Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “C++ analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Optical 14 C Tracing for Biological and Pharmaceutical Applications Using Two-Color Cavity Ringdown Spectroscopy

Laser-based 14 C quantitation has been proposed as a more affordable, higher-throughput, table-top alternative to accelerator mass spectrometry (AMS). Here, we demonstrate the feasibility of a mid-IR 14 C detector based on two-color cavity ringdown spectroscopy (2C-CRDS) for low-level 14 C isotope tracing in biological studies. The 2C-CRDS technique quantifies the sample 14 C content by measuring the 14 CO 2 absorption signals from the combusted samples with mid-IR lasers. With 2C-CRDS, we previously demonstrated the most sensitive and accurate optical measurements of 14 CO 2 . The current detection sensitivity and quantitation accuracy of the instrument, at a few parts per quadrillion (where a quadrillion = 10 15 ) 14 C/C mole fraction, is competitive against AMS. Here, by applying the 2C-CRDS 14 C sensor to two applications relevant to 14 C-labeled biochemical analysis and pharmaceutical studies, we demonstrate sub-fCi level (where 1 fCi = 10 –15 Ci) quantitation of sample 14 C activity, with a minimum sample-size requirement of 3 mg of carbon. The current measurement throughput, ~25 min/sample, is largely limited by the sampling efficiency of the online combustion and CO 2 processing interface to the 2C-CRDS instrument. The possibility of a significantly improved measurement throughput of a few minutes per sample is suggested by the results of a flow-through 14 CO 2 sampling scheme. In conclusion, this improved measurement efficiency, combined with the relatively low cost and compact size of a 2C-CRDS sensor, could potentially revolutionize high-sensitivity 14 C tracing in biological, pharmaceutical, and clinical studies.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Local structure effects of carbon-doping on the phase change material Ge 2 Sb 2 Te 5

Ge 2 Sb 2 Te 5 is used in phase change memory, a nonvolatile memory technology, due to its phase change properties. The primary advantage of phase change memory over the state-of-the-art (flash memory) is its simple and small device geometry, which allows for denser nodes and lower power consumption. In phase change memory, resistive heating induces fast switching between the high resistance amorphous and low resistance crystalline phases, corresponding to storage of low and high digital states, respectively. However, the instability of the amorphous phase of Ge 2 Sb 2 Te 5 presents issues with processing and long-term data storage; such issues can be resolved by C doping, which stabilizes the amorphous phase and raises the crystallization temperature. To better understand the local structural effects of C doping on Ge 2 Sb 2 Te 5 , in situ Ge K-edge X-ray absorption spectroscopy measurements were taken during heating of films with various C doping concentrations. Here, the range of structural transformation temperatures derived from X-ray absorption near-edge structure analysis across the C doping series proved narrower than crystallization temperatures reported in similar in situ X-ray diffraction experiments, which may reflect changes in local structure that precede long-range ordering during crystallization. In addition, rigorous extended X-ray absorption fine structure fitting across and between temperature series revealed effects of C doping on the rigidity of Ge–Te bonds at low (2 at% and 4 at%) C concentrations.

Langhout, John D.↗
NASA NTRS1991

Oxidation characteristics of Ti-33Al-6Nb-1.4Ta

Static oxidation kinetics of the gamma titanium-aluminide alloy Ti-33Al-6Nb-1.4Ta (wt pct) have been investigated in air from 700 to 1000 C and in oxygen from 800 to 1000 C using thermogravimetric analysis. The oxidation kinetics were controlled by the presence of alumina for all oxygen exposures and in air below 800 C, while the kinetics in air above 800 C were more complex. Oxidation products were identified using X-ray diffraction techniques. Oxide scale morphology was examined by SEM and TEM of the surfaces and across sections of oxidized specimens. The oxidation products formed depended on the exposure: Al2O3 and TiO2 were identified on all specimens exposed in and air and oxygen; the nitride phases TiN and Ti2AlN were also found on specimens exposed in air.

Wallace, T. A.↗
DOE OSTI2022

Microbe-iron interactions control lignin decomposition in soil

Lignin decomposition is critically linked to terrestrial carbon (C) cycle due to the enormous C mass of lignin and its importance in controlling overall rates of litter decomposition. Interactions between lignin and iron (Fe) minerals have been increasingly recognized as key mediators of lignin decomposition in experimental studies. However, we still lack a quantitative understanding of how Fe minerals interact with microbes to control lignin decomposition. Here, we leveraged experimental results from an incubation of Fe-rich soil, in which lignin decomposition rates were measured at aerobic conditions after four levels of pre-treated O2 availability, to examine microbe-Fe (MiFe) interactions in lignin decomposition with a MiFe model. We quantified how Fe redox cycling interacted with microbial activities to control lignin decomposition via data-model integration. Our results showed that the MiFe model with time-dependent growth and mortality functions better represented CO2 release from lignin decomposition (R2 ranging from 0.96 to 0.97) than models assuming either first-order or Michaelis-Menten kinetics. Reduction of Fe(III) to Fe(II) after pre-treatments with lower O2 availability stimu-lated the Fenton reaction to break down macro-molecular lignin into small molecules available to microbes. The small molecules of lignin and necromass bounded with oxidized Fe and were protected from decomposition. After 1-year incubation, the model implied that most of C stabilized with Fe minerals was derived from small molecular lignin C. Our quantitative analysis of microbe-Fe interactions sheds new light on lignin decomposition and preservation and helps improve model prediction of soil C persistence under global change.

Liao, Cuijuan↗
DOE OSTI2022

The Future of High Energy Physics Software and Computing (V2.1)

Software and Computing (S&C) are essential to all High Energy Physics (HEP) experiments and many theoretical studies. The size and complexity of S&C are now commensurate with that of experimental instruments, playing a critical role in experimental design, data acquisition/instrumental control, reconstruction, and analysis. Furthermore, S&C often plays a leading role in driving the precision of theoretical calculations and simulations. Within this central role in HEP, S&C has been immensely successful over the last decade. This report looks forward to the next decade and beyond, in the context of the 2021 Particle Physics Community Planning Exercise ("Snowmass") organized by the Division of Particles and Fields (DPF) of the American Physical Society.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Homogenization of Dendritic Structures and the High-Temperature Strength of the Refractory High-Entropy Alloy MoNbTaVW

MoNbTaVW, a pioneering refractory high-entropy alloy (RHEA), is renowned for its exceptional strength at elevated temperatures. Like most RHEAs, it solidifies into a dendritic microstructure with steep concentration gradients, necessitating heat treatment for equilibration. Steep concentration gradients typically complicate mechanical property analysis and modeling, key challenges for high-throughput alloy discovery. This study examines the effects of high-temperature homogenization (1800 °C for 8 hours) on the microstructure and mechanical properties of MoNbTaVW across temperatures up to 1200 °C. Postmortem microstructural analysis, coupled with chemical, crystallographic, and mechanical assessments, revealed that yield strength was surprisingly insensitive to homogenization, with less than a 3 pct difference between as-cast and heat-treated materials. Nanoindentation confirmed minimal nanohardness changes across the dendritic structure at room temperature. However, homogenization significantly enhanced high-temperature work hardening, producing higher peak compressive strength. Both as-cast and homogenized MoNbTaVW exhibited room-temperature strengths of 1400 MPa, exceeding previously reported values. These findings demonstrate that high-temperature treatment enables microstructural homogenization without compromising strength, a unique behavior among RHEAs. In conclusion, while not universally applicable, this insight highlights the importance of understanding microstructural development in experimental alloys and offers a pathway to design alloys that achieve homogeneous-like properties without heat treatment.

Rietema, C. J. [Lawrence Livermore National Labora↗
DOE OSTI2022

Partial wave analysis of the charmed baryon hadronic decay $ {\Lambda}_c^{+} $ → Λ π +π 0

Based on e + e - collision samples corresponding to an integrated luminosity of 4.4 fb -1 collected with the BESIII detector at center-of-mass energies between 4.6 GeV and 4.7 GeV, a partial wave analysis of the charmed baryon hadronic decay ${\Lambda}_c^{+}$ → Λπ + π 0 is performed, and the decays ${\Lambda}_c^{+}$ → Λρ(770) + and ${\Lambda}_c^{+}$ → Σ(1385)π are studied for the first time. Making use of the world-average branching fraction $\mathcal{B}$ (${\Lambda}_c^{+}$ → Λπ + π 0 ), their branching fractions are determined to be $\mathcal{B}$(${\Lambda}_c^{+}$ → Λρ(770) + ) = (4.06 ± 0.30 ± 0.35 ± 0.23) x 10 -2 , $\mathcal{B}$(${\Lambda}_c^{+}$ → Σ(1385) + )π 0 ) = (5.86 ± 0.49 ± 0.52 ± 0.35) x 10 -3 , $\mathcal{B}$(${\Lambda}_c^{+}$ → Σ(1385) 0 )π + ) = (6.47 ± 0.59 ± 0.66 ± 0.38) x 10 -3 , where the first uncertainties are statistical, the second are systematic, and the third are from the uncertainties of the branching fractions $\mathcal{B}$ ${\Lambda}_c^{+}$ → Λπ + π 0 and $\mathcal{B}$(Σ(1385) → Λπ). In addition, the decay asymmetry parameters are measured to be αΛρ(770)+ = - 0.763 ± 0.053 ± 0.045, $\alpha$ Σ(1385)+π 0 = -0.917 ± 0.069 ± 0.056, and $\alpha$ Σ(1385) 0 π + = -0.789 ± 0.098 ± 0.056.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1964

Some characteristics of black spherules.

Black spherules from Greenland ice sheets compared to industrial weld-spatter spherules, using density measurements coupled with chemical analysis

EXTRATERRESTRIAL MATTER↗
NASA NTRS1972

Entry trajectory, entry environment, and analysis of spacecraft motion for the RAM C-3 flight experiment

The RAM C-3 flight experiment was launched to study the problem of radiofrequency blackout at an entry velocity of 24,300 ft/sec. The flight is described, and data for the entry trajectory and environment, which include the effects of actual temperature measured the day of launch, are presented. An analysis of entry spacecraft motions was performed. This analysis included the determination of wind angles from measured accelerations and estimates of wind angles at high altitudes from gyro-measured rotation rates. The maximum wind angles were found to be less than 5 deg to the point of pitch-roll resonance where the total wind angle increased to 8.5 deg and the roll rate started decreasing. A plausible cause for the decrease in roll rate was shown to be a combination of trim angle and an offset center of gravity.

RAM↗
NASA NTRS1995

Structural characterization and regulatory element analysis of the heart isoform of cytochrome c oxidase VIa

In order to investigate the mechanism(s) governing the striated muscle-specific expression of cytochrome c oxidase VIaH we have characterized the murine gene and analyzed its transcriptional regulatory elements in skeletal myogenic cell lines. The gene is single copy, spans 689 base pairs (bp), and is comprised of three exons. The 5'-ends of transcripts from the gene are heterogeneous, but the most abundant transcript includes a 5'-untranslated region of 30 nucleotides. When fused to the luciferase reporter gene, the 3.5-kilobase 5'-flanking region of the gene directed the expression of the heterologous protein selectively in differentiated Sol8 cells and transgenic mice, recapitulating the pattern of expression of the endogenous gene. Deletion analysis identified a 300-bp fragment sufficient to direct the myotube-specific expression of luciferase in Sol8 cells. The region lacks an apparent TATA element, and sequence motifs predicted to bind NRF-1, NRF-2, ox-box, or PPAR factors known to regulate other nuclear genes encoding mitochondrial proteins are not evident. Mutational analysis, however, identified two cis-elements necessary for the high level expression of the reporter protein: a MEF2 consensus element at -90 to -81 bp and an E-box element at -147 to -142 bp. Additional E-box motifs at closely located positions were mutated without loss of transcriptional activity. The dependence of transcriptional activation of cytochrome c oxidase VIaH on cis-elements similar to those found in contractile protein genes suggests that the striated muscle-specific expression is coregulated by mechanisms that control the lineage-specific expression of several contractile and cytosolic proteins.

Non-NASA Center↗
DOE OSTI2023

Radiocarbon analysis of soil microbial biomass via direct chloroform extraction

Microbial processing of soil organic matter is a significant driver of C cycling, yet we lack an understanding of what shapes the turnover of this large terrestrial pool. In part, this is due to limited options for accurately identifying the source of C assimilated by microbial communities. Laboratory incubations are the most common method for this; however, they can introduce artifacts due to sample disruption and processing and can take months to produce sufficient CO 2 for analysis. We present a biomass extraction method which allows for the direct 14 C analysis of microbial biomolecules and compare the results to laboratory incubations. In the upper 50 cm soil depths, the Δ 14 C from incubations was indistinguishable from that of extracted microbial biomass. Below 50 cm, the Δ 14 C of the biomass was more depleted than that of the incubations, either due to the stimulation of labile C decomposition in the incubations, the inclusion of biomolecules from non-living cells in the biomass extractions, or differences in C used for assimilation versus respiration. Our results suggest that measurement of Δ 14 C of microbial biomass extracts can be a useful alternative to soil incubations.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2002

Design and Study of a LOX/GH2 Throttleable Swirl Injector for Rocket Applications

A LOX/GH2 swirl injector was designed for a 10:1 propellant throttling range. To accomplish this, a dual LOX manifold was used feeding a single common vortex chamber of the swirl element. Hot-fire experiments were conducted for rocket chamber pressures from 80 to 800 psia at a mixture ratio of nominally 6.0 using steady flow, single-point-per-firing cases as well as dynamic throttling conditions. Low frequency (mean) and high frequency (fluctuating) pressure transducer data, flow meter measurements, and Raman spectroscopy images for mixing information were obtained. The injector design, experimental setup, low frequency pressure data, and injector performance analysis are presented. C* efficiency was very high (approx. 100%) at the middle of the throttleable range with somewhat lower performance at the high and low ends. From the analysis of discreet steady state operating conditions, injector pressure drop was slightly higher than predicted with an inviscid analysis, but otherwise agreed well across the design throttling range. Dynamic throttling of this injector was attempted with marginal success due to the immaturity of the throttling control system. Although the targeted mixture ratio of 6.0 was not maintained throughout the dynamic throttling profile, the injector behaved well over the wide range of conditions.

Greene, Christopher↗
NASA NTRS2011

Sol-Gel Synthesis of La(0.6)Sr(0.4)CoO(3-x) and Sm(0.5)Sr(0.5)CoO(3-x) Cathode Nanopowders for Solid Oxide Fuel Cells

Nanopowders of La(0.6)Sr(0.4)CoO(3-x) (LSC) and Sm(0.5)Sr(0.5)CoO(3-x) (SSC) compositions, which are being investigated as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC) with La(Sr)Ga(Mg)O(3-x) (LSGM) as the electrolyte, were synthesized by low-temperature sol-gel method using metal nitrates and citric acid. Thermal decomposition of the citrate gels was followed by simultaneous DSC/TGA methods. Development of phases in the gels, on heat treatments at various temperatures, was monitored by x-ray diffraction. Solgel powders calcined at 550 to 1000 C consisted of a number of phases. Single perovskite phase La(0.6)Sr(0.4)CoO(3-x) or Sm(0.5)Sr(0.5)CoO(3-x) powders were obtained at 1200 and 1300 C, respectively. Morphological analysis of the powders calcined at various temperatures was done by scanning electron microscopy. The average particle size of the powders was approx.15 nm after 700 C calcinations and slowly increased to 70 to 100 nm after heat treatments at 1300 to 1400 C.

Bansal, Narottam P.↗
DOE OSTI2024

Risk-Aware Framework Development for Disruption Prediction: Alcator C-Mod and DIII-D Survival Analysis

Abstract Survival regression models can achieve longer warning times at similar receiver operating characteristic performance than previously investigated models. Survival regression models are also shown to predict the time until a disruption will occur with lower error than other predictors. Time-to-event predictions from time-series data can be obtained with a survival analysis statistical framework, and there have been many tools developed for this task which we aim to apply to disruption prediction. Using the open-source Auton-Survival package we have implemented disruption predictors with the survival regression models Cox Proportional Hazards, Deep Cox Proportional Hazards, and Deep Survival Machines. To compare with previous work, we also include predictors using a Random Forest binary classifier, and a conditional Kaplan-Meier formalism. We benchmarked the performance of these five predictors using experimental data from the Alcator C-Mod and DIII-D tokamaks by simulating alarms on each individual shot. We find that developing machine-relevant metrics to evaluate models is an important area for future work. While this study finds cases where disruptive conditions are not predicted, there are instances where the desired outcome is produced. Giving the plasma control system the expected time-to-disruption will allow it to determine the optimal actuator response in real time to minimize risk of damage to the device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2012

Carbon and Hydrogen Isotope Measurements of Alcohols and Organic Acids by Online Pyroprobe-GC-IRMS

The detection of methane in the atmosphere of Mars, combined with evidence showing widespread water-rock interaction during martian history, suggests that the production of methane on Mars may be the result of mineral surface-catalyzed CO2 and or CO reduction during Fisher-Tropsch Type (FTT) reactions. A better understanding of these reaction pathways and corresponding C and H isotope fractionations is critical to deciphering the synthesis of organic compounds produced under abiotic hydrothermal conditions. Described here is a technique for the extraction and analysis of both C and H isotopes from alcohols (C1-C4) and organic acids (C1-C6). This work is meant to provide a "proof of concept" for making meaningful isotope measurements on complex mixtures of solid-phase hydrocarbons and other intermediary products produced during high-temperature and high-pressure synthesis on mineral-catalyzed surfaces. These analyses are conducted entirely "on-line" utilizing a CDS model 5000 Pyroprobe connected to a Thermo Trace GC Ultra that is interfaced with a Thermo MAT 253 isotope ratio mass spectrometer operating in continuous flow mode. Also, this technique is designed to carry a split of the GC-separated product to a DSQ II quadrupole mass spectrometer as a means of making semi-quantitative compositional measurements. Therefore, both chemical and isotopic measurements can be carried out on the same sample.

Socki, Richard A.↗
DOE OSTI2021

Transcriptional and translational landscape of Candida auris in response to caspofungin

Candida auris has emerged as a serious worldwide threat by causing opportunistic infections that are frequently resistant to one or more conventional antifungal medications resulting in high mortality rates. Against this backdrop, health warnings around the world have focused efforts on understanding C. auris fungal biology and effective prevention and treatment approaches to combat this fungus. To date, there is little information about the differentially expressed genes when this fungus is treated with conventional antifungals, and caspofungin is a standard echinocandin deployed in the therapy against C. auris. In this work, we treated two distinct strains of C. auris for 24h with caspofungin, and the cellular responses were evaluated at the morphological, translational and transcriptional levels. We first observed that the echinocandin caused morphological alterations, aggregation of yeast cells, and modifications in the cell wall composition of C. auris. Transcriptomic analysis revealed an upregulation of genes related to the synthesis of the cell wall, ribosome, and cell cycle after exposure to caspofungin. Supporting these findings, the integrated proteomic analysis showed that caspofungin-treated cells were enriched in ribosome-related proteins and cell wall, especially mannoproteins. Altogether, these results provide further insights into the biology of C. auris and expands our understanding regarding the antifungal activity of caspofungin and reveal cellular targets, as the mannose metabolism, that can be further explored for the development of novel antifungals.

59 BASIC BIOLOGICAL SCIENCES↗