Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FURNACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Fermilab experience of post-annealing losses in SRF niobium cavities due to furnace contamination and the ways to its mitigation: a pathway to processing simplification and quality factor improvement

We investigate the effect of high temperature treatments followed by only high-pressure water rinse (HPR) of superconducting radio frequency (SRF) niobium cavities. The objective is to provide a cost effective alternative to the typical cavity processing sequence, by eliminating the material removal step post furnace treatment while preserving or improving the RF performance. The studies have been conducted in the temperature range 800-1000C for different conditions of the starting substrate: large grain and fine grain, electro-polished (EP) and centrifugal barrel polished (CBP) to mirror finish. An interesting effect of the grain size on the performances is found. Cavity results and samples characterization show that furnace contaminants cause poor cavity performance, and a practical solution is found to prevent surface contamination. Extraordinary values of residual resistances ~ 1 nOhm and below are then consistently achieved for the contamination-free cavities. These results lead to a more cost-effective processing and improved RF performance, and, in conjunction with CBP, open a potential pathway to acid-free processing.

43 PARTICLE ACCELERATORS↗

Properties of mortars made by uncalcined FGD gypsum-fly ash-ground granulated blast furnace slag composite binder

Highlights: Black-Right-Pointing-Pointer The mortar with uncalcined FGD gypsum has suitable workability. Black-Right-Pointing-Pointer The strength of mortar with uncalcined FGD gypsum is higher than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The dry shrinkage of mortar with uncalcined FGD gypsum is lower than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The leaching of sulfate ion of mortar is studied. - Abstract: A series of novel mortars were developed from composite binder of uncalcined FGD gypsum, fly ash (FA) and ground granulated blast furnace slag (GGBFS) for the good utilization of flue gas desulphurization (FGD) gypsum. At a fixed ratio (20%) of GGBFS to the composite binder, keeping consistency of the mortar between 9.5 and 10.0 cm, the properties of the composite mortar were studied. The results show that higher water/binder (W/B) is required to keep the consistency when increasing the percentage of FGD gypsum. No obvious influences of the W/B and content of FGD gypsum on the bleeding of paste were observed which keeps lower than 2% under all experimental conditions tried. The highest compressive and flexural strengths (ratio is 20% FGD gypsum, 20% GGBFS and 60% FA) are 22.6 and 4.3 MPa at 28 days, respectively. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) results indicate that massive ettringite crystals and C-S-H gels exist in the hydration products. At 90 days the mortars with FGD gypsum is dramatically smaller drying shrinkage (563-938 micro strain) than that without FGD gypsum (about 2250 micro strain). The release of the SO{sub 4}{sup 2-} from the mortar was analyzed, indicating that the dissolution of sulfate increases with FGD gypsum. The concentration of SO{sub 4}{sup 2-} releasing from the mortar with 10% FGD gypsum is almost equal to that obtained from the mortar without FGD gypsum. The release of SO{sub 4}{sup 2-} from the mortar with 20% FGD gypsum is 9200 mg{center_dot}m{sup -2}, which is lower than that from the mortar with 95% cement clinker and 5% FGD gypsum.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Phase Development of NaOH Activated Blast Furnace Slag Geopolymers Cured at 90 deg. C

Geopolymers were synthesized from blast furnace slag activated with different levels of NaOH and cured at 90 deg. C. The crystalline and amorphous phases of the resulting geopolymers were characterized by XRD quantitative analysis, and {sup 29}Si and {sup 27}Al MAS NMR. Amorphous species are predominant in materials at all NaOH levels. In the amorphous phase, aluminium substituted silicate species (Q{sup 2}(1Al)) dominated among the species of Q{sup 0}, Q{sup 1}, Q{sup 2}(1Al) and Q{sup 2}(where Q{sup n}(mAl) denotes a silicate tetrahedron [SiO{sub 4}] with n bridging oxygen atoms and m adjacent tetrahedra substituted with an aluminate tetrahedron [AlO{sub 4}]). In addition, it was also found that 4-fold coordination aluminium [AlO{sub 4}] species ({sup 27}Al chemical shift 66.1 ppm) in low NaOH containing materials differs from the species ({sup 27}Al chemical shift 74.3 ppm) in high NaOH containing materials.

36 MATERIALS SCIENCE↗

Building America Top Innovations 2013 Profile – High-Performance Furnace Blowers

This Top Innovations profile describes Lawrence Berkeley National Laboratory's work with furnace blower design that led to the creation of a standard for rating blowers, credits for the use of good blowers in Federal tax credit programs and energy codes, and consideration in current federal rulemaking procedures.

air conditioner↗

Reduction of iron-oxide-carbon composites: part II. Rates of reduction of composite pellets in a rotary hearth furnace simulator

A new ironmaking concept is being proposed that involves the combination of a rotary hearth furnace (RHF) with an iron-bath smelter. The RHF makes use of iron-oxide-carbon composite pellets as the charge material and the final product is direct-reduced iron (DRI) in the solid or molten state. This part of the research includes the development of a reactor that simulated the heat transfer in an RHF. The external heat-transport and high heating rates were simulated by means of infrared (IR) emitting lamps. The reaction rates were measured by analyzing the off-gas and computing both the amount of CO and CO{sub 2} generated and the degree of reduction. The reduction times were found to be comparable to the residence times observed in industrial RHFs. Both artificial ferric oxide (PAH) and naturally occurring hematite and taconite ores were used as the sources of iron oxide. Coal char and devolatilized wood charcoal were the reductants. Wood charcoal appeared to be a faster reductant than coal char. However, in the PAH-containing pellets, the reverse was found to be true because of heat-transfer limitations. For the same type of reductant, hematite-containing pellets were observed to reduce faster than taconite-containing pellets because of the development of internal porosity due to cracking and fissure formation during the Fe2O{sub 3}-to-Fe3O{sub 4} transition. This is, however, absent during the reduction of taconite, which is primarily Fe3O{sub 4}. The PAH-wood-charcoal pellets were found to undergo a significant amount of swelling at low-temperature conditions, which impeded the external heat transport to the lower layers. If the average degree of reduction targeted in an RHF is reduced from 95 to approximately 70 pct by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced 1.5 to 2 times. The use of a two- or three-layer bed was found to be superior to that of a single layer, for higher productivities.

01 COAL, LIGNITE, AND PEAT↗

Modeling of Radiative Heat Transfer in an Electric Arc Furnace

Radiation is an important means of heat transfer inside an electric arc furnace (EAF). To gain insight into the complex processes of heat transfer inside the EAF vessel, not only radiation from the surfaces but also emission and absorption of the gas phase and the dust cloud need to be considered. Furthermore, the radiative heat exchange depends on the geometrical configuration which is continuously changing throughout the process. The present paper introduces a system model of the EAF which takes into account the radiative heat transfer between the surfaces and the participating medium. This is attained by the development of a simplified geometrical model, the use of a weighted-sum-of-gray-gases model, and a simplified consideration of dust radiation. The simulation results were compared with the data of real EAF plants available in literature.

42 ENGINEERING↗

Modeling and Simulation of the Off-gas in an Electric Arc Furnace

The following paper describes an approach to process modeling and simulation of the gas phase in an electric arc furnace (EAF). The work presented represents the continuation of research by Logar, Dovžan, and Škrjanc on modeling the heat and mass transfer and the thermochemistry in an EAF. Due to the lack of off-gas measurements, Logar et al. modeled a simplified gas phase under consideration of five gas components and simplified chemical reactions. The off-gas is one of the main continuously measurable EAF process values and the off-gas flow represents a heat loss up to 30 pct of the entire EAF energy input. Therefore, gas phase modeling offers further development opportunities for future EAF optimization. This paper presents the enhancement of the previous EAF gas phase modeling by the consideration of additional gas components and a more detailed heat and mass transfer modeling. In order to avoid the increase of simulation time due to more complex modeling, the EAF model has been newly implemented to use an efficient numerical solver for ordinary differential equations. Compared to the original model, the chemical components H{sub 2}, H{sub 2}O, and CH{sub 4} are included in the gas phase and equilibrium reactions are implemented. The results show high levels of similarity between the measured operational data from an industrial scale EAF and the theoretical data from the simulation within a reasonable simulation time. In the future, the dynamic EAF model will be applicable for on- and offline optimizations, e.g., to analyze alternative input materials and mode of operations.

42 ENGINEERING↗

Thermal Analysis on the Pyrolysis of Tetrabromobisphenol A and Electric Arc Furnace Dust Mixtures

The pyrolysis of Tetrabromobisphenol A (TBBPA) mixed with electric arc furnace dust (EAFD) was studied using thermogravimetric analysis (TGA) and theoretically analyzed using thermodynamic equilibrium calculations. Mixtures of both materials with varying TBBPA loads (1:1 and 1:3) were prepared and pyrolyzed in a nitrogen atmosphere under dynamic heating conditions at heating rates of 5 and 10 °C/min. The mixtures degraded through several steps, including decomposition of TBBPA yielding mainly HBr, bromination of metal oxides, followed by their evaporation in the sequence of CuBr{sub 3}, ZnBr{sub 2}, PbBr{sub 2}, FeBr{sub 2}, MnBr{sub 2}, KBr, NaBr, CaBr{sub 2}, and MgBr{sub 2}, and finally reduction of the remaining metal oxides by the char formed from decomposition of TBBPA. Thermodynamic calculations suggest the possibility of selective bromination of zinc and lead followed by their evaporation, leaving iron in its oxide form, while the char formed may serve as a reduction agent for iron oxides into metallic iron. However, at higher TBBPA volumes, iron bromide forms, which can also be evaporated at a temperature higher than those of ZnBr{sub 2} and PbBr{sub 2}. Results from this work provide practical insight into selective recovery of valuable metals from EAFD while at the same time recycling the hazardous bromine content in TBBPA.

36 MATERIALS SCIENCE↗

Study on the Fluid Flow Characteristics of Coherent Jets with CO{sub 2} and O{sub 2} Mixed Injection in Electric Arc Furnace Steelmaking Processes

As an efficient oxygen supplying technology, coherent jets are widely applied in electric arc furnace (EAF) steelmaking processes to strengthen chemical energy input, speed up smelting rhythm, and promote the uniformity of molten bath temperature and compositions. Recently, the coherent jet with CO{sub 2} and O{sub 2} mixed injection (COMI) was proposed and demonstrated great application potentiality in reducing the dust production in EAF steelmaking. In the present study, based on the eddy dissipation concept model, a computational fluid dynamics model of coherent jets with COMI was built with the overall and detailed chemical kinetic mechanisms (GRI-Mech 3.0). Compared with one-step combustion reaction, GRI-Mech 3.0 consists of 325 elementary reactions with 53 components and can predict more accurate results. The numerical simulation results were validated by the combustion experiment data. The jet behavior and the fluid flow characteristics of coherent jets with COMI under 298 K and 1700 K (25 °C and 1427 °C) were studied and the results showed that for coherent jets with COMI, the chemical effect of CO{sub 2} significantly weakened the shrouding combustion reactions of CH{sub 4} and the relative importance of the chemical effect of CO{sub 2} increases with CO{sub 2} concentration increasing. The potential core length of coherent jet decreases with the volume fraction of CO{sub 2} increasing. Moreover, it also can be found that the potential core length of coherent jets was prolonged with higher ambient temperature.

36 MATERIALS SCIENCE↗

Effect of Hydrogen Addition on Softening and Melting Reduction Behaviors of Ferrous Burden in Gas-Injection Blast Furnace

The softening and melting reduction behaviors of ferrous burden in a gas-injection blast furnace (BF) have been investigated experimentally with the assistance of H{sub 2}. The results indicate that the initial softening temperature of the burden in the BF is lower than that in the traditional BF, while the opposite trend is observed for its melting and dripping temperatures, thus widening the softening range and narrowing the melting zone. As a result, the permeability of the stock column is apparently improved, owing to the decreased amount of the produced melt. After H{sub 2} gas is added, the thickness of the iron shell of the burden pellet increases, and the quantity of its liquid wüstite core decreases due to the higher reduction degree. The reduction rate of iron oxides is much faster than the carburization rate with the H{sub 2} addition, and the dripping behavior of the ferrous burden is determined by the carburization with a high reduction potential. After taking into account the effects of H{sub 2} addition on the iron oxide reduction rate, melt quantity, burden microstructure, and energy consumed by the gas-injection BF, it has been concluded that the optimal H{sub 2} content lies in the range between 10 and 15 pct.

36 MATERIALS SCIENCE↗

Transient Interaction Between Reduction and Slagging Reactions of Wustite in Simulated Cohesive Zone of Blast Furnace

The blast furnace cohesive zone plays an important role in the gas flow distribution and heat-transfer efficiency. Previous work mainly employed temperature-based indices to evaluate and predict the shape and thickness of the cohesive zone, whereas the internal reactions and related effects on the softening and melting properties of a complex burden are ignored. In this study, an innovative index, namely, shrinkage rate (SR), is first proposed to directly estimate the shrinkage behavior of wustite (FeO)-packed bed inside a simulated cohesive zone. The index is applied as the temperature increases to elucidate the transient interaction between reduction and slagging reactions. Results show that the thermally induced slagging reaction causes the packed bed to shrink at lower temperature, and the SR doubles when compounds with low melting temperature are generated by adding a reasonable concentration of CaO or SiO{sub 2}. The reduction reaction becomes the driving force during the shrinkage of the packed bed between 1173 K and 1273 K when CO is introduced in the mixture gas. Then, the dominating factors for further shrinkage include slagging, reduction, or both factors. These factors vary with respect to the added compounds or temperature.

36 MATERIALS SCIENCE↗

Effect of Direct Reduced Iron (DRI) on Dephosphorization of Molten Steel by Electric Arc Furnace Slag

We investigated the effect of direct reduced iron (DRI) addition on dephosphorization of molten steel by electric arc furnace (EAF) slag at 1823 K (1550 °C). Various phenomena such as CO gas evolution and slagmaking by gangue oxides in DRI were experimentally observed at each reaction step. Thermodynamic behaviors of phosphorus, oxygen, and carbon were strongly dependent on DRI content. Basicity, which is the thermodynamic driving force of dephosphorization, decreased with the increasing DRI content because SiO{sub 2} concentration in the slag was proportional to DRI addition. The excess free energy of P{sub 2}O{sub 5} increased with the increasing SiO{sub 2} content in slag. A higher DRI content made dephosphorization difficult by decreasing the basicity and stability of P{sub 2}O{sub 5} in the slag. Therefore, when using DRI in EAF process, it is very important to control the basicity of slag.

36 MATERIALS SCIENCE↗

Optimization of Mineralogy and Microstructure of Solidified Basic Oxygen Furnace Slag Through SiO{sub 2} Addition or Atmosphere Control During Hot-Stage Slag Treatment

Valorization of basic oxygen furnace (BOF) slag is of significant importance for mitigation of the steel production’s environmental impact. The present work aims to investigate the influence of SiO{sub 2} addition and oxygen partial pressure on the mineralogical modification of a typical industrial BOF slag. The slag basicity (mass ratio of CaO/SiO{sub 2}) was varied from 1.8 to 4.4 by mixing specific amounts of SiO{sub 2} with the master BOF slag. The original and modified slags were remelted and solidified under argon or air atmosphere followed by slow cooling. The experimental observations were then compared with the results of thermodynamic modeling to achieve a thorough understanding. With decreasing the basicity, free lime was eliminated, as it forms dicalcium silicate (Ca{sub 2}SiO{sub 4}). With increasing oxygen partial pressure, wustite was oxidized to hematite, which combined with free lime to form calcium aluminoferrite (C{sub 2}AF). The effects of SiO{sub 2} addition and oxygen partial pressure were finally evaluated with respect to the energy consumption for the BOF slag valorization. The modified slag is suitable as a precursor for construction applications as binders.

36 MATERIALS SCIENCE↗

Influence of Aluminum-Carbon Composite Pellets on FeO Reduction and Iron Recovery from Electric Arc Furnace Slag

We investigated the effect of Al-C composite pellets (ACCP) on the reduction behavior of FeO in electric arc furnace (EAF) slag and the iron recovery at different n{sub Al}/(n{sub Al} + n{sub C}) at 1823 K (1550 °C). A carbothermic reaction was the dominant process at n{sub Al}/(n{sub Al} + n{sub C}) < 0.4, whereas aluminothermic reduction was the major process at n{sub Al}/(n{sub Al} + n{sub C}) > 0.6; these observations are based on the final content of FeO and Al{sub 2}O{sub 3} in the molten slag. The aluminum and carbon present in the ACCP competitively affected the reaction stoichiometry (i.e., the material balance) between the production of CO + Al{sub 2}O{sub 3} and the consumption of FeO. Iron recovery increased up to a yield of approx. 90 pct as the n{sub Al}/(n{sub Al} + n{sub C}) ratio increased. Because Al in the ACCP readily reacts to reduce FeO in the molten slag, iron recovery is proportional to the n{sub Al}/(n{sub Al} + n{sub C}) ratio. The precipitation of solid compounds in the slag phase, such as monoxide ([Mg,Fe]·O) and spinel (MgO·Al{sub 2}O{sub 3}), occurred during FeO reduction; this was experimentally confirmed as well as by thermochemical computation. Furthermore, we proposed a schematic reaction mechanism in the present study.

36 MATERIALS SCIENCE↗

Experimental and Mathematical Simulation Study on the Granulation of a Modified Basic Oxygen Furnace Steel Slag

Basic oxygen furnace (BOF) steel slag is a major waste of the steelmaking industry. Utilization of BOF slag contributes to the sustainability of the steel industry by alleviating its environmental impact. Vitrification during cooling is an effective method to promote the cementitious activity of slags with the aim to apply slags in high value-added applications. In the present study, an Al{sub 2}O{sub 3}- and SiO{sub 2}-modified BOF slag was water granulated at a pilot scale. The amorphous and mineral fractions were measured quantitatively. The critical cooling rate to vitrify the modified slag was calculated through the Time-Temperature-Transformation diagrams constructed using in situ confocal scanning laser microscopy. To provide an insight into the crystallization behavior during the granulation process, a mathematical model was developed. The model was validated by comparing the amorphous fraction obtained from experiments with that from simulation. Temperature profiles of the slag particles with varied sizes were calculated with the aid of COMSOL Multiphysics software. The effect of particle size on the vitrified fraction was discussed in detail and the temperature gradient from surface to center of the particle was identified. The results provide novel fundamental understanding of the vitrification process regarding to the slag valorization, which will help the industrial implementation of granulation for pollution remediation and other engineered environmental systems such as chemical industry and pharmaceutical industry.

36 MATERIALS SCIENCE↗

Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking

The state of the interface between slag and carbon determines the slag foaming behavior and thus the effectiveness of carbon in electric arc furnace (EAF) steelmaking. This paper explores the interaction between synthetic slag and carbonaceous materials derived from various sources, including bio-char produced by two different technologies, graphite, coke, and char from tire pyrolysis. Different interfacial phenomena were found between slag and the carbonaceous materials examined. The interactions between bio-char and slag are found to be poor in comparison with other carbonaceous materials. Carbonaceous materials were characterized in terms of their chemical composition and the results obtained suggested that interfacial phenomena were not dominated by ash in the carbonaceous material. The effects of carbon crystalline structure on interaction with slag were evaluated by Raman spectroscopy and X-ray diffraction. Surface properties of the samples were evaluated using scanning electron microscopy, and surface morphology was identified as the principal factor affecting the interaction of slag on carbonaceous particles. The smooth surface of bio-char results in reduced slag foaming. This finding forms the basis for future research on the production of bio-char to be used as a slag foaming agent in EAF steelmaking.

36 MATERIALS SCIENCE↗

High-Temperature Interactions Between Vanadium-Titanium Magnetite Carbon Composite Hot Briquettes and Pellets Under Simulated Blast Furnace Conditions

The high-temperature interactions between vanadium-titanium magnetite carbon composite hot briquettes (VTM-CCBs) and pellets were systematically investigated under simulated blast furnace conditions with respect to the reduction behavior, softening–melting–dripping characteristics, gas permeability, and Ti(C, N) precipitation mechanisms. The results showed that VTM-CCB charging can promote the reduction of the pellet in the packed bed and decrease the compressive strength of the pellet after reduction. The compressive strength of the VTM-CCB after reduction decreased with increasing temperature when the FC/O ratio (the ratio of the fixed carbon mol(C) in coal to the reducible oxygen mol(O) in iron oxides) was higher than 1.0. With an FC/O ratio lower than 1.0, the compressive strength of the VTM-CCB initially decreased and then increased. The FC/O ratio has a significant influence on the softening–melting interaction mechanism between the VTM-CCB and the pellet. With an FC/O ratio of 0.8, the bonding layer at the interface between the pellet and the VTM-CCB (consisting of molten fayalitic slag) can promote the softening process, thereby decreasing the softening start and end temperatures. By increasing the FC/O ratio to 1.4, a dense metallic iron shell with relatively high strength formed at the interface and restricted the collapse of the packed bed, thereby increasing the softening start and end temperatures and ensuring the transport of the reduction gas through the packed bed. The melting point of the primary slag phase increased with increasing FC/O ratio due to a decrease in the FeO content, which resulted in an increase in the melting start temperature from 1273 °C to 1294 °C (1546 K to 1567 K). The gas permeability in the cohesive zone increased with an increasing FC/O ratio of the VTM-CCB due to a combination of the skeletal role performed by the residual VTM-CCB and the decrease in the liquid slag proportion. In addition, as the FC/O ratio increased to 1.4, unconsumed carbon promoted the precipitation of Ti(C, N) at the slag–carbon and slag–metal interfaces, which resulted in a substantial increase in the dripping temperature and deterioration of the dripping behavior of the packed bed. Therefore, to suppress the precipitation of Ti(C, N) and improve the dripping behavior of the packed bed, the FC/O ratio of the charged VTM-CCB should be controlled within an appropriate range.

36 MATERIALS SCIENCE↗