Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Canonical forms of multidimensional steady inviscid flows

Canonical forms and canonical variables for inviscid flow problems are derived. In these forms the components of the system governed by different types of operators (elliptic and hyperbolic) are separated. Both the incompressible and compressible cases are analyzed, and their similarities and differences are discussed. The canonical forms obtained are block upper triangular operator form in which the elliptic and non-elliptic parts reside in different blocks. The full nonlinear equations are treated without using any linearization process. This form enables a better analysis of the equations as well as better numerical treatment. These forms are the analog of the decomposition of the one dimensional Euler equations into characteristic directions and Riemann invariants.

Taasan, Shlomo↗
NASA NTRS2002

Numerical Modeling of Cavitating Venturi: A Flow Control Element of Propulsion System

In a propulsion system, the propellant flow and mixture ratio could be controlled either by variable area flow control valves or by passive flow control elements such as cavitating venturies. Cavitating venturies maintain constant propellant flowrate for fixed inlet conditions (pressure and temperature) and wide range of outlet pressures, thereby maintain constant, engine thrust and mixture ratio. The flowrate through the venturi reaches a constant value and becomes independent of outlet pressure when the pressure at throat becomes equal to vapor pressure. In order to develop a numerical model of propulsion system, it is necessary to model cavitating venturies in propellant feed systems. This paper presents a finite volume model of flow network of a cavitating venturi. The venturi was discretized into a number of control volumes and mass, momentum and energy conservation equations in each control volume are simultaneously solved to calculate one-dimensional pressure, density, and flowrate and temperature distribution. The numerical model predicts cavitations at the throat when outlet pressure was gradually reduced. Once cavitation starts, with further reduction of downstream pressure, no change in flowrate is found. The numerical predictions have been compared with test data and empirical equation based on Bernoulli's equation.

Majumdar, Alok↗
NASA NTRS2005

Reciprocating Feed System Development Status

The reciprocating feed system (RFS) is an alternative means of providing high pressure propellant flow at low cost and system mass, with high fail-operational reliability. The RFS functions by storing the liquid propellants in large, low-pressure tanks and then expelling each propellant through two or three small, high-pressure tanks. Each RFS tank is sequentially filled, pressurized, expelled, vented, and refilled so as to provide a constant, or variable, mass flow rate to the engine. This type of system is much lighter than a conventional pressure fed system in part due to the greatly reduced amount of inert tank weight. The delivered payload for an RFS is superior to that of conventional pressure fed systems for conditions of high total impulse and it is competitive with turbopump systems, up to approximately 2000 psi. An advanced version of the RFS uses autogenous pressurization and thrust augmentation to achieve higher performance. In this version, the pressurization gases are combusted in a small engine, thus making the pressurization system, in effect, part of the propulsion system. The RFS appears to be much less expensive than a turbopump system, due to reduced research and development cost and hardware cost, since it is basically composed of small high- pressure tanks, a pressurization system, and control valves. A major benefit is the high reliability fail-operational mode; in the event of a failure in one of the three tank-systems, it can operate on the two remaining tanks. Other benefits include variable pressure and flow rates, ease of engine restart in micro-gravity, and enhanced propellant acquisition and control under adverse acceleration conditions. We present a system mass analysis tool that accepts user inputs for various design and mission parameters and calculates such output values payload and vehicle weights for the conventional pressure fed system, the RFS, the Autogenous Pressurization Thrust Augmentation (APTA) RFS, and turbopump systems. Using this tool, a preliminary design of a representative crew exploration vehicle (CEV) has been considered. The design parameters selected for a representative system were modeled after the orbital maneuvering system (OMS) on the Shuttle Orbiter, with an increase of roughly a factor of ten in the delta- V capability and a greater thrust (30,000 lbs, vs. 12,000 lbs). Both storable and cryogenic propellants were considered. Results show that a RFS is a low mass alternative to conventional pressure fed systems, with a substantial increase in payload capability and that it is weight-competitive with turbopump systems at low engine pressure (a few hundred psi); at high engine pressures, the APTA RFS appears to offer the highest payload. We also present the status of the RFS test bed fabrication, assembly, and checkout. This test bed is designed to provide flow rates appropriate for engines in the roughly 10,000 to 30,000 lb thrust range.

Trewek, Mary↗
NASA NTRS1991

Prediction of unsteady aerodynamic loads in cascades using the linearized Euler equations on deforming grids

A linearized Euler solver for calculating unsteady flows in turbomachinery blade rows due to both incident gusts and blade motion is presented. Using the linearized Euler technique, one decomposes the flow into a mean (or steady) flow plus an unsteady, harmonically varying, small disturbance flow. Linear variable coefficient equations describe the small disturbance behavior of the flow, and are solved using a pseudo-time marching Lax-Wendroff scheme. For the blade motion problem, a harmonically deforming computational rid that conforms to the motion of vibrating blades eliminates large error producing mean flow gradient terms that would otherwise appear in the unsteady flow tangency boundary condition. The paper also presents a new, numerically exact, nonreflecting far-field boundary condition based on an eigenanalysis of the discretized equations. Computed flow solutions demonstrate the computational accuracy and efficiency of the present method. The solution of the linearized Euler equations requires one to two orders of magnitude less computer time than solution of the nonlinear Euler equations using traditional time-accurate time-marching techniques. In addition, the deformable grid significantly improves the accuracy of the solution.

Hall, Kenneth C.↗
NASA NTRS1991

Standard test case for a low-speed, turbulent junction vortex flow

The mean flow structure upstream, around within, and in the near wake of a turbulent junction or horseshoe vortex is reported for an incompressible subsonic flow. Measurements of the primitive variables of velocity and pressure are reported on all surfaces bounding the region of the vortex flow and on three transverse and one streamwise plane within the flowfield itself for comparisons between the measured and any calculated flow variables. Detailed surface flow visualizations and some direct force measurements of surface shear stress are also available. The data is a highly detailed, coherent, self-consistent set offered to the computational fluid mechanics community as a standard test case for the evaluation of the capability of numerical solvers intended for predicting the flowfield in such a complex, separated, three-dimensional turbulent flow. This data base is available for copying to user supplied tapes or for transmission via BITNET, as well as in two National Technical Information Service (NTIS) reports.

Pierce, F. J.↗
NASA NTRS1992

Some effects of oscillation waveform and amplitude on unsteady turbulent shear flows

Some physical features of several unsteady separating turbulent boundary layers are presented for practical Reynolds numbers and reduced frequencies such as for helicopter and turbomachinery flows. The effects of unsteadiness amplitude and waveform are examined for flows along the floor of a converging and diverging wind tunnel test section. At the end of the converging portion, the mean skin friction coefficient normalized on the mean dynamic pressure is independent of the waveform and amplitude within low experimental uncertainties. In the detaching and detached portions of the flow, wall values of the fraction of time that the flow moves downstream of gamma sub pu, which is a separated flow state variable, shows that oscillation waveform and amplitude strongly influence the detached flow behavior. Distributions of gamma sub pu during a cycle indicate hysteresis within the detached flow and the effects of the higher harmonics of pressure gradient and velocity.

Agarwal, Naval K.↗
NASA NTRS2003

Piloted Ignition of Polypropylene/Glass Composites in a Forced Air Flow

The Forced Ignition and Spread Test (FIST) is being used to study the flammability characteristics of combustible materials in forced convective flows. The FIST methodology is based on the ASTM E-1321, Lateral Ignition and Flame Spread Test (LIFT) which is used to determine the ignition and flame spread characteristics of materials, and to produce 'Flammability Diagrams' of materials. The LIFT apparatus, however, relies on natural convection to bring air to the combustion zone and the fuel vapor to the pilot flame, and thus cannot describe conditions where the oxidizer flow velocity may change. The FIST on the other hand, by relying on a forced flow as the dominant transport mechanism, can be used to examine variable oxidizer flow characteristics, such as velocity, oxygen concentration, and turbulence intensity, and consequently has a wider applicability. Particularly important is its ability to determine the flammability characteristics of materials used in spacecraft since in the absence of gravity the only flow present is that forced by the HVAC of the space facility. In this paper, we report work on the use of the FIST approach on the piloted ignition of a blended polypropylene fiberglass (PP/GL) composite material exposed to an external radiant flux in a forced convective flow of air. The effect of glass concentration under varying external radiant fluxes is examined and compared qualitatively with theoretical predictions of the ignition process. The results are used to infer the effect of glass content on the fire safety characteristics of composites.

Fernandez-Pello, A. C.↗
NASA NTRS1973

Optimization of wave cancellation in variable porosity transonic wind tunnel flows

A technique has been developed which is capable of determining the optimum wall configuration for a variable porosity perforated wall transonic wind tunnel. The technique is based on a mathematical model arrived at by considering the results of theory and past experimental investigations. A performance index was determined as a function of the significant wind tunnel parameters by comparing a formulation of this mathematical model, using MSFC 14 inch Trisonic Wind Tunnel experimental results, to interference free results. The resulting relationship was then used to determine the combination of wind tunnel parameters which should yield minimum reflected wave interference. A theoretical development of wall porosity requirements for thick wall inclined hole test sections is included which follows the trends and generally the magnitude of available experimental data. This theory is useful in studying the present variable porosity case, but also should be of value in studies concerning the wave cancellation process for fixed porosity walls.

Davis, J. W.↗
NASA NTRS1992

Potential Flows From Three-Dimensional Complex Variables

Report presents investigation of several functions of three-dimensional complex variable, with emphasis on potential-flow fields computed from these functions. Part of continuing research on generalization of well-established two-dimensional complex analysis to three and more dimensions.

Martin, E. Dale↗
NASA NTRS1946

Some Effects of Compressibility on the Flow Through Fans and Turbines

The laws of conservation of mass, momentum, and energy are applied to the compressible flow through a two-dimensional cascade of airfoils. A fundamental relation between the ultimate upstream and downstream flow angles, the inlet Mach number, and the pressure ratio across the cascade is derived. Comparison with the corresponding relation for incompressible flow shows large differences. The fundamental relation reveals two ranges of flow angles and inlet Mach numbers, for which no ideal pressure ratio exists. One of these nonideal operating ranges is analogous to a similar type in incompressible flow. The other is characteristic only of compressible flow. The effect of variable axial-flow area is treated. Some implications of the basic conservation laws in the case of nonideal flow through cascades are discussed.

Perl, W.↗
NASA NTRS1982

Second order closure for variable density free shear layer

A full second order closure turbulence model for the prediction of free shear flows with variable density is developed. The importance of density fluctuations due to inhomogeneities in fluid composition is emphasized. Some simplicity is achieved by using density weighted averaging to account implicitly for density fluctuation effects. Transport equations for various second order correlations - such as Reynolds stress, turbulent mass fluxes or density velocity correlations - are derived, modelled and solved, together with the mean equations for momentum and species conservation. Solutions of these equations are compared with the two different sets of experimental data for low speed free mixing layers (helium into nitrogen and freon 12 into air).

Vandromme, D.↗
NASA NTRS2013

Characterization of Fluorescent Polystyrene Microspheres for Advanced Flow Diagnostics

Fluorescent dye-doped polystyrene latex microspheres (PSLs) are being developed for velocimetry and scalar measurements in variable property flows. Two organic dyes, Rhodamine B (RhB) and dichlorofluorescence (DCF), are examined to assess laser-induced fluorescence (LIF) properties for flow imaging applications and single-shot temperature measurements. A major interest in the current research is the application of safe dyes, thus DCF is of particular interest, while RhB is used as a benchmark. Success is demonstrated for single-point laser Doppler velocimetry (LDV) and also imaging fluorescence, excited via a continuous wave 2 W laser beam, for exposures down to 10 ms. In contrast, when exciting with a pulsed Nd:YAG laser at 200 mJ/pulse, no fluorescence was detected, even when integrating tens of pulses. We show that this is due to saturation of the LIF signal at relatively low excitation intensities, 4-5 orders of magnitude lower than the pulsed laser intensity. A two-band LIF technique is applied in a heated jet, indicating that the technique effectively removes interfering inputs such as particle diameter variation. Temperature measurement uncertainties are estimated based upon the variance measured for the two-band LIF intensity ratio and the achievable dye temperature sensitivity, indicating that particles developed to date may provide about +/-12.5 C precision, while future improvements in dye temperature sensitivity and signal quality may enable single-shot temperature measurements with sub-degree precision.

Maisto, Pietro M. F.↗