Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary layer flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Laminar boundary-layer solutions in three dimensions

As an alternative to pure finite-difference techniques, the Method of Integral Relations (MIR) is formulated for three-dimensional boundary-layer flows with separation, and applied to two problems. The first concerns an incompressible laminar flow over a plate with an attached cylinder, where the potential solution of the flow round the circular cylinder is used as the boundary condition. In the second application the solution to the three-dimensional boundary-layer flow over blunt bodies is discussed and results for an ellipsoid of revolution at 30 deg incidence are presented. In both cases the results are found to be in satisfactory agreement with those obtained by finite-difference methods.

Modarress, D.↗
NASA NTRS1987

Experimental evaluation of heat transfer on a 1030:1 area ratio rocket nozzle

A 1030:1 carbon steel, heat-sink nozzle was tested. The test conditions included a nominal chamber pressure of 2413 kN/sq m and a mixture ratio range of 2.78 to 5.49. The propellants were gaseous oxygen and gaseous hydrogen. Outer wall temperature measurements were used to calculate the inner wall temperature and the heat flux and heat rate to the nozzle at specified axial locations. The experimental heat fluxes were compared to those predicted by the Two-Dimensional Kinetics (TDK) computer model analysis program. When laminar boundary layer flow was assumed in the analysis, the predicted values were within 15% of the experimental values for the area ratios of 20 to 975. However, when turbulent boundary layer conditions were assumed, the predicted values were approximately 120% higher than the experimental values. A study was performed to determine if the conditions within the nozzle could sustain a laminar boundary layer. Using the flow properties predicted by TDK, the momentum-thickness Reynolds number was calculated, and the point of transition to turbulent flow was predicted. The predicted transition point was within 0.5 inches of the nozzle throat. Calculations of the acceleration parameter were then made to determine if the flow conditions could produce relaminarization of the boundary layer. It was determined that if the boundary layer flow was inclined to transition to turbulent, the acceleration conditions within the nozzle would tend to suppress turbulence and keep the flow laminar-like.

Kacynski, Kenneth J.↗
NASA NTRS1987

Experimental evaluation of heat transfer on a 1030:1 area ratio rocket nozzle

A 1030:1 carbon steel, heat-sink nozzle was tested. The test conditions included a nominal chamber pressure of 2413 kN/sq m and a mixture ratio range of 2.78 to 5.49. The propellants were gaseous oxygen and gaseous hydrogen. Outer wall temperature measurements were used to calculate the inner wall temperature and the heat flux and heat rate to the nozzle at specified axial locations. The experimental heat fluxes were compared to those predicted by the Two-Dimensional Kinetics (TDK) computer model analysis program. When laminar boundary layer flow was assumed in the analysis, the predicted values were within 15 percent of the experimental values for the area ratios of 20 to 975. However, when turbulent boundary layer conditions were assumed, the predicted values were approximately 120 percent higher than the experimental values. A study was performed to determine if the conditions within the nozzle could sustain a laminar boundary layer. Using the flow properties predicted by TDK, the momentum-thickness Reynolds number was calculated, and the point of transition to turbulent flow was predicted. The predicted transition point was within 0.5 inches of the nozzle throat. Calculations of the acceleration parameter were then made to determine if the flow conditions could produce relaminarization of the boundary layer. It was determined that if the boundary layer flow was inclined to transition to turbulent, the acceleration conditions within the nozzle would tend to suppress turbulence and keep the flow laminar-like.

Kacynski, Kenneth J.↗
NASA NTRS1978

Experimental study of the laminar-turbulent transition of a concave wall in a parallel flow

The instability of the laminar boundary layer flow along a concave wall was studied. Observations of these three-dimensional boundary layer phenomena were made using the hydrogen-bubble visualization technique. With the application of stereo-photogrammetric methods in the air-water system it was possible to investigate the flow processes qualitatively and quantitatively. In the case of a concave wall of sufficient curvature, a primary instability occurs first in the form of Goertler vortices with wave lengths depending upon the boundary layer thickness and the wall curvature. At the onset the amplification rate is in agreement with the linear theory. Later, during the non-linear amplification stage, periodic spanwise vorticity concentrations develop in the low velocity region between the longitudinal vortices. Then a meandering motion of the longitudinal vortex streets subsequently ensues, leading to turbulence.

Bippes, H.↗
NASA NTRS1990

One-equation near-wall turbulence modeling with the aid of direct simulation data

The length scales appearing in the relations for the eddy viscosity and dissipation rate in one-equation models were evaluated from direct numerical simulation data for developed channel and boundary-layer flow at two Reynolds numbers each. To prepare the ground for the evaluation, the distribution of the most relevant mean-flow and turbulence quantities is presented and discussed with respect to Reynolds-number influence and to differences between channel and boundary-layer flow. An alternative model is also examined in which bar-(v'(exp 2))(exp 1/2) is used as velocity scale instead of k(exp 1/2). With this velocity scale, the length scales now appearing in the model follow very closely a linear relationship near the wall so that no damping is necessary. For the determination of bar-v'(exp 2) in the context of a one-equation model, a correlation is provided between bar-(v'(exp 2))/k and bar-(u'v')/k.

Rodi, W.↗
NASA NTRS1968

Survey of the Relationship Between Theory and Experiment for Convective Heat Transfer From Rocket Combustion Gases

The problem of predicting the distribution of heat flux in a rocket engine is complicated by a flow field and thermodynamics so perturbed by as yet indescribable combustion effects that it continues to be necessary to utilize a simplified theoretical model against which to compare experimental results in order to gain insight. The most successful model applied to this problem is that of a compressible, turbulent, accelerating boundary layer flow with an arbitrary point of origin, and chemical reaction restricted to equilibrium recombination or diffusion-limited recombination on a catalytic wall. Analysis of this model was not possible without making several assumptions about the nature of the skin friction coefficient relationship and Reynold's analogy in an accelerating boundary layer flow. The paper summarizes the analysis of this model (together with detailed treatment of the special problems of variable properties, chemical reaction, and sources of transport properties), and describes several closed-form equations that have also been developed and applied to the problem. Described are results of several experiments with hot air flow made for the purpose of checking the validity of the assumptions in the boundary layer analysis. Most significant, however, are presentations of sample distributions of local heat flux measured in rocket engines operating with a wide range of conditions, propellants, injectors and sizes. When compared with predictions, these data show the significant range of deviation in heat flux that results from the combustion effects and which precludes a generally accurate prediction theory or correlation equation until the combustion process itself is correlated.

D R Bartz↗
NASA NTRS1988

A simple, analytic 3-dimensional downburst model based on boundary layer stagnation flow

A simple downburst model is developed for use in batch and real-time piloted simulation studies of guidance strategies for terminal area transport aircraft operations in wind shear conditions. The model represents an axisymmetric stagnation point flow, based on velocity profiles from the Terminal Area Simulation System (TASS) model developed by Proctor and satisfies the mass continuity equation in cylindrical coordinates. Altitude dependence, including boundary layer effects near the ground, closely matches real-world measurements, as do the increase, peak, and decay of outflow and downflow with increasing distance from the downburst center. Equations for horizontal and vertical winds were derived, and found to be infinitely differentiable, with no singular points existent in the flow field. In addition, a simple relationship exists among the ratio of maximum horizontal to vertical velocities, the downdraft radius, depth of outflow, and altitude of maximum outflow. In use, a microburst can be modeled by specifying four characteristic parameters, velocity components in the x, y and z directions, and the corresponding nine partial derivatives are obtained easily from the velocity equations.

Oseguera, Rosa M.↗
NASA NTRS2012

Transition Within Leeward Plane of Axisymmetric Bodies at Incidence in Supersonic Flow

Boundary layer transition along the leeward symmetry plane of axisymmetric bodies at nonzero angle of attack in supersonic flow was investigated experimentally and numerically as part of joint research between the Japan Aerospace Exploration Agency (JAXA) and National Aeronautics and Space Administration (NASA). Transition over four axisymmetric bodies (namely, Sears-Haack body, semi-Sears-Haack body, straight cone and flared cone) with different axial pressure gradients was measured in two different facilities with different unit Reynolds numbers. The semi-Sears-Haack body and flared cone were designed at JAXA to broaden the range of axial pressure distributions. For a body shape with an adverse pressure gradient (i.e., flared cone), the experimentally measured transition patterns show an earlier transition location along the leeward symmetry plane in comparison with the neighboring azimuthal locations. For nearly zero pressure gradient (i.e.,straight cone), this feature is only observed at the larger unit Reynolds number. Later transition along the leeward plane was observed for the remaining two body shapes with a favorable pressure gradient. The observed transition patterns are only partially consistent with the numerical predictions based on linear stability analysis. Additional measurements are used in conjunction with the stability computations to explore the phenomenon of leeward line transition and the underlying transition mechanism in further detail.

Tokugawa, Naoko↗
NASA NTRS1982

Preston tube calibrations and direct force floating element measurements in a two-dimensional turbulent boundary layer

Preston tubes provide a convenient means of estimating local wall shear stress. Practical difficulties arise from a lack of calibration data obtained in turbulent boundary layer flows and from the wide choice of calibration equations available mainly from pipe flow calibrations. The results of an experimental study comparing a large number of direct force local wall shear stress measurements in a near-zero pressure gradient two-dimensional turbulent boundary layer flow are presented. The results indicate that there is consistent and excellent agreement between the Patel intermediate calibration formula and the direct force measurements. Typical differences among the direct force measurements and several other proposed calibration equations are also shown.

Mcallister, J. E.↗
NASA NTRS1978

Aerothermodynamic assessment of corrugated panel thermal protection systems

The results of an analysis of wind-tunnel data for the effect of wave shape on local boundary layer flows and heat transfer are used to assess the feasibility of using corrugated panels on a Single-Stage-To-Orbit (SSTO) vehicle. In the flight assessment, available engineering design procedures are used to compute the inviscid and boundary layer flow for a given flight trajectory. The flight vehicle flow field calculations are then used in conjunction with wind-tunnel corrugated panel heating data correlations to examine the heating penalties associated with using corrugated panels at a number of locations on the vehicle. Severe heating penalties, as a result of the corrugations, were found over large areas of the windward surface. Maximum surface temperature penalties ranged from 100K to 500K and very large structural advantages for the corrugations would be required to override the heating penalties. Computed peak corrugation temperatures were within allowable limits of the equivalent smooth wall material for most leeward and side fuselage locations and corrugated panels will be most likely limited to these locations.

Brandon, H. J.↗
NASA NTRS1979

Prediction of compliant wall drag reduction, part 2

A numerical model of turbulent boundary layer flows over compliant walls was investigated. The model is based on Burton's observation that outer flow structures in turbulent boundary layers produce large scale pressure fluctuations near the wall. The results of calculations indicate that certain small wavelength wall motions can have a significant effect upon the stability of turbulent boundary layers.

Orszag, S. A.↗
NASA NTRS1992

Turbulence modeling for hypersonic flows

Turbulence modeling for high-speed compressible flows is described and discussed. Starting with the compressible Navier-Stokes equations, methods of statistical averaging are described by means of which the Reynolds-averaged Navier-Stokes equations are developed. Unknown averages in these equations are approximated using various closure concepts. Zero-, one-, and two-equation eddy viscosity models, algebraic stress models, and Reynolds stress transport models are discussed. Computations of supersonic and hypersonic flows obtained using several of the models are discussed and compared with experimental results. Specific examples include attached boundary-layer flows, shock-wave boundary-layer interactions, and compressible shear layers. From these examples, conclusions regarding the status of modeling and recommendations for future studies are discussed.

Marvin, J. G.↗
NASA NTRS2018

Instability Wave–Streak Interactions in a High Mach Number Boundary Layer at Flight Conditions

The interaction of stationary streaks undergoing nonmodal growth with modally unstable instability waves in a hypersonic boundary-layer flow is studied using numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment; namely, a 7 degree half-angle, circular cone with 2.5 mm nose radius, freestream Mach number equal to 5.30, unit Reynolds number equal to 13.42 m -1 , and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the vehicle. This paper investigates the nonlinear evolution of initially linear optimal disturbances that evolve into finite-amplitude streaks, followed by an analysis of the modal instability characteristics of the perturbed, streaky boundary-layer flow. The investigation is performed with stationary direct numerical simulations (DNS) and plane-marching parabolized stability equations (PSE), in conjunction with partial-differential-equation-based planar eigenvalue analysis. The overall effect of streaks is to reduce the peak amplification factors of instability waves, indicating a possible downstream shift in the onset of laminar-turbulent transition. The present study confirms previous findings that the mean flow distortion of the nonlinear streak perturbation reduces the amplification rates of the Mack-mode instability. More importantly, however, the present results demonstrate that the spanwise varying component of the streak can produce a larger effect on the Mack-mode amplification. The study with selected azimuthal wavenumbers for the stationary streaks reveals that a wavenumber of approximately 1.4 times larger than the optimal wavenumber is more effective in stabilizing the planar Mack-mode instabilities. In the absence of unstable first-mode waves for the present cold-wall condition, transition onset is expected to be delayed until the peak streak amplitude increases to nearly 35 percent of the freestream velocity, when intrinsic instabilities of the boundary-layer streaks begin to dominate the transition process. For streak amplitudes below that limit a significant net stabilization is achieved, yielding a potential transition delay that can exceed 100 percent of the length of the laminar region in the uncontrolled case.

Boundary layer stability↗
NASA NTRS2014

Numerical Simulation of Boundary Layer Ingesting (BLI) Inlet-Fan Interaction

Future civil transport designs may incorporate engine inlets integrated into the body of the aircraft to take advantage of efficiency increases due to weight and drag reduction. Additional increases in engine efficiency are predicted if the inlet ingests the lower momentum boundary layer flow. Previous studies have shown, however, that efficiency benefits of Boundary Layer Ingesting (BLI) ingestion are very sensitive to the magnitude of fan and duct losses, and blade structural response to the non-uniform flow field that results from a BLI inlet has not been studied in-depth. This paper presents an effort to extend the modeling capabilities of an existing rotating turbomachinery unsteady analysis code to include the ability to solve the external and internal flow fields of a BLI inlet. The TURBO code has been a successful tool in evaluating fan response to flow distortions for traditional engine/inlet integrations, such as the development of rotating stall and inlet distortion through compressor stages. This paper describes the first phase of an effort to extend the TURBO model to calculate the external and inlet flowfield upstream of fan so that accurate pressure distortions that result from BLI configurations can be computed and used to analyze fan aerodynamics and structural response. To validate the TURBO program modifications for the BLI flowfield, experimental test data obtained by NASA for a flushmounted S-duct with large amounts of boundary layer ingestion was modeled. Results for the flow upstream and in the inlet are presented and compared to experimental data for several high Reynolds number flows to validate the modifications to the solver. Quantitative data is presented that indicates good predictive capability of the model in the upstream flow. A representative fan is attached to the inlet and results are presented for the coupled inlet/fan model. The impact on the total pressure distortion at the AIP after the fan is attached is examined.

Inlet Fan Interactions↗
NASA NTRS1972

Boundary layer stability on a yawed spinning body of revolution and its effect on the magnus force and moment

The parameters are established which are important to the stability of a boundary layer flow over a yawed spinning cylinder in a uniform stream. It is shown that transition occurs asymmetrically in general and this asymmetry can be important for the prediction of aerodynamic forces and moments (e.g., the Magnus effect). Instability of the steady-state boundary layer flow is determined using small disturbance theory. Although the approach is strictly valid only for the calculation of the conditions for stability in the small, experimental data indicate that in many problems, it provides a good estimate for the transition to turbulence.

Jacobson, I. D.↗
NASA NTRS1974

Comparison of theoretical and experimental boundary-layer development in a Mach 2.5 mixed-compression inlet

An analytical investigation was made of the boundary layer flow in an axisymmetric Mach 2.5 mixed compression inlet, and the results were compared with experimental measurements. The inlet tests were conducted in the Lewis 10- by 10-foot supersonic wind tunnel at a unit Reynolds number of 8.2 million/m. The inlet incorporated porous bleed regions for boundary layer control, and the effect of this bleed was taken into account in the analysis. The experimental boundary layer data were analyzed by using similarity laws from which the skin friction coefficient was obtained. The boundary layer analysis included predictions of laminar and turbulent boundary layer growth, transition, and the effects of the shock boundary layer interactions. In addition, the surface static pressures were compared with those obtained from an inviscid characteristics program. The results of investigation showed that the analytical techniques gave satisfactory predictions of the boundary layer flow except in regions that were badly distorted by the terminal shock.

Hingst, W. R.↗