Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “statistical analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

WE-DE-201-02: A Statistical Analysis Tool for Plan Quality Verification in HDR Brachytherapy Forward Planning for Cervix Cancer

Purpose: High Dose Rate (HDR) brachytherapy forward planning is principally an iterative process; hence, plan quality is affected by planners’ experiences and limited planning time. Thus, this may lead to sporadic errors and inconsistencies in planning. A statistical tool based on previous approved clinical treatment plans would help to maintain the consistency of planning quality and improve the efficiency of second checking. Methods: An independent dose calculation tool was developed from commercial software. Thirty-three previously approved cervical HDR plans with the same prescription dose (550cGy), applicator type, and treatment protocol were examined, and ICRU defined reference point doses (bladder, vaginal mucosa, rectum, and points A/B) along with dwell times were collected. Dose calculation tool then calculated appropriate range with a 95% confidence interval for each parameter obtained, which would be used as the benchmark for evaluation of those parameters in future HDR treatment plans. Model quality was verified using five randomly selected approved plans from the same dataset. Results: Dose variations appears to be larger at the reference point of bladder and mucosa as compared with rectum. Most reference point doses from verification plans fell between the predicted range, except the doses of two points of rectum and two points of reference position A (owing to rectal anatomical variations & clinical adjustment in prescription points, respectively). Similar results were obtained for tandem and ring dwell times despite relatively larger uncertainties. Conclusion: This statistical tool provides an insight into clinically acceptable range of cervical HDR plans, which could be useful in plan checking and identifying potential planning errors, thus improving the consistency of plan quality.

60 APPLIED LIFE SCIENCES↗

Use of Statistical Analysis of Acoustic Emission Data on Carbon-Epoxy COPV Materials-of-Construction for Enhanced Felicity Ratio Onset Determination

Broadband modal acoustic emission (AE) data were acquired during intermittent load hold tensile test profiles on Toray T1000G carbon fiber-reinforced epoxy (C/Ep) single tow specimens. A novel trend seeking statistical method to determine the onset of significant AE was developed, resulting in more linear decreases in the Felicity ratio (FR) with load, potentially leading to more accurate failure prediction. The method developed uses an exponentially weighted moving average (EWMA) control chart. Comparison of the EWMA with previously used FR onset methods, namely the discrete (n), mean (n (raised bar)), normalized (n%) and normalized mean (n(raised bar)%) methods, revealed the EWMA method yields more consistently linear FR versus load relationships between specimens. Other findings include a correlation between AE data richness and FR linearity based on the FR methods discussed in this paper, and evidence of premature failure at lower than expected loads. Application of the EWMA method should be extended to other composite materials and, eventually, composite components such as composite overwrapped pressure vessels. Furthermore, future experiments should attempt to uncover the factors responsible for infant mortality in C/Ep strands.

Abraham, Arick Reed A.↗

Nearfield Summary and Statistical Analysis of the Second AIAA Sonic Boom Prediction Workshop

A summary is provided for the Second AIAA Sonic Boom Workshop held 8-9 January 2017 in conjunction with AIAA SciTech 2017. The workshop used three required models of increasing complexity: an axisymmetric body, a wing body, and a complete configuration with flow-through nacelle. An optional complete configuration with propulsion boundary conditions is also provided. These models are designed with similar nearfield signatures to isolate geometry and shock/expansion interaction effects. Eleven international participant groups submitted nearfield signatures with forces, pitching moment, and iterative convergence norms. Statistics and grid convergence of these nearfield signatures are presented. These submissions are propagated to the ground, and noise levels are computed. This allows the grid convergence and the statistical distribution of a noise level to be computed. While progress is documented since the first workshop, improvement to the analysis methods for a possible subsequent workshop are provided. The complete configuration with flow-through nacelle showed the most dramatic improvement between the two workshops. The current workshop cases are more relevant to vehicles with lower loudness and have the potential for lower annoyance than the first workshop cases. The models for this workshop with quieter ground noise levels than the first workshop exposed weaknesses in analysis, particularly in convective discretization.

Park, Michael A.↗

Nearfield Summary and Statistical Analysis of the Second AIAA Sonic Boom PredictionWorkshop

A summary is provided for the Second AIAA Sonic Boom Workshop held 8–9 January 2017 in conjunction with AIAA SciTech 2017. The workshop used three required models of increasing complexity: an axisymmetric body, a wing body, and a complete configuration with flow-through nacelle. An optional complete configuration with propulsion boundary conditions is also provided. These models are designed with similar nearfield signatures to isolate geometry and shock/expansion interaction e ects. Eleven international participant groups submitted nearfield signatures with forces, pitching moment, and iterative convergence norms. Statistics and grid convergence of these nearfield signatures are presented. These submissions are propagated to the ground, and noise levels are computed. This allows the grid convergence and the statistical distribution of a noise level to be computed. While progress is documented since the first workshop, improvement to the analysis methods for a possible subsequent workshop are provided. The complete configuration with flow-through nacelle showed the most dramatic improvement between the two workshops. The current workshop cases are more relevant to vehicles with lower loudness and have the potential for lower annoyance than the first workshop cases. The models for this workshop with quieter ground noise levels than the first workshop exposed weaknesses in analysis, particularly in convective discretization.

Park, Michael A.↗

Statistical analysis of direct-strike lightning data (1980 to 1982)

Electromagnetic measurements are being made during direct lightning strikes by NASA Langley Center using a specially instrumented F-106B aircraft. The research is to aid refinement, characterization, and understanding of the lightning-aircraft interaction process and the lightning hazards to aircraft. Statistical methods are applied to characterize some aspects of the lightning data obtained from 176 strikes to the aircraft. Specific attention is given to the problem of estimating the upper extreme quantiles of the distributions of peak-to-peak values for currents and rates of change in the magnetic and flux densities. A formal treatment via a general location-scale family of models allows the estimation method to be adapted to the realized shapes the distributions. The shapes are examined by probability plotting methods.

Lee, L. D.↗

Statistical analysis of censored motion sickness latency data using the two-parameter Weibull distribution

The suitability of the two-parameter Weibull distribution for describing highly censored cat motion sickness latency data was evaluated by estimating the parameters with the maximum likelihood method and testing for goodness of fit with the Kolmogorov-Smirnov statistic. A procedure for determining confidence levels and testing for significance of the difference between Weibull parameters is described. Computer programs for these procedures may be obtained from an archival source.

Park, Won J.↗

Statistical analysis of the Nb 3 Sn strand production for the ITER toroidal field coils

The ITER toroidal field (TF) strand procurement initiated the largest Nb 3 Sn superconducting strand production hitherto. The industrial-scale production started in Japan in 2008 and finished in summer 2015. Six ITER partners (so-called Domestic Agencies, or DAs) are in charge of the procurement and involved eight different strand suppliers all over the world, of which four are using the bronze route (BR) process and four the internal-tin (IT) process. In total more than 500 tons have been produced including excess material covering losses during the conductor manufacturing process, in particular the cabling. The procurement is based on a functional specification where the main strand requirements like critical current, hysteresis losses, Cu ratio and residual resistance ratio are specified but not the strand production process or layout. We introduce the analysis on the data acquired during the quality control (QC) process that was carried out to ensure the same conductor performance requirements are met by the different strand suppliers regardless of strand design. The strand QC is based on 100% billet testing and on applying statistical process control (SPC) limits. Throughout the production, samples adjacent to the strand pieces tested by the suppliers are cross-checked ('verified') by their respective DAs reference labs. The level of verification was lowered from 100% at the beginning of the procurement progressively to approximately 25% during the final phase of production. Based on the complete dataset of the TF strand production, an analysis of the SPC limits of the critical strand parameters is made and the related process capability indices are calculated. In view of the large-scale production and costs, key manufacturing parameters such as billet yield, number of breakages and piece-length distribution are also discussed. Furthermore, the results are compared among all the strand suppliers, focusing on the difference between BR and IT processes. Following the completion of the largest Nb 3 Sn strand production, our experience gained from monitoring the execution of the QC activities and from auditing the results from the measurements is summarised for future superconducting strand material procurement activities.

Vostner, A.↗

Statistical Analysis of Hubble /WFC3 Transit Spectroscopy of Extrasolar Planets

Transmission spectroscopy provides a window to study exoplanetary atmospheres, but that window is fogged by clouds and hazes. Clouds and haze introduce a degeneracy between the strength of gaseous absorption features and planetary physical parameters such as abundances. One way to break that degeneracy is via statistical studies. We collect all published HST /WFC3 transit spectra for 1.1–1.65 μ m water vapor absorption and perform a statistical study on potential correlations between the water absorption feature and planetary parameters. We fit the observed spectra with a template calculated for each planet using the Exo-transmit code. We express the magnitude of the water absorption in scale heights, thereby removing the known dependence on temperature, surface gravity, and mean molecular weight. We find that the absorption in scale heights has a positive baseline correlation with planetary equilibrium temperature; our hypothesis is that decreasing cloud condensation with increasing temperature is responsible for this baseline slope. However, the observed sample is also intrinsically degenerate in the sense that equilibrium temperature correlates with planetary mass. We compile the distribution of absorption in scale heights, and we find that this distribution is closer to log-normal than Gaussian. However, we also find that the distribution of equilibrium temperatures for the observed planets is similarly log-normal. This indicates that the absorption values are affected by observational bias, whereby observers have not yet targeted a sufficient sample of the hottest planets.

79 ASTRONOMY AND ASTROPHYSICS↗

Skylab 2 ground winds data reduction and statistical analysis

A ground winds test was conducted on the Skylab 2 spacecraft in a subsonic wind tunnel and the results were tape recorded for analysis. The data reduction system used to analyze the tapes for full scale, first and second mode bending moments, or acceleration plots versus dynamic pressure or wind velocity is explained. Portions of the Skylab 2 tape data were analyzed statistically in the form of power spectral densities, autocorrelations, and cross correlations to introduce a concept of using system response decay as a measure of linear system damping.

Source record↗

ON THE STATISTICAL ANALYSIS OF X-RAY POLARIZATION MEASUREMENTS

In many polarimetry applications, including observations in the X-ray band, the measurement of a polarization signal can be reduced to the detection and quantification of a deviation from uniformity of a distribution of measured angles of the form A + Bcos {sup 2}({phi} - {phi}{sub 0}) (0 < {phi} < {pi}). We explore the statistics of such polarization measurements using Monte Carlo simulations and {chi}{sup 2} fitting methods. We compare our results to those derived using the traditional probability density used to characterize polarization measurements and quantify how they deviate as the intrinsic modulation amplitude grows. We derive relations for the number of counts required to reach a given detection level (parameterized by {beta} the ''number of {sigma}'s'' of the measurement) appropriate for measuring the modulation amplitude a by itself (single interesting parameter case) or jointly with the position angle {phi} (two interesting parameters case). We show that for the former case, when the intrinsic amplitude is equal to the well-known minimum detectable polarization, (MDP) it is, on average, detected at the 3{sigma} level. For the latter case, when one requires a joint measurement at the same confidence level, then more counts are needed than what was required to achieve the MDP level. This additional factor is amplitude-dependent, but is Almost-Equal-To 2.2 for intrinsic amplitudes less than about 20%. It decreases slowly with amplitude and is Almost-Equal-To 1.8 when the amplitude is 50%. We find that the position angle uncertainty at 1{sigma} confidence is well described by the relation {sigma}{sub {phi}} = 28. Degree-Sign 5/{beta}.

79 ASTRONOMY AND ASTROPHYSICS↗

Statistical analysis of the modal properties of large structural systems.

A theory is developed to predict eigenvalue and eigenvector uncertainty in large dynamic models. The uncertainty is based on physical property uncertainty and should not be confused with numerical roundoff, although the method can be extended to include the latter. The theory, when implemented on a computer, is used to analyze the uncertainties in frequencies and mode shapes based on uncertainties in mass, stiffness, modulus of elasticity, etc. The method incorporates a linear statistical model which is quite adequate for handling property uncertainties of 10% or more. The model is not limited to small systems but uses certain statistical assumptions as well as selective matrix manipulations to keep the size of all matrix operations to within the number of degrees of freedom of the system. Examples are given for two longitudinal vibration problems, and the results are supported by a Monte Carlo analysis.

Collins, J. D.↗

Combining Inspection and Unattended Monitoring: Statistical Analysis of Timely Detection

Process monitoring traditionally relies on facility operator measurements. New concepts for future inspection regimes include inspectorate-owned systems that enable unattended monitoring (UM) of all declared material flow \cite{smith_potential}. If such systems can be established as viable alternatives, they may provide an important new capability: a true inspector's estimate of MUF that can achieve the efficiency and effectiveness goals outlined by the IAEA. A rigorous statistical framework for comparing traditional and new methodologies is needed to evaluate this potential and enable inspectorates to optimally balance UM and sampling in the context of timely detection and cost constraints. Recognizing that these are only two among a wide range of safeguards activities that support mass balance evaluation to detect missing material, this paper compares UM to traditional safeguards sampling in terms of detection probabilities as a function of time based on simplistic material loss scenarios, and shows how the detection probabilities can be rather easily combined. Using this approach can help enable tradeoff analysis and optimal resource allocation.

international safeguards↗

Statistical analysis of displacement damage in small devices from neutron and ion irradiation

Modern semiconductor devices, such as gate-all-around nanosheet field-effect transistors (GAA NS FETs), are smaller than displacement damage cascades from fission neutrons. In this regime, device failure may occur through low-probability single events, rather than by parametric degradation previously seen in larger devices. Here, we present a statistical model that predicts the probability of a damage event in a small device and the probability distribution of the magnitude, i.e., number of displacements within the device, from each event. The model is developed first for neutron irradiation and then for energetic ion irradiation. The model is consistent with results from recent experiments in which lithium-ion irradiation produced stepwise increases in subthreshold current in GAA NS FETs.

Wampler, W. R.↗

A Statistical Analysis of Impact Ice Adhesion Strength Data Acquired with a Modified Lap Joint Test

Numerous methodologies have been utilized to measure the adhesion strength of impact ice, and the data reported in the literature varies significantly from method to method. In order to initiate an investigation to determine the cause of this disparity, a lap-joint shear test methodology that was recently developed was utilized in the Icing Research Tunnel at the NASA Glenn Research Center. Data was obtained while varying the temperature, test section velocity, liquid water content, and cloud droplet median volumetric diameter, among other parameters, over five campaigns. A new data set acquired using this new test method is presented. The results are analyzed with standard statistical methodologies and demonstrate a strong correlation between the apparent adhesion strength of ice and temperature, annealing time, and heating time. Observations during the test and analysis of the results suggest the presence of large residual stresses in the samples, which is in agreement with prior work. Due to the nature of the test methodology, and all known ice adhesion test methodologies, the measured, or apparent, adhesion strength is geometry dependent, a fact emphasized by the results presented here. The data was organized both cumulatively and independently by result code. Trends in the data are discussed in the context of causal physical mechanisms. The data shows the apparent adhesion strength was not linear with temperature, liquid water content, annealing time, and other variables. Short-term heating of the samples was shown to have negligible effect, and the apparent adhesion strength had a flat trend with velocity.

Ice Adhesion↗

Landing Site Dispersion Analysis and Statistical Assessment for the Mars Phoenix Lander

The Mars Phoenix Lander launched on August 4, 2007 and successfully landed on Mars 10 months later on May 25, 2008. Landing ellipse predicts and hazard maps were key in selecting safe surface targets for Phoenix. Hazard maps were based on terrain slopes, geomorphology maps and automated rock counts of MRO's High Resolution Imaging Science Experiment (HiRISE) images. The expected landing dispersion which led to the selection of Phoenix's surface target is discussed as well as the actual landing dispersion predicts determined during operations in the weeks, days, and hours before landing. A statistical assessment of these dispersions is performed, comparing the actual landing-safety probabilities to criteria levied by the project. Also discussed are applications for this statistical analysis which were used by the Phoenix project. These include using the statistical analysis used to verify the effectiveness of a pre-planned maneuver menu and calculating the probability of future maneuvers.

Bonfiglio, Eugene P.↗

On the Statistical Analysis of X-ray Polarization Measurements

In many polarimetry applications, including observations in the X-ray band, the measurement of a polarization signal can be reduced to the detection and quantification of a deviation from uniformity of a distribution of measured angles of the form alpha plus beta cosine (exp 2)(phi - phi(sub 0) (0 (is) less than phi is less than pi). We explore the statistics of such polarization measurements using both Monte Carlo simulations as well as analytic calculations based on the appropriate probability distributions. We derive relations for the number of counts required to reach a given detection level (parameterized by beta the "number of sigma's" of the measurement) appropriate for measuring the modulation amplitude alpha by itself (single interesting parameter case) or jointly with the position angle phi (two interesting parameters case). We show that for the former case when the intrinsic amplitude is equal to the well known minimum detectable polarization (MDP) it is, on average, detected at the 3sigma level. For the latter case, when one requires a joint measurement at the same confidence level, then more counts are needed, by a factor of approximately equal to 2.2, than that required to achieve the MDP level. We find that the position angle uncertainty at 1sigma confidence is well described by the relation sigma(sub pi) equals 28.5(degrees) divided by beta.

Strohmayer, T. E.↗

A Statistical Analysis of Loop-Top Motion in Solar Limb Flares

Previous studies of hot, thermal solar flare loops imaged with the Ramaty High Energy Solar Spectroscopic Imager (RHESSI) have identified several flares for which the loop top shrinks downward early in the impulsive phase and then expands upward later in the impulsive phase (Sui & Holman 2003; Sui, Holman & Dennis 2004; Veronig et al. 2005). This early downward motion is not predicted by flare models. We study a statistical sample of RHESSI flares to assess how common this evolution is and to better characterize it. In a sample of 88 flares near the solar lin$ that show identifiable loop structure in RHESSI images, 66% (58 flares) showed downward loop-top motion followed by upward motion. We therefore conclude that the early downward motion is a frequent characteristic of flare loops. We obtain the distribution of the timing of the change from downward to upward motion relative to flare start and peak times. We also obtain the distributions of downward and upward speeds.

Holman, Gordon D.↗