Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Comparison of temperature data from a four-vane static cascade and a research gas turbine engine for a chordwise-finned, impingement- and film-cooled vane

Experimental heat-transfer data obtained for a chordwise-finned, impingement- and film-cooled turbine vane tested in a four-vane static cascade to a gas temperature and a gas pressure of 2250 F and 80 psia, respectively, are presented. Average and local vane temperatures are correlated and compared with correlations of temperature data obtained from tests of the same vane in a modified J-75 turbojet engine. The measured vane temperatures obtained from these tests in the two test stands are also compared with analytically determined temperatures.

Gladden, H. J.↗
NASA NTRS1993

Aerodynamic heating in hypersonic flows

Aerodynamic heating in hypersonic space vehicles is an important factor to be considered in their design. Therefore the designers of such vehicles need reliable heat transfer data in this respect for a successful design. Such data is usually produced by testing the models of hypersonic surfaces in wind tunnels. Most of the hypersonic test facilities at present are conventional blow-down tunnels whose run times are of the order of several seconds. The surface temperatures on such models are obtained using standard techniques such as thin-film resistance gages, thin-skin transient calorimeter gages and coaxial thermocouple or video acquisition systems such as phosphor thermography and infrared thermography. The data are usually reduced assuming that the model behaves like a semi-infinite solid (SIS) with constant properties and that heat transfer is by one-dimensional conduction only. This simplifying assumption may be valid in cases where models are thick, run-times short, and thermal diffusivities small. In many instances, however, when these conditions are not met, the assumption may lead to significant errors in the heat transfer results. The purpose of the present paper is to investigate this aspect. Specifically, the objectives are as follows: (1) to determine the limiting conditions under which a model can be considered a semi-infinite body; (2) to estimate the extent of errors involved in the reduction of the data if the models violate the assumption; and (3) to come up with correlation factors which when multiplied by the results obtained under the SIS assumption will provide the results under the actual conditions.

Reddy, C. Subba↗
NASA NTRS1978

Briefing Materials for Technical Presentations, Volume B: The LACIE Symposium

Tables, charts, and LACIE segments are used to demonstrate the accuracy of estimated crop conditions and yield from 1974 to 1976, and to demonstrate the benefits of meteorological and LANDSAT data. Developments in data acquisition, sampling, and reduction are reviewed. The USDA application test system is highlighted with emphasis on user requirements, technology transfer, data base design, and cost data models for data base operation and management.

Source record↗
NASA NTRS1998

Holographic Storage as a Solution to Space Imaging Requirements

The data growth experienced in the recent past has been of staggering proportions. Over the past 10 years, tape data storage density (with the same form factor) has increased according to Moore's law, doubling every 18 months. However, during the same period, data transfer speeds have only increased at a rate of about 1.3 times every 18 months, and thus have fallen behind data density growth rates by a factor of at least 3. Coupled with data media density growth, data storage requirements have gone up significantly. According to a recent Computer Technology Review article (March 1998) the total storage at a typical Fortune 1000 site is projected to escalate from just 10 TB in 1997 to 1 PB by the year 2000. In the next 5 years, a typical large database system for U.S. government agencies is expected to accept 5 TB per day, maintain 300 TB on-line (within 15 seconds to 1 minute access time), and archive from 15 to 100 PB. Additionally, data intensive programs such as NASA's Earth Observation System (EOS) and the intelligence data archival systems at the Rome Air Development Center, and scientific laboratories such as Thomas Jefferson National Accelerator Facility will have enormously large scientific databases with very large storage requirements.

Halem, Milton↗
NASA NTRS2016

The Geostationary Operational Satellite R Series SpaceWire Based Data System

The Geostationary Operational Environmental Satellite R-Series Program (GOES-R, S, T, and U) mission is a joint program between National Oceanic & Atmospheric Administration (NOAA) and National Aeronautics & Space Administration (NASA) Goddard Space Flight Center (GSFC). SpaceWire was selected as the science data bus as well as command and telemetry for the GOES instruments. GOES-R, S, T, and U spacecraft have a mission data loss requirement for all data transfers between the instruments and spacecraft requiring error detection and correction at the packet level. The GOES-R Reliable Data Delivery Protocol (GRDDP) [1] was developed in house to provide a means of reliably delivering data among various on board sources and sinks. The GRDDP was presented to and accepted by the European Cooperation for Space Standardization (ECSS) and is part of the ECSS Protocol Identification Standard [2]. GOES-R development and integration is complete and the observatory is scheduled for launch November 2016. Now that instrument to spacecraft integration is complete, GOES-R Project reviewed lessons learned to determine how the GRDDP could be revised to improve the integration process. Based on knowledge gained during the instrument to spacecraft integration process the following is presented to help potential GRDDP users improve their system designs and implementation.

Networks↗
NASA NTRS2004

Boiling Heat Transfer Mechanisms in Earth and Low Gravity: Boundary Condition and Heater Aspect Ratio Effects

Boiling is a complex phenomenon where hydrodynamics, heat transfer, mass transfer, and interfacial phenomena are tightly interwoven. An understanding of boiling and critical heat flux in microgravity environments is of importance to space based hardware and processes such as heat exchange, cryogenic fuel storage and transportation, electronic cooling, and material processing due to the large amounts of heat that can be removed with relatively little increase in temperature. Although research in this area has been performed in the past four decades, the mechanisms by which heat is removed from surfaces in microgravity are still unclear. Recently, time and space resolved heat transfer data were obtained in both earth and low gravity environments using an array of microheaters varying in size between 100 microns to 700 microns. These heaters were operated in both constant temperature as well as constant heat flux mode. Heat transfer under nucleating bubbles in earth gravity were directly measured using a microheater array with 100 m resolution operated in constant temperature mode with low and high subcooled bulk liquid along with images from below and from the side. The individual bubble departure diameter and energy transfer were larger with low subcooling but the departure frequency increased at high subcooling, resulting in higher overall heat transfer. The bubble growth for both subcoolings was primarily due to energy transfer from the superheated liquid layer relatively little was due to wall heat transfer during the bubble growth process. Oscillating bubbles and sliding bubbles were also observed in highly subcooled boiling. Transient conduction and/or microconvection was the dominant heat transfer mechanism in the above cases. A transient conduction model was developed and compared with the experimental data with good agreement. Data was also obtained with the heater array operated in a constant heat flux mode and measuring the temperature distribution across the array during boiling. The instantaneous heat transfer into the substrate was numerically determined and subtracted from the supplied heat to obtain the wall to liquid heat flux.

Kim, Jungho↗
NASA NTRS1975

Liquid neon heat transfer as applied to a 30 tesla cryomagnet

Since superconducting magnets cooled by liquid helium are limited to magnetic fields of about 18 teslas, the design of a 30 tesla cryomagnet necessitates forced convection liquid neon heat transfer in small coolant channels. As these channels are too small to handle the vapor flow if the coolant were to boil, the design philosophy calls for suppressing boiling by subjecting the fluid to high pressures. Forced convection heat transfer data are obtained by using a blowdown technique to force the fluid vertically through a resistance-heated instrumented tube. The data are obtained at inlet temperatures between 28 and 34 K and system pressures between 28 to 29 bars. Data correlation is limited to a very narrow range of test conditions, since the tests were designed to simulate the heat transfer characteristics in the coolant channels of the 30 tesla cryomagnet concerned. The results can therefore be applied directly to the design of the magnet system.-

Papell, S. S.↗
NASA NTRS1989

Development of an intelligent interface for adding spatial objects to a knowledge-based geographic information system

Earth Scientists lack adequate tools for quantifying complex relationships between existing data layers and studying and modeling the dynamic interactions of these data layers. There is a need for an earth systems tool to manipulate multi-layered, heterogeneous data sets that are spatially indexed, such as sensor imagery and maps, easily and intelligently in a single system. The system can access and manipulate data from multiple sensor sources, maps, and from a learned object hierarchy using an advanced knowledge-based geographical information system. A prototype Knowledge-Based Geographic Information System (KBGIS) was recently constructed. Many of the system internals are well developed, but the system lacks an adequate user interface. A methodology is described for developing an intelligent user interface and extending KBGIS to interconnect with existing NASA systems, such as imagery from the Land Analysis System (LAS), atmospheric data in Common Data Format (CDF), and visualization of complex data with the National Space Science Data Center Graphics System. This would allow NASA to quickly explore the utility of such a system, given the ability to transfer data in and out of KBGIS easily. The use and maintenance of the object hierarchies as polymorphic data types brings, to data management, a while new set of problems and issues, few of which have been explored above the prototype level.

Campbell, William J.↗
NASA NTRS1992

Structural Tailoring/Analysis for Hypersonic Components - A computational simulation

The development of STAHYC (Structural Tailoring/Analysis for Hypersonic Components), a numerical tool for the optimum design of an engine inlet wall panel for hypersonic aerospace vehicles, is described. STAHYC integrates FORTRAN modules of different disciplines, including fluid dynamics, heat transfer, structural analysis, and optimization. The discussion covers the system design concept, system components, system automation, system testing, established links, and data transfer between different computational modules. The various algorithms used in STAHYC are also discussed.

Narayanan, G. V.↗
NASA NTRS2012

Lunar Reconnaissance Orbiter (LRO) Command and Data Handling Flight Electronics Subsystem

A document describes a high-performance, modular, and state-of-the-art Command and Data Handling (C&DH) system developed for use on the Lunar Reconnaissance Orbiter (LRO) mission. This system implements a complete hardware C&DH subsystem in a single chassis enclosure that includes a processor card, 48 Gbytes of solid-state recorder memory, data buses including MIL-STD-1553B, custom RS-422, SpaceWire, analog collection, switched power services, and interfaces to the Ka-Band and S-Band RF communications systems. The C&DH team capitalized on extensive experience with hardware and software with PCI bus design, SpaceWire networking, Actel FPGA design, digital flight design techniques, and the use of VxWorks for the real-time operating system. The resulting hardware architecture was implemented to meet the LRO mission requirements. The C&DH comprises an enclosure, a backplane, a low-voltage power converter, a single-board computer, a communications interface board, four data storage boards, a housekeeping and digital input/output board, and an analog data acquisition board. The interfaces between the C&DH and the instruments and avionics are connected through a SpaceWire network, a MIL-STD-1553 bus, and a combination of synchronous and asynchronous serial data transfers over RS-422 and LVDS (low-voltage differential-signaling) electrical interfaces. The C&DH acts as the spacecraft data system with an instrument data manager providing all software and internal bus scheduling, ingestion of science data, distribution of commands, and performing science operations in real time.

Nguyen, Quang↗
NASA NTRS2014

Centering a DDR Strobe in the Middle of a Data Packet

The Orion CEV Northstar ASIC (application- specific integrated circuit) project required a DDR (double data rate) memory bus driver/receiver (DDR PHY block) to interface with external DDR memory. The DDR interface (JESD79C) is based on a source synchronous strobe (DQS\) that is sent along with each packet of data (DQ). New data is provided concurrently with each edge of strobe and is sent irregularly. In order to capture this data, the strobe needs to be delayed and used to latch the data into a register. A circuit solves the need for training a DDR PRY block by incorporating a PVT-compensated delay element in the strobe path. This circuit takes an external reference clock signal and uses the regular clock to calibrate a known delay through a data path. The compensated delay DQS signal is then used to capture the DQ data in a normal register. This register structure can be configured as a FIFO (first in first out), in order to transfer data from the DDR domain to the system clock domain. This design is different in that it does not rely upon the need for training the system response, nor does it use a PLL (phase locked loop) or a DLL (delay locked loop) to provide an offset of the strobe signal. The circuit is created using standard ASIC building blocks, plus the PVT (process, voltage, and temperature) compensated delay line. The design uses a globally available system clock as a reference, alleviating the need to operate synchronously with the remote memory. The reference clock conditions the PVT compensated delay line to provide a pre-determined amount of delay to any data signal that passes through this delay line. The delay line is programmed in degrees of offset, so that one could think of the clock period representing 360deg of delay. In an ideal environment, delaying the strobe 1/4 of a clock cycle (90deg) would place the strobe in the middle of the data packet. This delayed strobe can then be used to clock the data into a register, satisfying setup and hold requirements of the system.

Johnson, Michael↗
NASA NTRS2019

HelioSwarm: Swarm Mission Design in High Altitude Orbit for Heliophysics

Resolving the complex three-dimensional turbulent structures that characterize the solar wind requires contemporaneous spatially and temporally distributed measurements. HelioSwarm is a mission concept that will deploy multiple, co-orbiting satellites to use the solar wind as a natural laboratory for understanding the fundamental, universal process of plasma turbulence. The HelioSwarm transfer trajectory and science orbit use a lunar gravity assist to deliver the ESPA-class nodes attached to a large data transfer hub to a P/2 lunar resonant orbit. Once deployed in the science orbit, the free-flying, propulsive nodes use simple Cartesian relative motion patterns to establish baseline separations both along and across the solar wind flow direction.

lunar resonant orbit↗
NASA NTRS2019

HelioSwarm: Swarm Mission Design in High Altitude Orbit for Heliophysics

Resolving the complex three-dimensional turbulent structures that characterize the solar wind requires contemporaneous spatially and temporally distributed measurements. HelioSwarm is a mission concept that will deploy multiple, co-orbiting satellites to use the solar wind as a natural laboratory for understanding the fundamental, universal process of plasma turbulence. The HelioSwarm transfer trajectory and science orbit use a lunar gravity assist to deliver the ESPA-class nodes attached to a large data transfer hub to a P/2 lunar resonant orbit. Once deployed in the science orbit, the free-flying, propulsive nodes use simple Cartesian relative motion patterns to establish baseline separations both along and across the solar wind flow direction.

lunar resonant orbit↗
NASA NTRSDate not supplied

Crew Health and Performance Integrated Data System Platform Project Updates

Future human exploration missions introduce a new paradigm as crews move further from the resupply and near real-time ground support typical of Low Earth Orbit missions today. Without immediate support from ground-based personnel, exploration crews will be more reliant on inflight data and technology to respond to emergencies and anomalies. Today, in-flight data is often siloed, unsynchronized, and largely inaccessible in real time. Many data sets require manual entry and/or data transfer between vehicles and the ground. These issues contribute to risks in supporting crew autonomy for future exploration missions. An integrated data system platform is needed to mitigate these risks by supporting a new generation of technologies and employing advanced analytical and predictive modeling techniques to enable crew autonomy for future exploration missions. The Crew Health and Performance Integrated Data System Platform (CHP-IDSP) project is laying a foundation for future in-flight informatics by providing a back-end architecture for collecting, storing, and integrating multiple sources of data generated by and around the crew. This cohesive integration point will streamline the management of CHP data (e.g., environmental, exercise, medical, sleep, performance, etc.) and facilitate situation awareness and decision support required by the crew and remote support of exploration missions. This presentation will describe the ongoing development effort of the path-to-flight CHP-IDSP software and the demonstration of its core capabilities. This includes a brief history of the project, the human-centered process used to identify data needs and workflows feeding the development of scenarios and requirements, and current subsystem development status. Current integrations, including the Chiron exploration electronic health record application, will be discussed. Future work includes collaboration with additional CHP domains and a flight technology demonstration.

Data integration↗
NASA NTRSDate not supplied

Crew Health and Performance Integrated Data Service Platform (CHP-IDSP): Project Updates

Future human exploration missions introduce a new paradigm as crews move further from the resupply and near real-time ground support typical of Low Earth Orbit missions today. Without immediate support from ground-based personnel, exploration crews will be more reliant on inflight data and technology to respond to emergencies and anomalies. Today, in-flight data is often siloed, unsynchronized, and largely inaccessible in real time. Many data sets require manual entry and/or data transfer between vehicles and the ground. These issues contribute to risks in supporting crew autonomy for future exploration missions. An integrated data services platform is needed to mitigate these risks by supporting a new generation of technologies and employing advanced analytical and predictive modeling techniques to enable crew autonomy for future exploration missions. The Crew Health and Performance Integrated Data System Platform (CHP-IDSP) project is laying a foundation for future in-flight informatics by providing a back-end architecture for collecting, storing, and integrating multiple sources of data generated by and around the crew. This cohesive integration point will streamline the management of CHP data (e.g., environmental, exercise, medical, sleep, performance, etc.) and facilitate situation awareness and decision support required by the crew and remote support of exploration missions. This presentation will describe the ongoing development effort of the path-to-flight CHP-IDSP software and the demonstration of its core capabilities. This includes a brief history of the project, the human-centered process used to identify data needs and workflows feeding the development of scenarios and requirements, and current subsystem development status. Current integrations, including the Chiron exploration electronic health record application, will be discussed. Future work includes collaboration with additional CHP domains and a flight technology demonstration.

Software↗
NASA NTRS1987

Digital Autonomous Terminal Access Communication (DATAC) system

In order to accommodate the increasing number of computerized subsystems aboard today's more fuel efficient aircraft, the Boeing Co. has developed the DATAC (Digital Autonomous Terminal Access Control) bus to minimize the need for point-to-point wiring to interconnect these various systems, thereby reducing total aircraft weight and maintaining an economical flight configuration. The DATAC bus is essentially a local area network providing interconnections for any of the flight management and control systems aboard the aircraft. The task of developing a Bus Monitor Unit was broken down into four subtasks: (1) providing a hardware interface between the DATAC bus and the Z8000-based microcomputer system to be used as the bus monitor; (2) establishing a communication link between the Z8000 system and a CP/M-based computer system; (3) generation of data reduction and display software to output data to the console device; and (4) development of a DATAC Terminal Simulator to facilitate testing of the hardware and software which transfer data between the DATAC's bus and the operator's console in a near real time environment. These tasks are briefly discussed.

Novacki, Stanley M., III↗
NASA NTRS1995

Satellite communications provisions on NASA Ames instrumented aircraft platforms for Earth science research/applications

Earth science activities at NASA Ames are research in atmospheric and ecosystem science, development of remote sensing and in situ sampling instruments, and their integration into scientific research platform aircraft. The use of satellite communications can greatly extend the capability of these agency research platform aircraft. Current projects and plans involve satellite links on the Perseus UAV and the ER-2 via TDRSS and a proposed experiment on the NASA Advanced Communications Technology Satellite. Provisions for data links on the Perseus research platform, via TDRSS S-band multiple access service, have been developed and are being tested. Test flights at Dryden are planned to demonstrate successful end-to-end data transfer. A Unisys Corp. airborne satcom STARLink system is being integrated into an Ames ER-2 aircraft. This equipment will support multiple data rates up to 43 Mb/s each via the TDRS S Ku-band single access service. The first flight mission for this high-rate link is planned for August 1995. Ames and JPL have proposed an ACTS experiment to use real-time satellite communications to improve wildfire research campaigns. Researchers and fire management teams making use of instrumented aircraft platforms at a prescribed burn site will be able to communicate with experts at Ames, the U.S. Forest Service, and emergency response agencies.

Shameson, L.↗
NASA NTRS1960

A Visual Technique for Determining Qualitative Aerodynamic Heating Rates on Complex Configurations

An experimental investigation was conducted at a test-section Mach number of 4.95 and a stagnation temperature of 400 F to evaluate a visual technique for obtaining qualitative aerodynamic heat-transfer data on complex configurations.This technique utilized a temperature-sensetive paint indicated that this technique was satisfactory for determining qualitative heat-transfer rates on various bodies, some of which exhibited complex flow patterns. The results obtained have been found useful to guide the instrumentation of quantitative heat-transfer models, to supplement quantitative heat-transfer measurements, and to make preliminary heat-transfer studies for new configurations.

P. Calvin Stainback↗