Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Charging Reliability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Voltage Regulators for Photovoltaic Systems

Two simple circuits developed to provide voltage regulation for highvoltage (i.e., is greater than 75 volts) and low-voltage (i.e., is less than 36 volts) photovoltaic/battery power systems. Use of these circuits results in voltage regulator small, low-cost, and reliable, with very low power dissipation. Simple oscillator circuit controls photovoltaic-array current to regulate system voltage and control battery charging. Circuit senses battery (and system) voltage and adjusts array current to keep battery voltage from exceeding maximum voltage.

Delombard, R.↗

[No Title]

Adequate performance was achieved relatively early in the development of ion engines and most subsequent development programs have focussed on demonstrating adequate engine life. The primary threats to engine reliability over the required service life are damage accumulation failure modes such as accelerator grid failure due to sputter erosion from charge exchange ions, erosion of discharge chamber components by lower energy ion sputtering and grid shorting by flakes of sputter-deposited material. These types of failure may typically be observed only after thousands of hours of operation. The purpose of this paper is to provide a critical review of the approaches used in past ion engine development programs to characterize and control these wearout failure mechanisms.

Ion Engine↗

Calibration of the analog beam-signal hardware for the credited engineered beam power limit system at the Proton Power Upgrade Project at the Spallation Neutron Source

A programmable signal processor-based credited safety control that calculates pulsed beam power based on beam kinetic energy and charge was designed as part of the Proton Power Upgrade (PPU) project at the Spallation Neutron Source (SNS). The system must reliably shut off the beam if the average power exceeds 2.145 MW averaging over 60 seconds. System calibration requires pedigree in measurements, calibration setup, and calculations. This paper discusses the calibration of the analog beam signal components up to and including the Analog Digital Convertors (ADCs) for implementation into the Safety Programmable Logic Controllers (PLCs) and Field Programmable Gate Arrays (FPGAs).

Bobrek, Miljko↗

Parametric Performance of a Spiral-Artery, Liquid-Trap-Diode Heat Pipe

A series of parametric investigations are described which determine the effect of various fluid charges on the performance of a 0.635-cm-diam spiral-artery, liquid-trap diode in both the forward and reverse modes. Specific parameters such as forward- and reverse-mode conductances, shutdown times and energies, and recovery to forward-model operation, are evaluated for ethane as a working fluid in the temperature range 170 K to 220 K. Results indicate that the heat pipe will not reliably start up in the forward mode. However, startup can be initiated when preceded by a diode reversal. Also included are data which show the susceptibility of the diode to fluid charge and tilt. The optimum fluid charge was found to be 2.67 g and transport capability at this charge was in excess of 1200 W-cm at 200 K. The diode in the reverse mode exhibited a rapid shutdown (within 9 min) with a shutdown energy of 1150 J (0.32 Wh).

Williams, R. J.↗

Investigation of a cryogenic thermal diode

This paper describes a series of parametric investigations to determine the effect of various fluid charges on the performance of a 0.635-cm-diameter spiral-artery, liquid-trap diode in both the forward and reverse modes. Specific parameters such as forward- and reverse-mode conductances, shutdown times and energies, and recovery to forward-mode operation, are evaluated for ethane as a working fluid in the temperature range 170 K to 220 K. Results indicate that the heat pipe will not reliably start up in the forward mode. However, startup can be initiated when preceded by a diode reversal. Also concluded are data which show the susceptibility of the diode to fluid charge and tilt. The optimum fluid charge was found to be 2.67 g, and transport capability at this charge was in excess of 1200 W-cm at 200 K. The diode in the reverse mode exhibited a rapid shutdown (within 9 min) with a shutdown energy of 1150 J (0.32 Wh).

Williams, R. J.↗

Electrification 2022 Annual Progress Report

The Electric Drive Technologies (EDT) program's mission is to conduct early-stage research and development on transportation electrification technologies that accelerate the development of cost-effective and compact electric traction drive systems that meet or exceed performance and reliability requirements of internal combustion engine (ICE)-based vehicles, thereby enabling electrification across all light-duty vehicle types. The Grid and Charging Infrastructure (G&I) program's mission is to conduct early-stage research and development on transportation electrification technologies that enable reduced petroleum consumption by light, medium, and heavy-duty vehicles. The program identifies and enables the role of vehicles in the future electrical grid.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Electrification (2023 Annual Progress Report)

This document summarizes the progress of VTO Electrification R&D projects supported during the fiscal year 2023. The Electric Drive Technologies (EDT) program’s mission is to conduct early-stage research and development on transportation electrification technologies that accelerate the development of cost-effective and compact electric traction drive systems that meet or exceed performance and reliability requirements of internal combustion engine (ICE)-based vehicles, thereby enabling electrification across all light-duty vehicle types. The Grid and Charging Infrastructure (G&I) program's mission is to conduct early-stage research and development on transportation electrification technologies that enable reduced petroleum consumption by light, medium, and heavy-duty vehicles. The program identifies and enables the role of vehicles in the future electrical grid.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Durability tests of a five-centimeter diameter ion thruster system.

A modified Hughes SIT-5 system is being tested for durability at the Lewis Research Center. As of Oct. 1, 1972, the thruster subsystem has logged over 8000 hours of operation. The initial 2023 hours were run with a translating screen thrust vector grid. The thruster is currently operating with an electrostatic type vector grid. Profiles and maps taken at widely separated intervals show that performance and operating characteristics have remained essentially constant. Overall efficiency is about 32 per cent and power to thrust ratio is 170 watts per millipound at a specific impulse of 2500 seconds. Telescopic examination of the vector grid shows some sputtering erosion due to charge exchange and direct impingement ions. An independent test of the propellant storage and cathode-isolator-vaporizer subsystem has demonstrated good reliability under simulated thruster operating conditions.

Nakanishi, S.↗

Mars global surveyor

The design and performance of a highly reliable, 20 volt nickel hydrogen battery compatible with existing NiCad Mars observer based spacecraft components and an 800 psi, zirconium wall wick Common Pressure Vessel (CPV) are discussed. The objectives of the design process are: to meet or exceed all PD requirements by using existing technologies; to have high reliability hardware and parallel fabrication of components; and low schedule risk configurations. This paper discusses the tests performed on the batteries (capacity, charge retention, random vib., pyro shock, energy density, and packing factor) and the results of the tests. In addition to the design discussion, a brief introduction on Mars Global Surveyor (MGS) Satellite objectives (NASA's next interplanetary mission) is also presented.

Source record↗

Computational modeling of charge hopping dynamics along a disordered one-dimensional wire with energy gradients in quantum environments

This computational study investigates the effects of energy gradients on charge hopping dynamics along a one-dimensional chain of discrete sites coupled to quantum bath, which is modeled at the level of Pauli master equation (PME). This study also assesses the performance of different approximations for the hopping rates. Three different methods for solving the PME, a fourth order Runge–Kutta method, numerical diagonalization of the rate matrix followed by analytic propagation, and kinetic Monte Carlo simulation method, are tested and confirmed to produce virtually identical values of time dependent mean square displacement, diffusion constant, and mobility. Five different rate expressions, exact numerical evaluation of Fermi’s Golden Rule (FGR) rate, stationary phase interpolation (SPI) approximation, semiclassical approximation, classical Marcus rate, and Miller–Abrahams rate, are tested to help understand the effects of approximations in representing quantum environments in the presence of energy gradients. The results based on direct numerical evaluation of FGR rate exhibit transition from diffusive to non-diffusive behavior with the increase in the gradient and show that the charge transport in the quantum bath is more sensitive to the magnitude of the gradient and the disorder than in the classical bath. Among all the four approximations for the hopping rates, the SPI approximation is confirmed to work best overall. A comparison of two different methods to calculate the mobility identifies drift motion of the population distribution as the major source of non-diffusive behavior and provides more reliable information on the contribution of quantum bath.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Power Oak Ridge Converter (ORC) for Extreme Fast Charging Applications

This project report presents a novel power converter system called Oak Ridge Converter (ORC), a patented technology developed by the Oak Ridge National Laboratory (ORNL) for XFC wireless EV charging systems. ORC integrates the grid interface converter (also known as the active front-end rectifier with power factor correction) with the high-frequency inverter stage, promoting size and cost-effective charging technology with reduced infrastructure costs. The integration of the front-end rectifier with the high-frequency inverter truly eliminates one power conversion stage and achieves more than 33% size, weight, volume, and cost reduction on the wireless charging systems. Furthermore, ORC eliminates the primary side direct current (DC) bus bulk capacitors that are usually aluminum electrolytic capacitors and replaces them with very small, cost-effective, highly reliable, and high-temperature operation-capable alternate current (AC) film capacitors. ORC is also applicable to both single-phase and poly-phase couplers. When used with polyphase couplers, ORC further improves the power density of the overall system with higher power density power electronics. Moreover, ORC is inherently bidirectional and allows the system to provide power back to the grid for grid ancillary or grid support services. The ORC, based on a patented ORNL technology, is an excellent approach to resolving the high-power charging problems as described above, which directly converts the 60 hertz (Hz) line frequency into high frequency (i.e., 85 kilohertz (kHz)) to use with a high-frequency isolation transformer or wireless charging coils while eliminating the primary side number of power conversion stages from two to one. The result of the project is a prototype and reference design for a high-power wireless charging system—including power electronics, magnetics, and thermal—serving as a baseline for product development. The proposed system results are demonstrated for 270 kW of output power, with the system's overall efficiency of 92% from the AC grid, achieving less than 3% current total harmonic distortion (THD) and around 0.99 power factor (PF).

33 ADVANCED PROPULSION SYSTEMS↗

Ultralow-temperature cryogenic transmission electron microscopy using a new helium flow cryostat stage

Advances in cryogenic electron microscopy have opened new avenues for probing quantum phenomena in correlated materials. This study reports the installation and performance of a new side-entry condenZero cryogenic cooling system for JEOL (Scanning) Transmission Electron Microscopes (S/TEM), utilizing compressed liquid helium (LHe) and designed for imaging and spectroscopy at ultra-low temperatures. The system includes an external dewar mounted on a vibration-damping stage and a pressurized, low-noise helium transfer line with a remotely controllable needle valve, ensuring stable and efficient LHe flow with minimal thermal and mechanical noise. Performance evaluation demonstrates a stable base temperature of 4.37 K measured using a Cernox bare chip sensor on the holder with temperature fluctuations within ±0.004 K. Complementary in-situ electron energy-loss spectroscopy (EELS) via aluminum bulk plasmon analysis was used to measure the local specimen temperature and validate cryogenic operation during experiments. The integration of cryogenic cooling with other microscopy techniques, including electron diffraction and Lorentz TEM, was demonstrated by resolving charge density wave (CDW) transitions in NbSe2 using electron diffraction, and imaging nanometric magnetic skyrmions in MnSi via Lorentz TEM. In conclusion, this platform provides reliable cryogenic operation below 7 K, establishing a low-drift route for direct visualization of electronic and magnetic phase transformations in quantum materials.

Charge density wave↗

High-Entropy and Superstructure-Stabilized Layered Oxide Cathodes for Sodium-Ion Batteries

Layered transition metal oxides are appealing cathodes for sodium-ion batteries due to their overall advantages in energy density and cost. But their stabilities are usually compromised by the complicated phase transition and the oxygen redox, particularly when operating at high voltages, leading to poor structural stability and substantial capacity loss. Here, in this study, an integrated strategy combing the high-entropy design with the superlattice-stabilization to extend the cycle life and enhance the rate capability of layered cathodes is reported. It is shown that the as-prepared high-entropy Na 2/3 Li 1/6 Fe 1/6 Co 1/6 Ni 1/6 Mn 1/3 O 2 cathode enables a superlattice structure with Li/transition metal ordering and delivers excellent electrochemical performance that is not affected by the presence of phase transition and oxygen redox. It achieves a high reversible capacity (171.2 mAh g –1 at 0.1 C), a high energy density (531 Wh kg –1 ), extended cycling stability (89.3% capacity retention at 1 C for 90 cycles and 63.7% capacity retention at 5 C after 300 cycles), and excellent fast-charging capability (78 mAh g –1 at 10 C). This strategy would inspire more rational designs that can be leveraged to improve the reliability of layered cathodes for secondary-ion batteries.

25 ENERGY STORAGE↗

Utilizing the unique charge extraction properties of antimony tin oxide nanoparticles for efficient and stable organic photovoltaics

Simultaneously enhancing device performance and longevity, as well as balancing the requirements on cost, scalability, and simplification of processing, is the goal of interface engineering of organic solar cells (OSCs). In our work, we strategically introduce antimony (Sb 3+ ) cations into an efficient and generic n-type SnO 2 nanoparticles (NPs) host during the scalable flame spray pyrolysis synthesis. Accordingly, a significant switch of conduction property from an n-type character to a p-type character is observed, with a corresponding shift in the work function (WF) from 4.01 ± 0.02 eV for pristine SnO 2 NPs to 5.28 ± 0.02 eV for SnO 2 NPs with 20 mol. % Sb content (ATO). Both pristine SnO 2 and ATO NPs with fine-tuned optoelectronic properties exhibit remarkable charge carrier extraction properties, excellent UV resistance and photo-stability being compatible with various state-of-the-art OSCs systems. The reliable and scalable pristine SnO 2 and ATO NPs processed by doctor-blading in air demand no complex post-treatment. Our work offers a simple but unique approach to accelerate the development of advanced interfacial materials, which could circumvent the major existing interfacial problems in solution-processed OSCs.

14 SOLAR ENERGY↗

Mapping valence electron distributions with multipole density formalism using 4D-STEM

Recent advancement in aberration correction and detector technology opened a door to various applications using 4D-STEM, which yields a diffraction pattern for each scanning position within a crystal unit-cell in scanning transmission electron microscopy (STEM) and generates incredible amounts of data in momentum space. Currently 4D-STEM analysis relies on the center-of-mass of the diffraction patterns in electric field and charge density mapping. It only derives the total projected charge density and is limited to phase objects, e.g. extremely thin samples. Here, we propose a new analytical method to accurately map aspherical valence electron distributions with atom-centered multipolar functions formalism using the whole 4D-STEM dataset. We demonstrate that, with the full dynamical calculations for various sample thicknesses, the method is sensitive not only to the miniscule charge transfer, but also to the atomic site symmetry and aspherical electron orbitals. The process of the refinement is much more robust and reliable than quantitative convergent beam electron diffraction.

4D-STEM↗

Production of neutron-rich heavy nuclei in deep-inelastic 208 Pb + 208 Pb collisions within the stochastic mean-field theory

In deep-inelastic collisions of heavy nuclei, reaction products with a wide range of mass and charge are produced. Such collisions been considered as a possible way to produce superheavy nuclei, as an alternative to fusion reactions. To provide reliable theoretical predictions, it is desired to develop microscopic approaches that correctly and accurately describe nucleon transfer processes in dissipative collisions of heavy nuclei. The purpose of the present work is (1) to investigate the mechanism of nucleon transfers in dissipative collisions of two heavy nuclei, and (2) to explore possible pathways to produce neutron-rich heavy nuclei, through detailed theoretical analyses of fluctuations and correlations in nucleon transfers in 208 Pb + 208 Pb reactions. Three-dimensional time-dependent Hartree-Fock (TDHF) calculations are performed for the collisions of 208 Pb + 208 Pb at 𝐸 c.m. = 832, 936, and 1040 MeV, using the Skyrme SLy4d energy density functional. To calculate fluctuations and correlations in nucleon transfers, we employ the stochastic mean-field (SMF) theory, and the results are compared with another theoretical framework currently available, the time-dependent random phase approximation (TDRPA). Primary and secondary production cross sections are calculated with the SMF theory combined with a statistical model, GEMINI ++ . Using information of nucleon flow across a neck of colliding nuclei in TDHF calculations, we solve quantal diffusion equations for fluctuations and correlations in nucleon transfers based on the SMF theory. From the SMF calculations, we obtain the time evolution of diffusion coefficients as well as fluctuations and correlations in nucleon transfers for a range of initial orbital angular momenta. We compare the results of the SMF calculations with those of TDRPA, showing that TDRPA tends to predict substantially larger fluctuations and correlations in strongly damped collisions of heavy nuclei, which exhibit complex initial angular momentum dependence, while the SMF results provide almost constant (stable) values. Using the obtained fluctuations and correlations, we calculate primary and secondary production cross sections for the 208 Pb + 208 Pb collisions. From the results, we find that both lighter and heavier reaction products as compared to 208 Pb are produced for a wide region in the 𝑁−𝑍 plane as primary products, thanks to the quantal diffusion mechanism in the dissipative collisions. However, we show that cross sections for production of heavy nuclei with 𝑍 ≳ 90 or 𝑁 ≳ 135 are washed out due to secondary particle evaporation and/or fission processes. On the other hand, we find that there remain sizable cross sections for production of neutron-rich nuclei along 𝑁 = 126 with 𝑍< 82, even after secondary disintegration processes. We demonstrate that the secondary production cross sections depend weakly on incident energies, but lower (higher) energy is slightly preferred for production of nuclei with smaller (larger) atomic numbers as compared to 𝑍 = 82. Here, based on the microscopic SMF calculations, it has been shown that deep-inelastic collisions of heavy nuclei, such as 208 Pb + 208 Pb examined in this study, can be a promising means to produce neutron-rich heavy nuclei along 𝑁=126. Discrepancies between the SMF and TDRPA approaches are left unsolved for future investigations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Review of Current Research Trends in Power-Electronic Innovations in Cyber–Physical Systems

Here, in this article, a broad overview of the current research trends in power-electronic innovations in cyber–physical systems (CPSs) is presented. The recent advances in semiconductor device technologies, control architectures, and communication methodologies have enabled researchers to develop integrated smart CPSs that can cater to the emerging requirements of smart grids, renewable energy, electric vehicles, trains, ships, the Internet of Things (IoT), and so on. The topics presented in this article include novel power-distribution architectures, protection techniques considering large renewable integration in smart grids, wireless charging in electric vehicles, simultaneous power and information transmission, multihop network-based coordination, power technologies for renewable energy and smart transformer, CPS reliability, transactive smart railway grid, and real-time simulation of shipboard power systems. It is anticipated that the research trends presented in this article will provide a timely and useful overview to the power-electronics researchers with broad applications in CPSs.

24 POWER TRANSMISSION AND DISTRIBUTION↗

The electrical power subsystem of the Pioneer F/G spacecraft.

The Pioneer F/G spacecraft is the first to use radioisotope thermoelectric generators (RTG's) for a long duration interplanetary mission. This paper describes the design of the spacecraft power subsystem which meets the unique requirements of such a mission. The primary power source consists of four SNAP 19 RTG's. The 4.2 volt dc outputs of the RTG's are inverted to higher voltage ac by four inverters which are connected in parallel at their outputs. A power control unit (PCU) regulates the ac output of the inverters such that the RTG's are operated at near maximum power voltage throughout the mission. The PCU also contains charge and discharge controls for a silver cadmium battery which supplements the RTG's if load requirements temporarily exceed RTG power output. Battery reliability is enhanced by overcharge and cell reversal protection electronics which are provided for each cell. Multiple, low voltage, regulated dc outputs which supply power to the spacecraft subsystems are provided by a central transformer-rectifier-filter unit (CTRF). The CTRF operates directly from the regulated ac bus.

Reppucci, G. M.↗