Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Direct Ink Write 3D Printing of Fully Dense and Functionally Graded Liquid Metal Elastomer Foams

Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human-machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.

Spencer Pak↗
NASA NTRS2017

Design and Testing of a Hall Effect Thruster with 3D Printed Channel and Propellant Distributor

The UAH-78AM is a low-power Hall effect thruster developed at the University of Alabama in Huntsville with channel walls and a propellant distributor manufactured using 3D printing. The goal of this project is to assess the feasibility of using unconventional materials to produce a low-cost functioning Hall effect thruster and consider how additive manufacturing can expand the design space and provide other benefits. A version of the thruster was tested at NASA Glenn Research Center to obtain performance metrics and to validate the ability of the thruster to produce thrust and sustain a discharge. An overview of the thruster design and transient performance measurements are presented here. Measured thrust ranged from 17.2 millinewtons to 30.4 millinewtons over a discharge power of 280 watts to 520 watts with an anode I (sub SP)(Specific Impulse) range of 870 seconds to 1450 seconds. Temperature limitations of materials used for the channel walls and propellant distributor limit the ability to run the thruster at thermal steady-state.

Hall thrusters↗
DOE OSTI2020

Tunable structural color of bottlebrush block copolymers through direct-write 3D printing from solution

Additive manufacturing of functional materials is limited by control of microstructure and assembly at the nanoscale. In this work, we integrate nonequilibrium self-assembly with direct-write three-dimensional (3D) printing to prepare bottlebrush block copolymer (BBCP) photonic crystals (PCs) with tunable structure color. After varying deposition conditions during printing of a single ink solution, peak reflected wavelength for BBCP PCs span a range of 403 to 626 nm (blue to red), corresponding to an estimated change in d-spacing of >70 nm (Bragg- Snell equation). Physical characterization confirms that these vivid optical effects are underpinned by tuning of lamellar domain spacing, which we attribute to modulation of polymer conformation. Using in situ optical microscopy and solvent-vapor annealing, we identify kinetic trapping of metastable microstructures during printing as the mechanism for domain size control. More generally, we present a robust processing scheme with potential for on-the-fly property tuning of a variety of functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

W-ZrC composites prepared by reactive melt infiltration of Zr 2 Cu alloy into binder jet 3D printed WC preforms

W-ZrC composites were successfully prepared by reactive melt infiltration (RMI) of stoichiometric and excess amounts of Zr 2 Cu into sintered and un-sintered WC preforms made from binder jet 3D printing. The focus of this work was to study the conversion of reactant powders and liquid infiltrant with varying preform density and infiltrant amount by controlling the processing time to reach high conversion yield while understanding the phase composition, microstructure, and hardness. To investigate the effect of time, the reactive melt infiltration was conducted at 1400 °C for 2, 4 and 8 h in a furnace with 96% Ar - 4% H2 gas atmosphere. The increase in reaction time from 2 to 8 h increased the W and W 2 C phase contents and decreased the ZrC phase content when using sintered WC preforms. Samples prepared from un-sintered WC preforms exhibited improved reactive melt infiltration compared to sintered samples, and there was no detectable W 2 C phase and nearly full consumption of WC. Similar to sintered WC samples, the content of W and ZrC phases increased with the increase in time from 2 to 8 h. The interfaces and phases at reaction interfaces were investigated using electron diffraction analysis and S/TEM-EDS to understand material stability; the phases were identified and consistent with XRD analysis. Additionally, there was no Cu present at the interfaces. Increasing the amount of infiltrant led to better reactive melt infiltration. In general, the hardness increased with reaction time and the highest Vickers hardness was found in the W-ZrC sample formed from sintered WC reacted with excess Zr 2 Cu. Finally, this research addresses the critical comparison of sintering and RMI time and shows that by using un-sintered samples for 8 h we are able to achieve W-ZrC composites with fewer undesired phases.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of 3D Printing Techniques for Solid-State Lithium Batteries: Energy Storage Internship (Final Report)

The goal of this internship was to develop a solid polymer electrolyte with a suitable ionic conductivity and mechanical properties and integrate it with 3D printed cathode for solid state lithium batteries. While liquid electrolytes will have much higher conductivities and therefore higher power densities than solid electrolytes, batteries with such electrolytes suffer from extreme dendritic growth, short-circuiting, and general failure. Typically, batteries prevent this by including a solid yet porous separator somewhere between the anode and cathode to suppress dendritic growth. Solid polymer electrolyte acts as the conductive medium between electrodes as well as the separator that prevents failure from short-circuiting. The specific system explored is a vinyl ethylene carbonate (VEC) and polyethylene glycol diacrylate (PEGDA) mixed polymer solution using both 2,2’-azobis(2-methylpropionitrile) (AIBN) and Irgacure 819, respectively as thermal and photo- initiators. Electrochemical and rheological techniques were used to determine the optimal polymer solution and curing conditions. Through this research, multiple new pathways of exploration have been determined to create a usable solid polymer electrolyte through a combination of varying cure intensities and initiator concentrations.

25 ENERGY STORAGE↗
NASA NTRS2018

Summary Report on Phase I and Phase II Results From the 3D Printing in Zero-G Technology Demonstration Mission

In-space manufacturing seeks to develop the processes, skill sets, and certification architecture needed to provide a rapid response manufacturing capability on long-duration exploration missions. The first 3D printer on the Space Station was developed by Made in Space, Inc. and completed two rounds of operation on orbit as part of the 3D Printing in Zero-G Technology Demonstration Mission. This Technical Publication provides a comprehensive overview of the technical objections of the mission, the two phases of hardware operation conducted on orbit, and the subsequent detailed analysis of specimens produced. No engineering significant evidence of microgravity effects on material outcomes was noted. This technology demonstration mission represents the first step in developing a suite of manufacturing capabilities to meet future mission needs.

Prater, T. J.↗
DOE OSTI2022

Coal polymer composites prepared by fused deposition modeling (FDM) 3D printing

Coal is a vital energy resource worldwide, but pollutants and greenhouse gases from its combustion cause environmental problems. To explore the non-combustion approach to use and valorize coal, anthracite and lignite were blended with polyamide 12 (PA 12) through FDM printing in this work and compared in the composites. By adding lignite, Young’s modulus improved with increasing loading to 50 wt% while tensile strength leveled off among the composites, compared to that of PA 12. By contrast, the addition of anthracite decreased the tensile performance at all loadings. Rheology tests and morphology analyses suggested that the interactions between fillers (anthracite and lignite) and PA 12 may cause differences in tensile properties. In addition, the printed lignite composites showed improved thermal conductivity (~ twofold), indicating lignite demonstrates the potential to build functional composites. This work provides a strategy to use lignite in composites by 3D printing for value-added products and reduces the demand for petroleum-based polymers. Overall, our approach diverts lignite from combustion processes and alleviates the negative impact of lignite use on the environment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Experimental and Theoretical Evaluation of Feed Flow Collar Design For 3D Printed Shell-Fed Hollow Fiber Membrane Modules

This presentation was given at the 2024 AIChE Annual Meeting, San Diego, CA, October 27-31, 2024. The presentation details a method for the efficient fabrication and approximation of membrane performance, developed utilizing 3D printed experimental modules for small hollow fiber modules containing multiple fibers for experimental and simulation comparisons.

Tran, Thien↗
DOE OSTI2022

On the Economic, Environmental, and Sustainability Aspects of 3D Printing toward a Cyclic Economy

Industrial manufacturing of materials may achieve, not only increased profit, but also reduced waste generation, energy consumption, and global greenhouse gas emissions through additive manufacturing (AM). This chapter puts into perspectives the ideas and benefits of using 3D printing technology in the manufacture of durable and sustainable materials, enabling high-value reuse toward the promotion of a better cyclic economy.

Caldona, Eugene↗
DOE OSTI2024

Advanced Design and 3D Printing Strategies With Alginate‐Nanoclay Nanocomposites: From Microstructure to Bioprinting

Nanocomposites made from alginate and nanoclay are extensively applied for diverse biomedical applications. However, the lack of a clear understanding of the interactions between alginate and nanoclay makes it difficult to rationally design the nanocomposites for different material extrusion-based 3D bioprinting strategies. Here, a combined analytical model is proposed to accurately predict the interaction mechanisms between alginate and nanoclay through small-angle neutron scattering. These mechanisms are summarized into a phase diagram that can guide the design of alginate-nanoclay nanocomposites for different bioprinting applications. The rheological properties of various nanocomposites are measured to validate the proposed interaction mechanisms at the macroscale. Accordingly, three representative extrusion-based bioprinting strategies are linked with the nanocomposite design and applied to freeform fabricate complex structures. In conclusion, a roadmap is summarized to bridge the gap between biomaterial design and bioprinting processes, enabling the rapid and rational selection of biomaterial formula based on available 3D printing methods, and vice versa.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Initial Assessment of 3D-Printed Molybdenum Lattices as a Substrate for Liquid Metal Plasma-Facing Components

Many liquid metal plasma-facing component concepts for fusion reactors require a capillary porous material to wick the liquid metal to the surface of the component. In this work, samples of 3D-printed molybdenum lattices designed to have pore sizes ranging from 100 to 1000 µm were fabricated by two different suppliers. The dimensions of the lattice structures were characterized using an optical microscope, revealing that the lattice walls were almost systematically thicker than they were designed to be and in turn the pores are all smaller than they were designed to be. In many cases the pores were completely clogged. Several spectroscopic techniques were used to characterize the chemical composition of the materials, collectively indicating the presence of a thick layer of oxygen-rich material extending more than 1 µm below the surface. Compression testing revealed significant asymmetry in the mechanical behavior depending on which direction the force was applied relative to the print direction. Lastly, lithium wetting tests of several lattice samples were performed, and a sample with ~250-µm pores was found to soak up lithium quickly after initial wetting of the surface occurred. The implications of these results for future liquid metal plasma-facing component design are discussed.

Parsons, Matthew S. [Princeton Plasma Physics Labo↗
DOE OSTI2025

Real-time process monitoring and automated control for direct ink write 3D printing of frontally polymerizing thermosets

Additive manufacturing (AM) enables the fabrication of complex geometries, yet its application to thermosets remains limited by post-processing requirements. Frontal ring-opening metathesis polymerization (FROMP) offers a promising alternative, enabling energy-efficient, in situ curing of freestanding thermoset structures. This study presents a real-time process monitoring and automated control system for direct ink writing (DIW) of FROMP thermosets. By integrating thermochromic leuco dyes and computer vision, we enable real-time polymerization front tracking, allowing autonomous printing parameter adjustments for consistent geometries across resin formulations. The system’s accuracy was validated against manual tracking, demonstrating precise front velocity detection. Its adaptability was confirmed by printing freestanding mechanical springs with different resins, achieving consistent geometries and mechanical properties despite front velocity variations. These findings highlight the potential of automated DIW control for scalable, repeatable, and material-agnostic 3D printing of thermosets.

Mejia, Edgar Brian [Sandia National Laboratories (↗
DOE OSTI2024

Structure-property relationship between lignin structures and properties of 3D-printed lignin composites

Lignin is a low-cost and renewable bioresource with a huge annual production promising to prepare sustainable materials. However, the poor interfacial adhesion between many lignin-polymer pairs deteriorates the mechanical performance of the composites, which seriously limits the application of lignin in 3D printing via fused depositional modeling. This work examined lignin-polyamide 12 (PA 12) intermolecular interactions (e.g., hydrogen bonding) to address the interface challenge. To realize this goal, the phenolic hydroxyl content was increased for a kraft softwood lignin using a LiBr/HBr demethylation procedure, increasing phenoxy content by 61.7%. Increased hydrogen bonding interactions between modified lignin (Pine-Lig-OH) and PA 12 demonstrated a significantly improved molten dynamic modulus by rheological analysis. Regarding mechanical properties, by adding 20 wt% of Pine-Lig-OH, the tensile strength and Young's modulus reached 46.6 MPa and 1.62 GPa, 30.2% and 33.9% higher than PA 12, respectively. Further morphological analysis proved the interfacial interactions are enhanced by showing the difference in the phase gaps. The dynamic mechanical analysis (DMA) supported the conclusion that Pine-Lig-OH could interact with polymer chains, alternating segmental movements due to the strong interaction. Here, this study presents a method to enhance lignin composite properties by promoting interactions with the polymer matrix through modified functional groups, guiding future lignin composite research.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-performance aqueous zinc-ion hybrid capacitors based on 3D printed metal-organic framework cathodes

The zinc-ion hybrid capacitor is a promising energy storage device, but current overall capacity is limited by the capacitance of the carbon cathode. We have produced a hierarchically porous, nitrogen-doped carbon cathode with good cycling and mechanical stability by 3D printing and pyrolysis of the zinc-based metal–organic framework ZIF-8. When incorporated into a zinc-ion hybrid capacitor, we achieved an areal capacitance of 16.9 F cm -2 and energy density of 7.23 mW h cm -2 , outperforming zinc-ion hybrid capacitors based on conventional cathodes.

25 ENERGY STORAGE↗
NASA NTRS2019

The 3D Printing of Polyimide Aerogels

Polyimide aerogels are a nanoporous material made by extracting the liquid portion of a wet gel and replacing it with air, while still maintaining the porous solid internal architecture. This results in a material with extremely low densities, low thermal conductivities, high internal surfaces areas, and low dielectric constants. Currently, complex aerogel forms are not possible, since they require molds in order to be shaped. To overcome this challenge, we are attempting to use various additive manufacturing techniques to produce complex architectures. Three different approaches are being studied to accomplish this. One is to print using a viscous wet gel and have the structure solidify at the end of the print, another is to use a mixing tip, where a less viscous gel and the final chemical that causes gelation will be mixed as it is printing, allowing it to gel layer by layer, and the third is to use a UV curable aerogel with a UV light following behind to solidify the gel as it prints. To have these approaches be successful, the printing parameters and the aerogel's chemical formulation need to be optimized. The more harmonious these two factors can be made, the more defined and complex the resulting structure can be. Preliminary results show that 3D printing polyimide aerogels are a viable option, but further optimization must occur for reliable printing.

Nosel, Theresa↗
DOE OSTI2020

A 3D-printed molecular ferroelectric metamaterial

Significance Molecular ferroelectrics, which show the ability to switch the electromechanical activity by an external electric field, establish the basis for mechanical metamaterial technologies. Despite their theoretical promise, such mechanical metamaterials remain hindered by the lack of adaptive stimuli-responsive materials which can be effectively tuned “on demand” across time and length scales. Here, we unravel a printable mechanical metamaterial of imidazolium perchlorate with superior electromechanical coupling and reprogrammable stiffness. We propose a continuous rapid three-dimensional (3D) printing technique which can reduce the manufacturing time of ferroelectrics from hours down to minutes. The printed molecular ferroelectric metamaterial structure is then shown to enable a tunable-frequency vibration-isolating architecture. This study paves the way for rationally designed 3D-printable molecular ferroelectric metamaterials.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Enabling Technologies for Entrepreneurial Opportunities in 3D printing of SmallSats

A consortium of innovative experts in additive manufacturing (AM) comprising Northrup Grumman Technical Services, University of Texas at El Paso (UTEP), Configurable Space Microsystems Innovations & Applications Center (COSMIAC), NASA Glenn Research Center (GRC), and Youngstown State University, have made significant breakthroughs in the goal of creating the first complete 3D printed small satellite. Since AM machines are relatively inexpensive, this should lead to many entrepreneurial opportunities for the small satellite community. Our technology advancements are focused on the challenges of embedding key components within the structure of the article. We have demonstrated, using advanced fused deposition modeling techniques, complex geometric shapes which optimize the spacecraft design. The UTEP Keck Center has developed a method that interrupts the printing process to insert components into specific cavities, resulting in a spacecraft that has minimal internal space allocated for what traditionally were functional purposes. This allows us to increase experiment and instrument capability by provided added volume in a confined small satellite space. Leveraging initial progress made on a NASA contract, the team investigated the potential of new materials that exploit the AM process, producing candidate compositions that exceed the capabilities of traditional materials. These "new materials" being produced and tested include some that have improved radiation shielding, increased permeability, enhanced thermal properties, better conductive properties, and increased structural performance. The team also investigated materials that were previously not possible to be made. Our testing included standard mechanical tests such as vibration, tensile, thermal cycling, and impact resistance as well as radiation and electromagnetic tests. The initial results of these products and their performance will be presented and compared with standard properties. The new materials with the highest probability to disrupt the future of small satellite systems by driving down costs will be highlighted, in conjunction with the electronic embedding process.

Communications↗