Results for “Ceramic materials” — Page 17

NASA NTRS1996

Mullite fiber reinforced reaction bonded Si3N4 composites

Fracture toughnesses of brittle ceramic materials have been improved by introducing reinforcements and carefully tailored interface layers. Silicon carbide and Si3N4 have been emphasized as matrices of structural composites intended for high temperature service because they combine excellent mechanical, chemical, thermal and physical properties. Both matrices have been successfully toughened with SiC fibers, whiskers and particles for ceramic matrix composite (CMC) parts made by sintering, hot pressing or reaction forming processes. These SiC reinforced CMCs have exhibited significantly improved toughnesses at low and intermediate temperature levels, as well as retention of properties at high temperatures for selected exposures; however, they are vulnerable to attack from elevated temperature dry and wet oxidizing atmospheres after the matrix has cracked. Property degradation results from oxidation of interface layers and/or reinforcements. The problem is particularly acute for small diameter (-20 tim) polymer derived SiC fibers used for weavable toes. This research explored opportunities for reinforcing Si3N4 matrices with fibers having improved environmental stability; the findings should also be applicable to SiC matrix CMCs.

Saleh, T.↗

NASA NTRS2014

Method for Making a Fuel Cell from a Solid Oxide Monolithic Framework

The invention is a novel solid oxide fuel cell (SOFC) stack comprising individual bi-electrode supported fuel cells in which a thin electrolyte is supported between electrodes of essentially equal thickness. Individual cell units are made from graded pore ceramic tape that has been created by the freeze cast method followed by freeze drying. Each piece of graded pore tape later becomes a graded pore electrode scaffold that subsequent to sintering, is made into either an anode or a cathode by means of appropriate solution and thermal treatment means. Each cell unit is assembled by depositing of a thin coating of ion conducting ceramic material upon the side of each of two pieces of tape surface having the smallest pore openings, and then mating the coated surfaces to create an unsintered electrode scaffold pair sandwiching an electrolyte layer. The opposing major outer exposed surfaces of each cell unit is given a thin coating of electrically conductive ceramic, and multiple cell units are stacked, or built up by stacking of individual cell layers, to create an unsintered fuel cell stack. Ceramic or glass edge seals are installed to create flow channels for fuel and air. The cell stack with edge sealants is then sintered into a ceramic monolithic framework. Said solution and thermal treatments means convert the electrode scaffolds into anodes and cathodes. The thin layers of electrically conductive ceramic become the interconnects in the assembled stack.

Cable, Thomas L.↗

NASA NTRS1987

Characterization of ion beam modified ceramic wear surfaces using Auger electron spectroscopy

An investigation of the surface chemistry and morphology of the wear surfaces of ceramic material surfaces modified by ion beam mixing has been conducted using Auger electron spectroscopy and secondary electron microscopy. Studies have been conducted on ceramic/ceramic friction and wear couples made up of TiC and NiMo-bonded TiC cermet pins run against Si3N4 and partially stabilized zirconia disc surfaces modified by the ion beam mixing of titanium and nickel, as well as ummodified ceramic/ceramic couples in order to determine the types of surface changes leading to the improved friction and wear behavior of the surface modified ceramics in simulated diesel environments. The results of the surface analyses indicate that the formation of a lubricating oxide layer of titanium and nickel, is responsible for the improvement in ceramic friction and wear behavior. The beneficial effect of this oxide layer depends on several factors, including the adherence of the surface modified layer or subsequently formed oxide layer to the disc substrate, the substrate materials, the conditions of ion beam mixing, and the environmental conditions.

Wei, W.↗

NASA NTRSDate not supplied

The Use of Immersion Rigs for High Temperature Hydrogen Exposure Testing Within the Nuclear Thermal Rocket Element Environmental Simulator (NTREES): NTREES-5 Hydrogen Heat Exchanger (N5HHX-01)

The Nuclear Thermal Rocket Element Environmental Simulator (NTREES) facility at NASA’s Marshall Space Flight Center (MSFC) subjects materials and components typically found on nuclear thermal propulsion (NTP) systems to non-nuclear simulations of prototypic NTP reactor thermohydraulic environments. With 1.2 MW of inductive power available, the currently employed methods to simulate nuclear heating in NTREES consist of 1) inductively heating a test specimen, which typically cannot be performed on ceramic materials, or 2) heating gas that envelops the test specimen. The latter of these has provided a basis for developing so-called “immersion rigs” to be used in NTREES. Furthermore, immersion rigs are especially useful in the case of smaller, technically challenging test specimens. One such device, the “NTREES-5 Hydrogen Heat Exchanger” (N5HHX-01), designed and deployed to test small material coupons to ~0.5 g/s of 2800 K, 500 psi Hydrogen, is discussed herein. To achieve this desired delivery temperature level, the most suitable material for the N5HHX’s construction was pure tungsten, which imposed budgetary and manufacturing challenges. Also discussed in this paper is the design of the N5HHX rig’s sample container, which became the first iteration of improving NTREES small material coupon test operations by permitting rapid changeout of different material samples.

Reactor Testing↗

NASA NTRS1974

Design and evaluation of experimental ceramic automobile thermal reactors

The paper summarizes the results obtained in an exploratory evaluation of ceramics for automobile thermal reactors. Candidate ceramic materials were evaluated in several reactor designs using both engine dynamometer and vehicle road tests. Silicon carbide contained in a corrugated metal support structure exhibited the best performance, lasting 1100 hours in engine dynamometer tests and for more than 38,600 kilimeters (24,000 miles) in vehicle road tests. Although reactors containing glass-ceramic components did not perform as well as silicon carbide, the glass-ceramics still offer good potential for reactor use with improved reactor designs.

Stone, P. L.↗

NASA NTRS1974

Design and evaluation of experimental ceramic automobile thermal reactors

The results obtained in an exploratory evaluation of ceramics for automobile thermal reactors are summarized. Candidate ceramic materials were evaluated in several reactor designs by using both engine-dynamometer and vehicle road tests. Silicon carbide contained in a corrugated-metal support structure exhibited the best performance, lasting 1100 hr in engine-dynamometer tests and more than 38,600 km (24000 miles) in vehicle road tests. Although reactors containing glass-ceramic components did not perform as well as those containing silicon carbide, the glass-ceramics still offer good potential for reactor use with improved reactor designs.

Stone, P. L.↗

NASA NTRS2006

Improving Thermomechanical Properties of SiC/SiC Composites

Today, a major thrust toward improving the thermomechanical properties of engine components lies in the development of fiber-reinforced silicon carbide matrix composite materials, including SiC-fiber/SiC-matrix composites. These materials are lighter in weight and capable of withstanding higher temperatures, relative to state-of-the-art metallic alloys and oxide-matrix composites for which maximum use temperatures are in the vicinity of 1,100 C. In addition, the toughness or damage tolerance of the SiC-matrix composites is significantly greater than that of unreinforced silicon-based monolithic ceramics. For successful application in advanced engine systems, the SiC-matrix composites should be able to withstand component service stresses and temperatures for the desired component lifetimes. Inasmuch as the high-temperature structural lives of ceramic materials are typically limited by creep-induced growth of flaws, a key property required of such composite materials is high resistance to creep under conditions of use. Also, the thermal conductivity of the materials should be as high as possible so as to minimize component thermal gradients and thermal stresses. A state-of-the-art SiC-matrix composite is typically fabricated in a three-step process: (1) fabrication of a component-shaped architectural preform reinforced by thermally stable high-performance fibers, (2) chemical-vapor infiltration (CVI) of a fiber-coating material such as boron nitride (BN) into the preform, and (3) infiltration of an SiC-based matrix into the remaining porosity in the preform. Generally, the matrices of the highest-performing composites are fabricated by initial use of a CVI SiC matrix component that is typically more thermally stable and denser than matrix components formed by processes other than CVI. As such, the initial SiC matrix component made by CVI provides better environmental protection to the coated fibers embedded within it. Also, the denser CVI SiC imparts to the composite better resistance to propagation of cracks, enhanced thermal conductivity, and higher creep resistance.

DiCarlo, James A.↗

NASA NTRS1999

Temperature Measurement of a Miniature Ceramic Heater in the Presence of an Extended Interfering Background Radiation Source Using a Multiwavelength Pyrometer

Temperature measurement of small (millimeter size) objects is generally difficult and demanding. Measurement involving ceramic materials using the traditional one- and two-color pyrometer is difficult because of their complex optical properties, such as low emissivity which may vary with both temperature and wavelength. Pyrometry applications in an environment with an interfering radiation source of extended dimension adds extra complexity to the process. We show that the multiwavelength pyrometer successfully measured the temperatures of a millimeter (mm) size ceramic heater under these demanding conditions.

Ng, Daniel↗

NASA NTRS1974

Model for thermal stress resistance of truly elastic materials containing more than one crack

The model was developed upon the physical properties of surface energy and intrinsic modulus of elasticity of a material containing a number of equal sized microcracks which are independent of one another. The effect of these cracks upon the strain energy per unit volume of material necessary to continue simultaneous crack growth as well as the measured physical properties was established, and the thermal stress resistance is developed in terms of this energy. The model is expressed in its final form in terms of the measured physical properties of fracture strength, effective modulus of elasticity, and coefficient of thermal expansion. The model was applied to existent thermal stress data of ceramic materials for which these physical properties had been measured. On the basis of these data it was concluded that the thermal stress resistance of a material may be improved by increasing the fracture strength.

Lineback, L. D.↗

NASA NTRS1988

Development of sensors for ceramic components in advanced propulsion systems: Survey and evaluation of measurement techniques for temperature, strain and heat flux for ceramic components in advanced propulsion systems

The report presents the final results of Tasks 1 and 2, Development of Sensors for Ceramic Components in Advanced Propulsion Systems (NASA program NAS3-25141). During Task 1, an extensive survey was conducted of sensor concepts which have the potential for measuring surface temperature, strain and heat flux on ceramic components for advanced propulsion systems. Each sensor concept was analyzed and evaluated under Task 2; sensor concepts were then recommended for further development. For temperature measurement, both pyrometry and thermographic phosphors are recommended for measurements up to and beyond the melting point of ceramic materials. For lower temperature test programs, the thin-film techniques offer advantages in the installation of temperature sensors. Optical strain measurement techniques are recommended because they offer the possibility of being useful at very high temperature levels. Techniques for the measurement of heat flux are recommended for development based on both a surface mounted sensor and the measurement of the temperature differential across a portion of a ceramic component or metallic substrate.

Atkinson, W. H.↗

NASA NTRS2006

Development of a Thin Gauge Metallic Seal for Gas Turbine Engine Applications to 1700 F

The goal of doubling thrust-to-weight ratio for gas turbine engines has placed significant demands on engine component materials. Operating temperatures for static seals in the transition duct and turbine sections for instance, may well reach 2000 F within the next ten years. At these temperatures conventional age-hardenable superalloys lose their high strength via overaging and eventual dissolution of the gamma precipitate, and are well above their oxidation stability limit. Conventional solid-solution-strengthened alloys offer metallurgical stability, but suffer from rapid oxidation and little useful load bearing strength. Ceramic materials can theoretically be used at these temperatures, but manufacturing processes are in the developmental stages.

England, Raymond O.↗

NASA NTRS1991

Ceramic composites for rocket engine turbines

The use of ceramic materials in the hot section of the fuel turbopump of advanced reusable rocket engines promises increased performance and payload capability, improved component life and economics, and greater design flexibility. Severe thermal transients present during operation of the Space Shuttle Main Engine (SSME), push metallic components to the limit of their capabilities. Future engine requirements might be even more severe. In phase one of this two-phase program, performance benefits were quantified and continuous fiber reinforced ceramic matrix composite components demonstrated a potential to survive the hostile environment of an advanced rocket engine turbopump.

Herbell, Thomas P.↗

NASA NTRS1991

Ceramic composites for rocket engine turbines

The use of ceramic materials in the hot section of the fuel turbopump of advanced reusable rocket engines promises increased performance and payload capability, improved component life and economics, and greater design flexibility. Severe thermal transients present during operation of the Space Shuttle Main Engine (SSME), push metallic components to the limit of their capabilities. Future engine requirements might be even more severe. In phase one of this two-phase program, performance benefits were quantified and continuous fiber reinforced ceramic matrix composite components demonstrated a potential to survive the hostile environment of an advaced rocket engine turbopump.

Herbell, Thomas P.↗

NASA NTRSDate not supplied

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRS2009

In-Situ Measurement of Hall Thruster Erosion Using a Fiber Optic Regression Probe

One potential life-limiting mechanism in a Hall thruster is the erosion of the ceramic material comprising the discharge channel. This is especially true for missions that require long thrusting periods and can be problematic for lifetime qualification, especially when attempting to qualify a thruster by analysis rather than a test lasting the full duration of the mission. In addition to lifetime, several analytical and numerical models include electrode erosion as a mechanism contributing to enhanced transport properties. However, there is still a great deal of dispute over the importance of erosion to transport in Hall thrusters. The capability to perform an in-situ measurement of discharge channel erosion is useful in addressing both the lifetime and transport concerns. An in-situ measurement would allow for real-time data regarding the erosion rates at different operating points, providing a quick method for empirically anchoring any analysis geared towards lifetime qualification. Erosion rate data over a thruster s operating envelope would also be useful in the modeling of the detailed physics inside the discharge chamber. There are many different sensors and techniques that have been employed to quantify discharge channel erosion in Hall thrusters. Snapshots of the wear pattern can be obtained at regular shutdown intervals using laser profilometry. Many non-intrusive techniques of varying complexity and sensitivity have been employed to detect the time-varying presence of erosion products in the thruster plume. These include the use quartz crystal microbalances, emission spectroscopy, laser induced flourescence, and cavity ring-down spectroscopy. While these techniques can provide a very accurate picture of the level of eroded material in the thruster plume, it is more difficult to use them to determine the location from which the material was eroded. Furthermore, none of the methods cited provide a true in-situ measure of erosion at the channel surface while the thruster is in operation (i.e. none yield a continuous channel erosion measurement). A recent fundamental sensor development effort has led to a novel regression, erosion, and ablation sensor technology (REAST). The REAST sensor allows for measurement of real-time surface erosion rates at a discrete surface location. The sensor was tested using a linear Hall thruster geometry (see Fig. 1), which served as a means of producing plasma erosion of a ceramic discharge chamber. The mass flow rate, discharge voltage, and applied magnetic field strength could be varied, allowing for erosion measurements over a broad thruster operating envelope. Results are presented demonstrating the ability of the REAST sensor to capture not only the insulator erosion rates but also changes in these rates as a function of the discharge parameters.

Polzin, Kurt↗

NASA NTRS1972

Rolling-element fatigue life of silicon nitride balls: Preliminary test results

Hot pressed silicon nitride was evaluated as a rolling element bearing material. The five-ball fatigue tester was used to test 12.7 mm (0.500 in.) diameter balls at a maximum Hertz stress of 800,000 psi at a race temperature of 130 F. The fatigue spalls in the silicon nitride resembled those in typical bearing steels. The ten-percent fatigue life of the silicon nitride balls was approximately one-eighth to one-fifth that of typical bearing steels (52100 and M-50). The load capacity of the silicon nitride was approximately one-third that of typical bearing steels. The load capacity of the silicon nitride was significantly higher than previously tested ceramic materials for rolling element bearings.

Parker, R. J.↗