Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fluid management”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Tank 49H Solids Disturbance Analysis

Tank 49H will serve as the feed tank for the Salt Waste Processing Facility (SWPF). Transfers into Tank 49H may disturb solids that have settled to the bottom of the tank, resulting in feed that may exceed the insoluble solids content limit of 1,200 mg/L from the SWPF Waste Acceptance Criteria (WAC). During a transfer into Tank 49H, material that free falls into Tank 49H through a downcomer and passes through the supernate could potentially disturb the solids on the bottom of the tank and scour or suspend solids from a settled solids layer or turbid region. A previous analysis and report evaluated the potential to disturb solids when transferring into Tank 49H through the B4 riser and recommended a minimum tank level of 120 inches to prevent disturbing any solids in the bottom of the tank. The scope of this task is to perform additional fluid flow analysis to determine the impact of a “plunging jet” through the C3 downcomer on solids in Tank 49H and to determine a minimum liquid level to be maintained in Tank 49H prior to transfers that will minimize disturbing the solids and exceeding the SWPF WAC limits for insoluble solids carryover to SWPF since the C3 riser downcomer is at a lower elevation and farther away from the B5 transfer pump than the B4 downcomer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Tank 49H Solids Disturbance Analysis

Tank 49H will serve as the feed tank for the Salt Waste Processing Facility (SWPF). Transfers into Tank 49H may disturb solids that have settled to the bottom of the tank, resulting in feed that may exceed the insoluble solids content limit of 1,200 mg/L from the SWPF Waste Acceptance Criteria (WAC). During a transfer into Tank 49H, material that free falls into Tank 49H through a downcomer and passes through the supernate could potentially disturb the solids on the bottom of the tank and scour or suspend solids from a settled solids layer or turbid region. A previous analysis and report evaluated the potential to disturb solids when transferring into Tank 49H through the B4 riser and recommended a minimum tank level of 120 inches to prevent disturbing any solids in the bottom of the tank. The scope of this task is to perform additional fluid flow analysis to determine the impact of a “plunging jet” through the C3 downcomer on solids in Tank 49H and to determine a minimum liquid level to be maintained in Tank 49H prior to transfers that will minimize disturbing the solids and exceeding the SWPF WAC limits for insoluble solids carryover to SWPF since the C3 riser downcomer is at a lower elevation and farther away from the B5 transfer pump than the B4 downcomer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Crucible Melter Simulation in Nek5000

Nuclear tank waste at the Hanford site is slated for vitrification in large scale refractory-lined melters to transform it into a stable borosilicate waste form suitable for long-term storage or disposal. Molten glass corrodes the refractory lining over time at a rate correlated to the velocity of molten glass against the refractory-lined wall. To properly design a melter and plan for maintenance, it is necessary to accurately model the glass flow and find the correlation between flow velocity and corrosion rate. This modeling was started in STAR-CCM+ CFD software and is being continued in Nek5000 for its fast-running and quick turnaround code. This poster explains the basic process of reconstructing the geometry, fluid properties, and heating of test melters in Nek5000. The geometry is imported from a mesh file and boundary conditions assigned based on surface IDs. The fluid properties are set in the .par and .usr case files. The heating of the actual crucibles in joule heating with electrodes but simulated in Nek5000 with a volumetric heat source term. This volumetric heat source is fit to the actual heating profile with piecewise polynomials and exponentials. Basic results and verification methods are explained in the poster, as well as further work that must be done to complete modeling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Modeling gas breakthrough and flow phenomena through engineered barrier systems using a discrete fracture approach

Compacted clays are being considered to build engineered barrier systems (EBS) intended for the safe isolation of high-level nuclear waste (HLW) and spent nuclear fuel (SNF). The corrosion of the metallic canister containing the HLW/SNF will lead to the generation and buildup of the gas pressure in the more internal part of the clay buffer. This phenomenon would eventually trigger the formation and propagation of fractures in the clay barrier, jeopardizing its safety functions. Here, in this work, we propose to use the fragmentation technique (MFT) to model evolving fractures in clays triggered by gas pressurization. The MFT has been successfully used to model the formation of fractures in concrete, drying cracks in soil, hydraulic and thermo-fractures in rocks. In this work, we extend the MFT to deal with multiphase fluid flow in deformable porous media, and we upgraded a fully coupled computer finite element code using the extended technique. The proposed approach is first verified against analytical solutions and is then applied to model gas breakthrough experiments in clays. A very satisfactory performance of the method is observed in all the analyses, showing the potential of the MFT to tackle multiphase flow problems in deformable porous media with evolving discontinuities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Thermal Optimization of a Silicon Carbide, Half-Bridge Power Module

This project describes the modeling process to design the packaging and heat exchanger for a half-bridge wide-bandgap (WBG) power semiconductor module. The module uses two silicon carbide, metal-oxide-semiconductor field-effect transistor (MOSFET) devices per switch position that are soldered to an aluminum nitride, direct-bond copper (DBC) substrate. A baseplate cooling configuration (e.g., no thermal grease) is used along with a water-ethylene glycol, jet-impingement-style heat exchanger. The heat exchanger was designed to be fabricated using prototyping equipment from the National Renewable Energy Laboratory, complies with automotive standards (for minimal channel sizes, flow rates, and coolant), and considers reliability aspects (i.e., erosion/corrosion). Device-scale computational fluid dynamics (CFD) is used first to design the slot jet impingement cooling configuration and compute the effective heat transfer coefficient (HTC) of the concept. The computed HTCs are then used as boundary conditions for a finite element study to optimize the package geometry (e.g., device layout and baseplate thickness) to minimize thermal resistance and minimize temperature variation between the module's four devices. Finally, a fluid manifold is designed to generate the slot jets and cool the devices. Module-scale CFD predicts a relatively low junction-to-fluid thermal resistance of 16.7 mm2 K/W, a 1.4 degrees C temperature variation between devices, and a total pressure drop of 5,860 Pa (0.85 psi) for the design. The thermal resistance of the module design is about 67% lower than the 2015 BMW i3 power electronics/modules thermal resistance.

DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Effects of flow on uranium speciation in soils impacted by acidic waste fluids

Radioactive acidic liquid waste is a common byproduct of uranium (U) and plutonium (Pu) enrichment and recycling processes whose accidental and planned release has led to a significant input of U into soils and sediments across the world, including at the U.S. DOE's Hanford site (WA, USA). Because of the particularly hazardous nature of U, it is important to predict its speciation when introduced into soils and sediments by acidic waste fluids. Of fundamental importance are the coupled effects of acid-driven mineral transformation and reactive transport on U speciation. To evaluate the effect of waste-fluid residence time and co-associated dissolved phosphate concentrations on U speciation in impacted soils and sediments, uncontaminated surface materials (from the Hanford Site) were reacted with U-containing synthetic acidic waste fluids (pH 2) amended with dissolved phosphate concentrations in both batch (no flow) and flow-through column systems for 7–365 days. By comparing dissolved U behavior and solid phase speciation as a function of flow regimen, we found that the availability of proton-promoted dissolution products (such as Si) to sequester U into uranyl silicates was dependent on waste fluid-sediment contact time as uranyl silicates were not detected in short contact time flow-through systems but were detected in no-flow, long contact time, reactors. Moreover, the dominance of uranyl phosphate as neoprecipitate U scavenger (principally in the form of meta-ankoleite) in phosphate amended systems confirmed the importance of phosphate amendments for an efficient sequestration of U in the soils and sediments. Overall, our experiments suggest that the formation of uranyl silicates in soils impacted by acidic waste fluids is likely to be limited unless reaction products are allowed to accumulate in soil pores, highlighting the importance of investigating soil U speciation in flow-through, transport-driven systems as opposed to no-flow, batch systems. Finally, this study provides insights into uranium speciation and its potential changes under acidic conditions for better prediction of risks and subsequent development of efficient remediation strategies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Performance tuning of CEED software and 1st and 2nd wave apps

The goal of this milestone was the performance tuning of the CEED software, as well as the use and tuning of CEED to accelerate the first and second wave of targeted ECP applications. In this milestone, the CEED team developed optimization techniques and tuned for performance the CEED software to accelerate the first and second wave target ECP applications. Specifically, the focus was on the following: (1) Efficient use of the memory sub-system for managing data motion and interactions among different physics packages and libraries; this included integration of the new developments in a libCEED 0.5 software release; (2) Enhancing the CEED libraries with GPU and AMD GPU support in close interaction with vendors; (3) Optimal data locality and motion, and enhanced scalability and parallelism; this included vendors interactions for improvements in data motion and making strong scaling easier and more efficient; and (4) Continue boosting performance for the first-wave and second-wave of ECP target applications, including ExaSMR, ExaWind, Urban, MARBL, E3SM, and ExaAM. A main part of this milestone was the performance tuning of the CEED first-wave and second-wave ECP applications. This included the ExaSMR application – Coupled Monte Carlo Neutronics and Fluid Flow Simulation of Small Modular Reactors (ORNL), the MARBL application – Next-Gen Multi-physics Simulation Code (LLNL), and the ExaAM ExaConstit – a miniapp for the Transforming Additive Manufacturing through Exascale Simulation applications project (ExaAM), as well as ExaWind, Urban, and E3SM. The artifacts delivered include performance improvements in CEED’s 1st and 2nd wave of applications, and tuned CEED software for various architectures through a number of backends, freely available in the CEED’s repository on GitHub. See the CEED website, http://ceed.exascaleproject.org and the CEED GitHub organization, http://github.com/ceed for more details. In addition to details and results from the above R&D efforts, in this document we are also reporting on other project-wide activities performed in Q4 of FY19 including: CEED’s third annual meeting, MFEM GPU kernels scaling improvements, libCEED 0.5 and NekRS releases, an overview paper covering latest results on a set of bake-off high-order finite element problems (BPs), and other outreach efforts.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Accelerating Multiphase Simulations With Denoising Diffusion Model Driven Initializations

This study introduces a hybrid fluid simulation approach that integrates generative diffusion models with physics‐based simulations, aiming at reducing the computational costs of flow simulations while still honoring all the physical properties of interest. Pore‐scale simulations enhance our understanding of applications such as assessing hydrogen and storage efficiency in underground reservoirs. Nevertheless, they are computationally expensive and the presence of non‐unique solutions can require multiple simulations within a single geometry. To overcome the computational cost hurdle, we propose a method that couples generative diffusion models and physics‐based simulations. While training the data‐driven model, we simultaneously generate initial conditions and perform physics‐based simulations using these. This integrated approach enables us to receive real‐time feedback on a single compute node equipped with both CPUs and GPUs. By efficiently managing these processes within a single compute node, we can continuously monitor performance and halt training once the model meets the specified criteria. To test our model, we generate realizations in a real Berea sandstone fracture which shows that our technique is up to 4.4 times faster than commonly used flow simulation initializations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Design Optimization of A generic Fissile Solution for Mo99 production using Electron Beam-based Neutron Generator using MCNP+CFD

Molybdenum-99 ( 99 Mo) is a medical isotope used in 80% of all medical imaging procedures today. However, 99 Mo is not directly administered to patients for imaging; its decay product, technetium-99m ( 99 mTc), is a metastable isotope with a half-life of ~6 hours. Such a short half-life does not allow for production, separation, and application to a patient before decaying further. Therefore, the solution is to produce the precursor to 99 mTc, 99 Mo. 99 Mo has a half-life of 66 hours, long enough to produce the material and send it to the desired location before it fully decays. Under National Nuclear Security Administration’s (NNSA) highly enriched uranium (HEU) minimization mission, the Material Management and Minimization (M3) office leads the Molybdenum-99 (Mo-99) program. A major goal of the Mo-99 program is to develop methods of producing 99 Mo using low enriched uranium (LEU) opposed to the traditionally used HEU domestically in the U.S. Internationally, LEU is the new standard for use in research reactors and isotope production facility. In this study, we introduce a generic fissile solution system for 99 Mo production facility meeting the design requirement of 1) LEU usage as fissile material and 2) subcritical fissile system coupled with a horizontal electron beam (E-beam) accelerator. The focus of this research is to optimize a fissile solution configuration for maximum 99 Mo production yield using MCNP model, and ultimately implement the optimized design with computational fluid dynamics (CFD) model to understand thermal hydraulic behavior and solution convection characteristic. The report consists of two parts: 1) isotope yield calculation and criticality analysis with a wide range of parametric test matrix, and 2) thermal hydraulic analysis for solution mixing and cooling assessment.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Comparison of Single-Phase Convection in Additive Manufactured Versus Traditional Metal Foams

Abstract Metal foams have been often used for thermal management due to their favorable characteristics including high specific surface area (SSA), high thermal conductivity, and low relative density. However, they are accompanied by shortcomings including the significant contact resistances due to attachment method, as well as the need for characterization of foam parameters such as pore diameter and SSA. Additive manufactured (AM) metal foams would eliminate the substrate/foam thermal resistance, decrease the need for pre-usage characterization, and allow for tailoring structures, while also taking advantage of the characteristics of traditionally manufactured foams. A commercial, aluminum foam (nominally 5 pores per inch (PPI), 86.5% porosity) was analyzed using X-ray microcomputed tomography, and a custom-designed metal foam based on the cell diameter and porosity of the commercial sample was subsequently manufactured. Reduced domain computational fluid dynamics/heat transfer (CFD-HT) models were compared against experimental data. Postvalidation, the flow behavior, effect of varying attachment thermal conductivities, and thermal performance were numerically investigated, demonstrating the usefulness of validated pore-scale models, as well as the potential for improved performance using AM metal foams over traditionally manufactured foams.

Engineering↗
DOE OSTI2024

Integration and Optimization of a Waste Heat Driven Organic Rankine Cycle for Power Generation in Wastewater Treatment Plants

The study focuses on achieving energy self-sufficiency in Wastewater Treatment Plants by proposing a comprehensive model for integrating, sizing, and optimizing an Organic Rankine Cycle system. The Organic Rankine Cycle system is designed to utilize waste heat from the gensets at As Samra Wastewater Treatment Plant in Jordan, where it will contribute to the overall electrical energy supply of the plant. Real data from As Samra Wastewater Treatment Plant is used to model and calculate the available waste heat using TRNSYS® software. The Organic Rankine Cycle model is then developed using ASPEN PLUS® software to explore the impact of operational parameters and determine their optimal values for maximizing the plant's energy profile. An economic analysis is conducted to assess the feasibility of the proposed model, considering system components, installation, operation, and maintenance costs. To optimize the Organic Rankine Cycle system, the study employs the Multi-Output Support Vector Regression technique to capture nonlinear relationships between independent variables (fluid type, turbine inlet pressure, turbine inlet temperature, turbine outlet pressure, and mass flow rate) and dependent variables (pump power input, waste heat input, and turbine specific work). The Osprey optimization algorithm is used to address the multi-objective optimization problem, with the proposed Pareto-based Osprey Optimization Algorithm and the Multi-Objective Particle Swarm Optimization technique being employed to evaluate critical performance and economic parameters such as system thermal efficiency, net power output, and the levelized cost of electricity. The results of the optimization strategies indicate that the M-SVR model's prediction accuracy is significantly improved after parameter optimization, with the model returning high R 2 and low Mean Square Error values of 0.991 and 0.00216, respectively. The Pareto-Based Osprey Optimization Algorithm optimizer identifies the best working fluid as Isobutane/Isopentane in a ratio of 66:34, with optimal turbine inlet pressure and temperature of 15 bars and 218 °C, respectively. In conclusion, the Organic Rankine Cycle model at these optimal conditions achieves a cycle efficiency of 19.93% and an Levelized Cost of Electricity value of 0.0353 USD/kWh.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Geophysical Imaging of Flow and Transport (GIFT): FY24 Status Report

The GIFT (Geophysical Imaging of Flow and Transport) system will improve predictive capabilities as a platform for collecting multi-physical (MP) time-lapse datasets from well-controlled laboratory experiments. This will enable more accurate prediction of multi-phase fluid flow during delivery and transport of insitu remedial amendments as important components of the overall Hanford Site cleanup mission. Design and construction of the GIFT system, which consists of a meter-scale test cell and a network of custom gas circulation and analysis systems, was accomplished in fiscal year (FY) 2024, with plans to add liquid circulation to the system and use this new capability for multi-phase deep vadose experiments starting in FY25.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

SOSAT: Geohazard Risk Assessment in Carbon Sequestration Operations

Like all operations in which fluids are injected into the subsurface, geologic carbon storage (GCS) presents inherit risks that must be assessed and mitigated to successfully deploy such technology in the field. For example, alterations to pore pressure and the stress state due to fluid injection may trigger certain geohazards, such as potential fault activation and induced seismicity or unintentional hydraulic fracturing. Here we present capabilities for assessing these potential risks using the State of Stress Analysis Tool (SOSAT): a Python library and web-based application capable of probabilistically estimating the subsurface state of stress informed by various field observations. Using posterior distributions of principal stress components, SOSAT can assess the risk of fault activation within the injection formation for either a critically oriented fault or a fault with a user-prescribed orientation. Additionally, SOSAT can estimate the probability of unintentional hydraulic fracturing of the intact reservoir rock. Here, we demonstrate these SOSAT capabilities using a hypothetical GCS site. This type of risk assessment can assist with the effective deployment of GCS technology in the field by informing safe design and management practices.

Haagenson, Ryan J.↗
DOE OSTI2023

SiC Microchannel Heat Sinks for High Heat Flux Dissipation of 1 kW/cm 2

Thermal management has become a major barrier in the development of high-power micro-devices. Microchannel heat sinks (MCHS) are a promising method to dissipate high heat fluxes from high power density devices. Reducing the thermal resistance will reduce the temperature increase of the electronic device, allowing for higher powers to be achieved while maintaining a safe operating temperature. This paper reports on the use of silicon carbide (Sic) microchannels to dissipate high heat fluxes up to 1 kW/cm 2 over a footprint of 0.25 cm 2 . The use of high aspect ratio and decreased hydraulic diameter channels has allowed for very low thermal resistances to be achieved at higher heat duties compared to previous studies. The experiments performed resulted in heater temperatures of less than 60 °C and thermal resistances as low as 0.024 cm 2 . ° $C$/W between the heater surface and fluid inlet temperature. In conclusion, the demonstrated thermal performance of the SiC MCHS is an encouraging means for dissipating heat from high power density microelectronic devices.

42 ENGINEERING↗
DOE OSTI2023

Modeling Geologic Waste Repository Systems Below Residual Saturation

The heat generated by high-level radioactive waste can pose numerical and physical challenges to subsurface flow and transport simulators if the liquid water content in a region near the waste package approaches residual saturation due to evaporation. Here, residual saturation is the fraction of the pore space occupied by liquid water when the hydraulic connectivity through a porous medium is lost, preventing the flow of liquid water. While conventional capillary pressure models represent residual saturation using asymptotically large values of capillary pressure, here, residual saturation is effectively modeled as a tortuosity effect alone. Treating the residual fluid as primarily dead-end pores and adsorbed films, relative permeability is independent of capillary pressure below residual saturation. To test this approach, PFLOTRAN is then used to simulate thermal-hydrological conditions resulting from direct disposal of a dual-purpose canister in unsaturated alluvium using both conventional asymptotic and revised, smooth models. Importantly, while the two models have comparable results over 100 000 years, the number of flow steps required is reduced by approximately 94%.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Application of GOTHIC to Groundwater Transport Analysis - 20152

Migration of pollutants and hazardous wastes, potentially containing radioactive isotopes, via groundwater transport is a concern at most waste cleanup sites. Predictive analysis can be used to evaluate mitigating actions intended to minimize impact on the environment and public exposure. GOTHIC is a multipurpose thermal hydraulics code that is used extensively in the nuclear industry for design, licensing and operation evaluations. It combines the capabilities of typical one-dimensional system codes and the essential features of Computational Fluid Dynamics (CFD) codes for three-dimensional analysis. There are other codes that are specifically developed for groundwater transport analysis and the results presented here are consistent with prior analyses. However, GOTHIC has some unique features that offer advantages for applications related to nuclear waste. Most importantly, it has been developed and maintained under a Quality Assurance program in compliance with the requirements of 10CFR50 Appendix B [2] and applicable portions of ASME NQA-1 [3] since 1995. Available GOTHIC capabilities that make the code especially useful for groundwater transport of nuclear materials include: - Tracking of any number of tracer elements for contaminants and other species of interest; - Radioactive decay and progeny of tracer elements; - Adsorption/desorption of tracer elements; - Tracking of any number of dissolved gases; - Release and absorption for dissolved gases; - Vapor phase tracking; - Non-Newtonian fluid modeling. The general porous body modeling approach makes GOTHIC well suited to groundwater transport analysis. The multi-region modeling approach used by GOTHIC simplifies model construction for regions of varying hydrologic characteristics and focuses the computational effort on regions of particular interest while simultaneously capturing the macroscopic response and any feedback effects across the larger domain. The applicability of GOTHIC to groundwater transport applications is demonstrated by comparing code results with available analytic or semi-analytic solutions for groundwater behavior. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Comparison of Full-Field and Integrated CFD Convergence Based on Richardson Extrapolation

This work investigated the usefulness of Richardson extrapolation--based discretization error estimates across all points in a solution field to produce a spatial convergence field for a computational fluid dynamics (CFD) simulation. The presented work used previously developed methods for Richardson extrapolation to compute the convergence orders of a CFD simulation at all points of the base (coarsest) mesh solution. Three test cases of increasing complexity were considered: Poiseuille flow, incompressible flow around a sharp corner, and transonic flow over an RAE 2822 airfoil. These test cases highlighted the potential of the proposed method to identify error sources and their relation to the model system-response-quantity convergence orders. However, these test cases also revealed the immaturity of the proposed method stemming from the unreliability of computing observed convergence orders at single points. Nonetheless, the test cases highlighted that the observed convergence orders allow for a more accurate diagnosis of constructive and destructive error transport than mesh pair error estimates. In the long run, the proposed method can be a tool for developing efficient and advanced error management strategies like adaptive mesh refinement.

Weinmeister, Justin↗
DOE OSTI2024

Site Characterization of the Highest-Priority Geologic Formations for CO2 Storage in Wyoming

The project Site Characterization of the Highest-Priority Geologic Formations for CO2 Storage in Wyoming is one of 9 site characterization projects that were implemented as part of ARRA (American Recovery and Reinvestment Act). Data from this project was used to improve resolution of data in NATCARB in the area of study. Data related to this study has already been incorporated in NATCARB Atlas. The Wyoming Carbon Underground Storage Project (WY-CUSP) consisted of CO2 storage site characterization and evaluation, focusing on Wyoming’s most promising CO2 storage reservoirs (the Pennsylvanian Weber/Tensleep Sandstone and Mississippian Madison Limestone) and premier CO2 storage site (Rock Springs Uplift). Results from the WY-CUSP project suggest the two reservoirs could store up to 17,000 million tons of CO2. The WY-CUSP team drilled a stratigraphic test well and acquired a 3-D seismic survey covering 25 square miles of the Rock Springs Uplift site. The team retrieved 916 feet of core from the 12,810-foot-deep well, along with a complete log suite, borehole images, fluid samples, and other data. Project partners (1) provided continuous visual documentation of the core, including grain size, mineralogy, facies distribution, and porosity; (2) performed continuous permeability and velocity scans of selected reservoir intervals; and (3) chemically analyzed the fluid samples. WY-CUSP scientists integrated seismic attributes with observations from log suites, a VSP survey, core, fluid samples, and laboratory analyses, including continuous permeability scans. From these integrations, researchers constructed 3-D spatial distribution volumes of reservoir and seal properties that represent geological heterogeneity at the targeted CO2 storage site. The WY-CUSP team used this data to perform new CO2 plume migration simulations. Baker Hughes, Inc., completed a series of small-scale, in-situ water injectivity measurements. A database was formed when observations, analyses, and experiments from the stratigraphic test well were integrated. Correlation of these data allowed petrophysical parameters to be extrapolated from the test well out into the storage domain (5x5 mile 3-D seismic survey volume). This resulted in an improved, realistic understanding of performance assessments for potential CO2 storage scenarios. The WY-CUSP team worked on (1) improving CO2 storage resource estimates, (2) establishing long-term integrity and permanence of confining layers, (3) designing a profitable strategy for pressure management, and (4) evaluating the utilization of stored CO2 at the Rock Spring Uplift. Finally, Baker Hughes developed a microseismic baseline for the test site using in-bore geophones to complete field operations.

3-D seismic↗