SEARCH · Engineering Papers

Results for “Aircraft airspeed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Development of wing and tail configurations for low altitude unmanned research aircraft (LAURA)

The Low Altitude/Airspeed Unmanned Research Aircraft (LAURA) is being developed by the U.S. Navy for flight test research using low-Reynolds number airfoils. This vehicle consists of a standard modular fuselage designed to accept the installation of several wings/tails having low Reynolds number airfoils, and various planform shapes. Design constraints include shipboard storage, long flight endurance at very low airspeeds and sea-skimming cruise altitude. The stringent design constraints require the development of high-performance low Reynolds number (LRN) airfoils, suitable lifting surface configuration, and advanced airframe-propulsion systems. The present paper describes ongoing efforts to develop wing and tail configurations for LAURA using airfoils designed at NASA Langley Research Center.

Mangalam, S. M.↗

NASA NTRS1974

Statistical analysis of general aviation VG-VGH data

To represent the loads spectra of general aviation aircraft operating in the Continental United States, VG and VGH data collected since 1963 in eight operational categories were processed and analyzed. Adequacy of data sample and current operational categories, and parameter distributions required for valid data extrapolation were studied along with envelopes of equal probability of exceeding the normal load factor (n sub z) versus airspeed for gust and maneuver loads and the probability of exceeding current design maneuver, gust, and landing impact n sub z limits. The significant findings are included.

Clay, L. E.↗

NASA NTRS1984

A Fault Tolerant System for an Integrated Avionics Sensor Configuration

An aircraft sensor fault tolerant system methodology for the Transport Systems Research Vehicle in a Microwave Landing System (MLS) environment is described. The fault tolerant system provides reliable estimates in the presence of possible failures both in ground-based navigation aids, and in on-board flight control and inertial sensors. Sensor failures are identified by utilizing the analytic relationships between the various sensors arising from the aircraft point mass equations of motion. The estimation and failure detection performance of the software implementation (called FINDS) of the developed system was analyzed on a nonlinear digital simulation of the research aircraft. Simulation results showing the detection performance of FINDS, using a dual redundant sensor compliment, are presented for bias, hardover, null, ramp, increased noise and scale factor failures. In general, the results show that FINDS can distinguish between normal operating sensor errors and failures while providing an excellent detection speed for bias failures in the MLS, indicated airspeed, attitude and radar altimeter sensors.

Caglayan, A. K.↗

NASA NTRS1992

Development of the Advance Warning Airborne System(AWAS)

The thermal characteristics of microbursts are utilized by the AWAS IR and OAT features to provide predictive warning of hazardous microbursts ahead of the aircraft during landing or take off. The AWAS was evaluated satisfactorily in 1990 on a Cessna Citation that was intentionally flown into a number of wind shear events. The events were detected, and both the IR and OAT thermal features were shown to be effective. In 1991, AWAS units were flown on three American Airline MD-80's and three Northwest Airlines DC-9's to study and to decrease the nuisance alert response of the system. The AWAS was also flown on the NASA B737 during the summer of 1991. The results of these flights were inconclusive and disappointing. The results were not as promising as before because NASA conducted research flights which were outside of the normal operating envelope for which the AWAS is designed to operate. In an attempt to compensate for these differences in airspeed and mounting location, the automatic features of the system were sometimes overridden by NASA personnel during the flight. Each of these critical factors is discussed in detail. The effect of rain on the OAT signals is presented as a function of the air speed. Use of a 4 pole 1/20 Hertz filter is demonstrated by both the IR and thermal data. Participation in the NASA 1992 program was discussed. FAA direction in the continuing Certification program requires the addition of a reactive feature to the AWAS predictive system. This combined system will not require flight guidance on newer aircraft. The features of AWAS-IV, with the NASA algorithm included, were presented. Expected completion of the FAA Certification plan was also described.

Adamson, H. Patrick↗

NASA NTRS1974

Applications of fluidics to light aircraft instrumentation and control

Review of a program for the development of advanced fluidic components and the application of these components to general aviation instrumentation and control. The major project in this category has been the development of a simple, reliable, two-axis autopilot for light aircraft, using a fluidic inertial rate sensor for stability and roll attitude control, and a simple magnetometer for azimuth reference. This autopilot has been succesfully flight-tested. Fluidic hardware developed for this autopilot is described, and projected improvements and extensions are discussed. Application of fluidic components to such flight instruments as turn coordinators, artificial horizons, and true airspeed indicators is explored.

Garner, H. D.↗

NASA NTRS1982

Boeing 234 flight control development

The Boeing 234 is the commercially certified derivative of the CH-47 Chinook. The automatic flight control system and flight director with coupler were designed to reduce pilot work-load for missions of approximately six hour duration during VFR, IFR, day and night conditions. The AFCS system for the 234 is essentially the same system as developed for the CH-47D, which has airspeed hold, attitude hold, and maneuver enhancement in all three axes. The system also has the capability to couple to the Sperry Helcis flight director system which provides for enroute navigation and landing approaches. Certification testing was completed, by both the FAA and CAA, to FAR Part 29 for Transport Category Rotorcraft and BCAR Section G: Rotorcraft. The aircraft was certified for civil operation in June 1981.

Morris, J. J.↗

NASA NTRS2004

Tiperon

A control surface for an air vehicle (e.g., an aircraft, rocket, or missile) is useful for flight control at both subsonic and supersonic speeds. The control surface defines the outboardmost tip of a flight structure (e.g., a wing, tail or other stabilizer) of the air vehicle. Hence, the control surface is referred to as a `tiperon`. The tiperon has an approximately L-shaped configuration, and can be rotated relative to a fixed portion of the flight structure about a control axis. The respective surface areas of the tiperon sections forward and aft of the control axis are proportioned to place the subsonic center of pressure aft of the control axis to enhance aircraft control, and preferably also forward of the centroid of tiperon surface area. Also, the control surface sections forward and aft of the control axis are preferably mass-balanced, or at least nearly so, to enhance aircraft control at supersonic speeds. Either of the tiperon sections forward and aft of the control axis can be tapered to reduce the dependence of the moment exerted by air flow about the control axis, upon the tiperon's angle-of-attack. The tiperon also has enough surface area to control the air vehicle, even at low airspeeds. The invention is also directed to air vehicles incorporating one or more such control surfaces.

Lewis, Carl E.↗

NASA NTRS1972

A simulator evaluation of the use of spoilers on a light aircraft

A fixed-base flight simulator was used to evaluate wing spoilers for longitudinal flight path control on a modified Cessna Cardinal aircraft. Spoilers which generated the proper pitching moment to maintain aircraft trim C sub L constant could be used as an effective descent rate control. More than 100 simulated ILS approaches were flown by evaluation pilots using both conventional methods and spoiler descent rate control. Three spoiler control schemes were evaluated during the ILS approaches. Using the spoilers for control, instrument approaches could be flown smoothly and precisely with constant airspeed and pitch attitude. While the spoilers could adequately control ILS approaches, a spoiler system with greater authority would be desirable for use in visual approaches.

Brainerd, C. H.↗

NASA NTRS1947

Flight Comparison of Performance and Cooling Characteristics of Exhaust-Ejector Installation with Exhaust-Collector-Ring Installation

Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.

Acker, Loren W.↗

NASA NTRS1989

Aeroservoelastic tailoring for lateral control enhancement

The need for effective aileron power for aircraft lateral control and turning maneuvers dates back to the Wright Brothers and their wing warping concept for active stabilization of their aircraft. Early researchers in Great Britain, Japan, Germany and the United States explored ways to increase the effectiveness of control aileron to generate a roll moment. The basic problem of aileron effectiveness and the interrelationship between structural distortion and the loads applied by the control surface is illustrated. A rigid wing/aileron surface will develop the capability to generate increased roll rates as airspeed increases. A flexible surface will become less effective as airspeed increases because of the twisting distortion created by the aft-mounted control surface. This tendency is further worsened by bending distortion of an aft swept wing. This study focuses its attention on the ability of a combined effort between structural redesign of a wing and sizing and placement of a control surface to create specified roll performance with a minimum hinge moment. This design optimization problem indicates the advantages of simultaneous consideration of structural design and control design.

Weisshaar, Terrence A.↗

NASA NTRS1984

An Automated Stall-Speed Warning System

The NASA Dryden Flight Research Facility embarked upon a project with the United States Army Aviation Engineering Flight Activity (USAAEFA) to develop and test a stall-speed warning system. NASA designed and built an automated stall-speed warning system which presents both airspeed and stall speed to the pilot. The airspeed and stall speed are computed in real time by monitoring the basic aerodynamic parameters {dynamic pressure, horizontal and vertical accelerations, and pressure altitude) and other parameters (elevator and flap positions, engine torques, and fuel flow). In addition, an aural warning at predetermined stall margins is presented to the pilot through a voice synthesizer. Once the system was designed and installed in the aircraft, a flight-test program of less than 20 hr was anticipated to determine the stall-speed software coefficients. These coefficients would then be inserted in the system's software and then test flown over a period of about 10 hr for the purposes of evaluation.

Pilot↗

NASA NTRS1983

An Automated Stall-Speed Warning System

The NASA Dryden Flight Research Facility embarked upon a project with the United States Army Aviation Engineering Flight Activity (USAAEFA) to develop and test a stall-speed warning system. NASA designed and built an automated stall-speed warning system which presents both airspeed and stall speed to the pilot. The airspeed and stall speed are computed in real time by monitoring the basic aerodynamic parameters (dynamic pressure, horizontal and vertical accelerations, and pressure altitude) and other parameters (elevator and flap positions, engine torques, and fuel flow). In addition, an aural warning at predetermined stall margins is presented to the pilot through a voice synthesizer. Once the system was designed and installed in the aircraft, a flight-test program of less than 20 hr was anticipated to determine the stall-speed software coefficients. These coefficients would then be inserted in the system's software and then test flown over a period of about 10 hr for the purposes of evaluation.

Dynamic Pressure↗

NASA NTRS1960

A Flight Study of a Power-Off Landing Technique Applicable to Re-Entry Vehicles

A power-off landing technique, applicable to aircraft of configurations presently being considered for manned re-entry vehicles, has been developed and flight tested at Ames Research Center. The flight tests used two configurations of an airplane for which the values of maximum lift-drag ratios were 4.0 and 2.8. Twenty-four idle-power approaches were made to an 8000-foot runway with touchdown point and airspeed accuracies of +/-600 feet and +/-10 knots, respectively. The landing pattern used was designed to provide an explicitly defined flight path for the pilot and, yet, to require no external guidance other than the pilot's view from the cockpit. The initial phase of the approach pattern is a constant high-speed descent from altitude aimed at a ground reference point short of the runway threshold. At a specified altitude and speed, a constant g pull-out is made to a shallow flight path along which the air-plane decelerates to the touchdown point. Repeatability and safety are inherent because of the reduced number of variables requiring pilot judgment, and because of the fact that a missed approach is evident at speeds and altitudes suitable for safe ejection. The accuracy and repeatability of the pattern are indicated by the measured results. The proposed pattern appears to be particularly suitable for configurations having unusual drag variations with speed in the lower speed regime, since the pilot is not required to control speed in the latter portions of the pattern.

Bray, Richard S.↗

NASA NTRS1993

Reduction of structural loads using maneuver load control on the Advanced Fighter Technology Integration (AFTI)/F-111 mission adaptive wing

A transonic fighter-bomber aircraft, having a swept supercritical wing with smooth variable-camber flaps was fitted with a maneuver load control (MLC) system that implements a technique to reduce the inboard bending moments in the wing by shifting the spanwise load distribution inboard as load factor increases. The technique modifies the spanwise camber distribution by automatically commanding flap position as a function of flap position, true airspeed, Mach number, dynamic pressure, normal acceleration, and wing sweep position. Flight test structural loads data were obtained for loads in both the wing box and the wing root. Data from uniformly deflected flaps were compared with data from flaps in the MLC configuration where the outboard segment of three flap segments was deflected downward less than the two inboard segments. The changes in the shear loads in the forward wing spar and at the roots of the stabilators also are presented. The camber control system automatically reconfigures the flaps through varied flight conditions. Configurations having both moderate and full trailing-edge flap deflection were tested. Flight test data were collected at Mach numbers of 0.6, 0.7, 0.8, and 0.9 and dynamic pressures of 300, 450, 600, and 800 lb/sq ft. The Reynolds numbers for these flight conditions ranged from 26 x 10(exp 6) to 54 x 10(exp 6) at the mean aerodynamic chord. Load factor increases of up to 1.0 g achieved with no increase in wing root bending moment with the MLC flap configuration.

Thornton, Stephen V.↗

NASA NTRS2024

Assessment of Secondary Pitot Probe Locations on a Small UAS

Urban Air Mobility (UAM) and Advanced Air Mobility (AAM) have been at the forefront of many aeronautical discussions because of the potential revolutionary improvement to urban transportation. In this study, a representative Research Aircraft for eVTOL Enabling techNologies, Sub-scale Wind Tunnel Flight Test (RAVEN SWFT) nosecone was placed inside the NASA Langley Research Center’s 12-Foot Low-Speed Wind Tunnel with a pitot-static assembly installed. The study aimed to determine a suitable location and orientation of the pitot-static assembly on the nose of the vehicle, which consists of two airspeed sensors: one for the flight controller and one for data collection. The dynamic pressure was varied from 0.5 to 5psf for each test point. Additionally, three different offset distances from the center boom and three different angles for the flight controller pitot tube were tested. The data from both of the pitot tube assemblies were compared to the wind tunnel and the Aeroprobe pitot tube. The results show the flight controller pitot tube performs better when it is placed further away from the nosecone, regardless of the angle. The results also show that the angle does not affect the accuracy of the pitot tube when the vehicle yaws or pitches regardless of the mounting angle and location. The study provides useful insights for the design of the airspeed measurement systems on small Uncrewed Aerial Systems (sUAS), which can be applied to other UAM and AAM applications.

AAM↗

NASA NTRS1961

An Analytical Treatment of Aircraft Propeller Precession Instability

An analytical investigation is made of a precession-type instability which can occur in a flexibly supported aircraft-engine-propeller combination. By means of an idealized mathematical model which is comprised of a rigid power-plant system flexibly mounted in pitch and yaw to a fixed backup structure, the conditions required for neutral stability are determined. The paper also examines the sensitivity of the stability boundaries to changes in such parameters as stiffness, damping, and asymmetries in the engine mount, propeller speed, airspeed, Mach number, propeller thrust, and location of pitch and yaw axes. Stability is found to depend strongly on the damping and stiffness in the system. With the use of nondimensional charts, theoretical stability boundaries are compared with experimental results obtained in wind-tunnel tests of an aeroelastic airplane model. In general, the theoretical results, which do not account for wing response, show the same trends as observed experimentally; however, for a given set of conditions calculated airspeeds for neutral stability are consistently lower than the measured values. Evidently, this result is due to the fact that wing response tends to add damping to the system.

Reed, Wilmer H., III↗

NASA NTRS1983

Dynamic assessment of B-52B-008 carrier aircraft for the revised Space Shuttle solid rocket booster decelerator subsystem drop test vehicle

The structural integrity of B-52B-008, pylon, and hooks for the drop test missions was determined by theoretical analysis. The results of the analysis and conclusions are presented in this document. The major modification to the drop test vehicle was shortening it about 54 inches, which resulted in the forward hook attach structure being located at the base of the nosecone. The shims that are located in the aft hook structures are increased from two inches to three inches. Airspeed, aerodynamic configuration, and load charts are included.

Doty, L. J.↗

NASA NTRS2014

Failure Investigation of WB-57 Aircraft Engine Cowling

The NASA Johnson Space Center (JSC) in Houston, Texas is the home of the NASA WB-57 High Altitude Research Program. Three fully operational WB-57 aircraft are based near JSC at Ellington Field. The aircraft have been flying research missions since the early 1960's, and continue to be an asset to the scientific community with professional, reliable, customer-oriented service designed to meet all scientific objectives. The NASA WB-57 Program provides unique, high-altitude airborne platforms to US Government agencies, academic institutions, and commercial customers in order to support scientific research and advanced technology development and testing at locations around the world. Mission examples include atmospheric and earth science, ground mapping, cosmic dust collection, rocket launch support, and test bed operations for future airborne or spaceborne systems. During the return from a 6 hour flight, at 30,000 feet, in the clean configuration, traveling at 175 knots indicated airspeed, in un-accelerated flight with the auto pilot engaged, in calm air, the 2-man crew heard a mechanical bang and felt a slight shudder followed by a few seconds of high frequency vibration. The crew did not notice any other abnormalities leading up to, or for the remaining 1 hour of flight and made an uneventful landing. Upon taxi into the chocks, the recovery ground crew noticed the high frequency long wire antenna had become disconnected from the vertical stabilizer and was trailing over the left inboard wing, and that the left engine upper center removable cowling panel was missing, with noticeable damage to the left engine inboard cowling fixed structure. The missing cowling panel was never recovered. Each engine cowling panel is attached to the engine nacelle using six bushings made of 17-4 PH steel. The cylinder portions of four of the six bushings were found still attached to the aircraft (Fig 1). The other two bushings were lost with the panel. The other four bushings exhibited ratchet marks (multiple fatigue origins) which initiated in the sharp radius of the flange/cylinder fillet and were observed 300 degrees around the flange perimeter (Fig 2-3). Low stress, high cycle fatigue (HCF) was observed on the fracture surfaces of all four bushings (Fig 4). To improve the cowling panel joint design and enable return to flight, new cowling bushings with thicker flanges and a larger machined flange/cylinder fillet radius were installed on all cowling panels. In addition, a spacer was added to the joint to achieve the proper stack tolerance. Finally, a time change requirement for all cowling bushings was instituted.

Martinez, J. E.↗