Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pattern dependence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Interaction between corrosion crack width and steel loss in RC beams corroded under load

This paper presents results and discussions on an experimental study conducted to relate the rate of widening of corrosion cracks with the pattern of corrosion cracks as well as the level of steel corrosion for RC beams (153 x 254 x 3000 mm) that were corroded whilst subjected to varying levels of sustained loads. Steel corrosion was limited to the tensile reinforcement and to a length of 700 mm at the centre of the beams. The rate of widening of corrosion cracks as well as strains on uncracked faces of RC beams was constantly monitored during the corrosion process, along the corrosion region and along other potential cracking faces of beams using a demec gauge. The distribution of the gravimetric mass loss of steel along the corrosion region was measured at the end of the corrosion process. The results obtained showed that: the rate of widening of each corrosion crack is dependent on the overall pattern of the cracks whilst the rate of corrosion is independent of the pattern of corrosion cracks. A mass loss of steel of 1% was found to induce a corrosion crack width of about 0.04 mm.

36 MATERIALS SCIENCE↗

Interplay of hidden orbital order and superconductivity in CeCoIn5

Abstract Visualizing atomic-orbital degrees of freedom is a frontier challenge in scanned microscopy. Some types of orbital order are virtually imperceptible to normal scattering techniques because they do not reduce the overall crystal lattice symmetry. A good example is d xz / d yz (π,π) orbital order in tetragonal lattices. For enhanced detectability, here we consider the quasiparticle scattering interference (QPI) signature of such (π,π) orbital order in both normal and superconducting phases. The theory reveals that sublattice-specific QPI signatures generated by the orbital order should emerge strongly in the superconducting phase. Sublattice-resolved QPI visualization in superconducting CeCoIn 5 then reveals two orthogonal QPI patterns at lattice-substitutional impurity atoms. We analyze the energy dependence of these two orthogonal QPI patterns and find the intensity peaked near E = 0, as predicted when such (π,π) orbital order is intertwined with d -wave superconductivity. Sublattice-resolved superconductive QPI techniques thus represent a new approach for study of hidden orbital order.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ultraviolet laser patterning of porous silicon

This work reports on the fabrication of 1D fringed patterns on nanostructured porous silicon (nanoPS) layers (563, 372, and 290 nm thick). The patterns are fabricated by phase-mask laser interference using single pulses of an UV excimer laser (193 nm, 20 ns pulse duration). The method is a single-step and flexible approach to produce a large variety of patterns formed by alternate regions of almost untransformed nanoPS and regions where its surface has melted and transformed into Si nanoparticles (NPs). The role of laser fluence (5–80 mJ cm{sup −2}), and pattern period (6.3–16 μm) on pattern features and surface structuring are discussed. The results show that the diameter of Si NPs increases with fluence up to a saturation value of 75 nm for a fluence ≈40 mJ cm{sup −2}. In addition, the percentage of transformed to non-transformed region normalized to the pattern period follows similar fluence dependence regardless the period and thus becomes an excellent control parameter. This dependence is fitted within a thermal model that allows for predicting the in-depth profile of the pattern. The model assumes that transformation occurs whenever the laser-induced temperature increase reaches the melting temperature of nanoPS that has been found to be 0.7 of that of crystalline silicon for a porosity of around 79%. The role of thermal gradients across the pattern is discussed in the light of the experimental results and the calculated temperature profiles, and shows that the contribution of lateral thermal flow to melting is not significant for pattern periods ≥6.3 μm.

36 MATERIALS SCIENCE↗

Optimal invariant sets for atomistic machine learning

The representation of atomic configurations for machine learning models has led to numerous sets of descriptors. However, many descriptor sets are incomplete and/or functionally dependent. Incomplete sets cannot faithfully represent atomic environments. Yet complete constructions often suffer from a high degree of functional dependence, where some descriptors are functions of others. These redundant descriptors do not improve discrimination between atomic environments. We employ pattern recognition techniques to remove dependent descriptors to produce the smallest possible set that satisfies completeness. We apply this in two ways: First, we refine an existing description, the atomic cluster expansion. Second, we augment an incomplete construction, yielding a new message-passing neural network architecture that can recognize up to 5-body patterns. This architecture shows strong accuracy on state-of-the-art benchmarks while retaining low computational cost. Our results demonstrate the utility of this strategy to optimize descriptor sets across a range of descriptors and application datasets.

97 MATHEMATICS AND COMPUTING↗

Investigation of the effects of passive pre-chamber nozzle pattern and ignition system on engine performance and emissions

The impact of passive pre-chamber (PC) internal volume, nozzle hole pattern (i.e. with and without a central axial nozzle), and PC igniter plug type on performance and emissions was investigated in an optically accessible, single-cylinder, gasoline research engine. The two PC igniter plugs investigated were a conventional inductive coil spark plug and a nanosecond repetitively pulsed (NRP) plasma discharge system previously demonstrated to accelerate early flame propagation. The baseline PC design featured a funnel shaped internal volume with a PC tip that contained six radial nozzles and a larger central axial nozzle. Two additional PC tip geometries were evaluated where either the baseline internal volume was increased or the axial nozzle was removed and the radial nozzle diameters were increased. A sweep of charge equivalence ratios ( ϕ) from nearly stoichiometric to the lean limit was performed for a fixed engine speed (1300 revolutions per minute), and engine load (3.5 bar gross indicated mean effective pressure). Time-resolved PC and main chamber (MC) pressure data as well as MC emissions data were collected to analyze engine performance and emissions characteristics. Combustion in the MC was further investigated using high-speed excited methylidyne radical (CH*) chemiluminescence imaging. Collected results highlighted that while all PC tips and ignition systems exhibited similar performance and emissions down to ϕ = 0.8, relevant differences in thermal efficiency and emissions for leaner charge mixtures were observed, with the results highly dependent on the nozzle pattern and ignition system. Major deviations were correlated to preferential de-pressurization of the PC through the axial nozzle for lean conditions that was not observed for mixture conditions closer to stoichiometric. Results show that a combination of radial and axial nozzle patterns in the PC extended lean-stability limits at the low-load condition evaluated. Further benefits were observed with the use of NRP ignition systems due to faster combustion within the PC volume provided that the volume was sufficiently large.

Di Sabatino, Francesco↗

Fluid structure interaction modelling for the vibration of tube bundles, part I: analysis of the fluid flow in a tube bundle

It is well known that a fluid may strongly influence the dynamic behaviour of a structure. Many different physical phenomena may take place, depending on the conditions: fluid flow, fluid at rest, little or high displacements of the structure. Inertial effects can take place, with lower vibration frequencies, dissipative effects also, with damping, instabilities due to the fluid flow (Fluid Induced Vibration). In this last case the structure is excited by the fluid. Tube bundles structures are very common in the nuclear industry. The reactor cores and the steam generators are both structures immersed in a fluid which may be submitted to a seismic excitation or an impact. In this case the structure moves under an external excitation, and the movement is influence by the fluid. The main point in such system is that the geometry is complex, and could lead to very huge sizes for a numerical analysis. Homogenization models have been developed based on the Euler equations for the fluid. Only inertial effects are taken into account. A next step in the modelling is to build models based on the homogenization of the Navier-Stokes equations. The papers presents results on an important step in the development of such model: the analysis of the fluid flow in a oscillating tube bundle. The analysis are made from the results of simulations based on the Navier-Stokes equations for the fluid. Comparisons are made with the case of the oscillations of a single tube, for which a lot of results are available in the literature. Different fluid flow pattern may be found, depending in the Reynolds number (related to the velocity of the bundle) and the Keulegan Carpenter number (related to the displacement of the bundle). A special attention is paid to the quantification of the inertial and dissipative effects, and to the forces exchanges between the bundle and the fluid. The results of such analysis will be used in the building of models based on the homogenization of the Navier-Stokes equations for the fluid. (authors)

42 ENGINEERING↗

Exploring Functional Materials by Understanding Beam‐Sample Interactions

Abstract Ultra‐low‐dose electron diffraction is performed with a double metal cyanide catalyst (DMC) to understand how electron irradiation stimulates structural alterations in functional materials. The commonly fading diffraction patterns with dose accumulation depend on the irradiated area and the beam current even when below 50 femto Amperes. Heat generation is observed and modeled by statistical, inelastic scattering events to describe how phonon excitations modulate radiation hardness. Specifically, the characteristic 1/e‐decay of Bragg intensities from DMC is delayed from 6 to 30 eÅ −2 at room temperature, which is comparable to the effect of embedding radiation soft matter in ice. DMC's radiation hardness is enhanced by a latency dose that forms during a phase transformation. This unifying model predicts that a critical dose rate exists for any material that varies between 0.1 and 10 4 eÅ −2 s −1 because of a material dependent competition of heat generation and spread. It shows that Brillouin scattering causes time dependent perturbations in electron irradiated solids that trigger time‐temperature‐transformations on a time scale of nanoseconds to microseconds at room temperature, which is not included in traditional models describing the decay of Bragg intensities by radiolysis.

Kisielowski, Christian↗

An Analysis of Characteristics of Magnetostatic Waves Propagating in Nonhomogeneous Fields Across the Ferrospinel Film Thickness

The amplitude-frequency characteristics (AFCs) of magnetostatic waves in the films of magnesium-manganese ferrospinels with nanostructured inhomogeneities are discussed. A common effect, observed in the film AFCs under different process conditions, is the ‘oscillations of propagation’ of magnetostatic waves as a function of the frequency. The oscillation pattern is thought to depend on the inhomogeneous exchange parameters and the surface anisotropy constants. The wave instability is characterized by the resonant interaction of the dipole magnetostatic waves with the surface spin waves. It is shown that the ferrospinel films with periodic nanostructured inhomogeneities of 30–40 nm could be treated as magnon crystals. An inclusion of the inhomogeneity into consideration allows one to provide reasoning for the formation of the rejection bands within the range 9–12 GHz, whose frequencies correspond to Bragg frequencies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Design and optimization of flexible decoupled high-temperature gas-cooled reactor plants with thermal energy storage

Advanced nuclear power plants are well-positioned for future zero-carbon grids, however, the need for flexible power generation will be required over the traditional emphasis on baseload generation for meeting historical demands. To achieve such flexibility, this work examines viable configurations for coupling nuclear energy production with thermal energy storage. Previous designs on nuclear-thermal energy storage configurations for advanced reactor designs, which utilized reactor steam as the heat source for charging the thermal energy storage, are restricted by the heat diversion ratio and efficiency losses, thus their impacts can be limited. In this context, this study proposes configurations for fully decoupling the nuclear reactor from the power cycle and positioning the storage as an intermediate loop, thereby achieving an unconstrained heat diversion ratio and improved efficiency. Compared with a standard high-temperature gas-cooled reactor’s power cycle, steady-state thermodynamic modeling and dispatch optimizations quantify the benefits of a steam reheat cycle within the fully decoupled thermal energy system to separate the plant cycle from the high-pressure primary side. These benefits are further detailed, compatible with required high-temperature and high-pressure conditions, through (1) open-source dynamic transient models that examine the impact of off-design operation on the systems, (2) the investigation of components design and costing and finally (3) sizing and dispatch optimization. The fully-decoupled design achieves a cycle efficiency of 43.1%, an enhancement over the vendor’s standard efficiency of 42.2% (Xe-100 design). Here, the proposed design offers strengthened physical barriers from the nuclear island as well as superior operational flexibility and power boosting. Dispatch optimization and market analysis reveal that thermal energy storage size is highly dependent on the peak patterns of electricity prices and the minimum generation level constraint imposed on the balance of plant. Evaluation of off-design operation demonstrates that the full decoupling design with the suggested fail-safe control mechanisms ensures a minimal impact on reactor parameters, even during rapid power ramping.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Biogeochemical controls on iron speciation and cycling across upland to shoreline gradients in freshwater and estuarine coastal soils (Lake Erie and Chesapeake Bay, United States)

Coastal environments are dynamic interfaces that mediate carbon and nutrient exchanges between terrestrial landscapes and open waters, and understanding the biogeochemical factors controlling these exchanges, particularly iron (Fe) redox transformations, is crucial for predicting coastal ecosystem functions. Here, we investigated the mechanisms controlling Fe speciation changes across upland-to-shoreline gradients in freshwater and estuarine soils using Fe K-edge X-ray absorption spectroscopy, solid and porewater composition analysis, and 16S rRNA sequencing analysis. We show that Fe transformations depend primarily on inundation patterns. In unsaturated uplands, Fe occurs as Fe(III) oxyhydroxides, mainly goethite (9–35 %), Fe(II,III)-phyllosilicates (39–89 %), and Fe(III)-organic species (0–61 %). Soils influenced by estuarine waters exhibit porewater sulfide concentrations reaching up to 221 μM, Fe- and S-cycling bacteria, and up to 81 % pyrite (FeS 2 ), indicating that sulfur-driven redox dynamics control Fe transformations. In lacustrine wetlands, Fe(III) reduction is indicated by porewater Fe(II) concentrations increasing to 1.0–2.1 mM, and ~10–15 % of Fe as Fe(II,III)-(hydr)oxides (green rust), vivianite (Fe 3 (PO 4 ) 2 ·8H 2 O), and/or adsorbed Fe(II) species. EXAFS data also indicate reduction of structural Fe(III) to Fe(II) in phyllosilicates. The presence of Fe- and S-cycling bacteria, as well as sulfide (0–10 μM), suggests that Fe-cycling is microbially driven and potentially coupled with cryptic S-cycling. Fe(II) oxidation was indicated above/near the water table by the presence of Fe(III) oxyhydroxides (ferrihydrite, lepidocrocite). Furthermore, negligible Fe(III) or sulfate reduction was observed at some water-saturated sites located at the upland-wetland transition, likely due to oxic (sub-)surface water inputs. Overall, our results highlight the importance of considering both Fe-speciation and hydro-biogeochemical dynamics when predicting Fe-cycling at coastal interfaces.

54 ENVIRONMENTAL SCIENCES↗

Dynamics and bifurcations of laminar annular swirling and non-swirling jets

This paper presents bifurcation analyses characterising the nonlinear dynamics of fully developed laminar annular jets with respect to the centrebody diameter ${ {d}}$ , Reynolds number ${ {Re}}$ , and swirl ratio ${ {S}}$ . Similar flows appear in numerous applications and feature a vibrant range of topological and dynamical characteristics associated with phenomena including shear layer separation and vortex breakdown. Our results begin by describing the non-monotonic evolution of the axisymmetric jet's steady topology under varying ${ {S}}$ . In accord with earlier reports, the jet progresses through a sequence of wake, breakdown and wall jet regimes in a qualitatively similar manner across a wide span of ${ {d}}$ and ${ {Re}}$ values. In the wake regime, the non-swirling jet bifurcates to a plane-symmetric, but not axisymmetric, steady flow pattern beyond a ${ {d}}$ -dependent critical ${ {Re}}$ value. With further increase in ${ {Re}}$ , the steady non-swirling jet destabilises subsequently via multiple distinct Hopf bifurcations. Introducing ${ {S}}>0$ to the jet also induces unsteadiness by twisting the singly azimuthally periodic ( $|m|=1$ ) asymmetric wake structure and causing it to precess periodically in time about the central axis. Intermediate swirl stabilises this unsteady dynamics and restores the jet's axisymmetry. This stabilising effect is then reversed in the breakdown regime at higher ${ {S}}$ , where a variety of different $|m|=1$ and $|m|=2$ instabilities bifurcate from the steady flow as ${ {S}}$ is increased. Several instances of hysteresis and subcritical behaviour are reported and discussed, including one that manifests precessing vortex core oscillations.

Douglas, Christopher M. (ORCID:0000000259683315)↗

Resonant Soft X-ray Scattering Reveals Hierarchical Structure in a Multicomponent Vapor-Deposited Glass

Multiphase vapor-deposited glasses are an important class of materials for organic electronics, particularly organic photovoltaics and thermoelectrics. These blends are frequently regarded as molecular alloys and there have been few studies of their structure at nanometer scales. Here, in this work, we show that a codeposited system of TPD (N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine) and DO37 (disperse orange 37), two small molecule glass-formers, separates into amorphous, compositionally distinct phases with a domain size and spacing ca. 10s of nanometers that depends on substrate temperature during deposition. Domains rich in one of the two components become larger and more pure at higher deposition temperatures. We use resonant soft X-ray scattering (RSoXS) complemented with atomic force microscopy (AFM) and photoinduced force microscopy to measure the phase separation, topography, and purity of the deposited films. A forward-simulation approach to RSoXS analysis, the National Institute of Standards and Technology RSoXS Simulation Suite (NIST RSoXS simulation suite), is used with models developed from AFM images to evaluate the energy dependence of scattering across multiple length scales and interpret the RSoXS with respect to structure within the films. We find that the RSoXS is sensitive to a length scale of phase separation buried within the film that is consistent with the surface composition profile, and correlates to the topography to an extent that depends on substrate temperature. We demonstrate that vacuum scattering, which is often ignored in RSoXS analysis, contributes significantly to the features and energy dependence of the RSoXS pattern, and then illustrate how to properly account for vacuum scattering to analyze films with significant roughness. We then use this analysis framework to understand structure development mechanisms that occur during vapor deposition of a TPD-DO37 codeposited glass with results that outline paths to tune morphology in multicomponent materials.

36 MATERIALS SCIENCE↗

Spin Reorientation in Antiferromagnetic Layered FePt 5 P

FePt 5 P, a substitutional variant of the anti-CeCoIn 5 structure type in the space group P4/mmm, was synthesized by a high-temperature solid-state method and structurally characterized by X-ray diffraction. FePt 5 P contains layers of FePt 12 clusters formed by magnetically active Fe and heavy Pt with strong spin-orbit coupling (SOC); the layers are separated by P atoms. The various Fe–Pt distances in FePt 12 clusters generate complex magnetic orders in FePt 5 P. According to temperature-dependent magnetic and specific heat measurements, FePt 5 P shows a stripe-type antiferromagnetic order at T N ≈ 90 K, which is also confirmed by resistivity measurements. Furthermore, a spin reorientation occurs at ~74 and ~68 K in and out of the ab plane based on the specific heat measurements. The temperature-dependent neutron powder diffraction patterns demonstrate the antiferromagnetic order in FePt 5 P, and the spins orientate up to 58.4° with respect to the c axis at 10 K. First-principles calculations of FePt 5 P show the band splitting at the Fermi level by strong SOC and the s–d hybridization between P and Fe/Pt electrons enhances the structural stability and affects the magnetic ordering.

36 MATERIALS SCIENCE↗

The Dependence of Climate Sensitivity on the Meridional Distribution of Radiative Forcing

Abstract This study investigates how climate sensitivity depends upon the spatial pattern of radiative forcing. Sensitivity experiments using a coupled ocean‐atmosphere model were conducted by adding anomalous incoming solar radiation over the entire globe, Northern Hemisphere mid‐latitudes, Southern Ocean, and tropics. The varied forcing patterns led to highly divergent climate sensitivities. Specifically, the climate is nearly twice as sensitive to Southern Ocean forcing as tropical forcing. Strong coupling between the surface and free troposphere in the tropics increases the inversion strength, leading to smaller cloud feedback in the tropical forcing experiments. In contrast, the extratropics exhibit weaker coupling, a decrease or near‐zero change in the inversion strength, and strong positive cloud feedback. These results contrast with the conventional SST‐pattern effect in which tropical surface temperature changes regulate climate sensitivity. They also have important implications for other potentially asymmetric forcings, such as those from geoengineering, volcanic eruptions, and paleoclimatic changes.

54 ENVIRONMENTAL SCIENCES↗

Impact of decadal cloud variations on the Earth’s energy budget

Feedbacks of clouds on climate change strongly influence the magnitude of global warming. Cloud feedbacks, in turn, depend on the spatial patterns of surface warming, which vary on decadal timescales. Therefore, the magnitude of the decadal cloud feedback could deviate from the long-term cloud feedback. We present climate model simulations to show that the global mean cloud feedback in response to decadal temperature fluctuations varies dramatically due to time variations in the spatial pattern of sea surface temperature. Here, we find that cloud anomalies associated with these patterns significantly modify the Earth’s energy budget. Specifically, the decadal cloud feedback between the 1980s and 2000s is substantially more negative than the long-term cloud feedback. This is a result of cooling in tropical regions where air descends, relative to warming in tropical ascent regions, which strengthens low-level atmospheric stability. Under these conditions, low-level cloud cover and its reflection of solar radiation increase, despite an increase in global mean surface temperature. Our results suggest that sea surface temperature pattern-induced low cloud anomalies could have contributed to the period of reduced warming between 1998 and 2013, and o er a physical explanation of why climate sensitivities estimated from recently observed trends are probably biased low.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Direct observation of the dead-cone effect in quantum chromodynamics

In particle collider experiments, elementary particle interactions with large momentum transfer produce quarks and gluons (known as partons) whose evolution is governed by the strong force, as described by the theory of quantum chromodynamics (QCD). These partons subsequently emit further partons in a process that can be described as a parton shower, which culminates in the formation of detectable hadrons. Studying the pattern of the parton shower is one of the key experimental tools for testing QCD. This pattern is expected to depend on the mass of the initiating parton, through a phenomenon known as the dead-cone effect, which predicts a suppression of the gluon spectrum emitted by a heavy quark of mass m Q and energy E, within a cone of angular size m Q /E around the emitter. Previously, a direct observation of the dead-cone effect in QCD had not been possible, owing to the challenge of reconstructing the cascading quarks and gluons from the experimentally accessible hadrons. We report the direct observation of the QCD dead cone by using new iterative declustering techniques to reconstruct the parton shower of charm quarks. This result confirms a fundamental feature of QCD. Furthermore, the measurement of a dead-cone angle constitutes a direct experimental observation of the non-zero mass of the charm quark, which is a fundamental constant in the standard model of particle physics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Real-time near-field imaging of photoinduced matter motion in thin solid films containing azobenzene derivatives

We present a study of the formation of surface relief gratings in thin solid films containing azobenzene derivatives upon illumination with an interference pattern. This study is based on near-field microscopy techniques that provide real-time imaging of both the photomechanical response of the material and light excitation profile. We demonstrate that the material deformation follows two distinct regimes characterized by different kinetics, a different phase relative to the light intensity pattern, and a specific dependence on light polarization.

36 MATERIALS SCIENCE↗