Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering - Particle accelerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1969

The simulator to match the transports to come.

Flight simulator with large lateral motion for large and supersonic transport aircraft, emphasizing reproduction of cockpit accelerations due to supersonic engine thrust loss

Dusterberry, J. C.↗
NASA NTRS1973

Shuttle cryogenic supply system optimization study. Volume 5A-2: Users manual for Space shuttle orbit injection system analysis (SOPSA)

SOPSA (Shuttle Orbit Injection Propulsion System Analysis) is a computer program to aid in the preliminary design of propellant feed systems for the space shuttle orbiter main engines. The primary purpose of the program is to evaluate propellant tank ullage pressure requirements imposed by the need to accelerate propellants rapidly during the engine start sequence. These requirements can influence the system design for a given engine as well as the suitability of a given system for use with different engines. During the vehicle design phase, the SOPSA program is used to establish feed system weight variations as a function of nominal line diameter and component and line configurations. The weight data are used in conjunction with pertinent cost data to establish optimum feed system designs.

Source record↗
NASA NTRS1975

Summary and analysis of performance and stability characteristics of the refan JT8D-109 engine

The refan JT8D-109 performance and stability characteristics are reported as determined from sea level testing, altitude testing, and DC-9 flight testing. The test results are summarized as follows: (1) TSFC at SLS achieved design goal of 12.66 percent reduction. (2) TSFC at altitude average cruise power 0.5 percent higher than design goal, (3) TSFC at altitude maximum cruise power 1.7-3.7 percent higher than design goal, (4) ground starting consistent with JT8D-9 base engine, (5) successful flight starts without starter assist, (6) transient surge margin equivalent to JT8D-9, (7) stable engine operation with inlet distortion, and (8) stable engine operation during snap acceleration and deceleration. A flight idle setting is required for acceptable aborted-landing go-around acceleration time due to increase in low-rotor moment of inertia, and a performance improvement program should be conducted as part of any future certification program.

Sanberg, K. G.↗
NASA NTRS1977

Solution of transient optimization problems by using an algorithm based on nonlinear programming

An algorithm is presented for solution of dynamic optimization problems which are nonlinear in the state variables and linear in the control variables. It is shown that the optimal control is bang-bang. A nominal bang-bang solution is found which satisfies the system equations and constraints, and influence functions are generated which check the optimality of the solution. Nonlinear optimization (gradient search) techniques are used to find the optimal solution. The algorithm is used to find a minimum time acceleration for a turbofan engine.

Teren, F.↗
NASA NTRS1977

Solution of transient optimization problems by using an algorithm based on nonlinear programming

A new algorithm is presented for solution of dynamic optimization problems which are nonlinear in the state variables and linear in the control variables. It is shown that the optimal control is bang-bang. A nominal bang-bang solution is found which satisfies the system equations and constraints, and influence functions are generated which check the optimality of the solution. Nonlinear optimization (gradient search) techniques are used to find the optimal solution. The algorithm is used to find a minimum time acceleration for a turbofan engine.

Teren, F.↗
NASA NTRS1980

Advanced propulsion system for hybrid vehicles

A number of hybrid propulsion systems were evaluated for application in several different vehicle sizes. A conceptual design was prepared for the most promising configuration. Various system configurations were parametrically evaluated and compared, design tradeoffs performed, and a conceptual design produced. Fifteen vehicle/propulsion systems concepts were parametrically evaluated to select two systems and one vehicle for detailed design tradeoff studies. A single hybrid propulsion system concept and vehicle (five passenger family sedan)were selected for optimization based on the results of the tradeoff studies. The final propulsion system consists of a 65 kW spark-ignition heat engine, a mechanical continuously variable traction transmission, a 20 kW permanent magnet axial-gap traction motor, a variable frequency inverter, a 386 kg lead-acid improved state-of-the-art battery, and a transaxle. The system was configured with a parallel power path between the heat engine and battery. It has two automatic operational modes: electric mode and heat engine mode. Power is always shared between the heat engine and battery during acceleration periods. In both modes, regenerative braking energy is absorbed by the battery.

Norrup, L. V.↗
NASA NTRS1984

Transient flow combustion

Non-steady combustion problems can result from engine sources such as accelerations, decelerations, nozzle adjustments, augmentor ignition, and air perturbations into and out of the compressor. Also non-steady combustion can be generated internally from combustion instability or self-induced oscillations. A premixed-prevaporized combustor would be particularly sensitive to flow transients because of its susceptability to flashback-autoignition and blowout. An experimental program, the Transient Flow Combustion Study is in progress to study the effects of air and fuel flow transients on a premixed-prevaporized combustor. Preliminary tests performed at an inlet air temperature of 600 K, a reference velocity of 30 m/s, and a pressure of 700 kPa. The airflow was reduced to 1/3 of its original value in a 40 ms ramp before flashback occurred. Ramping the airflow up has shown that blowout is more sensitive than flashback to flow transients. Blowout occurred with a 25 percent increase in airflow (at a constant fuel-air ratio) in a 20 ms ramp. Combustion resonance was found at some conditions and may be important in determining the effects of flow transients.

Tacina, R. R.↗
NASA NTRS1986

Life cycle cost assessment of future low heat rejection engines

The Adiabatic Diesel Engine Component Development (ADECD) represents a project which has the objective to accelerate the development of highway truck engines with advanced technology aimed at reduced fuel consumption. The project comprises three steps, including the synthesis of a number of engine candidate designs, the coupling of each with a number of systems for utilizing exhaust gas energy, and the evaluation of each combination in terms of desirability. Particular attention is given to the employed evaluation method and the development of this method. The objective of Life Cycle Cost (LCC) evaluation in the ADECD program was to select the best from among 42 different low heat rejection engine (LHRE)/exhaust energy recovery system configurations. The LCC model is discussed along with a maintenance cost model, the evaluation strategy, the selection of parameter ranges, and a full factorial analysis.

Petersen, D. R.↗
NASA NTRS1999

Design of a Novel Gaseous Hydrogen-Oxygen Rocket Injector Element

NASA and Aerojet are developing a Rocket-Based Combined Cycle (RBCC) engine under the Advanced Reusable Technology program. The rocket application requires that the combustion process be stable, complete, and take place in as short a distance as possible without compromising the structural integrity of the injector itself. A novel gaseous hydrogen-oxygen rocket injector element design was arrived at through an iterative design process making extensive use of CFD simulations, which resulted in a design that is meeting design goals. Sub-scale versions of the injector have been built and tested in a unique test-rig and in a sub-scale RBCC engine. The Aerojet RBCC concept integrates small rocket thrusters into the rearfacing base area of struts placed in the flowpath of a scramjet (Supersonic Combusting Ramjet) engine. In one mode of operation, at vehicle takeoff, the rockets provide the primary thrust with additional thrust coming from an ejector effect as air is drawn into the engine inlet, entrained, and accelerated by the rocket exhaust.

Glenn, Dennis E.↗
NASA NTRS1999

High-Energy Space Propulsion Based on Magnetized Target Fusion

Magnetized target fusion is an approach in which a magnetized target plasma is compressed inertially by an imploding material wall. A high energy plasma liner may be used to produce the required implosion. The plasma liner is formed by the merging of a number of high momentum plasma jets converging towards the center of a sphere where two compact toroids have been introduced. Preliminary 3-D hydrodynamics modeling results using the SPHINX code of Los Alamos National Laboratory have been very encouraging and confirm earlier theoretical expectations. The concept appears ready for experimental exploration and plans for doing so are being pursued. In this talk, we explore conceptually how this innovative fusion approach could be packaged for space propulsion for interplanetary travel. We discuss the generally generic components of a baseline propulsion concept including the fusion engine, high velocity plasma accelerators, generators of compact toroids using conical theta pinches, magnetic nozzle, neutron absorption blanket, tritium reprocessing system, shock absorber, magnetohydrodynamic generator, capacitor pulsed power system, thermal management system, and micrometeorite shields.

Thio, Y. C. F.↗