Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vertical velocities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Velocity vector control system augmented with direct lift control

A pilot-controlled stability control system that employs direct lift control (spoiler control) with elevator control to control the flight path angle of an aircraft is described. A computer on the aircraft generates an elevator control signal and a spoiler control signal, using a pilot-controlled pitch control signal and pitch rate, vertical velocity, roll angle, groundspeed, engine pressure ratio and vertical acceleration signals which are generated on the aircraft. The direct lift control by the aircraft spoilers improves the response of the aircraft flight path angle and provides short term flight path stabilization against environmental disturbances.

Tisdale, H. F., Sr.↗

Site E - Virtual Tower High-Frequency Wind Velocity / Derived Data

This dataset contains Dual-Doppler wind reconstruction from stare lidar scans two rotor diameters south of the King Plains G02 turbine. The line-of-sight velocity data can be found in sa5.lidar.z03.b0 and sa1.lidar.z03.b0. The reconstruction is done neglecting the contribution from vertical velocity.

17 WIND ENERGY↗

Mesospheric heating due to intense tropospheric convection

A series of rocket measurements made twice daily at Wallops Island, Va., revealed a rapid heating of the mesosphere on the order of 10 K on days when thunderstorms or squall lines were in the area. This heating is explained as the result of frictional dissipation of vertically propagating internal gravity waves generated by intense tropospheric convection. Ray-tracing theory is used to determine the spectrum of gravity wave groups that actually reach mesospheric heights. This knowledge is used in an equation describing the spectral energy density of a penetrative convective element to calculate the fraction of the total energy initially available to excite those waves that do reach the level of heating. This value, converted into a vertical velocity, is used as the lower boundary condition for a multilayer model used to determine the detailed structure of the vertically propagating waves. The amount of frictional dissipation produced by the waves is calculated from the solutions of the frictionless model by use of a vertically varying eddy viscosity coefficient. The heating produced by the dissipation is then calculated from the thermodynamic equation.

Taylor, L. L.↗

Global atmospheric circulation statistics: Four year averages

Four year averages of the monthly mean global structure of the general circulation of the atmosphere are presented in the form of latitude-altitude, time-altitude, and time-latitude cross sections. The numerical values are given in tables. Basic parameters utilized include daily global maps of temperature and geopotential height for 18 pressure levels between 1000 and 0.4 mb for the period December 1, 1978 through November 30, 1982 supplied by NOAA/NMC. Geopotential heights and geostrophic winds are constructed using hydrostatic and geostrophic formulae. Meridional and vertical velocities are calculated using thermodynamic and continuity equations. Fields presented in this report are zonally averaged temperature, zonal, meridional, and vertical winds, and amplitude of the planetary waves in geopotential height with zonal wave numbers 1-3. The northward fluxes of sensible heat and eastward momentum by the standing and transient eddies along with their wavenumber decomposition and Eliassen-Palm flux propagation vectors and divergences by the standing and transient eddies along with their wavenumber decomposition are also given. Large interhemispheric differences and year-to-year variations are found to originate in the changes in the planetary wave activity.

Wu, M. F.↗

Updraft Model for Development of Autonomous Soaring Uninhabited Air Vehicles

Large birds and glider pilots commonly use updrafts caused by convection in the lower atmosphere to extend flight duration, increase cross-country speed, improve range, or simply to conserve energy. Uninhabited air vehicles may also have the ability to exploit updrafts to improve performance. An updraft model was developed at NASA Dryden Flight Research Center (Edwards, California) to investigate the use of convective lift for uninhabited air vehicles in desert regions. Balloon and surface measurements obtained at the National Oceanic and Atmospheric Administration Surface Radiation station (Desert Rock, Nevada) enabled the model development. The data were used to create a statistical representation of the convective velocity scale, w*, and the convective mixing-layer thickness, zi. These parameters were then used to determine updraft size, vertical velocity profile, spacing, and maximum height. This paper gives a complete description of the updraft model and its derivation. Computer code for running the model is also given in conjunction with a check case for model verification.

Allen, Michael J.↗

A velocity-command controller for a VTOL aircraft

A technique is presented for calculating feedback and feedforward gain matrices that enable a VTOL aircraft to track input commands of forward and vertical velocity while maintaining acceptable responses to pilot inputs. Leverrier's algorithm is used for determining a set of state-variable, feedback gains that force the closed-loop poles and zeros of one pilot-input transfer function to pre-selected positions in the s-plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity-command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. The method is used in a digital simulation of the CH-47 helicopter to control longitudinal dynamics.

Reid, G. F.↗

A velocity-command controller for a VTOL aircraft

A technique is presented for calculating feedback and feedforward gain matrices that enable a VTOL aircraft to track input commands of forward and vertical velocity while maintaining acceptable responses to pilot inputs. Leverrier's algorithm is used for determining a set of state-variable, feedback gains that force the closed-loop poles and zeros of one pilot-input transfer function to pre-selected positions in the s-plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity-command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. The method has been used in a digital simulation of the CH-47 helicopter to control longitudinal dynamics.

Reid, G. F.↗

Stochastic modal velocity field in rough-wall turbulence

Stochastically generated instantaneous velocity profiles are used to reproduce the outer region of rough-wall turbulent boundary layers in a range of Reynolds numbers extending from the wind tunnel to field conditions. Each profile consists in a sequence of steps, defined by the modal velocities and representing uniform momentum zones (UMZs), separated by velocity jumps representing the internal shear layers. Height-dependent UMZ is described by a minimal set of attributes: thickness, mid-height elevation, and streamwise (modal) and vertical velocities. These are informed by experimental observations and reproducing the statistical behaviour of rough-wall turbulence and attached eddy scaling, consistent with the corresponding experimental datasets. Sets of independently generated profiles are reorganized in the streamwise direction to form a spatially consistent modal velocity field, starting from any randomly selected profile. The operation allows one to stretch or compress the velocity field in space, increases the size of the domain and adjusts the size of the largest emerging structures to the Reynolds number of the simulated flow. By imposing the autocorrelation function of the modal velocity field to be anchored on the experimental measurements, we obtain a physically based spatial resolution, which is employed in the computation of the velocity spectrum, and second-order structure functions. The results reproduce the Kolmogorov inertial range extending from the UMZ and their attached-eddy vertical organization to the very-large-scale motions (VLSMs) introduced with the reordering process. The dynamic role of VLSM is confirmed in the –u'w' co-spectra and in their vertical derivative, representing a scale-dependent pressure gradient contribution.

42 ENGINEERING↗

Performance and Wake Characterization of a Model Hydrokinetic Turbine: The Reference Model 1 (RM1) Dual Rotor Tidal Energy Converter

The mechanical power and wake flow field of a 1:40 scale model of the US Department of Energy’s Reference Model 1 (RM1) dual rotor tidal energy converter are characterized in an open-channel flume to evaluate power performance and wake flow recovery. The NACA-63(4)-24 hydrofoil profile in the original RM1 design is replaced with a NACA-4415 profile to minimize the Reynolds dependency of lift and drag characteristics at the test chord Reynolds number. Precise blade angular position and torque measurements were synchronized with three acoustic Doppler velocimeters (ADV) aligned with each rotor centerline and the midpoint between the rotor axes. Flow conditions for each case were controlled to maintain a hub height velocity, uhub= 1.04 ms−1, a flow Reynolds number, ReD= 4.4 × 105, and a blade chord length Reynolds number, Rec= 3.1 × 105. Performance was measured for a range of tip-speed ratios by varying rotor angular velocity. Peak power coefficients, CP= 0.48 (right rotor) and CP= 0.43 (left rotor), were observed at a tip speed ratio, λ= 5.1. Vertical velocity profiles collected in the wake of each rotor between 1 and 10 rotor diameters are used to estimate the turbulent flow recovery in the wake, as well as the interaction of the counter-rotating rotor wakes. The observed performance characteristics of the dual rotor configuration in the present study are found to be similar to those for single rotor investigations in other studies. Similarities between dual and single rotor far-wake characteristics are also observed.

30 DIRECT ENERGY CONVERSION↗

Simulation evaluation of two VTOL control/display systems in IMC approach and shipboard landing

Two control/display systems, which differed in overall complexity but were both designed for VTOL flight operations to and from small ships in instrument meteorological conditions (IMC), were tested using the Ames Flight Simulator for Advanced Aircraft (FSAA). Both systems have attitude command in transition and horizontal-velocity command in hover; the more complex system also has longitudinal-acceleration and flightpath-angle command in transition, and vertical-velocity command in hover. The most important overall distinction between the two systems for the viewpoint of implementation is that in one - the more complex - engine power and nozzle position are operated indirectly through flight controllers, whereas in the other they are operated directly by the pilot. Simulated landings were made on a moving model of a DD 963 Spruance-class destroyer. Acceptable transitions can be performed in turbulence of 3 m/sec rms using either system. Acceptable landings up to sea state 6 can be performed using the more complex system, and up to sea state 5 using the other system.

Merrick, V. K.↗

A Van de Graaf source mechanism for middle atmospheric vertical electric fields

It is proposed that meteoric and other debris descending through the mesosphere constitute a natural Van de Graaf generator for vertical electric fields within the mesosphere. Dust and aerosol particles falling from above 85 km are charged negatively in the upper D-region. Charge is lost in the region below 70 km. This net charge transport creates a vertical polarization electric field. Calculated fields are in the range of 10 mV/m for the average input of meteoric debris. Observed vertical electric fields are confined to a few occasions when large fields of the order of 4 V/m are observed to maximize at 65 km. Calculated fields from this model also maximize at this altitude, but a special event with increased dust density or another mechanism to increase relative vertical velocity is required to explain the large fields. Such large values are the exception rather than the rule for D-region vertical electric fields.

Aikin, A. C.↗

Buffering of stratospheric circulation by changing amounts of tropical ozone - A Pinatubo case study

Stratospheric aerosol from Mount Pinatubo heated the tropical lower stratosphere by about 0.3 K/day mainly due to absorption of terrestrial infrared radiation. This heating was dissipated by: (1) an observed increase in stratospheric temperatures, which enhanced the radiation cooling; (2) additional mean upward motion, observed for the aerosol cloud, which led to adiabatic cooling; and (3) reductions in ozone concentrations resulting from enhanced upward motions. Each of these processes operated on a different time scale: maximum temperatures were observed after about 90 days; maximum ozone losses of about -1.5 ppm occurred after 140 days when the enhanced vertical velocities effectively lifted the ozone profile by about 2 km. We believe this shows that ozone plays an important role in buffering vertical motion in the tropical lower stratosphere, and hence the residual Brewer Dobson circulation of the whole stratosphere.

Kinne, S.↗

Rain Characteristics and Large-Scale Environments of Precipitation Objects with Extreme Rain Volumes from TRMM Observations

This study adopts a "precipitation object" approach by using 14 years of Tropical Rainfall Measuring Mission (TRMM) Precipitation Feature (PF) and National Centers for Environmental Prediction (NCEP) reanalysis data to study rainfall structure and environmental factors associated with extreme heavy rain events. Characteristics of instantaneous extreme volumetric PFs are examined and compared to those of intermediate and small systems. It is found that instantaneous PFs exhibit a much wider scale range compared to the daily gridded precipitation accumulation range. The top 1% of the rainiest PFs contribute over 55% of total rainfall and have 2 orders of rain volume magnitude greater than those of the median PFs. We find a threshold near the top 10% beyond which the PFs grow exponentially into larger, deeper, and colder rain systems. NCEP reanalyses show that midlevel relative humidity and total precipitable water increase steadily with increasingly larger PFs, along with a rapid increase of 500 hPa upward vertical velocity beyond the top 10%. This provides the necessary moisture convergence to amplify and sustain the extreme events. The rapid increase in vertical motion is associated with the release of convective available potential energy (CAPE) in mature systems, as is evident in the increase in CAPE of PFs up to 10% and the subsequent dropoff. The study illustrates distinct stages in the development of an extreme rainfall event including: (1) a systematic buildup in large-scale temperature and moisture, (2) a rapid change in rain structure, (3) explosive growth of the PF size, and (4) a release of CAPE before the demise of the event.

TRMM↗

The NACA Impact Basin and Water Landing Tests of a Float Model at Various Velocities and Weights

The first data obtained in the United States under the controlled testing conditions necessary for establishing relationships among the numerous parameters involved when a float having both horizontal and vertical velocity contacts a water surface are presented. The data were obtained at the NACA impact basin. The report is confined to a presentation of the relationship between resultant velocity and impact normal acceleration for various float weights when all other parameters are constant. Analysis of the experimental results indicated that the maximum impact normal acceleration was proportional to the square of the resultant velocity, that increases in float weight resulted in decreases in the maximum impact normal acceleration, and that an increase in the flight-path angle caused increased impact normal acceleration.

Batterson, Sidney A↗

The O(+) Density Trough at 5000 km Altitude in the Polar Cap

At altitudes near 5000 km over the southern polar cap region of the terrestrial magnetosphere/ionosphere, the Thermal Ion Dynamics Experiment (TIDE) on board the Polar satellite has observed O(+) ion density trough regions, in which the densities were at least one order of magnitude lower than the surrounding O(+) densities. In the 0" density trough regions, the estimated O+ densities were generally lower than 0.01 per cc. The boundaries between normal density level regions and the trough density regions were usually abrupt transitions. From 1 December 1997 to 30 November 1998, polar cap O(+) troughs in Polar/TIDE observations occurred at a frequency of about 48%. Statistical examination of the Polar perigee observations from 1 December 1997 to 30 November 1998 shows that the Polar perigee passes evenly covered the southern polar cap region, while the O(+) density trough was always located on the nightside portion of the polar cap magnetosphere/ionosphere, and that invariant latitude spans of such troughs could be as large as 23 deg. in extent. The trough occurrence displayed a strong seasonal dependence; in the winter season (e.g., for July in the Southern Hemisphere) the O(+) ion density trough occurrence frequency ranged up to 92%, while in the summer season (e.g., for January in the Southern Hemisphere) it decreased to as low as 15%. Our statistical results show that the trough occurrence was generally anticorrelated with solar wind dynamic pressure in the solar wind dynamic pressure range 0.8 - 2.6 nanopascal. The O(+) ion density trough occurrence appeared relatively independent of the geomagnetic Kp index, IMF Bz, and By conditions. However, as suggested by the seasonal dependence, the O(+) ion density trough occurrence was strongly related to the solar zenith angle (SZA). In the SZA range 50 deg. to 125 deg., the trough occurrence increased monotonically with SZA. In addition, we sought to determine consistent density and velocity signatures at lower altitudes associated the O(+) ion density trough at 5000 km by examining the near-simultaneous O(+) densities and vertical velocities observed by the DMSP satellite group orbiting at 840 km altitude. However, consistent correlations between the dual altitudes were not reliably established from the present examinations.

Zeng, W.↗

An analysis of the vertical structure equation for arbitrary thermal profiles

The vertical structure equation is a singular Sturm-Liouville problem whose eigenfunctions describe the vertical dependence of the normal modes of the primitive equations linearized about a given thermal profile. The eigenvalues give the equivalent depths of the modes. The spectrum of the vertical structure equation and the appropriateness of various upper boundary conditions, both for arbitrary thermal profiles were studied. The results depend critically upon whether or not the thermal profile is such that the basic state atmosphere is bounded. In the case of a bounded atmosphere it is shown that the spectrum is always totally discrete, regardless of details of the thermal profile. For the barotropic equivalent depth, which corresponds to the lowest eigen value, upper and lower bounds which depend only on the surface temperature and the atmosphere height were obtained. All eigenfunctions are bounded, but always have unbounded first derivatives. It was proved that the commonly invoked upper boundary condition that vertical velocity must vanish as pressure tends to zero, as well as a number of alternative conditions, is well posed. It was concluded that the vertical structure equation always has a totally discrete spectrum under the assumptions implicit in the primitive equations.

Cohn, Stephen E.↗

An analysis of the vertical structure equation for arbitrary thermal profiles

The vertical structure equation is a singular Sturm-Liouville problem whose eigenfunctions describe the vertical dependence of the normal modes of the primitive equations linearized about a given thermal profile. The eigenvalues give the equivalent depths of the modes. The spectrum of the vertical structure equation and the appropriateness of various upper boundary conditions, both for arbitrary thermal profiles were studied. The results depend critically upon whether or not the thermal profile is such that the basic state atmosphere is bounded. In the case of a bounded atmosphere it is shown that the spectrum is always totally discrete, regardless of details of the thermal profile. For the barotropic equivalent depth, which corresponds to the lowest eigen value, upper and lower bounds which depend only on the surface temperature and the atmosphere height were obtained. All eigenfunctions are bounded, but always have unbounded first derivatives. It was proved that the commonly invoked upper boundary condition that vertical velocity must vanish as pressure tends to zero, as well as a number of alternative conditions, is well posed. It was concluded that the vertical structure equation always has a totally discrete spectrum under the assumptions implicit in the primitive equations.

Cohn, Stephen E.↗

Plate tectonics from VLBI and SLR global data

This study is based on data derived from fifteen years of observations of the SLR (side-looking radar) network and six years of the VLBI (very long baseline interferometry) network. In order to use all available information VLBI and SLR global data sets were combined in a least squares fashion to calculate station horizontal velocities. All significant data pertaining to a single site contribute to the station horizontal motion. The only constraint on the solution is that no vertical motion is allowed. This restriction does not greatly affect the precision of the overall solution given the fact that the expected vertical motion for most stations, even those experiencing post glacial uplift, is well under 1 cm/yr. Since the average baseline is under 4,000 km, only a small fraction of the station vertical velocity is translated into baseline rates so that the error introduced in the solution by restricting up-down station movement is minimal. As a reference, station velocities were then compared to the ones predicted by the NUVEL-1 geological model of DeMets et al. (1990). The focus of the study is on analyzing these discrepancies for global plate tectonics as well as regional tectonic settings. The method used also allows us not only to derive horizontal motion for individual stations but also to calculate Euler vectors for those plates that have enough stations located on the stable interior like North America, Pacific, Eurasia, and Australia.

Harrison, Christopher G. A.↗