Results for “surface conditioning” — Page 16

NASA NTRS1983

Ocean experiments and remotely sensed images of chemically dispersed oil spills

A series of experiments was performed at sea where the effectiveness of dispersants applied from a helicopter was tested on fresh and weathered crude oils released from a surface research vessel. In conjunction with these experiments, remote sensing measurements using an array of airborne optical and microwave sensors were performed in order to aid in the interpretation of the dispersant effectiveness and to obtain quantitative images of oil on the sea under controlled conditions. Surface oil thickness and volume are inferred from airborne measurements using a dual-channel microwave imaging radiometer, aerial color photography, and an airborne oceanographic lidar. The remotely sensed measurements are compared with point sampled data obtained using a research vessel. The mass balance computations of surface versus subsurface oil volume using remotely sensed and point sampled data are consistent with each other and with the volumes of oil released. Data collected by the several techniques concur in indicating that, for the oils used and under the sea conditions encountered, the dispersant and application method are primarily useful when applied to fresh oil.

Croswell, W. F.↗

NASA NTRS1977

Three-dimensional low Reynolds number flows with a free surface

The two-dimensional leveling problem (Degani, Gutfinger, 1976) is extended to three dimensions in the case where the flow Re number is very low and attention is paid to the free surface boundary condition with surface tension effects included. The no-slip boundary condition on the wall is observed. The numerical solution falls back on the Marker and Cell (MAC) method (Harlow and Welch, 1965) with the computation region divided into a finite number of stationary rectangular cells (or boxes in the 3-D case) and fluid flow traverses the cells (or boxes).

Degani, D.↗

NASA NTRS1990

Ultrasonic techniques for aircraft ice accretion measurement

Results of tests to measure ice growth in natural (flight) and artificial (icing wind tunnel) icing conditions are presented. Ice thickness is measured using an ultrasonic pulse-echo technique. Two icing regimes, wet and dry ice growth, are identified and the unique ultrasonic signal characteristics associated with these different types of ice growth are described. Ultrasonic measurements of ice growth on cylinders and airfoils exposed to artificial and natural icing conditions are presented. An accuracy of plus or minus 0.5 mm is achieved for ice thickness measurement using the pulse-echo technique. The performance of two-probe type ice detectors is compared to the surface mounted ultrasonic system. The ultrasonically measured ice accretion rates and ice surface condition (wet or dry) are used to compare the heat transfer characteristics for flight and icing wind tunnel environments. In general the heat transfer coefficient is inferred to be higher in the wind tunnel environment, not likely due to higher freestream turbulence levels. Finally, preliminary results of tests to measure ice growth on airfoil using an array of ultrasonic transducers are described. Ice profiles obtained during flight in natural icing conditions are shown and compared with mechanical and stereo image measurements.

Hansman, R. John, Jr.↗

NASA NTRS2012

Evaluation of Moderate-Resolution Imaging Spectroradiometer (MODIS) Snow Albedo Product (MCD43A) over Tundra

This study assesses the MODIS standard Bidirectional Reflectance Distribution Function (BRDF)/Albedo product, and the daily Direct Broadcast BRDF/Albedo algorithm at tundra locations under large solar zenith angles and high anisotropic diffuse illumination and multiple scattering conditions. These products generally agree with ground-based albedo measurements during the snow cover period when the Solar Zenith Angle (SZA) is less than 70deg. An integrated validation strategy, including analysis of the representativeness of the surface heterogeneity, is performed to decide whether direct comparisons between field measurements and 500- m satellite products were appropriate or if the scaling of finer spatial resolution airborne or spaceborne data was necessary. Results indicate that the Root Mean Square Errors (RMSEs) are less than 0.047 during the snow covered periods for all MCD43 albedo products at several Alaskan tundra areas. The MCD43 1- day daily albedo product is particularly well suited to capture the rapidly changing surface conditions during the spring snow melt. Results also show that a full expression of the blue sky albedo is necessary at these large SZA snow covered areas because of the effects of anisotropic diffuse illumination and multiple scattering. In tundra locations with dark residue as a result of fire, the MODIS albedo values are lower than those at the unburned site from the start of snowmelt.

Wang, Zhuosen↗

NASA NTRS2001

Surface Salinity Variability in the North Atlantic During Recent Decades

The sea surface salinity (SSS) variability in the North Atlantic is investigated using numerical model simulations for the last 50 years based on atmospheric forcing variability from Comprehensive Atmosphere Ocean Data Set (COADS) and National Center for Environmental Prediction / National Center for Atmospheric Research (NCEP/NCAR) Reanalysis. The largest interannual and longer term variability occurs in two regions: the Labrador Sea and the North Equatorial Countercurrent (NECC) region. In both regions the seasonality of the surface salinity variability is prominent with the maximum standard deviation occurring in the summer/fall period. In the Labrador Sea the summer SSS anomalies far exceed those of wintertime in amplitude. The interannual SSS variability in the subpolar gyre can be attributed to two factors: excess ice melt and heat flux (i.e. deep mixing) variations. On the other hand, heat flux variability can also lead to meridional overturning changes on decadal time scales such that weak overturning is manifested in fresh surface conditions in the subpolar gyre. The overturning changes also influence the NECC region SSS variability. Moreover, the subpolar freshening events are expected to occur during the negative phase of North Atlantic Oscillation which is associated with a weak wintertime surface heat loss in the subpolar gyre. No excess sea ice melt or precipitation is necessary for the formation of the fresh anomalies, because with the lack of wide-spread deep mixing, the fresh water that would be expected based on climatology, would accumulate at the surface. Thus, the fresh water 'conveyor' in the Atlantic operates via the overturning circulation such that deep mixing inserts fresh water while removing heat from the water column.

Haekkinen, Sirpa↗

NASA NTRS2019

Assessment of a One-Dimensional Finite Element Charring Ablation Material Response Model for Phenolic-Impregnated Carbon Ablator

In this study, mathematical formulations to model charring ablation problems were numerically implemented using finite element analysis (FEA) with ABAQUS, which account for the material decomposition and progressive surface removal in the heat conduction and the surface energy balance equations. FEA was performed for a one-dimensional model to predict the temperature and ablation histories of a phenolic-impregnated carbon ablator sample (i.e., a common heat shield material for hypersonic vehicles and spacecraft) subjected to oxy-acetylene torch flame (i.e., 0.8 SLPM acetylene gas to 2.7 SLPM oxygen gas). The recovery enthalpy and convective heat transfer coefficient for the ablation model were calculated based on gas compositions and two assumed surface conditions (i.e., equilibrium and frozen). Simulations using the calculated recovery enthalpy and convective heat transfer coefficient resulted in a recession rate of 6.38 times (equilibrium) and 14.08 times (frozen) higher than the experimental data, despite fair agreement of the surface temperature. In addition, the effect of the heat transfer coefficient was investigated through a steady-state ablation analysis. The results of the analysis indicate that there is not one single value for the heat transfer coefficient that would allow the prediction to match both measured recession rate and surface temperature. Possible reasons for such an inconsistency are provided and discussed.

Thermal Protection System↗

NASA NTRS2020

Experimental Heat Transfer Supporting Simulated Water Well Performance on Mars

Favorable indications of massive quantities of water on Mars have initiated studies of potential changes to human Mars missions. Using a technique known as a Rodriguez Well to melt the ice, store the resulting water in a subsurface ice cavity until needed, and then pump water to the surface for use is one potential means to effect these changes. A computer simulation of the Rodriguez Well in a terrestrial environment is one of the engineering tools being used to characterize the performance of this type of well on Mars. An experiment at the NASA Johnson Space Center is gathering data for convective heat transfer and evaporation rates at Mars surface conditions so that this computer simulation can be properly modified to predict performance on Mars. While quantitative results await processing, tests have indicated that a pool of water can be maintained at 1°C to 2° C while at Mars surface temperatures and pressures.

Hoffman, Stephen J.↗

NASA NTRSDate not supplied

Mars Water Well Performance: Experimental Heat Transfer Results Supporting Simulations

Favorable indications of massive quantities of water on Mars have initiated studies of potential changes to human Mars missions. Using a technique known as a Rodriguez Well to melt the ice, store the resulting water in a subsurface ice cavity until needed, and then pump water to the surface for use is one potential means to effect these changes. A computer simulation of the Rodriguez Well in a terrestrial environment is one of the engineering tools being used to characterize the performance of this type of well on Mars. An experiment at the NASA Johnson Space Center is gathering data for convective heat transfer and evaporation rates at Mars surface conditions so that this computer simulation can be properly modified to predict performance on Mars. While quantitative results await processing, tests have indicated that a pool of water can be maintained at 1°C to 2° C while at Mars surface temperatures and pressures.

Mars↗

NASA NTRSDate not supplied

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗

NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗

NASA NTRS2002

Life Beneath Glacial Ice - Earth(!) Mars(?) Europa(?)

We are investigating a set of cold springs that deposit sulfur and carbonate minerals on the surface of a Canadian arctic glacier. The spring waters and mineral deposits contain microorganisms, as well as clear evidence that biological processes mediate subglacial chemistry, mineralogy, and isotope fractionation . The formation of native sulphur and associated deposits are related to bacterially mediated reduction and oxidation of sulphur below the glacier. A non-volcanic, topography driven geothermal system, harboring a microbiological community, operates in an extremely cold environment and discharges through solid ice. Microbial life can thus exist in isolated geothermal refuges despite long-term subfreezing surface conditions. Earth history includes several periods of essentially total glaciation. lee in the near subsurface of Mars may have discharged liquid water in the recent past Cracks in the ice crust of Europa have apparently allowed the release of water to the surface. Chemolithotrophic bacteria, such as those in the Canadian springs, could have survived beneath the ice of "Snowball Earth", and life forms with similar characteristics might exist beneath the ice of Mars or Europa. Discharges of water from such refuges may have brought to the surface living microbes, as well as longlasting chemical, mineralogical, and isotopic indications of subsurface life.

Allen, Carlton C.↗

NASA NTRS1965

Boundary conditions at the surface of contact between an ionized gas and a solid <o granichnykh usloviyakh na poverkhnosti kontakta ionizovannyy gaz-tverdoye telo<

Boundary conditions at surface of contact between ionized gas and electrode material

IONIZED GAS↗

NASA NTRS2017

The Effect of Entrainment Through Atmospheric Boundary Layer Growth on Observed and Modeled Surface Ozone in the Colorado Front Range

Ozone concentrations at the Earth's surface are controlled by meteorological and chemical processes and are a function of advection, entrainment, deposition, and net chemical production/loss. The relative contributions of these processes vary in time and space. Understanding the relative importance of these processes controlling surface ozone concentrations is an essential component for designing effective regulatory strategies. Here we focus on the diurnal cycle of entrainment through atmospheric boundary layer (ABL) growth in the Colorado Front Range. Aircraft soundings and surface observations collected in July/August 2014 during the DISCOVER-AQ/FRAPPÉ (Deriving Information on Surface conditions from Column and Vertically Resolved Observations Relevant to Air Quality/Front Range Air Pollution and Photochemistry Éxperiment) campaigns and equivalent data simulated by a regional chemical transport model are analyzed. Entrainment through ABL growth is most important in the early morning, fumigating the surface at a rate of ~5 ppbv/h. The fumigation effect weakens near noon and changes sign to become a small dilution effect in the afternoon on the order of -1 ppbv/h. The chemical transport model WRF-Chem (Weather Research and Forecasting Model with chemistry) underestimates ozone at all altitudes during this study on the order of 10-15 ppbv. The entrainment through ABL growth is overestimated by the model in the order of 0.6-0.8 ppbv/h. This results from differences in boundary layer growth in the morning and ozone concentration jump across the ABL top in the afternoon. This implicates stronger modeled fumigation in the morning and weaker modeled dilution after 11:00 LT.

Entrainment through ABL Growth↗

NASA NTRS1976

Surface studies of barium and barium oxide on tungsten and its application to understanding the mechanism of operation of an impregnated tungsten cathode

Surface studies have been made of multilayer and monolayer films of barium and barium oxide on a tungsten substrate. The purpose of the investigation was to synthesize the surface conditions that exist on an activated impregnated tungsten cathode and obtain a better understanding of the mechanism of operation of such cathodes. The techniques employed in these measurements were Auger spectroscopy and work-function measurements. The results of this study show that the surface of an impregnated cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on oxidized tungsten by evaluating Auger spectra and work-function measurements. Data obtained from desorption studies of barium monolayers on a tungsten substrate in conjunction with Auger and work-function results have been interpreted to show that throughout most of its life an impreganated cathode has a partial monolayer, rather than a monolayer, of barium on its surface.

Forman, R.↗

NASA NTRSDate not supplied

NASA Lunar Surface Innovation Initiative: Ensuring a Cohesive, Executable Strategy for Technology Development

Establishing a sustainable human presence on the Moon allows NASA to develop and test new approaches, technologies, and systems that will enable us to function in other, more challenging environments. The Lunar Surface Innovation Initiative (LSII) was established in 2019 and has evolved into a key agency asset to spur technology development and provide risk reduction for lunar surface system development and flight demonstrations. LSII coordinates activities implemented through a combination of in-house activities, competitive programs, and public-private partnerships to create transformative technologies needed for lunar surface exploration. This paper will outline the LSII model used to develop a technology pipeline that will retire the primary technology hurdles in six capability areas. In-situ resource utilization technologies for collecting, processing, storing, and using material found or manufactured on the Moon. Surface power technologies that provide the capability for sustainable, continuous power throughout the day and night for lunar missions. Dust mitigation strategies that diminish lunar dust hazards on lunar surface systems such as cameras, solar panels, space suits, habitats, and instrumentation. Extreme environments technologies that enable systems to operate throughout the full range of lunar surface conditions, including lunar noon (up to 150 at the equator), night (down to - 180 at the equator), multiple day/night cycles, and in permanently shadowed regions (down to -250). Extreme access technologies that enable humans or robotic systems to access, navigate, and explore previously inaccessible lunar surface or subsurface areas. Excavation and construction technologies that will allow affordable, autonomous manufacturing or construction. We outline key results, including milestones and achievements related to the capability areas and outcomes from partnerships with the commercial sector. A key tenet of the LSII is the Lunar Surface Innovation Consortium (LSIC), a collaboration across industry, academia, and government to successfully develop the transformative capabilities for lunar surface exploration. LSIC provides a forum for NASA to communicate technological requirements, needs, and opportunities and for the community to share existing capabilities and identify critical gaps with NASA. By working side by side with commercial enterprises and our international partners, NASA is able to combine the knowledge and expertise needed to explore the lunar surface and make technical advances that will feed technological and economic growth. Since its inception, LSII has engaged over 600 organizations across the United States and 46 countries to shape the technologies and systems needed to explore the lunar surface and stimulate a lunar surface economy.

lunar, lunar surface, technology development, ISRU↗

NASA NTRSDate not supplied

NASA Lunar Surface Innovation Initiative: Ensuring a Cohesive, Executable Strategy for Technology

Establishing a sustainable human presence on the Moon allows NASA to develop and test new approaches, technologies, and systems that will enable us to function in other, more challenging environments. The Lunar Surface Innovation Initiative (LSII) was established in 2019 and has evolved into a key agency asset to spur technology development and provide risk reduction for lunar surface system development and flight demonstrations. LSII coordinates activities implemented through a combination of in-house activities, competitive programs, and public-private partnerships to create transformative technologies needed for lunar surface exploration. This paper will outline the LSII model used to develop a technology pipeline that will retire the primary technology hurdles in six capability areas. In-situ resource utilization technologies for collecting, processing, storing, and using material found or manufactured on the Moon. Surface power technologies that provide the capability for sustainable, continuous power throughout the day and night for lunar missions. Dust mitigation strategies that diminish lunar dust hazards on lunar surface systems such as cameras, solar panels, space suits, habitats, and instrumentation. Extreme environments technologies that enable systems to operate throughout the full range of lunar surface conditions, including lunar noon (up to 150 at the equator), night (down to - 180 at the equator), multiple day/night cycles, and in permanently shadowed regions (down to -250). Extreme access technologies that enable humans or robotic systems to access, navigate, and explore previously inaccessible lunar surface or subsurface areas. Excavation and construction technologies that will allow affordable, autonomous manufacturing or construction. We outline key results, including milestones and achievements related to the capability areas and outcomes from partnerships with the commercial sector. A key tenet of the LSII is the Lunar Surface Innovation Consortium (LSIC), a collaboration across industry, academia, and government to successfully develop the transformative capabilities for lunar surface exploration. LSIC provides a forum for NASA to communicate technological requirements, needs, and opportunities and for the community to share existing capabilities and identify critical gaps with NASA. By working side by side with commercial enterprises and our international partners, NASA is able to combine the knowledge and expertise needed to explore the lunar surface and make technical advances that will feed technological and economic growth. Since its inception, LSII has engaged over 600 organizations across the United States and 46 countries to shape the technologies and systems needed to explore the lunar surface and stimulate a lunar surface economy.

Lunar↗

NASA NTRS1975

Ditching investigation of a 1/20-scale model of the space shuttle orbiter

The ditching characteristics of the space shuttle orbiter were examined. Tests were made with a 1/20-scale model in order to determine behavior patterns and accelerations imparted to the ditching vehicle. Ditchings were made with different configurations of weight and gear position. Also the effects of different water surface conditions were investigated. The test results indicated that the favorable conditions for ditching usually involve a landing attitude of 12 deg. Smooth ditchings were always associated with the landing-gear retracted and never with the landing-gear extended. Higher landing mass, generally, resulted in higher acceleration values in both the longitudinal and normal directions. Surface waves tend to increase the pitch accelerations but at the same time tend to reduce the accelerations in the longitudinal and normal directions.

Thomas, W. L.↗

NASA NTRS1981

LANDSAT data for coastal zone management

The lack of adequate, current data on land and water surface conditions in New Jersey led to the search for better data collections and analysis techniques. Four-channel MSS data of Cape May County and access to the OSER computer interpretation system were provided by NASA. The spectral resolution of the data was tested and a surface cover map was produced by going through the steps of supervised classification. Topics covered include classification; change detection and improvement of spectral and spatial resolution; merging LANDSAT and map data; and potential applications for New Jersey.

Mckenzie, S.↗