Results for “3D characterization” — Page 17

NASA NTRS2018

2.5/3D Daisy Chain Reliability Evaluation

The objective of this task is to evaluate thermal cycle behavior of advanced 2.5/3D electronics — commercial-off the-shelf (COTS) —packages of different configurations assembled onto printed circuit boards (PCBs). Three key approaches were considered for evaluation. The first approach focused on the through-mold via (TMV™) technology at assembly level. The second approach focused on evaluation of 2.5D (also known as, System in Package (SiP)) in fine pitch ball grid array (FPGA). The third approach focused on evaluation of through-silicone-via (TSV) technologies. This report presents the test results for TMV™ and SiP packaging technologies and reliability, and it also provides lessons learned on quality assurance methods. Specifically, the report presents the test matrix for various 3D TMV™ packaging assembly configurations and reliability characterizations performed under two accelerated thermal cycling (ATC) and accelerated thermal shock cycling (ATSC) conditions. The ATC and ATSC were performed in the range of –55°C to 125°C and –100°C to 100°C, respectively. The report also includes assembly of a SiP— a 60-mm fine-pitch ball-grid array (FPGA) interposer with an IC at the center and six chip-scale package (CSP) daisy chains at the periphery—with package assembly characterizations. After assembly, the daisy chains were subjected to ATCs in the range of –40°C to 125°C for reliability evaluation. Finally, for both TMV™ and SiP packaging configurations, characterizations results by X-ray, optical imaging, and daisy-chain resistance evaluations were also presented.

Ghaffarian, Reza↗

NASA NTRS2022

Validation and Interpretation of a Three-dimensional Configuration of a Magnetic Cloud Flux Rope

One strong magnetic cloud (MC)with a magnetic field magnitude reaching∼40 nT at 1 au during 2012 June16–17 is examined in association with a preexisting magnetic flux rope (MFR)identified on the Sun. The MC is characterized by a quasi-three-dimensional(3D) flux rope model based on in situ measurements from the Wind spacecraft. The contents of the magnetic flux and other parameters are quantified. In addition, a correlative study with the corresponding measurements of the same structure crossed by the Venus Express (VEX)spacecraft at a heliocentric distance of 0.7 au and with an angular separation of∼6°in longitude is performed to validate the MC modeling results. The spatial variation between the Wind and VEX magnetic field measurements is attributed to the3D configuration of the structure appearing as a knotted bundle of flux. A comparison of the magnetic flux contents between the MC and the preexisting MFR on the Sun indicates that the 3D reconnection process accompanying anM1.9flare may correspond to the magnetic reconnection between the field lines of the preexisting MFR rooted in the opposite polarity foot points. Such a process reduces the amount of the axial magnetic flux in the erupted flux rope, by approximately 50%, in this case.

Qiang Hu↗

NASA NTRS2007

3D Radiative Aspects of the Increased Aerosol Optical Depth Near Clouds

To characterize aerosol-cloud interactions it is important to correctly retrieve aerosol optical depth in the vicinity of clouds. It is well reported in the literature that aerosol optical depth increases with cloud cover. Part of the increase comes from real physics as humidification; another part, however, comes from 3D cloud effects in the remote sensing retrievals. In many cases it is hard to say whether the retrieved increased values of aerosol optical depth are remote sensing artifacts or real. In the presentation, we will discuss how the 3D cloud affects can be mitigated. We will demonstrate a simple model that can assess the enhanced illumination of cloud-free columns in the vicinity of clouds. This model is based on the assumption that the enhancement in the cloud-free column radiance comes from the enhanced Rayleigh scattering due to presence of surrounding clouds. A stochastic cloud model of broken cloudiness is used to simulate the upward flux.

Marshak, Alexander↗

DOE OSTI2023

Towards Three-Dimensional Neutron Imaging with Light-field Technology

A broad range of applications in nuclear safeguards and security can benefit from compact, fast neutron imagers with large angular acceptance. However, accurate 3D multi-vertex reconstruction in a monolithic detector remains a significant barrier to realization. Current approaches, such as the centroiding approach and the use of shadow masks, have not yet resulted in a successful demonstration in a light-starved environment. This project explored the use of cutting-edge technology—a light field camera—which inherently preserves both the spatial and directional information of incident light. Such technology can, in principle, resolve multi-vertex events and offer accurate position reconstruction in 3D with relatively simple readout electronics. Since the project's inception in May 2023, we have built an experimental setup to calibrate and characterize a commercial light-field camera (Lytro Illum). We assessed its 3D event reconstruction capability in a relatively low-light intensity environment by analyzing the cross-correlation of a series of 2D images of a characterized tunable light source taken at various distances. A sub-cm resolution, lower than typical neutron interaction separations in a compact scintillator volume, was observed with the LED light source, suggesting the promising capability of its nominal optics design to provide the adequate resolution required for a compact monolithic neutron directional detector. However, using a light-field-based readout for a neutron camera requires incorporating an ultra-low-noise light sensor, which is beyond the scope of this project. We also initiated the development of a 3D light-field-based reconstruction algorithm tailored to sparse scenes, as expected from particle interactions in a scintillator medium. Additionally, we demonstrated the capability of the algorithm to replicate the ground truth. Finally, we began the development of a neutron directional detector simulation to determine the performance criteria for light-field-based reconstruction that allows for good neutron directional reconstruction. This Feasibility Study has led to a successful follow-up project under the DNN R&D innovation portfolio starting May 2024.

42 ENGINEERING↗

NASA NTRSDate not supplied

Quantitative 3D Textural and Petrofabric Analysis of the Northwest Africa 10645 Nakhlite Using X-Ray Computed Tomography

Martian meteorites are currently the only samples available from Mars to study and are critical for elucidating variability in martian igneous processes over time [e.g., 1]. Quantifying igneous textures and fabrics can help us understand how rocks are formed and emplaced [e.g., 2]. These features are innately three dimensional (3D) and are often strongly heterogeneous in cumulate rocks, like the nakhlites and poikilitic shergottites [2–3], where there can be substantial textural variations between and within individual samples. However, most quantitative textural and fabric analyses on these samples have been limited to two dimensions through measurements made on polished petrographic thin sections. Thus, 3D petrographic measurements are imperative for both representative sample characterization and accurately interpreting magmatic processes. The emplacement of martian meteorites at or near the surface of Mars (i.e., extrusive or intrusive, respectively) remains enigmatic due to the innate lack of geologic context [e.g., 1], but conducting 3D quantitative textural and fabric analyses can help elucidate emplacement mechanisms and settings on Mars.

S. Ramsey↗

DOE OSTI2024

Electrostatic Dissipation in 3D-Printable Silicone

Here, in this report, we describe the incorporation of single-walled carbon nanotubes (CNTs) into 3D printable siloxane elastomers for electrostatic dissipation. The composite was characterized, focusing on how rheological and mechanical properties of the siloxane are affected at various CNT loading levels. Electrical properties were also characterized to develop materials with effective electrostatic dissipation. We demonstrate that low loadings (<1 wt %) of CNTs can be sufficiently dispersed into silicone resins that can be 3D printed, and the resulting material shows a significant improvement in electrostatic dissipation through the reduction in electrical resistivity with minimal effect on its mechanical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Open Source Visualization and Analysis Platform for 3D Reconstructions of Materials by Transmission Electron Microscopy

Three-dimensional characterization of materials at the nano- and meso-scale has become possible with transmission and scanning transmission electron microscopes (S/TEM). Its importance has extended to a wide class of nanomaterials such as hydrogen fuel cells, solar cells, industrial catalysts, new battery materials and semiconductor devices, as well as spanning high-tech industry, universities, and national labs. While capable instrumentation is abundant, this rapidly expanding demand for high-resolution tomography is bottlenecked by software that is instead tailored for lower-dose, biological applications and not optimized for higher-resolution materials applications. Existing tomography fails to utilize the chemical information provided by S/TEM spectrometers. To address this problem, this project delivered a scalable, fully functional, freely-distributable, open Source materials tomography package with a modern user interface that enables automated acquisition, alignment, and real-time reconstruction of raw tomography data, and provides advanced segmentation, three-dimensional chemical visualization and analysis optimized for materials applications. It has established an extendable framework capable of automation for high-throughput for the tomography of materials from data acquisition to visualization. Phase I and II delivered a full-featured, cross-platform, clean and integrated application for S/TEM materials tomography. It can read projection data from the microscope, with graphical tools for alignment of data, tomographic reconstruction, segmentation, and visualization of the reconstructed 3D volume. The entire pipeline can be saved to an XML state file, enabling fully reproducible data processing and analysis with a full Python environment for the development of custom algorithms, processing, and analysis requirements. Phase IIB extended the application to provide real-time tomographic reconstruction, "live updates" as data is processed, analysis of big data, and multi-channel tomography. Here, quantitative assessment of nanomaterials can occur as data is being recorded on a 3D visualization platform that accommodates additional information from multiple channels. We provide unmatched high-throughput tomography, where the complete tomographic pipeline from measurement to 3D visualization can occur rapidly. The project was extended to offer capabilities for micro-CT, X-ray, neutron, focused ion beam, atomic electron tomography and atom probe tomography. With over 600 transmission electron microscopes worldwide and approximately 50 coming online each year, the demand and impact of an open-source tomography tool is large. Significant opportunities exist in high-tech industry, universities, and national labs to enable or enhance three-dimensional imaging at the nanoscale and bring automated high-throughput approaches that will accelerate progress in materials characterization and metrology. The project supports a service based business model by enabling lab-specific acquisition and processing customization and integration-support and development that will be provided into Phase III and beyond.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Three-dimensional unstructured grid generation via incremental insertion and local optimization

Algorithms for the generation of 3D unstructured surface and volume grids are discussed. These algorithms are based on incremental insertion and local optimization. The present algorithms are very general and permit local grid optimization based on various measures of grid quality. This is very important; unlike the 2D Delaunay triangulation, the 3D Delaunay triangulation appears not to have a lexicographic characterization of angularity. (The Delaunay triangulation is known to minimize that maximum containment sphere, but unfortunately this is not true lexicographically). Consequently, Delaunay triangulations in three-space can result in poorly shaped tetrahedral elements. Using the present algorithms, 3D meshes can be constructed which optimize a certain angle measure, albeit locally. We also discuss the combinatorial aspects of the algorithm as well as implementational details.

Barth, Timothy J.↗

NASA NTRS2024

Development of Weighout Process and Evaluations for Underwater Partial Gravity EVA Simulations

For the upcoming Artemis lunar missions, astronauts will needto train in a spacesuit where partial gravity can be simulated such as NASA Neutral Buoyancy Lab (NBL). At the NBL, dive weights and foam can be added around the spacesuit to attaina satisfactory center of buoyancy (CB) and center of gravity (CG) location to simulate the lunar gravity (1/6thG) effects. If CG and CB are not co-located properly, incorrect righting moments can be introduced, and both simulation quality and EVA task performance can be impaired. Based on the findings from the initial testingusing xEMU spacesuits, it was observed that the weigh-out method (i.e., determination of the weights and foam quantities and position) needed further development to improve the simulation quality, especially for the subjects who experienced excessive instability. This paper aims to present the on-going effort to improve the weigh-out process for enabling NBL lunar EVA simulations. For this effort, a human-suit model was created to use suit CAD and 3D human body scansto estimate both CB and CG location for each suited subject. NBL weigh-out testing was performed to characterize the effects of CG and CB positioning, in which the 3D human-suit model was used to determine optimal weigh-out combinations of weights and foam. Postural, balance, and subjective feedback were gathered for each weigh-out configuration. The results indicated that, as the CB was shifted higher and the CB and CG located closer to each other, the subject tended to be more stable and their EVA performance improved. A high CB location was then prioritized across 4 additional subjects in both small and large size spacesuits. When compared to the initial xEMU test series, improved performance was observed across all subjects as the CB moved higher and aligned closer to the system CG.

Seyed Pouyan Sabahi↗

DOE OSTI2021

Dielectric metasurfaces made from vertically oriented nanoresonators

Dielectric metasurfaces control optical wavefronts via nanoscale resonators laid out across a surface. However, most metasurfaces are, by design, planar. In this work, we demonstrate the ability to fabricate dielectric metasurfaces with vertically oriented dielectric resonators using membrane projection lithography. We first numerically characterize the resonant modes of an array of vertically oriented germanium ellipses with no substrate and identify a narrowband region where the resonators satisfy the first Kerker condition. We then fabricate seven metasurfaces by depositing germanium ellipses onto walls of a 3D micrometer-sized silicon nitride photonic scaffold and characterize their transmission. We find that signatures of the multipolar modes seen in the unsupported array persist in the supported array, but the overall behavior is more complicated due to the scaffold. Further, we show that for a conceptual metasurface containing two coupled, vertically oriented ellipses, the ellipses can generate a sharp resonance with a quality factor of 240.

Gennaro, Sylvain D. (ORCID:0000000222090831)↗

NASA NTRS2016

Additive Manufacturing and Characterization of Polylactic Acid (PLA) Composites Containing Metal Reinforcements

Additive manufacturing of polymeric systems using 3D printing has become quite popular recently due to rapid growth and availability of low cost and open source 3D printers. Two widely used 3D printing filaments are based on polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) systems. PLA is much more environmentally friendly in comparison to ABS since it is made from renewable resources such as corn, sugarcane, and other starches as precursors. Recently, polylactic acid-based metal powder containing composite filaments have emerged which could be utilized for multifunctional applications. The composite filaments have higher density than pure PLA, and the majority of the materials volume is made up of polylactic acid. In order to utilize functionalities of composite filaments, printing behavior and properties of 3-D printed composites need to be characterized and compared with the pure PLA materials. In this study, pure PLA and composite specimens with different metallic reinforcements (Copper, Bronze, Tungsten, Iron, etc) were 3D printed at various layer heights and resulting microstructures and properties were characterized. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) behavior of filaments with different reinforcements were studied. The microscopy results show an increase in porosity between 3-D printed regular PLA and the metal composite PLA samples, which could produce weaker mechanical properties in the metal composite materials. Tensile strength and fracture toughness behavior of specimens as a function of print layer height will be presented.

brass↗

NASA NTRSDate not supplied

Challenges in Scaling Analysis from Coupons to Elements in 3D Woven Composites for a Launch Vehicle End-Ring Structure

The limitations of structural design with 3D woven composites based on homogenized material models characterized using coupon test data, representative unit cell analysis, or a combination of the two are discussed in the context of a space launch system (SLS)-scale end ring. Selected building block test configurations at the coupon, element, and subcomponent scales are described in detail. Highly instrumented tests and X-ray computed tomography inspections are used to characterize the structural behavior and associated damage progression with increasing load. It is shown that a single homogenized material constitutive relationship, applied at coupon and element scale, is not sufficient to model the structural response observed in both tests. In fact, substantially different stress-strain laws are required to predict the response of the coupon and element scale specimens, despite similar loading conditions. A model with discrete representation of the binder tows and cohesive interfaces to model matrix cracking shows much better agreement with the test data at the two length scales. Thus, evidence is provided showing that predictive structural analysis of 3D woven composites requires discrete representation of the tows, matrix cracking morphology, and their interactions in the structural configuration. With accurate knowledge of the element scale behavior, engineering approximations readily enable analysis scale-up to the subcomponent level.

Andrew C Bergan↗

NASA NTRS2024

Development of Weigh-out Process and Evaluations for Underwater Partial Gravity Simulations

For the upcoming Artemis lunar missions, astronauts will need to train in a spacesuit where partial gravity can be simulated such as the NASA Neutral Buoyancy Lab (NBL). At the NBL, dive weights and foam can be added around the spacesuit to attain a satisfactory center of buoyancy (CB) and center of gravity (CG) location to simulate the lunar gravity (1/6thG) effects. If CG and CB are not co-located properly, incorrect righting moments can be introduced, and both simulation quality and EVA task performance can be impaired. Based on the findings from the initial testing using xEMU spacesuits, it was observed that the weigh-out method (i.e., determination of the weights and foam quantities and position) needed further development to improve the simulation quality, especially for the subjects who experienced excessive instability. This paper aims to present the on-going effort to improve the weigh-out process for enabling NBL lunar EVA simulations. For this effort, a human-suit model was created to use suit CAD and 3D human body scans to estimate both CB and CG location for each suited subject. NBL weigh-out testing was performed to characterize the effects of CG and CB positioning, in which the 3D human-suit model was used to determine optimal weigh-out combinations of weights and foam. Postural, balance, and subjective feedback were gathered for each weigh-out configuration. The results indicated that, as the CB was shifted higher and the CB and CG located closer to each other, the subject tended to be more stable and their EVA performance improved. A high CB location was then prioritized across 4 additional subjects in both small and large size spacesuits. When compared to the initial xEMU test series, improved performance was observed across all subjects as the CB moved higher and aligned closer to the system CG.

Pouyan Sabahi↗

NASA NTRS2024

Development of Weigh-out Process and Evaluations for Underwater Partial Gravity Simulations

For the upcoming Artemis lunar missions, astronauts will need to train in a spacesuit where partial gravity can be simulated such as the NASA Neutral Buoyancy Lab (NBL). At the NBL, dive weights and foam can be added around the spacesuit to attain a satisfactory center of buoyancy (CB) and center of gravity (CG) location to simulate the lunar gravity (1/6thG) effects. If CG and CB are not co-located properly, incorrect righting moments can be introduced, and both simulation quality and EVA task performance can be impaired. Based on the findings from the initial testing using xEMU spacesuits, it was observed that the weigh-out method (i.e., determination of the weights and foam quantities and position) needed further development to improve the simulation quality, especially for the subjects who experienced excessive instability. This paper aims to present the on-going effort to improve the weigh-out process for enabling NBL lunar EVA simulations. For this effort, a human-suit model was created to use suit CAD and 3D human body scans to estimate both CB and CG location for each suited subject. NBL weigh-out testing was performed to characterize the effects of CG and CB positioning, in which the 3D human-suit model was used to determine optimal weigh-out combinations of weights and foam. Postural, balance, and subjective feedback were gathered for each weigh-out configuration. The results indicated that, as the CB was shifted higher and the CB and CG located closer to each other, the subject tended to be more stable and their EVA performance improved. A high CB location was then prioritized across 4 additional subjects in both small and large size spacesuits. When compared to the initial xEMU test series, improved performance was observed across all subjects as the CB moved higher and aligned closer to the system CG.

Pouyan Sabahi↗

NASA NTRSDate not supplied

Development of Weigh-Out Process and Evaluations for Underwater Partial Gravity Simulations

For the upcoming Artemis lunar missions, astronauts will need to train in a spacesuit where partial gravity can be simulated such as the NASA Neutral Buoyancy Lab (NBL). At the NBL, dive weights and foam can be added around the spacesuit to attain a satisfactory center of buoyancy (CB) and center of gravity (CG) location to simulate the lunar gravity (1/6thG) effects. If CG and CB are not co-located properly, incorrect righting moments can be introduced, and both simulation quality and EVA task performance can be impaired. Based on the findings from the initial testing using xEMU spacesuits, it was observed that the weigh-out method (i.e., determination of the weights and foam quantities and position) needed further development to improve the simulation quality, especially for the subjects who experienced excessive instability. This paper aims to present the on-going effort to improve the weigh-out process for enabling NBL lunar EVA simulations. For this effort, a human-suit model was created to use suit CAD and 3D human body scans to estimate both CB and CG location for each suited subject. NBL weigh-out testing was performed to characterize the effects of CG and CB positioning, in which the 3D human-suit model was used to determine optimal weigh-out combinations of weights and foam. Postural, balance, and subjective feedback were gathered for each weigh-out configuration. The results indicated that, as the CB was shifted higher and the CB and CG located closer to each other, the subject tended to be more stable and their EVA performance improved. A high CB location was then prioritized across 4 additional subjects in both small and large size spacesuits. When compared to the initial xEMU test series, improved performance was observed across all subjects as the CB moved higher and aligned closer to the system CG.

Pouyan Sabahi↗

DOE OSTI2024

Use of a Lignin-Based Admixture for Tailoring the Rheological Properties of Mortars for 3D Printing: Preprint

Efforts toward decarbonizing construction materials and industrial processes related to cement and concrete can be aided via multifaceted approaches that target alternative admixtures as well as precision control of fabrication. Chemical admixtures for water reduction have played a crucial role in the development of advanced concrete mixtures. Newer biomass processing techniques developed for aviation fuel production from corn stover biomass produce a more reactive lignin byproduct that is suitable for chemical modifications to mimic the properties of polycarboxylate ether admixtures with a smaller carbon footprint. The present study examines the use of lignin-based water-reducing admixture in cement pastes and mortar mixtures for 3D printing. The experimental program explores the use of different dosages of lignin-based admixture to produce 3D-printed samples with appropriate extrudability and buildability. The rheological characterization was performed to determine the flow curve of various mixtures. Finally, the heat of hydration of cement pastes was monitored via isothermal calorimetry to assess the impact of lignin-based admixtures on the hydration process of cement. The results of this study indicate that the use of biomass by-products, such as lignin-based admixtures have great potential to effectively control the fresh-state properties of cement-based materials.

bio-based admixtures↗

DOE OSTI2020

Three-dimensional imaging of mitochondrial cristae complexity using cryo-soft X-ray tomography

Mitochondria are dynamic organelles that change morphology to adapt to cellular energetic demands under both physiological and stress conditions. Cardiomyopathies and neuronal disorders are associated with structure-related dysfunction in mitochondria, but three-dimensional characterizations of the organelles are still lacking. In this study, we combined high-resolution imaging and 3D electron density information provided by cryo-soft X-ray tomography to characterize mitochondria cristae morphology isolated from murine. Using the linear attenuation coefficient, the mitochondria were identified (0.247 ± 0.04 µm -1 ) presenting average dimensions of 0.90 ± 0.20 µm in length and 0.63 ± 0.12 µm in width. The internal mitochondria structure was successfully identified by reaching up the limit of spatial resolution of 35 nm. The internal mitochondrial membranes invagination (cristae) complexity was calculated by the mitochondrial complexity index (MCI) providing quantitative and morphological information of mitochondria larger than 0.90 mm in length. The segmentation to visualize the cristae invaginations into the mitochondrial matrix was possible in mitochondria with MCI ≥ 7. Altogether, we demonstrated that the MCI is a valuable quantitative morphological parameter to evaluate cristae modelling and can be applied to compare healthy and disease state associated to mitochondria morphology.

3-D reconstruction↗

NASA NTRS2012

Characterization a single-lens based stereoscopic camera

Traditional stereoscopic vision (3D) is achieved through use of two cameras arranged to emulate human eyes. While this method works on large scale projects, it becomes impractical to use on small scale designs, such as surgical endoscopes, in which the operational area doesn’t allow the immensity of dual camera systems. This project is focused on developing a stereoscopic endoscope using a single camera and Conjugated Multiple-Bandpass Filters (CMBF) to create 3D images. Each filter is designed to allow only a distinct spectrum of light to pass through. The stereoscopic image can be obtained by using filters that reflect and reject wavelengths, complementary to one another. A major concern in all stereovision is crosstalk, defined as the light from one eye image that is present in the other eye image. This incomplete isolation causes deterioration of the 3D image. In our system, the crosstalk comes from imperfect filters. The filter spectrums overlap at certain wavelengths, causing a dim outline of the right eye image to leak into the left eye image and vice versa, a phenomenon known as ghosting. Knowledge of the extent of this phenomenon is critical to creating sustainable, effective stereovision.

Fritz, Eric↗