Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSORS - EFFICIENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

An analysis of the rotor blade stresses of the three stage compressor of the Ames Research Center 11- by 11-foot transonic wind tunnel

The static and dynamic rotor blade stresses of the three stage compressor were measured. Data are presented in terms of total blade stress for the complete operational range of compressor speeds and tunnel total pressures. Modal frequencies and variations with tunnel conditions were measured. Phase angles and coherences between various gage combinations are also presented. Recommendations for improvements are given for future rotor blade experimental investigations.

Dods, J. B., Jr.↗
NASA NTRS1978

End-wall boundary layer prediction for axial compressors

An integral boundary layer procedure was developed for the computation of viscous and secondary flows along the annulus walls of an axial compressor. The procedure is an outgrowth and extension of the pitch-averaged methods of Mellor and Horlock. In the present work secondary flow theory is used to develop approximations for the velocity profiles inside a rotating blade row and for the blade force deficit terms in the momentum integral equations. The computer code based on this procedure was iteratively coupled to a quasi-one-dimensional model for the external inviscid flow. Computed results are compared with measurements in a compressor cascade.

Sockol, P. M.↗
NASA NTRS1978

A study of axial compressor blade optimization for operation in the low Reynolds number regime

Original and previously published experimental data is presented in this study of axial compressor blade optimization for use in the subcritical Reynolds number region. Three methods of increasing cascade performance at these low Rc are presented, discussed, and compared: (1) use of sharp-leading-edge profiles, (2) trip wires or roughness elements, and (3) high free-stream turbulence. The original data was collected in the VKI C-1 cascade wind tunnel; during these tests blade chord Reynolds number was varied from 250,000 down to about 17,000. Each technique demonstrated an increase in low Reynolds number (based on chord) performance for certain profiles, with the sharp-leading-edge profile as the potential optimum. Axial compressors or pumps that must operate for a significant amount of their design life under low Reynolds number conditions might benefit substantially from these methods.

Roberts, W. B.↗
NASA NTRS1978

End-wall boundary layer prediction for axial compressors

An integral boundary layer procedure has been developed for the computation of viscous and secondary flows along the annulus walls of an axial compressor. The procedure is an outgrowth and extension of the pitch-averaged methods of Mellor and Horlock. In the present work secondary flow theory is used to develop approximations for the velocity profiles inside a rotating blade row and for the blade force deficit terms in the momentum integral equations. The computer code based on this procedure has been iteratively coupled to a quasi-one-dimensional model for the external inviscid flow. Computed results are compared with measurements in a compressor cascade.

Sockol, P. M.↗
NASA NTRS1979

Experimental evaluation of the effect of inlet distortion on compressor blade vibrations

Compressor rotor strain gage data from an engine test conducted with an inlet screen distortion were reduced and analyzed. These data are compared to data obtained from the same engine without inlet pressure distortion to determine the net effect of the distortion on the vibratory response of the compressor blades. The results obtained are presented.

Lubomski, J. F.↗
NASA NTRS1979

Effects of diffusion factor, aspect ratio and solidity on overall performance of 14 compressor middle stages

A series of high hub tip radius ratio compressor stages representative of the middle and latter stages of axial flow compressors is discussed. The effects of aspect ratio, diffusion factor, and solidity on rotor and stage performance are determined. Fourteen middle stages are tested to study the effects on performance of varying both diffusion through the rotor and stator blades and blade aspect ratio. The design parameters in the streamline analysis program, the blade geometry program, and the blade coordinate program are presented.

Britsch, W. R.↗
NASA NTRS1979

Turbulence characteristics in the near wake of a compressor rotor blade

This paper is concerned with the turbulence properties in the near wake of a rotating compressor blade. The variation of the axial, tangential and radial intensities as well as stresses across the wake and its decay characteristics were measured with a triaxial hot wire probe rotating with the rotor downstream of an axial flow compressor. The turbulence intensities decay very rapidly in the near wake region. The radial component of intensity is found to be higher than the tangential and axial components. This is a consequence of the effect of rotation on the turbulence structure. A qualitative analysis is carried out to predict the effect of rotation on the turbulence structure. These are in general agreement with the measured data.

Lakshminarayana, B.↗
NASA NTRS1979

Mean velocity and decay characteristics of the guidevane and stator blade wake of an axial flow compressor

Pure tone noise, blade row vibrations, and aerodynamic losses are phenomena which are influenced by stator and IGV (inlet guide vane) blade wake production, decay, and interaction in an axial-flow compressor. The objective of this investigation is to develop a better understanding of the nature of stator and IGV blade wakes that are influenced by the presence of centrifugal forces due to flow curvature. A single sensor hot wire probe was employed to determine the three mean velocity components of stator and IGV wakes of a single stage compressor. These wake profiles indicated a varying decay rate of the tangential and axial wake velocity components and a wake profile similarity. An analysis, which predicts this trend, has been developed. The radial velocities are found to be appreciable in both IGV and the stator wakes.

Lakshminarayana, B.↗
NASA NTRS1979

Experimental study of low aspect ratio compressor blading

The effects of low aspect ratio blading on aerodynamic performance were examined. Four individual transonic compressor stages, representative of the inlet stage of an advanced high pressure ratio core compressor, are discussed. The flow phenomena for the four stages are investigated. Comparisons of blade element parameters are presented for the two different aspect ratio configurations. Blade loading levels are compared for the near stall conditions and comparisons are made of loss and diffusion factors over the operating range of incidence angles.

Reid, L.↗
NASA NTRS1980

Asynchronous vibration problem of centrifugal compressor

An unstable asynchronous vibration problem in a high pressure centrifugal compressor and the remedial actions against it are described. Asynchronous vibration of the compressor took place when the discharge pressure (Pd) was increased, after the rotor was already at full speed. The typical spectral data of the shaft vibration indicate that as the pressure Pd increases, pre-unstable vibration appears and becomes larger, and large unstable asynchronous vibration occurs suddenly (Pd = 5.49MPa). A computer program was used which calculated the logarithmic decrement and the damped natural frequency of the rotor bearing systems. The analysis of the log-decrement is concluded to be effective in preventing unstable vibration in both the design stage and remedial actions.

Fujikawa, T.↗
NASA NTRS1980

Preliminary measurements of aerodynamic damping of a transonic compressor rotor

The aeroelastic behavior of a transonic compressor rotor operated in the MIT Blowdown Compressor Facility has been examined by means of piezoelectric motion sensors at the base of each of the 23 blades. Excitation has been observed due to rotating stall, due to an incipient flutter, and due to the facility startup transient. A method has been found for determining the aerodynamic damping force by modal analysis of the blade motion. Application of this technique to the example of excitation by rotating stall has led to the conclusions that the blade loading decreases in the stall cell, and that the damping force on the blades in the clean flow is in phase with blade velocity but opposite it in sign, leading to a logarithmic decrement of 0.2. This method of force derivation has quite general applicability as it requires only blade motion data such as are routinely acquired with strain gages. It is argued that models are needed for aerodynamic damping which focus on the effects of near neighbors of a given blade, since flutter often results in large response of isolated blades or small groups of blades.

Crawley, E. F.↗
NASA NTRS1981

CF6 High Pressure Compressor and Turbine Clearance Evaluations

In the CF6 Jet Engine Diagnostics Program the causes of performance degradation were determined for each component of revenue service engines. It was found that a significant contribution to performance degradation was caused by increased airfoil tip radial clearances in the high pressure compressor and turbine areas. Since the influence of these clearances on engine performance and fuel consumption is significant, it is important to accurately establish these relatonships. It is equally important to understand the causes of clearance deterioration so that they can be reduced or eliminated. The results of factory engine tests run to enhance the understanding of the high pressure compressor and turbine clearance effects on performance are described. The causes of clearance deterioration are indicated and potential improvements in clearance control are discussed.

Radomski, M. A.↗
NASA NTRS1981

Improving turbine engine compressor performance retention through airfoil coatings

In order to evaluate the potential effectiveness of coatings in limiting erosive damage to compressor airfoils, an effort was initiated to evaluate candidate coatings for substrate alloys typically used in commercial engine high compressor blades. Laboratory and rig erosion testing of plasma deposited and diffusion coatings described in this paper have shown the potential of a two to four fold improvement in erosion life. The selective application of these coatings to approximately the outer third of the airfoil avoids coating the fatigue critical region of the blade, thus providing erosion resistance potentially without compromising the fatigue strength of the blade. Both the plasma and the diffusion coatings also offer the advantage of low initial cost and a multi-source production base.

Friedrich, L. A.↗
NASA NTRS1980

Comparison of experimental and computational shock structure in a transonic compressor rotor

Measurement of passage shock strength in a transonic compressor rotor using a gas fluorescent technique revealed an unexpected variation in shock strength in the radial direction. An axisymmetric idealization would normally predict that the passage shock strength would gradually weaken when moving radially inward until disappearing at the sonic radius. However, the measurements indicated a sharp peak in strength at the nominal sonic radius. Blade boundary layer separation originating at this point accounts for about one half of the total rotor losses. A numerical computation of the three-dimensional inviscid flow, using time-marching techniques, has accurately predicted in general the radial and tangential variations in passage shock strength and in particular the sharp pressure peak at the nominal sonic radius. The overall shock strength was somewhat overpredicted, but this overprediction may be the result of boundary layer separation in the experiment. This paper presents comparisons between the optical density measurements and computational results and in addition a short analytical discussion which demonstrates that the sharp shock strength rise may occur in many transonic compressor rotors.

Haymann-Haber, G.↗
NASA NTRS1981

A simple model for compressor stall cell propagation

A simple model for full-span stall cells in axial compressors has been formulated. The sudden changes in velocity across blade rows as the blade passages enter and leave the stall are shown to have important dynamical consequences for the stall flow field. The one empirical constant needed in the analysis is determined using the data of Day (1976, 1978). From this, reasonable predictions of stall cell speed and trends in speed have been obtained for a number of different compressors. From the satisfactory comparison between predicted and measured stall cell speeds, it is tentatively concluded that the model contains the essentials of a correct description of the controlling mechanism of full-span rotating stall.

Cumpsty, N. A.↗
NASA NTRS1982

STGSTK: A computer code for predicting multistage axial flow compressor performance by a meanline stage stacking method

A FORTRAN computer code is presented for off-design performance prediction of axial-flow compressors. Stage and compressor performance is obtained by a stage-stacking method that uses representative velocity diagrams at rotor inlet and outlet meanline radii. The code has options for: (1) direct user input or calculation of nondimensional stage characteristics; (2) adjustment of stage characteristics for off-design speed and blade setting angle; (3) adjustment of rotor deviation angle for off-design conditions; and (4) SI or U.S. customary units. Correlations from experimental data are used to model real flow conditions. Calculations are compared with experimental data.

Steinke, R. J.↗
NASA NTRS1982

A FORTRAN program for calculating three dimensional, inviscid and rotational flows with shock waves in axial compressor blade rows: User's manual

A FORTRAN-IV computer program was developed for the calculation of the inviscid transonic/supersonic flow field in a fully three dimensional blade passage of an axial compressor rotor or stator. Rotors may have dampers (part span shrouds). MacCormack's explicit time marching method is used to solve the unsteady Euler equations on a finite difference mesh. This technique captures shocks and smears them over several grid points. Input quantities are blade row geometry, operating conditions and thermodynamic quanities. Output quantities are three velocity components, density and internal energy at each mesh point. Other flow quanities are calculated from these variables. A short graphics package is included with the code, and may be used to display the finite difference grid, blade geometry and static pressure contour plots on blade to blade calculation surfaces or blade suction and pressure surfaces. The flow in a low aspect ratio transonic compressor was analyzed and compared with high response total pressure probe measurements and gas fluorescence static density measurements made in the MIT blowdown wind tunnel. These comparisons show that the computed flow fields accurately model the measured shock wave locations and overall aerodynamic performance.

Thompkins, W. T., Jr.↗
NASA NTRS1982

Three-dimensional flow field in the tip region of a compressor rotor passage. II - Turbulence properties

The turbulence properties in the annulus wall region of an axial flow compressor rotor was measured using a triaxial, hot-wire probe rotating with the rotor. The flow was surveyed across the entire passage at five axial locations (leading edge, 1/4 chord, 1/2 chord, 3/4 chord, and the trailing edge location) and at six radial locations in a low-speed compressor rotor. The data derived include all three components of turbulence intensity and three components of turbulence stress. A comprehensive interpretation of the data with emphasis on features related to rotation, leakage flow, annulus wall boundary layer, and blade boundary layer interactions is included. All the components of turbulent intensities and stresses are found to be high in the leakage-flow mixing region. The radial component of intensities and stresses is found to be much higher than the corresponding streamwise components. The turbulent spectra clearly reveal the decay process of the inlet-guide-vane wake within the rotor passage.

Lakshminarayana, B.↗