Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DEFORMATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Analysis of Deformation and Fracture Mechanisms in the Harvested High-Dose Baffle-Former Bolt with Stress-Corrosion Cracks Formed While in Service

This report presents the results of advanced mechanical testing conducted on miniature tensile specimens excised from an irradiated baffle-former bolt, a commercial pressurized water reactor component. The specimens were extracted from the midsection of the bolt shank, where the estimated damage dose reached 23 displacements per atom. The mechanical testing included the following tests: (1) conventional tensile testing at room temperature, augmented by digital image correlation (DIC) to enable noncontact strain measurements, and (2) in situ tensile testing within a scanning electron microscopy (SEM) instrument equipped with energy-dispersive x-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD) detectors to evaluate active deformation and fracture mechanisms. Additionally, SEM fractographic analysis revealed alterations in the fracture mechanism from a predominantly ductile fracture in nonirradiated steel to a mixed fracture mode (still dominating ductile and minor cleavage spots) in irradiated specimens derived from the baffle bolts. The findings indicate a complex strain localization behavior for in-service irradiated steel specimens. Beyond conventional necking at the macro scale and defect-free channel formation at the micro scale, DIC results identified the presence of deformation bands approximately 100 μm in width. These bands consist of chains of grains exhibiting elevated local strain levels and may be considered an intermediate or mesoscale level of strain localization. These bands become discernible near the yield stress as localized hot spots, areas of elevated strain, persisting throughout most of the experiment. The formation of mesoscale deformation bands as a strain localization mechanism may exacerbate the defect-free channel formation in irradiated materials, further promoting irradiation-assisted stress corrosion crack initiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Monte Carlo Simulation and Reconstruction: Assessment of Myocardial Perfusion Imaging of Tracer Dynamics With Cardiac Motion Due to Deformation and Respiration Using Gamma Camera With Continuous Acquisition

Purpose: Myocardial perfusion imaging (MPI) with single photon emission computed tomography (SPECT) is routinely used for stress testing in nuclear medicine. Recently, our group extended its potential going from 3D visual qualitative image analysis to 4D spatiotemporal reconstruction of dynamically acquired data to capture the time variation of the radiotracer concentration and the estimated myocardial blood flow (MBF) and coronary flow reserve (CFR). However, the quality of reconstructed image is compromised due to cardiac deformation and respiration. The work presented here develops an algorithm that reconstructs the dynamic sequence of separate respiratory and cardiac phases and evaluates the algorithm with data simulated with a Monte Carlo simulation for the continuous image acquisition and processing with a slowly rotating SPECT camera. Methods: A clinically realistic Monte Carlo (MC) simulation is developed using the 4D Extended Cardiac Torso (XCAT) digital phantom with respiratory and cardiac motion to model continuous data acquisition of dynamic cardiac SPECT with slowly rotating gamma cameras by incorporating deformation and displacement of the myocardium due to cardiac and respiratory motion. We extended our previously developed 4D maximum-likelihood expectation-maximization (MLEM) reconstruction algorithm for a data set binned from a continuous list mode (LM) simulation with cardiac and respiratory information. Our spatiotemporal image reconstruction uses splines to explicitly model the temporal change of the tracer for each cardiac and respiratory gate that delineates the myocardial spatial position as the tracer washes in and out. Unlike in a fully list-mode data acquisition and reconstruction the accumulated photons are binned over a specific but very short time interval corresponding to each cardiac and respiratory gate. Reconstruction results are presented showing the dynamics of the tracer in the myocardium as it continuously deforms. These results are then compared with the conventional 4D spatiotemporal reconstruction method that models only the temporal changes of the tracer activity. Mean Stabilized Activity (MSA), signal to noise ratio (SNR) and Bias for the myocardium activities for three different target-to-background ratios (TBRs) are evaluated. Dynamic quantitative indices such as wash-in (K1) and wash-out (k2) rates at each gate were also estimated. Results: The MSA and SNR are higher with higher TBRs while biases were improved with higher TBRs to less than 10%. The correlation between exhalation-inhalation sequence with the ground truth during respiratory cycle was excellent. Our reconstruction method showed better resolved myocardial walls during diastole to systole as compared to the ungated 4D image. Estimated values of K1 and k2 were also consistent with the ground truth. Conclusion: The continuous image acquisition for dynamic scan using conventional two-head gamma cameras can provide valuable information for MPI. Our study demonstrated the viability of using a continuous image acquisition method on a widely used clinical two-head SPECT system. Our reconstruction method showed better resolved myocardial walls during diastole to systole as compared to the ungated 4D image. Precise implementation of reconstruction algorithms, better segmentation techniques by generating images of different tissue types and background activity would improve the feasibility of the method in real clinical environment.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

System and method for simulation-assisted additive manufacturing involving estimating anisotropic deformation

A simulation-assisted additive manufacturing system and method for generating an anisotropic compensation to account for non-uniform deformation due to additive manufacturing and service loading. The predicted deformation may not be fully defined. The present disclosure provides a system and method for estimating the missing deformation data through regression analysis. The present disclosure also provides an integrated framework where the various simulated-assisted design modules are configured for two-way communication and sharing access to changes to the model.

Kim, Seokpum↗
DOE OSTI2023

Voltage‐Modulated Untwist Deformations and Multispectral Optical Effects from Ion Intercalation into Chiral Ceramic Nanoparticles

Abstract Reconfiguration of chiral ceramic nanostructures after ion intercalation should favor specific nanoscale twists leading to strong chiroptical effects. In this work, V 2 O 3 nanoparticles are shown to have “built‐in” chiral distortions caused by binding of tartaric acid enantiomers to the nanoparticle surface. As evidenced by spectroscopy/microscopy techniques and calculations of nanoscale chirality measures, the intercalation of Zn 2+ ions into the V 2 O 3 lattice results in particle expansion, untwist deformations, and chirality reduction. Coherent deformations in the particle ensemble manifest as changes in sign and positions of circular polarization bands at ultraviolet, visible, mid‐infrared (IR), near‐IR (NIR), and IR wavelengths. The g‐ factors observed for IR and NIR spectral diapasons are ≈100–400 times higher than those for previously reported dielectric, semiconductor, and plasmonic nanoparticles. Nanocomposite films layer‐by‐layer assembled (LBL) from V 2 O 3 nanoparticles reveal cyclic‐voltage‐driven modulation of optical activity. Device prototypes for IR and NIR range problematic for liquid crystals and other organic materials are demonstrated. High optical activity, synthetic simplicity, sustainable processability, and environmental robustness of the chiral LBL nanocomposites provide a versatile platform for photonic devices. Similar reconfigurations of particle shapes are expected for multiple chiral ceramic nanostructures, leading to unique optical, electrical, and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength, deformation, and equation of state of tungsten carbide to 66 GPa

Here, strength, texture, and equation of state of hexagonal tungsten monocarbide (WC) have been determined under quasi-hydrostatic and non-hydrostatic compression to 66 GPa using angle-dispersive X-ray diffraction in the diamond anvil cell. Quasi-hydrostatic compression in a Ne pressure medium demonstrates that nanocrystalline WC is slightly less incompressible than bulk-scale WC, with respective bulk moduli of K 0 = 377 ± 7 and 397 ± 7 GPa and pressure derivatives K 0 ’ = 3.8 ± 0.3 and 3.7 ±0.3. This decrease in incompressibility with grain size is similar to behavior observed in other ceramics. Under nonhydrostatic compression, WC supports a mean differential stress of ~12-15 GPa at plastic yielding, which occurs at ~30 GPa. Strength in WC is anisotropic, with the (001) plane supporting 29-42% higher stress than stresses calculated from mean strain. Simulations using an Elasto-ViscoPlastic Self-Consistent model indicate that strength inferred from lattice strain theory may be overestimated due to effects of plastic deformation. Plastic deformation generates a texture maximum near $\langle\bar{2}110\rangle$ in the compression orientation, initially through prismatic slip on the {$10\bar{1}0$}$\langle\bar{1}2\bar{1}0\rangle$ and {$10\bar{1}0$}$\langle0001\rangle$ slip systems, followed by activation of pyramidal slip on {$10\bar{1}1$}$\langle\bar{2}113\rangle$ at ~40-50 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-temperature deformation mechanisms in a BCC+B2 refractory complex concentrated alloy

The current study reports the analysis of the deformation mechanisms at 600 °C in a two-phase, BCC+B2, refractory complex concentrated alloy (RCCA) Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr. At this temperature, the alloy microstructure is unstable and dynamic coarsening of B2 precipitates is evidenced during the mechanical testing. After true plastic strain of 0.030 at strain rate of 10 -4 s -1 , the deformation becomes highly localized in wavy bands reflecting the profusion of cross-slip. Scanning transmission electron microscopy (STEM) observations highlight the presence of paired a/2$\langle$111$\rangle$ dislocations that shear the B2 precipitates in a cooperative process. Additionally, some chemical segregation effect is observed along the narrow dislocation bands likely induced to decrease the antiphase boundary (APB) energy of the system.

ordering↗
DOE OSTI2022

Role of interfaces on phase formation during severe plastic deformation

The role of interfaces on phase formation during severe plastic deformation (SPD) was investigated using molecular dynamics simulations. It is found that dilute solute additions that segregate to interphase boundaries, and strengthen them, can greatly extend the solubility limits of the bounding phases at steady state, providing a novel approach to processing nanocomposite alloys by SPD. Here, the results are rationalized in terms of a modified effective temperature model, whereby increasing the interface strength leads to higher effective temperatures and correspondingly to higher solubilities. Comparison of the segregation coefficient at the interphase boundary with solubilities in the bounding phases illustrates the effective temperature model is self-consistent and comprehensive. Past experimental studies on severe plastic deformation are found consistent with these observations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Variationally consistent Maxwell stress in flexoelectric structures under finite deformation and immersed in free space

Maxwell stress refers to the mechanical stress exerted on a dielectric material due to the presence of electric fields. It plays a significant role in the interaction between a dielectric material and the surrounding free space under finite deformation. Previous research on finite deformation of flexoelectricity mainly adopted a modified form of Maxwell stress, potentially not able to correctly capture some physical phenomena, such as the compression of a dielectric droplet in an electric field. In this work, we propose a consistent and complete variational principle for flexoelectricity, in which the Maxwell stress emerges naturally from the derivation, without introducing additional assumptions. An Isogeometric analysis-based numerical framework is developed accordingly and verified by both linear and nonlinear benchmark cases compared with experimental results. The present framework successfully captures and quantifies the behaviors of conductive liquids and soft dielectric solids subjected to an external electric field. Finally, a novel scenario is investigated in which a flexoelectric beam immersed in free space is analyzed, showing the interesting distribution of Maxwell stress-induced tractions at opposing boundaries. The test demonstrates that a higher dielectric constant can effectively enhance the material's stiffness in response to the external electric loading.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation of pores in response to uniaxial and hydrostatic stress cycling in Marcellus Shale: Implications for gas recovery

One of the main challenges during gas production from shale reservoirs is low recovery rate. One contributing factor to this outcome is an insufficient understanding of pore systems, especially pore behaviour following changes in reservoir conditions or resulting from gas production practices. Because the pressure in the producing well can be controlled, understanding the effects of pressure variation on the pore size distribution and methane trapping is necessary to help design optimal conditions to improve the gas recovery rate. This work is the first systematic study of sub-millimeter pore deformation in shale caused by uniaxial and hydrostatic stress up to 100 MPa. Overmature samples from the Middle Devonian Marcellus Shale were analyzed using neutron scattering (SANS and USANS) techniques to interpret the response of nanopores to stress cycling of magnitude and duration compatible with the hydraulic fracturing treatments. Experiments reported here are performed at a series of uniaxial pressures up to 100 MPa and at hydrostatic pressures of deuterated methane 0 and 50 MPa. Since at the original depth of the shale samples’ burial of 2184 m the hydrostatic pressure is approximately 27 MPa and the lithostatic pressure is about 55 MPa, the experimental conditions reasonably well simulate the reservoir pressure regime. Our SANS and USANS results show that different pore sizes are affected by uniaxial stress in different ways. Specifically, in the pore size range from 1 nm to 800 nm, a decrease of pore density with pressure is observed, with the most depleted being mesopores of about 100 nm in diameter. The observed decrease is likely related to deformation of kerogen, followed by a loss of pore nano-volume, as well as methane trapped in the micropores. For pores larger than 5 μm, USANS data suggest that the negative trend is reversed at above 74 MPa, and the number density of large macropores may increase with increased stress even above the original value. The increased number of macropores at high pressure may create new interconnected conduits for gas migration, resulting in a better recovery rate. Another important finding of this study is an irreversible rearrangement of pore size distribution taking place after pressure cycling. Furthermore, this irreversible reorganization of pore size distribution should be taken into account during management of well production to maximize recovery rate.

03 NATURAL GAS↗
DOE OSTI2022

Comparison of three state-of-the-art crystal plasticity based deformation twinning models for magnesium alloys

In magnesium alloys, deformation twinning and its interactions with dislocation slip are responsible for a sigmoidal shape stress–strain behavior and an asymmetrical tension–compression yield strength in magnesium alloys. The sensitivity of twinning to the underlying microstructure renders the crystal plasticity method the most commonly adopted modeling approach for magnesium-twinning. This paper compares three state-of-the-art crystal plasticity-based twinning models from the literature, namely the elastic-viscoplastic self-consistent twinning-detwinning (EVPSC-TDT) model, crystal plasticity finite element model based on enhanced predominate twin reorientation approach (CPFE-ePTR), and the crystal plasticity finite element model based on “discrete twinning” approach (CPFE-DT). A polycrystalline microstructure is simulated with all three methods to compare the resulting stress–strain curves and lattice strains to those from the experimentally measured data. All three methods showed the capability of capturing the experimental results with different levels of accuracy. Additionally, the EVPSC-TDT method avoids solving the finite element matrices and showed the highest computational efficiency. The CPFE-ePTR model shows a higher accuracy in capturing the lattice strain. The CPFE-DT relies on high-resolution finite element mesh and is much slower than the other two methods, but it captured the local deformation concentration and stress reversal phenomena near the twin band, which was not possible with the other two methods. Based on the comparison, guidance for the selection of the appropriate model based on the specific modeling target is provided in this paper.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A scale-invariant bonded particle model for simulating large deformation and failure of continua

In this paper, a scale-invariant bond model for simulating two-dimensional large deformation of continua is presented. An accurate torque form caused by relative rotation between bonded particles is derived based on beam theory. Validations of the proposed bond model are carried out by large deformation simulations of a simply supported beam subjected to central loading and a cantilever beam with end loading. Comparison of simulations with analytical solutions show a very good agreement. Later, Brazilian tests are simulated to demonstrate the ability of the framework to model failure and fracture process of rock.

58 GEOSCIENCES↗
DOE OSTI2020

Phase field modeling of discontinuous dynamic recrystallization in hot deformation of magnesium alloys

We have developed a quantitative phase field model of discontinuous dynamic recrystallization (PF-DDRX) for investigating grain structure evolution and its impact on mechanical response in magnesium alloy during hot deformation. A set of isothermal compression tests were conducted by Gleeble thermo-mechanical simulator and used to determine PF-DDRX model parameters such as critical stresses of recrystallization, activation energies of dislocation, grain boundaries and recrystallization grain nucleation. In the simulations, the experimentally measured average grain size and distribution were used to generate initial microstructures. The results show that the typical ‘necklace’ microstructures observed in DDRX forms at the earlier stage of recrystallization. The inhomogeneity of microstructures first increases rapidly and then decreases gradually and reaches a constant with the increase of dynamic recrystallization volume fraction. Both predicted grain structure and mechanical response are in good agreement with experimental results. This demonstrates that the model parameters determined by experimental data are reliable for the developed PF-DDRX model to predict the grain structure evolution and flow behavior of AZ80 magnesium alloy under hot deformation. This work presents a path to combine experiments and modeling to give quantitative prediction and minimize experimental cost.

magnesium alloy, Phase field method, dynamic recry↗
DOE OSTI2023

Microstructure characterization and elastic-plastic self-consistent simulation studies of anisotropic deformation of β -tin

Uniaxial compression tests of 99.9% pure polycrystalline $β$-tin (Sn) were conducted at various strain rates (10 -3 /s, 10 -1 /s and 1/s) and temperatures (294 K and 193 K) to understand the effects of these variables on the stress–strain response, microstructure evolution, and stress relaxation behavior. Multiple Sn specimens were subjected to complex compressive loading/unloading/reloading paths at different strain rates. Specimens initially compressed at higher strain rates showed strain rate-dependent texture evolution and more pronounced relaxation upon reloading, as compared to those pre-strained at lower rates at room temperature (RT). Compression tests conducted at low temperature (193 K) revealed increased strength, similar to the enhanced strength observed when the strain rate was increased at RT. Neutron diffraction was employed to characterize the initial and final bulk textures of the RT specimens. Electron backscatter diffraction was utilized to examine the crystallographic grain orientation and morphology, thereby identifying the signatures of dislocation-mediated deformation, grain refinement, recrystallization, and twinning behaviors. Elastic-plastic self-consistent simulations were performed to investigate the deformation modes responsible for the strain rate-dependent macroscopic stress–strain response and texture evolution. Effects of crystallographic orientation on stress relaxation behavior was also examined. In conclusion, the model predictions are in reasonable agreement with experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A prediction model of failure threshold for shear deformation in a Zr-based bulk metallic glass

The failure of bulk metallic glasses (BMGs) during plastic deformation at room temperature is abrupt and instantaneous, while the analysis of precursor information based on avalanche events helps predict catastrophic failure. An acoustic emission (AE) signal can provide accurate precursor information for material failure, due to its sensitive and high fast calculation ability. In the current study, AE monitoring tests are carried out during uniaxial compression tests of BMGs at different strain rates. The AE experimental failure threshold, E max , is proposed on the basis of AE cumulative energy, which reflects the intensity of damage evolution at different loading conditions. Compared with the critical shear band velocity (CSBV) associated with stick-slip dynamics of serrated flow, E max is a more sensitive failure parameter since it is connected with the local microscopic changes that occur during the material response process. Here, the E max is obtained prior to reaching the CSBV since the calculation of these two avalanches analysis focuses on the different stages of shear band growth. In particular, AE events are related to the “dry” friction process in the first stage, however, the CSBV is responsible for the “viscous” glide in the second stage. Therefore, Emax is not affected by the complex interactions between the shear bands during the stick-slip process. The maximum avalanche of serrated flow, S max , is proposed as the experimental failure threshold, which depends on the applied strain rate as S max ~ $\dot{ε}$ –λ . According to the relationship of E max and S max , the theoretical failure threshold, E max , follows a criterion E max = 2545$\dot{ε}$ –λ - 4468, where λ is equivalent to 0.15 for this work. Finally, combining the different calculations and AE measurements, this model gives new insights to predict the deformation failure behavior of Zr-based BMGs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation behavior of a Co-Cr-Fe-Ni-Mo medium-entropy alloy at extremely low temperatures

In this work, we report the mechanical and microstructural characteristics of a medium-entropy alloy, Co 17.5 Cr 12.5 Fe 55 Ni 10 Mo 5 (atomic percent, at%) at cryogenic temperatures, down to a record low temperature of 0.5 K. The alloy exhibits excellent strength and ductility combined with a high strain-hardening rate in the entire temperature range investigated. Its property profile, including the yield strength, ultimate tensile strength, strain hardening capability, and absorbed mechanical energy, is better than those of most alloys and HEAs used in cryogenics. Within the interval of extremely low temperatures considered (0.5–4.2 K), the alloy exhibits several unusual features, including anomalies of the temperature dependence of the yield strength and tensile ductility, discontinuous plastic deformation (DPF), and a change in the propensity for the deformation-induced martensitic transformation. While the occurrence of these effects in the same temperature interval may be fortuitous, we hypothesize that they are interrelated and provide a tentative explanation of the observed phenomena on this basis.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The effects of free surfaces on deformation twinning in HCP metals

Deformation twinning is a predominant mode of plastic deformation for hexagonal close packed metals, like Mg and Ti. The heterogenous microstructure and the local stresses associated with twinning play a key role in their mechanical response and fracture. Surface analyses, like electron microscopy, are frequently employed to spatially map microstructure and micromechanical fields in order to study twinning behavior. However, these measurements are inherently influenced by the vicinity of the free surface. In this work, an elasto-visco-plastic fast-Fourier-transform (EVP-FFT) polycrystal modeling approach is employed to investigate the effects of free surfaces on twin development before and after loading. We compare calculated micromechanical fields on free surfaces with those calculated inside the bulk and, in some cases, experimental surface measurements. The results indicate that the creation of free surfaces can promote twin propagation and growth and can influence twin morphology by causing a twin lamella to become larger, more blunted and irregular. The structure along the twin boundaries are also affected, due to the higher driving stresses that extend prismatic-basal and basal-prismatic facets. Furthermore, free surfaces invoke different slip activities in the twin and the surrounding parent crystal by enhancing basal, prismatic and pyramidal slip in some localized regions, while reducing slip in others. We demonstrate that the simulated free-surface effects lead to better qualitative and quantitative agreement with experimental measurements from scanning electron microscopy and digital image correlation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Decoupling of strain and temperature effects on microstructural evolution during high shear strain deformation

The interplay between defect generation by shear strain and defect annihilation by local heating is difficult to predict in shear-assisted processing techniques. In this study, we decoupled the effects of high shear strain and external heating in an immiscible Cu-Nb alloy using a pin-on-disk tribometer to mimic the microstructural evolution of material during solid-phase processing. The change in sub-surface deformation, strain distribution, and redistribution of the second phase as a function of temperature were examined using transmission electron microscopy and atom probe tomography. Zener-Hollomon parameter is used to semi-quantify the deformation of Cu-Nb alloys as a function of strain and temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Image registration for in situ X-ray nano-imaging of a composite battery cathode with deformation

The structural and chemical evolution of battery electrodes at the nanoscale plays an important role in affecting the cell performance. Nano-resolution X-ray microscopy has been demonstrated as a powerful technique for characterizing the evolution of battery electrodes under operating conditions with sensitivity to their morphology, compositional distribution and redox heterogeneity. In real-world batteries, the electrode could deform upon battery operation, causing challenges for the image registration which is necessary for several experimental modalities, e.g. XANES imaging. To address this challenge, this work develops a deep-learning-based method for automatic particle identification and tracking. This approach was not only able to facilitate image registration with good robustness but also allowed quantification of the degree of sample deformation. The effectiveness of the method was first demonstrated using synthetic datasets with known ground truth. The method was then applied to an experimental dataset collected on an operating lithium battery cell, revealing a high degree of intra- and interparticle chemical complexity in operating batteries.

25 ENERGY STORAGE↗