuel injectors to achieve efficient supersonic combustion over a wide range of equivalence ratios was also experimentally demonstrated during the program. During staged fuel injection tests with gaseous ethylene fuel, high secondary fuel combustion efficiencies were achieved and smooth transitions from fully supersonic to dual mode (supersonic/subsonic) operation were demonstrated at high overall equivalence ratios.

Kay, Ira W.↗
DOE OSTI2020

AGR-5/6/7 Operations Update for Technical Coordination Team (Apr 2020)

This is a powerpoint presentation designed to update the Technical Coordination Team (TCT) associated with the AGR irradiation experiment program on operations of the AGR-5/6/7 experiment over the past six months (since the last TCT meeting). The presentation primarily deals with operational challenges to failed fuel particles in capsule 1. Specifically, how to keep fission products from capsule 1 from entering the other four capsules in the experiment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1986

Automotive Stirling engine development program

This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

Ernst, W.↗
NASA NTRS1994

Large Scale Scramjet Propulsion Testing In The Mach 8 and 16 Regime At NASA Ames Research Center

The objective of this paper is to describe the affordable, large scale scramJet test capability for flight Mach numbers between 8 and 16 which has been developed at the NASA Ames Research Center. Details of the Direct Connect Arc Facility DCAF, which can produce combustor test conditions with fuel-on testing for 10 seconds at conditions representative of Mach 8 - 12 flight, are presented and typical test results are described. Likewise, a description of the full scale combustor test capability of the 16 inch shock tunnel is outlined. This facility is characterized by long run times (> 5 milliseconds) for an impulse facility, and it can provide conditions representative of flight conditions from Mach 12 - 16. Typical test results for this shock tunnel are discussed as well. Future upgrades to both facilities are outlined and new uses for their capabilities are discussed.

Arnold, James O.↗