Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Utah FORGE: Fault Reactivation Through Fluid Injection Induced Seismicity Laboratory Experiments

Included are results from shear reactivation experiments on laboratory faults pre-loaded close to failure and reactivated by the injection of fluid into the fault. The sample comprises a single-inclined-fracture (SIF) transecting a cylindrical sample of Westerly granite. All experiments are conducted at ambient temperature and follow a similar protocol: (i) application of confining stresses (3MPa) on the fault fully saturated with DI water, (ii) shear-mobilization through the increase of axial loading at a constant displacement rate until a post-peak steady-state condition is reached, (iii) reduction of axial loading and related shear stress to a prescribed fraction of the peak steady-state frictional strength (typically 60% to 90%, representing intermediate to high magnitudes) and (iv), fault reactivation triggered by a stepwise increase of pore pressure on the fault in 0.1 MPa increments held constant for 1-5 minutes. Mechanical data from three ISCO pumps connected to a Temco pressure vessel measure axial, confining, and fault-related parameters, including fluid pressure (kPa), fluid flow rate (mL/min), and axial displacement (mm). See included code for initial data analysis and visualization for select experiments. Resource names represent experiment numbers found in the "Read Me" file, which describes each experimental setup and parameters.

15 GEOTHERMAL ENERGY↗

Unveiling damage mechanisms of chromium-coated zirconium-based fuel claddings at LWR operating temperature by in-situ digital image correlation

Here, we investigate the coupled thermomechanical fracture mechanisms of coated nuclear fuel claddings at Light Water Reactor (LWR) operating temperatures. These coated claddings are a highly attractive, near-term solution, which addresses the demands for accident-tolerant fuel systems and provide greater oxidation resistance. However, the fracture mechanisms of these coatings, which may create channels for oxidation ingression, must be fully understood prior to implementation. Thus, high-temperature expanding plug experiments were conducted on coated cladding specimens at a temperature of 315 °C, consistent with the operating environment of LWRs. Furthermore, in-situ thermomechanical deformation was measured with stereo digital image correlation during heating and mechanical testing to separately resolve contributions of thermal and mechanical strain. Digital image correlation, supported by acoustic emissions (AE) detection, was also leveraged to track cracking activity during loading. Coating fracture was found to initiate at total hoop strains of 0.34%. The thermal deformation of the coated claddings was investigated via finite element simulations, revealing a bidirectional stress-state within the coating with axial and circumferential strains of 0.026 and 0.031%. This bidirectional stress-state was attributed with the generation of off-axis fracture pattern within the coating as identified via post-experiment scanning electron microscopy. Thus, this study unveiled critical, coupled thermomechanical mechanisms governing the coating fracture of coated claddings at LWR temperatures.

36 MATERIALS SCIENCE↗

Three-dimensional continuum point cloud method for large deformation and its verification

This study presents a strong form based meshfree collocation method, which is named Continuum Point Cloud Method, to solve nonlinear field equations derived from classical mechanics for deformed bodies in three-dimensional Euclidean space. The method and its implementation are benchmarked against a nonlinear vector field using manufactured solutions. The analysis of mechanical fields firstly focuses on the study of St. Venant Kirchhoff and compressible neo-Hookean materials. Results for various initial boundary value problems are presented, including benchmark cases involving unidirectional tension and simple shear. Subsequently, the study concludes with an analysis of a displacement-controlled simulation of a compressible neo-Hookean material, specifically a bar that is pulled to 50% of its original length and rotated 90°. The pure tension case yields a 1.5% error in displacement between computed and expected values and a combined tension and torsion loading case provides further insight into material behavior under complex loading conditions. The resulting normal axial and transverse stress-strain curves are also presented. Lastly, the consistency and robustness of the proposed nonlinear numerical schemes are successfully demonstrated through various numerical experiments.

Compressible neo-Hookean materials↗

Integration of triaxial testing and pore-scale visualization of methane hydrate bearing sediments

Understanding mechanical interactions between hydrate and hosting sediments is critical for evaluating formation stability and associated environmental impacts of hydrate-bearing sediments during gas production. While core-scale studies of hydrate-bearing sediments are readily available and some explanations of observed results rely on pore-scale behavior of hydrate, actual pore-scale observations supporting the larger-scale phenomena are rarely available for hydrate-bearing sediments, especially with methane as guest molecules. The primary reasons for the scarcity include the challenge of developing tools for small-scale testing apparatus and pore-scale visualization capability. We present a testing assembly that combines pore-scale visualization and triaxial test capability of methane hydrate-bearing sediments. This testing assembly allows temperature regulation and independent control of four pressures: influent and effluent pore pressure, confining pressure, and axial pressure. Axial and lateral effective stresses can be applied independently to a 9.5 mm diameter and 19 mm long specimen while the pore pressure and temperature are controlled to maintain the stability of methane hydrate. The testing assembly also includes an X-ray transparent beryllium core holder so that 3D computed tomography scanning can be conducted during the triaxial loading. This testing assembly permits pore-scale exploration of hydrate-sediment interaction in addition to the traditional stress-strain relationship. Exemplary outcomes are presented to demonstrate applications of the testing assembly on geomechanical property estimations of methane-hydrate bearing sediments.

Seol, Yongkoo (ORCID:0000000295163405)↗

Enhancements to BISON U-Zr Metallic Fuel X447 Example Problem

As development of a metallic fuel modeling capability in BISON has progressed, the need for an example problem used as a comparison basis was observed. Collaborative work between researchers at Los Alamos National Laboratory (LANL) and Idaho National Laboratory (INL) then proceeded to determine a viable rod to use as the basis and create a BISON input deck utilizing as many metallic fuel models as feasible. The basis chosen was what would be considered a generic rod from subassembly X447, an assembly irradiated in EBR-II towards the end of its operating life, heavily based on reported data for fuel pin DP11. Thus, the approach was adopted to use flow characteristics from subassembly X447 as a basis for the convective heat transfer solution, power history and axial power profiles that are representative of rod DP11 from subassembly X447. The rod simulated is a U-10Zr wt% (U-22.5Zr at%) composition. A 2D-RZ mesh would be used to capture axial thermal hydraulic effects, axial swelling and stress-strain calculations over the full length of the rod. After initial work was invested, a refinement of the various models and input parameters was conducted to ensure consistency between operator-declared conditions, model input requirements and those represented in the example problem. This report serves as a synopsis of the enhancements and refinements to the example problem conducted throughout the 2016 fiscal year.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

THERMAL BUCKLING OF CYLINDERS

Several theoretical and experimental investigations on the buckling of cylinders due to both axial and circumferential thermal stresses are reviewed. Differences that exist among the various results are discussed and areas of future work are indicated.

CYLINDER↗

Investigation of counterflow shear effects in heat pipes

The entrainment-shear performance limit in heat pipes is investigated. The entrainment heat flux limit is defined as the condition where the Weber number is greater than or equal to one. In this analysis, the critical value for the entrainment Weber number is between 2pi and 3pi. Performance degradation due to vapor-liquid shearing stress is predicted. Preliminary qualitative experiments were conducted to observe the shear stress wave formation phenomena. The equations presented may be used to predict and minimize the vapor-liquid shear stress performance effects in axial groove and puddle flow artery heat pipes.

Feldman, K. T., Jr.↗

Micromechanical predictions of crack initiation, propagation and crack growth resistance in boron/aluminum composites

An elastoplastic, axisymmetric finite element model has been used to predict the initiation and propagation of a crack in a composite model consisting of a single broken boron fiber embedded in an annular sheath of aluminum matrix. The accuracy of the axisymmetric finite element model for crack problems has been established by solving the classical problem of a penny-shaped crack in a thick cylindrical rod under axial tension. Also, the stress intensity factors predicted by the present numerical model are compared with continuum results. A constant displacement boundary condition applied during an increment of crack growth permits a substantial amount of stable crack growth in the matrix material. The concept of Crack Growth Resistance Curves (KR-curves) has been used to determine the point of crack instability

Mahishi, J. M.↗

Bulk Growth of 2-6 Crystals in the Microgravity Environment of USML-1

The first United States Microgravity Laboratory Mission (USML- 1) flew in June 1992 on the Space Shuttle Columbia. An important part of this SpaceLab mission was the debut of the Crystal Growth Furnace (CGF). Of the seven samples grown in the furnace, three were bulk grown 2-6 compounds, two of a cadmium zinc telluride alloy, and one of a mercury zinc telluride alloy. Ground based results are presented, together with the results of computer simulated growths of these experimental conditions. Preliminary characterization results for the three USML-1 growth runs are also presented and the flight sample characteristics are compared to the equivalent ground truth samples. Of particular interest are the effect of the containment vessel on surface features, and especially on the nucleation, and the effect of the gravity vector on radial and axial compositional variations and stress and defect levels.

Gillies, Donald C.↗

Lubricated Bearing Lifetimes of a Multiply Alkylated Cyclopentane and a Linear Perfluoropolyether Fluid in Oscillatory Motion at Elevated Temperatures in Ultrahigh Vacuum

Bearing life tests in vacuum with three space liquid lubricants, two multiply alkylated cyclopentanes (MACs) and a linear perfluoropolyether (PFPE) were performed. Test conditions included: an 89 N axial load (mean Hertzian stress 0.66 GPa), vacuum level below 7x10(exp -4) Pa, and a +/-30deg dither angle. Dither rate was 75 cycles per minute. Higher (110 to 122 C) and lower temperature tests (75 C) were performed. For the higher temperature tests, the PFPE, Fomblin (Ausimont SpA) Z25 outperformed Pennzane (Shell Global Solutions) X-2000 by more than an order of magnitude. Lubricant evaporation played a key role in these high temperature results. At 75 C, the order was reversed with both Pennzane X-1000 and X-2000 outperforming Fomblin Z25 by more than an order of magnitude. Most Pennzane tests were suspended without failure. The primary failure mechanism in these lower temperature tests was lubricant consumption in the tribocontacts.

Braza, Joseph↗

Simple Formulas and Results for Buckling-Resistance and Stiffness Design of Compression-Loaded Laminated-Composite Cylinders

Simple formulas for the buckling stress of homogeneous, specially orthotropic, laminated-composite cylinders are presented. The formulas are obtained by using nondimensional parameters and equations that facilitate general validation, and are validated against the exact solution for a wide range of cylinder geometries and laminate constructions. Results are presented that establish the ranges of the nondimensional parameters and coefficients used. General results, given in terms of the nondimensional parameters, are presented that encompass a wide range of geometries and laminate constructions. These general results also illustrate a wide spectrum of behavioral trends. Design-oriented results are also presented that provide a simple, clear indication of laminate composition on critical stress, critical strain, and axial stiffness. An example is provided to demonstrate the application of these results to thin-walled column designs.

Nemeth, Michael P.↗

Shearography NDE of NASA COPV

1. 21 Composite Over-wrapped Pressure Vessels (COPV) consisting of Kevlar Space Shuttle Fleet Leaders and Graphite COPV were inspected at NASA WSTF, NM from Sept. 12 through Sept 16. 2. The inspection technique was Pressurization Shearography, tests designed to image composite material damage, degradation or design flaws leading to stress concentrations in the axial or hoop strain load path. 3. The defect types detected consisted of the following: a) Intentional impact damage with known energy. b) Un-intentional impact damage. c) Manufacturing defects. 4. COPV design features leading to strain concentrations detected include: a) Strain concentrations at bosses due to fiber closure pattern. b) Strain concentrations in body of COPV due to fiber wrap pattern. c) Strain concentrations at equator due to liner weld/fiber lay-up.

Newman, John W.↗

Flat plate puncture test convergence study.

The ASME Task Group on Computational Mechanics for Explicit Dynamics is investigating the types of finite element models needed to accurately solve various problems that occur frequently in cask design. One type of problem is the 1-meter impact onto a puncture spike. The work described in this paper considers this impact for a relatively thin-walled shell, represented as a flat plate. The effects of mesh refinement, friction coefficient, material models, and finite element code will be discussed. The actual punch, as defined in the transport regulations, is 15 cm in diameter with a corner radius of no more than 6 mm. The punch used in the initial part of this study has the same diameter, but has a corner radius of 25 mm. This more rounded punch was used to allow convergence of the solution with a coarser mesh. A future task will be to investigate the effect of having a punch with a smaller corner radius. The 25-cm thick type 304 stainless steel plate that represents the cask wall is 1 meter in diameter and has added mass on the edge to represent the remainder of the cask. The amount of added mass to use was calculated using Nelm's equation, an empirically derived relationship between weight, wall thickness, and ultimate strength that prevents punch through. The outer edge of the plate is restrained so that it can only move in the direction parallel to the axis of the punch. Results that are compared include the deflection at the edge of the plate, the deflection at the center of the plate, the plastic strains at radius r=50 cm and r=100 cm , and qualitatively, the distribution of plastic strains. The strains of interest are those on the surface of the plate, not the integration point strains. Because cask designers are using analyses of this type to determine if shell will puncture, a failure theory, including the effect of the tri-axial nature of the stress state, is also discussed. The results of this study will help to determine what constitutes an adequate finite element model for analyzing the puncture hypothetical accident.

36 MATERIALS SCIENCE↗

Numerical Simulations of the Supercritical Carbon Dioxide Round Turbulent Jet

We explore the fundamental connection between properties of a supercritical fluid and observed behavior of the flow by comparing simulations of a supercritical carbon dioxide (sCO2) round jet to canonical simulations using an ideal gas model. sCO2 has desirable behavior that can improve power density compared to traditional fluids for applications involving closed-cycle gas turbines, heat transmission, and hydraulic fracturing while facilitating carbon sequestration. While literature exists focusing on the prospects of sCO2 in various industries, the quantities of interest studied tend to be application specific whereas our investigation generalizes across multiple applications. The Soave-Redlich-Kwong equation of state is utilized to close our system of equations; we use a second order finite volume method in conjunction with adaptive mesh refinement as implemented in PeleC. The jet is at p=10 MPa and T=600 K in order to maintain a single-phase fluid. Quantities of interest for this study include the mean axial velocity and Reynolds stresses.

97 MATHEMATICS AND COMPUTING↗

Overview of the experiments performed with Russian claddings at MTA EK

The mechanical and corrosion behavior of the Russian-type zirconium cladding alloy E110, predominantly used in VVERs, has been investigated for many decades. The recent commercialization of a new alloy E110G, produced on a sponge zirconium basis, gave the opportunity to compare the mechanical properties of the old E110 and the new E110G fuel claddings. The mechanical experiments performed with samples from both claddings in MTA EK including axial and tangential (ring) tensile tests at 20, 150 and 300 Celsius degrees. The chosen geometries for the tests were modelled using finite element method. Due to the anisotropy of the cladding tubes the axial yield strength was 6% higher than the tangential. The yield strength of the E110G alloy was 12% higher than for the E110 claddings at ambient temperature, but this difference decreased to 5% at 300 C. degrees. Some samples underwent chemical or thermal treatments and the effects of these were evaluated. These treatments were slight oxidation in steam at 800 C. degrees up to 3 ECR%, hydridation at 600 C. degrees up to 400 ppm, and heat treatment in argon atmosphere at temperatures between 600 and 1000 C. degrees. The results confirm that the heat treatment has more significant effect on the yield strength of the claddings than the chemical treatments. While the yield strength of the oxidized samples was slightly higher, when combined with the data from the heat treatment at 800 C. degrees, the oxidation itself seems to have lowered the yield strength as the thickness of the metal decreased. The hydridation of the cladding samples did not change the yield strength and the samples remained ductile even at room temperature. The thermo-mechanical creep of the two cladding alloys was also investigated. Biaxial and uniaxial creep experiments were performed with 100 mm long cladding tubes. In the biaxial test, samples of both alloys were pressurized with argon to 5, 7.5 and 10 MPa at 500 C. degrees and the test lasted till the depressurization of the tubes. The uniaxial creep was measured at 300 and 500 C. degrees in the axial direction and constant stress was applied using weights. This stress was 14.8 and 27.7 MPa at 300 C. degrees and 3.7 and 6.5 MPa at 500 C. degrees. The elongation and diametrical change of the samples were measured using different methods. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Structure and decay characteristics of turbulence in the near- and far-wake of a moderately loaded compressor rotor-blade

The wake of a turbomachinery rotor-blade is turbulent, highly three-dimensional, and nonisotropic with appreciable curvature in the trailing-edge and near-wake regions. The characteristics of the turbulence vary considerably with radius, blade loading, free-stream turbulence, Reynolds number, and the rotor-blade geometry. This paper is concerned with the turbulence properties of a moderately loaded compressor blade, particularly near the blade trailing-edge. The tangential variation of the axial, tangential and radial intensities and stresses across the wake, as well as their decay characteristics were measured with a tri-axial hot-wire probe in the rotor frame of reference. The decay of intensities and stresses were found to be very rapid in the trailing-edge and near-wake regions and slow in the far-wake region. The effects of inlet-guide-vane and the hub-wall boundary layers on the rotor wake turbulence spectra are also discussed. Similarity rules for the three components of intensity are also derived and presented in this paper.

Ravindranath, A.↗