Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cross Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Accessing a high‐voltage nonaqueous hybrid flow battery with a sodium‐methylphenothiazine chemistry and a sodium‐ion solid electrolyte

Abstract The development of redox flow batteries (RFBs) with nonaqueous electrolytes offers the possibility of accessing a high cell‐operation voltage (no restrain of hydrogen evolution and oxygen evolution potentials) and a low operation temperature (can be operated below the freezing point of water). Therefore, nonaqueous RFBs have recently garnered increasing attention. However, the cross‐mixing of liquid electrode/electrolyte materials has been plaguing the progress of the nonaqueous RFBs. Herein, we present a crossover‐free, high voltage nonaqueous hybrid flow battery (HFB) with a novel sodium‐methylphenothiazine (MPT) chemistry and a single‐ion solid‐electrolyte separator. The Na‐MPT redox couple delivers a high voltage of ~2.6 V when the cell was operated at a medium current density. A NASICON‐type solid electrolyte membrane (Na 3 Zr 2 Si 2 PO 12 ) could circumvent the crossover of the liquids between the positive and negative electrodes, and meanwhile could maintain a single‐ion (Na + ‐ion) conduction between the two electrodes to sustain the electrochemical reactions. Under such an electrochemical mechanism, the nonaqueous Na‐MPT HFB shows remarkable cycling performance.

Yu, Xingwen↗
DOE OSTI2024

Development and experimental evaluation of an acoustic flow meter prototype for measuring air flow

Here, this study outlines the development and testing of a flow meter prototype specifically designed for use in nuclear reactor environments. The meter uses flow-induced vibration to measure flow rates and is designed for remote monitoring in harsh environments where radiation can damage electronics. The device generates a vibration signal produced by a feedback system when fluid flows out of an orifice and interacts with a downstream wedge. The frequency of the vibration signal corresponds directly to flow rate and velocity. The study investigates geometric parameters intrinsic to the prototype, such as orifice height, width, edge distance, and chamber length. Different configurations were also tested, including a bypass loop with variable cross-sections around the device. The investigation results reveal the impact of these geometric parameters on the vibration signal output, providing valuable insights for future design improvements and enhancing the effectiveness of flow metering systems used in nuclear reactor applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

X-ray and gamma-ray tomographic imaging of fuel relocation inside sodium fast reactor test assemblies during severe accidents

The present work reports on x-ray and gamma-ray high-spatial resolution computerized tomography measurements of the Pin Bundle Metallic Fuel Relocation (PBR) assemblies tested in the Metallic Uranium Safety Experiment (MUSE) facility at Argonne National Lab (ANL). The aim of the study was to characterize fuel relocation structures that develop during severe core accidents pertaining to SFR assemblies; these include but are not limited to advanced core disruption recreated in the PBR-1 assembly, and cladding breach recreated in the PBR-2 assembly. We report the x-ray tomography measurements were able to resolve small quantities of relocation fuel; with increased presence of relocation fuel, the x-ray 1measurements spatially mapped the material but could not resolve the inner regions of these. The gamma-tomography measurements showed improved results, resolving the relocation structures in great detail. The upper plenum of the PBR-1 assembly where the molten uranium was initially inserted presented high structural damage, reflected by the partial and complete disintegration of the central rods. Relocation fuel filled the subchannels, adhering to surviving cladding walls and the assembly casing. In the lower portion of the measured section, the tomogram degrades due to photon starvation effects hinting at the increased amount of relocation fuel potentially plugging the assembly; flow blockage in this section was difficult to determine due to the tomogram’s degradation from photon starvation. Small fragments were observed further down the assembly, dislodged from the initial insertion of the molten material. This section was used as an unperturbed assembly reference, with a calculated blockage of less than 1% from the present fragments. The PBR-2 assembly was characterized by columnar relocation structures propagating through the subchannels. Three of the relocation structures were captured in the measured section, with evidence of cross migration on to adjacent subchannels. The measured section in this assembly captures the leading edge of two structures. The calculated flow blockage was 16% in the planes where the three relocation structures are present, but this quickly decreases to approximately 5% past the leading edge of two of the structures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Towards engineering hybrid incompatibility in plants

The potential for gene flow between genetically modified organisms (GMOs) and non-GMO relatives poses a significant challenge to the development and regulatory approval of GMO crops (Wedger et al., 2024), for example, the spread of herbicide resistance transgenes from crops such as rice or sorghum to cross-pollinating weedy species. Addressing this concern, we developed Engineered Genetic Incompatibility (EGI) (Maselko et al., 2017), a system that establishes species-like barriers to gene flow between otherwise sexually compatible populations. EGI employs Programmable Transcriptional Activators (PTAs) to drive lethal over- and/or ectopic expression of tightly regulated genes following undesired hybridization events (Figure 1a,b). A benign mutation of the target promoter in the EGI organism protects it from ill effects of the PTA, which acts as a sentinel for the wild-type (WT) promoter sequence. Given numerous potential PTA targets, multiple mutually incompatible subpopulations are feasible (Maselko et al., 2020). EGI has been demonstrated in yeast as a proof-of-concept (Maselko et al., 2017) and in insects as a strategy for genetic biocontrol of pests (Maselko et al., 2020; Upadhyay et al., 2022). EGI in plants would provide a strategy to halt gene flow between engineered crops and their domestic and wild relatives without altering normal cultivation or propagation practices. Here, we present promising results towards the demonstration of EGI in plants and highlight technical challenges that still need to be overcome.

CRISPRa↗
DOE OSTI2025

Optimizing microfluidic flow cell geometry for in situ resonant soft X-ray characterization of molecular nanostructures

Liquid-phase resonant soft X-ray scattering (LP-RSoXS) is an emerging label-free technique to probe chemically resolved nanostructures of molecular or hybrid materials in liquid environments. Still, quantitative analysis is hindered by the pressure-induced deformation of thin silicon nitride (SiN) membranes used as windows in microfluidic flow cells, which attenuates the signal in nonlinear ways, making experimental optimization difficult. Here, in this work, we directly characterize this deformation under experimental conditions for a variety of cell configurations. We use this to develop a predictive model that combines transmission effects of SiN bowing, incident X-ray beam profiles, and material-dependent resonant scattering cross sections to simulate the effective scattering intensity at the detector across the carbon K-edge. Maps of the total signal across the flow cell window reveal that increasing the window width and polymer concentration shifts the anisotropic intensity distributions from the center toward the edges of the window. It was determined that an optimal SiN thickness of 50 nm, with a window aperture of 104 μm, maximizes the total signal for typical solute concentrations and energies across the carbon K-edge. Our results overturn the assumption that corner regions dominate the scattering signal, offering explicit design guidelines for maximizing LP-RSoXS signals and significantly advancing the quantitative application of this technique to the characterization of molecular and hybrid nanostructured materials in liquids.

Grabner, Devin [Washington State Univ., Pullman, W↗
DOE OSTI2024

Block Polyelectrolyte Additives That Modulate the Viscoelasticity and Enhance the Printability of Gelatin Inks at Physiological Temperatures

We demonstrate the utility of block polyelectrolyte (bPE) additives to enhance viscosity and resolve challenges with the three-dimensional (3D) printability of extrusion-based biopolymer inks. The addition of oppositely charged bPEs to solutions of photocurable gelatin methacryloyl (GelMA) results in complexation-driven self-assembly of the bPEs, leading to GelMA/bPE inks that are printable at physiological temperatures, representing stark improvements over GelMA inks that suffer from low viscosity at 37 °C, leading to low printability and poor structural stability. The hierarchical microstructure of the self-assemblies (either jammed micelles or 3D networks) formed by the oppositely charged bPEs, confirmed by small-angle X-ray scattering, is attributed to the enhancements in the shear strength and printability of the GelMA/bPE inks. Varying bPE concentration in the inks is shown to enable tunability of the rheological properties to meet the criteria of pre- and postextrusion flow characteristics for 3D printing, including prominent yielding behavior, strong shear thinning, and rapid recovery upon flow cessation. Moreover, the bPE self-assemblies also contribute to the robustness of the photo-cross-linked hydrogels; photo-cross-linked GelMA/bPE hydrogels are shown to exhibit higher shear strength than photo-cross-linked GelMA hydrogels. Last, the assessment of the printability of GelMA/bPE inks indicates excellent printing performance, including minimal swelling postextrusion, satisfactory retention of the filament shape upon deposition, and satisfactory shape fidelity of the various printed constructs. We envision this study to serve as a practical guide for the printing of bespoke extrusion inks where bPEs are used as scaffolds and viscosity enhancers that can be emulated in a range of photocurable precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Collisionless adiabatic afterglow

In this work, we study, by numerical and analytical means, the evolution of a collisionless plasma initiated between absorbing walls. The ensuing flow is described by rarefaction waves that travel inward from the boundaries, interact, and eventually vanish after crossing through, leading up to the asymptotic stage of the decay. Particle simulations indicate that the kinetic evolution strongly resembles one found in isentropic gas dynamics. Namely, a very gradual density profile forms in the expanding central region where the rarefaction waves interact, with an accompanying linear velocity profile. Asymptotically, the density falls off as 1/t. The density and the flux at the boundary show little variation over the period when rarefaction waves still exist. Plasma potential, on the other hand, drops quite rapidly (on the underlying ion-acoustic timescale) to less than initial electron temperature Te when over 70% of the particles still remain in the system. This is due to electron kinetics being governed by conservation of adiabatic invariant in a slowly varying potential well. Analytical model of the velocity distribution is presented to explain the simulations. The results have implications for afterglow plasmas used in material processing and also for ion-extraction devices. One property of potential interest is good uniformity of the decaying plasma that occurs after approximately one ion-acoustic time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Refueling water storage tank (RWST) with tailored passive emergency core cooling (ECC) flow

A nuclear reactor comprises a pressure vessel containing a nuclear reactor core. A reactor core cooling system comprises a standpipe including a plurality of orifices in fluid communication with a refueling water storage tank (RWST) to drain water from the RWST into the standpipe, and an injection line configured to drain water from the standpipe to the pressure vessel. In some embodiments the standpipe is disposed in the RWST, while in other embodiments the standpipe is disposed outside of the RWST and cross-connection pipes connect the plurality of orifices with the RWST. The reactor core cooling system may further comprise a valve configured to control flow through one orifice of the plurality of orifices in fluid communication with the RWST based on water level in the standpipe. The valve may comprise a float valve having its float disposed in the standpipe.

Watson, Ronald C.↗
DOE OSTI2025

Theory and simulations of cross-beam energy transfer between speckled laser beams

In this paper, we introduce a realistic modeling of laser beams smoothed by random phase plates to investigate cross-beam energy transfer (CBET). We compute the total field of the smoothed laser beams, which allows us to perform accurate simulations and to build a model accounting for the realistic structure of the speckles. This lets us confirm the results already discussed in a previous work given by Oudin et al. [Phys. Plasmas 29, 112112 (2022)]. When CBET is induced by a plasma flow, plane wave models can predict the exchange between smoothed laser beams. By contrast, when the exchange is caused by a wavelength shift between the laser fields of each beam, plane wave models overestimate the energy transfer, even for strongly Landau-damped ion acoustic waves. We also show that the laser angular spread, which results from its focusing, affects the resonance between the ponderomotive force induced by the laser fields and the ion acoustic wave. It increases the resonance width, which weakly depends on the Landau damping rate when there is a wavelength shift and no flow. In addition, the power transfer obtained with or without a phase plate is essentially the same in the perturbative regime and for small crossing angles.

Laser plasma interactions↗
DOE OSTI2023

Study of the 22 Mg Waiting Point Relevant for X-Ray Burst Nucleosynthesis via the 22 Mg(α,p) 25 Al Reaction

The 22 Mg(α, p) 25 Al reaction rate has been identified as a major source of uncertainty for understanding the nucleosynthesis flow in Type-I x-ray bursts. Here, we report a direct measurement of the energy-and angle-integrated cross sections of this reaction in a 3.3-6.9 MeV center-of-mass energy range using the MUlti-Sampling Ionization Chamber (MUSIC). The new 22 Mg(α, p) 25 Al reaction rate is a factor of ~4 higher than the previous direct measurement of this reaction within temperatures relevant for x-ray bursts, resulting in the 22 Mg waiting point of x-ray burst nucleosynthesis flow to be significantly bypassed via the (α, p) reaction.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Homotypic aggregates contribute to heterogeneity in B cell fates due to an intrinsic gradient of stimulant exposure

Highlights: • CD40-signaled B cells in cultures form three-dimensional homotypic aggregates. • These tight aggregates hinder the free diffusion of large molecule stimulants. • The resulting concentration gradient of stimulants leads to heterogeneous cell fates. • We describe a flow cytometric approach to quantify this positional information. Monocultures of several cell types result in the formation of robust clusters called homotypic aggregates (HAs). How this physical aggregation affects cell fates in immune cell cultures, is poorly understood. We studied anti-CD40-stimulated primary B cell cultures, where cells assembled into large three-dimensional LFA1-driven HAs by 72 h. The dense packing in these aggregates restricts the infiltration of stimulants, such as antibodies, to cells inside the clusters. This creates a concentration gradient of stimulant availability across the cross-section of HAs. We describe a method to retain this positional information even after the disruption of HAs, for analysis by flow cytometry. Comparison of stage-specific cell-surface markers showed that the extent of stimulant-binding affected multiple fates non-uniformly. While germinal center and lineage markers were moderately upregulated, immunoglobulins and markers associated with memory were more than doubled in the peripheral cells binding more anti-CD40. These cells also experienced a strong repression of the plasma cell regulator Prdm1 and an upregulation of the oncogene Myc. Thus, cells at different locations in HAs are subjected to unequal doses of stimulants, leading to a hitherto unreported source of heterogeneity in cell fates. These findings can be extrapolated to understand the dose-dependent effects of stimulants in other three-dimensional cell clusters.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Differential ability of three bee species to move genes via pollen

Since the release of genetically engineered (GE) crops, there has been increased concern about the introduction of GE genes into non-GE fields of a crop and their spread to feral or wild cross-compatible relatives. More recently, attention has been given to the differential impact of distinct pollinators on gene flow, with the goal of developing isolation distances associated with specific managed pollinators. To examine the differential impact of bee species on gene movement, we quantified the relationship between the probability of getting a GE seed in a pod, and the order in which a flower was visited, or the cumulative distance traveled by a bee in a foraging bout. We refer to these relationships as ‘seed curves’ and compare these seeds curves among three bee species. The experiments used Medicago sativa L. plants carrying three copies of the glyphosate resistance (GR) allele as pollen donors (M. sativa is a tetraploid), such that each pollen grain carried the GR allele, and conventional plants as pollen recipients. Different foraging metrics, including the number of GR seeds produced over a foraging bout, were also quantified and contrasted among bee species. The lowest number of GR seeds set per foraging bout, and the GR seeds set at the shortest distances, were produced following leafcutting bee visits. In contrast, GR seeds were found at the longest distances following bumble bee visits. Values for honey bees were intermediate. The ranking of bee species based on seed curves correlated well with field-based gene flow estimates. Thus, differential seed curves of bee species, which describe patterns of seed production within foraging bouts, translated into distinct abilities of bee species to move genes at a landscape level. Bee behavior at a local scale (foraging bout) helps predict gene flow and the spread of GE genes at the landscape scale.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Computational Modeling of Water Infiltration From Ditches Into Roadway Embankments

Ditches are built along roadways to convey the stormwater runoff. They collect the runoff from the pavement and adjacent drainage areas. Water can move freely in a ditch away from the road surface, thus making it safer for the vehicular traffic. South Carolina DOT expressed interest in studying infiltration of water from ditches into roadway embankments. As part of the current design criteria, it is recommended that the road subgrades be 1.0 foot above the design event water surface elevation in the ditch. The distance between the water surface and bottom of the subbase is referred to as “freeboard”. The purpose of this requirement is to lower the risk of pavement damage by moving the flow away from the pavement, containing the captured flow, and conveying flow received from adjacent properties to outfalls. With changes in roadway design standards, larger shoulders and flatter cross-slopes have moved ditches further away from the pavement and the subbase. These changes could allow for a lower freeboard standard without reducing safety margins due to the increased lateral distance from the subbase to the ditch. The objective of this study is to evaluate whether the current SCDOT criterion requiring the roadway subgrade to be 1 ft above the design-event ditch water surface can be relaxed under selected geometric and soil conditions, particularly where larger shoulder widths and flatter side slopes increase horizontal separation between ditch water and pavement structure.

42 ENGINEERING↗
DOE OSTI2022

Crosslinked Polyethyleneimine Gel Polymer Interface to Improve Cycling Stability of RFBs

Redox flow batteries are considered a promising technology for grid energy storage. However, capacity decay caused by crossover of active materials is a universal challenge for many flow battery systems, which are based on various chemistries. In this paper, using the vanadium redox flow battery as an example, we demonstrate a new gel polymer interface (GPI) consisting of crosslinked polyethyleneimine with a large amount of amino and carboxylic acid groups introduced between the positive electrode and the membrane. The GPI functions as a key component to prevent vanadium ions from crossing the membrane, thus supporting stable long-term cycling. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements were conducted to investigate the effect of GPI on the electrochemical properties of graphitic carbon electrodes (GCFs) and redox reaction of catholyte. X-ray photoelectron spectroscopy (XPS) and 1 H nuclear magnetic resonance (NMR) spectra demonstrated that the crosslinked GPI is chemically stable for 100 cycles without dissolution of polymers and swelling in the strong acidic electrolytes. Results from inductively coupled plasma mass spectrometry (ICP-MS), Fourier-transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray (EDX) spectroscopy proved that the GPI is effective in maintaining the concentration of vanadium species in their respective half-cells, resulting in improved cycling stability because of it prevents active species from crossing the membrane and stabilizes the oxidation states of active species.

Lim, Hyung-Seok↗
DOE OSTI2021

An organic bifunctional redox active material for symmetric aqueous redox flow battery

Symmetric redox flow batteries utilizing a single redox active material as catholyte and anolyte, offer a plausible and unique strategy to alleviate cross-contamination issues during cycling, making them an ideal energy storage device for large scale applications. In this work, a low-cost riboflavin organic molecule is coupled with a 2,2,6,6-Tetramethylpiperidinyl-N-oxyl (TEMPO) radical molecule to form a single Riboflavin-TEMPO (RIBOTEMPO) bifunctional redox active material, which is used in both aqueous anolyte and catholyte. Cyclic voltammetry analysis of the combined molecule displays electrochemically reversible reactions for the redox couples at 0.72 V and 0.51 V versus Hg/Hg2SO4, leading to a theoretical cell voltage of 1.23 V. A symmetric cell testing demonstrated over 100 consecutive charge/discharge cycles with nearly 80% coulombic efficiency and capacity retention of 44.7% at a current density of 2.5 mA cm(-2). By utilizing a pH neutral supporting electrolyte, a lowcost, safe, and environmental-friendly redox flow battery is achieved. This work provides a pathway for the design and development of bifunctional redox active molecules for symmetric battery applications.

25 ENERGY STORAGE↗
DOE OSTI2021

A unified theory of zonal flow shears and density corrugations in drift wave turbulence

A unified theory of zonal flow shears and density corrugations in drift wave turbulence is presented. Polarization and density advection beat excitation are studied in combination with modulational response. Noise is driven by two-time flux correlation. While the effective zonal flow eddy viscosity can go negative, the zonal diffusivity is positive definite. There is no inverse cascade of density corrugation. The connection between avalanches and corrugations is discussed. Here, the zonal cross-correlation is identified and calculated. Conditions for alignment of zonal shears and corrugation gradients are determined, and the implications for staircase structure are discussed. We show that the synergy of beat noise and modulational effects is stronger than either alone. Strong zonal flows can be excited well below the modulational instability threshold. In the context of L–H transition, zonal noise quenches turbulence overshoot by eliminating the threshold for zonal flow excitation. The power threshold for L–H transition is lowered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulations of vertical displacement oscillatory modes and global Alfvén Eigenmodes in JET geometry

Vertical Displacement Oscillatory Modes (VDOM), with frequency in the Alfvén range, are natural modes of oscillation of magnetically confined laboratory plasmas with elongated cross-section. These axisymmetric modes arise from the interaction between the plasma current, which is in equilibrium with currents flowing in external coils, and perturbed currents induced on a nearby conducting wall. The restoring force exerted by these perturbed currents on the vertical motion of the plasma column leads to its oscillatory behavior. An analytic model for VDOM was proposed based on an idealized 'straight tokamak' equilibrium with uniform equilibrium current density. This article introduces the first numerical simulations of VDOM in a realistic JET tokamak configuration, using the extended-MHD code NIMROD and drawing comparisons with Global Alfvén Eigenmodes (GAE). The results show qualitative agreement with analytic predictions regarding mode frequency and radial structure, supporting the identification of VDOM as a fundamental oscillation mode in tokamak plasmas. VDOM and GAE are modeled in a representative JET discharge, where axisymmetric perturbations with toroidal mode number n = 0 driven unstable by fast ions were observed. The two modes are examined separately using a forced oscillator within the NIMROD code, which enables a comparison of their characteristics and helps identify the experimentally observed mode possibly as a GAE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

5G Energy FRAME: The Design and Implementation of Data, Model, and Use Case (Year 2 Report)

This report summarizes the Year 2 work of Pacific Northwest National Laboratory’s (PNNL’s) 5G Fabricated Resource and Asset Management Encompassment for energy infrastructure (Energy FRAME) project funded by the Department of Energy Office of Science’s Advanced Scientific Computing Research (ASCR) Program. In this report, newest 5G equipment testing results are presented, along with two 5G-enabled AI/ML examples for grid applications; in addition, the work flow of grid edge, cloud, and High Performance Computing (HPC) platform is introduced, to support and interface the cross-domain simulation for power system transmission, distribution, and communication networks. Last but not least, the outlook for Year 3 work and the overarching impact of 5G Energy FRAME work to a multitude of stakeholders are provided. Additional 5G performance data now is shared through the publicly available weblink, https://www.pnnl.gov/projects/5g-energy-frame/publications

24 POWER TRANSMISSION AND DISTRIBUTION↗