SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Remote flow metering error due to mass accumulation from thermal expansion of incompressible fluid, analyzing transient temperature distribution in finite duct
An analysis has been developed which relates the effects of inelastic behavior of Y2O3 stabilized ZrO2 (YSZ) materials. The results show these materials to be sensitive to small changes in temperature and are supported by measurements of inelastic behavior in disk and bar specimens at temperatures as low as 1010 C (1850 F). At higher thermomechanical loads, the test specimens can deform to strains greater than 1 percent and for bar specimens, with sufficient strength, to remain bonded to the metallic substrate.
A laser pulse technique to measure the thermal diffusivity of diamond films deposited on a silicon substrate is developed. The effective thermal diffusivity of diamond film on silicon was measured by observing the phase and amplitude of the cyclic thermal waves generated by the laser pulses. An analytical model is developed to calculate the effective in-plane (face-parallel) diffusivity of a two layer system. The model is used to reduce the effective thermal diffusivity of the diamond/silicon sample to a value for the thermal diffusivity and conductivity of the diamond film. Phase and amplitude measurements give similar results. The thermal conductivity of the films is found to be better than that of type 1a natural diamond.
Ultra-high-temperature ceramics (UHTCs), including TiC, Ti 11 B₂, and Zr 11 B₂, show great potential for plasma-facing components due to their excellent high-temperature properties prior to irradiation. However, their response to neutron irradiation remains insufficiently understood, limiting robust assessment of their viability for fusion energy applications. Here, this study examines the thermal conductivity, dimensional stability and microstructure of TiC, TiB₂, and ZrB₂ following neutron irradiation at temperatures of 200–1000 °C and fast neutron fluences of 2.0 × 10 25 to 1.1 × 10 26 n/m 2 (E > 0.1 MeV). Lattice swelling measured by synchrotron X-ray diffraction in all three UHTCs was maximized at 200 °C and decreased with increasing irradiation temperature, with no evidence of amorphization observed at 200 °C. Above 600 °C, significant macroscopic volume swelling was observed in irradiated Ti 11 B₂ and Zr 11 B₂, but not in TiC, likely due to cavity formation in the diborides. The post-irradiation thermal conductivity, measured at the irradiation temperature, ranged from 28 to 45 W/m·K, representing a 34–45% reduction relative to the unirradiated material. Notably, neutron-irradiated UHTCs exhibit recoverable thermal conductivity at elevated temperatures, comparable to ferritic–martensitic steels and potentially superior to W when transmutation effects are considered, highlighting promise for shielding or armor plasma-facing components. At 600 °C, both thermal conductivity degradation and lattice swelling saturated at doses exceeding 2–4 dpa.
The quest for more energy-efficient green aircraft, dictates that all systems, including the ice protection system (IPS), be closely examined for ways to reduce energy consumption and to increase efficiency. A thermal ice protection systems must protect the aircraft from the hazardous effects of icing, and yet it needs to do so as efficiently as possible. The system can no longer be afforded the degree of over-design in power usage they once were. To achieve these more exacting designs, a better understanding of the heat and mass transport phenomena involved during an icing encounter is needed.
Multiscale micromechanics predictions have been made for the effective thermal conductivities and local thermal fields for a novel 3D woven composite thermal protection system material. The Multiscale Recursive Micromechanics approach, which enables micromechanics models to call other micromechanics models (or themselves recursively) to consider finer and finer length scales, has been employed. The multiscale model uses a recently developed version of the High-Fidelity Generalized Method of Cells micromechanics theory at each of three length scales. Results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures.
Multiscale micromechanics predictions have been made for the effective thermal conductivities and local thermal fields for a novel 3D woven composite thermal protection system material. The Multiscale Recursive Micromechanics approach, which enables micromechanics models to call other micromechanics models (or themselves recursively) to consider finer and finer length scales, has been employed. The multiscale model uses a recently developed version of the High-Fidelity Generalized Method of Cells micromechanics theory at each of three length scales. Results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures.
This report presents the results of both the fifth and sixth year effort of a research program conducted for NASA-LeRC by The University of Texas at San Antonio (UTSA). The research included on-going development of methodology for a probabilistic material strength degradation model. The probabilistic model, in the form of a postulated randomized multifactor equation, provides for quantification of uncertainty in the lifetime material strength of aerospace propulsion system components subjected to a number of diverse random effects. This model is embodied in the computer program entitled PROMISS, which can include up to eighteen different effects. Presently, the model includes five effects that typically reduce lifetime strength: high temperature, high-cycle mechanical fatigue, low-cycle mechanical fatigue, creep and thermal fatigue. Statistical analysis was conducted on experimental Inconel 718 data obtained from the open literature. This analysis provided regression parameters for use as the model's empirical material constants, thus calibrating the model specifically for Inconel 718. Model calibration was carried out for five variables, namely, high temperature, high-cycle and low-cycle mechanical fatigue, creep and thermal fatigue. Methodology to estimate standard deviations of these material constants for input into the probabilistic material strength model was developed. Using an updated version of PROMISS, entitled PROMISS93, a sensitivity study for the combined effects of high-cycle mechanical fatigue, creep and thermal fatigue was performed. Then using the current version of PROMISS, entitled PROMISS94, a second sensitivity study including the effect of low-cycle mechanical fatigue, as well as, the three previous effects was performed. Results, in the form of cumulative distribution functions, illustrated the sensitivity of lifetime strength to any current value of an effect. In addition, verification studies comparing a combination of high-cycle mechanical fatigue and high temperature effects by model to the combination by experiment were conducted. Thus, for Inconel 718, the basic model assumption of independence between effects was evaluated. Results from this limited verification study strongly supported this assumption.
The available experimental data base on the effects of exercise, posture and the environment (heat) on the blood volume, composition and concentration in humans is surveyed in depth to synthesize supportable conclusions. A large disparity is noted in the effective controls which were initiated in previous experimental conditions, resulting in contradictory findings regarding, e.g., hemoconcentrations and hemodilution in response to exercise. Comparisons between the results of exercise and of supine, seated and upright subjects has underscored the importance of gravity in hemoconcentration, particularly in the legs, and the generation of aldotestosterone. Hemoconcentration has been confirmed to increase with exercise in a seated or supine position. Exercise in a heated environment transfers cardiac output from core areas and reduces filtration efficiencies. Also, plasma volume increases, an action which cannot yet be associated with crystalloidal or colloidal influences on the osmotic behavior of cell walls.
A generalized multi-phase formulation for cavitation in fluids operating at temperatures elevated relative to their critical temperatures is presented. The thermal effects and the accompanying property variations due to phase change are modeled rigorously. Thermal equilibrium is assumed and fluid thermodynamic properties are specified along the saturation line using the NIST-12 databank. Fundamental changes in the physical characteristics of the cavity when thermal effects become pronounced are identified; the cavity becomes more porous, the interface less distinct, and has increased entrainment when temperature variations are present. Quantitative estimates of temperature and pressure depressions in both liquid nitrogen and liquid hydrogen were computed and compared with experimental data of Hord for hydrofoils. Excellent estimates of the leading edge temperature and pressure depression were obtained while the comparisons in the cavity closure region were reasonable. Liquid nitrogen cavities were consistently found to be in thermal equilibrium while liquid hydrogen cavities exhibited small, but distinct, non-equilibrium effects.
Effect of nuclear radiation on optical properties of spacecraft thermal control coatings
The X-ray and gamma-ray induced decomposition of ammonium perchlorate was studied by optical, transmission, and scanning electron microscopy. This material is a commonly used oxidizer in solid propellents which could be employed in deep-space probes, and where they will be subjected to a variety of radiations for as long as ten years. In some respects the radiation-induced damage closely resembles the effects produced by thermal decomposition, but in other respects the results differ markedly. Similar radiation and thermal effects include the following: (1) irregular or ill-defined circular etch pits are formed in both cases; (2) approximately the same size pits are produced; (3) the pit density is similar; (4) the c face is considerably more reactive than the m face; and (5) most importantly, many of the etch pits are aligned in crystallographic directions which are the same for thermal or radiolytic decomposition. Thus, dislocations play an important role in the radiolytic decomposition process.
Thermal radiation is a dominant mode of heat transfer in combustion/gasification, packed/circulating bed reactors, and energy storage/conversion devices. In hydrocarbon fuel combustion, the high absorption and emission of product gases like CO 2 and H 2 O significantly affect the heat transfer characteristics. It is essential to understand the radiative energy propagation in such applications. In the present study, we developed a framework to implement the P-1 radiation model in MFiX for Eulerian-Eulerian (Two fluid-TFM) and Eulerian-Lagrangian (Discrete element-DEM and Particle in cell-PIC) models. The P-1 is a simplification of the spherical harmonics method. The framework has been verified on various flue gas conditions. The verified solver results are validated against the benchmark results available in the literature. The verified and validated gray and non-gray weighted sum of gray gas models is evaluated for dry and wet flue gas conditions. Further, they are also used to study gas-solid flows in a fluidized bed/riser.
Carbon nanotubes (CNTs) can greatly enhance the strength of metal matrix composites while resulting in ductility loss. This strength-ductility tradeoff dilemma always confines the development of material design and real-life applications. Here in this work, a temperature dependent strengthening analytical model is proposed for CNT reinforced metal matrix composites which considers three common strengthening mechanisms: Orowan looping effect, thermal expansion mismatch effect, and load bearing effect. The proposed model can predict composite material strength with different volume fractions of CNTs and under different temperatures. Combining the strengthening model with the stress based modified Mohr-Coulomb (sMMC) ductile fracture model, a ductility analytical model is then derived. This ductility analytical model includes the influences of temperature, multi-axial stress loading conditions, as well as the aforementioned three strengthening mechanisms. A good agreement has been achieved between literature published experimental data and analytical predictions for both composite material strength and ductility loss. The proposed two analytical models can provide a straightforward way to study the strength-ductility relationship for CNT reinforced metal matrix composites over a wide range of temperatures and different stress states, and then provide guidance on new material design and processing.
The high-pressure equation of state (EOS) of energetic materials (EMs) is important for continuum and mesoscale models of detonation performance and initiation safety. Additionally, obtaining a high-fidelity EOS of the insensitive EM 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) has proven to be difficult because of challenges in experimental characterization at high pressures (HPs). In this work, powder X-ray diffraction patterns were fitted using the recently discovered monoclinic I2/a phase above 4 GPa, which shows that TATB is less compressible than when indexed with the triclinic $P\bar{1}$ phase. First-principles calculations were performed with Perdew–Burke–Ernzerhof (PBE) and PBE0 functionals including thermal effects using the $P\bar{1}$ phase. PBE0 improves the description of hydrogen bonding and thus predicts accurate planar a and b lattice parameters under ambient conditions. However, discrepancies in the predicted lattice parameters above 4–10 GPa compared with experimental measurements indexed with $P\bar{1}$ are further evidence of a structural modification at high pressure. Layer sliding defects are formed during molecular dynamics simulations, which induces an anharmonic effect on the thermal expansion of the c lattice parameter. In short, the results provide several insights into determining high-fidelity EOS parameters for TATB and other molecular crystals.
Here we report measurements of K -shell fluorescence lines induced by fast electrons in ramp-compressed Co targets. The fluorescence emission was stimulated by fast electrons generated through short-pulse laser-solid interaction with an Al target layer. Compression up to 2.1 × solid density was achieved while maintaining temperatures well below the Fermi energy, effectively removing the thermal effects from consideration. We observed small but unambiguous redshifts in the K β fluorescence line relative to unshifted Cu K α . Redshifts up to 2.6 eV were found to increase with compression and to be consistent with predictions from self-consistent models based on density-functional theory.
The HyRAM+ software toolkit provides a basis for conducting quantitative risk assessment and consequence modeling for hydrogen, methane, and propane systems. HyRAM+ is designed to facilitate the use of state-of-the-art models to conduct robust, repeatable assessments of safety, hazards, and risk. HyRAM+ integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, characterizing hazards (thermal effects from jet fires, overpressure effects from delayed ignition), and assessing impacts on people. HyRAM+ is developed at Sandia National Laboratories to support the development and revision of national and international codes and standards, and to provide developed models in a publicly-accessible toolkit usable by all stakeholders. This document provides a description of the methodology and models contained in HyRAM+ version 4.1. The two most significant changes for HyRAM+ version 4.1 from HyRAM+ version 4.0 are direct incorporation of unconfined overpressure into the QRA calculations and modification of the models for cryogenic liquid flow through an orifice. In QRA mode, the user no longer needs to input peak overpressure and impulse values that were calculated separately; rather, the unconfined overpressure is estimated for the given system inputs, leak size, and occupant location. The orifice flow model now solves for the maximum mass flux through the orifice at constant entropy while conserving energy, which does not require a direct speed of sound calculation. This does not affect the mass flow for all-gaseous releases; the method results in the same speed of sound for choked flow. However, this method does result in a higher (and more realistic) mass flow rate for a given leak size for liquid releases than was previously calculated.
The HyRAM+ software toolkit provides a basis for conducting quantitative risk assessment and consequence modeling for hydrogen, natural gas, and autogas systems. HyRAM+ is designed to facilitate the use of state-of-the-art models to conduct robust, repeatable assessments of safety, hazards, and risk. HyRAM+ integrates deterministic and probabilistic models for quantifying leak sizes and rates, predicting physical effects, characterizing hazards (thermal effects from jet fires, overpressure effects from delayed ignition), and assessing impacts on people. HyRAM+ is developed at Sandia National Laboratories to support the development and revision of national and international codes and standards, and to provide developed models in a publicly-accessible toolkit usable by all stakeholders. This document provides a description of the methodology and models contained in HyRAM+ version 5.0. The most significant change for HyRAM+ version 5.0 from HyRAM+ version 4.1 is the ability to model blends of different fuels. HyRAM+ was previously only suitable for use with hydrogen, methane, or propane, with users having the ability to use methane as a proxy for natural gas and propane as a proxy for autogas/liquefied petroleum gas. In version 5.0, real natural gas or autogas compositions can be modeled as the fuel, or even blends of natural gas with hydrogen. These blends can be used in the standalone physics models, but not yet in the quantitative risk assessment mode of HyRAM+.