Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mismatch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

DIS at low and high transverse momentum: matches and mismatches

This talk [1] reports on a recent work [2] where we studied the connection between the description of semi-inclusive DIS at high transverse momentum (based on collinear factorization) and low transverse momentum (based on TMD factorization). We used power counting to determine the leading behavior of the structure functions at intermediate transverse momentum in the two descriptions. When the power behaviors are different, two distinct mechanisms are present and there can be no matching between them. When the power behavior is the same, the two descriptions must match. An explicit calculation however shows that for some observables this is not the case, suggesting that the TMD-factorization description beyond leading twist is incomplete.

Bacchetta, Alessandro↗

The effect of mismatched components on microwave noise-temperature calibrations

Analysis of errors on microwave noise-temperature measurements is important due to development of very low-noise antenna receiving systems and in the absolute accuracies to which the noise temperatures of these systems can be calibrated. Scattering parameters describe properties of the microwave network connected between noise source and receiver.

Otoshi, T. Y.↗

Control of linear uncertain systems utilizing mismatched state observers

The control of linear continuous dynamical systems is investigated as a problem of limited state feedback control. The equations which describe the structure of an observer are developed constrained to time-invarient systems. The optimal control problem is formulated, accounting for the uncertainty in the design parameters. Expressions for bounds on closed loop stability are also developed. The results indicate that very little uncertainty may be tolerated before divergence occurs in the recursive computation algorithms, and the derived stability bound yields extremely conservative estimates of regions of allowable parameter variations.

Goldstein, B.↗

Effects of mismatch on group delay of microwave transmission

Calculation method can be applied to transmission lines operating in TEM mode or to single-mode propagation in waveguides. Derived data are useful for estimating limits on variation of group delay with frequency or in determining how much discontinuity reduction is necessary to achieve given accuracy in predicting group delay.

Beatty, R. W.↗

The effect of a visual/motion display mismatch in a single axis compensatory tracking task

The frequency response of visual systems is typically unity from 0 to 20 rad/sec, while that of motion systems typically falls off in the vicinity of 6 rad/sec. The question arises as to what effect, if any, such a difference in servomechanism performance has on the simulation. Is pilot performance reduced by the conflict between displays? Would a more realistic simulation occur if the visual servomechanisms were degraded to match the motion servomechanisms? Does the pilot need and use the higher frequency information present in the visual display? The purpose of the experiment is to take a step forward toward answering these questions. Work already in the literature which bears on these questions is outlined. A description is then given of an experiment used to check for the effects of a difference in the performance of the visual and motion servomechanisms (the experiment uses a single-axis, compensatory, roll-tracking task). The results of the experiment are then presented and analyzed.

Shirachi, D. K.↗

The correction for spectral mismatch effects on the calibration of a solar cell when using a solar simulator

A general expression was derived to enable calculation of the calibration error. The information required includes the relative spectral response of the reference cell, the relative spectral response of the cell under test, and the relative spectral irradiance of the simulator (over the spectral range defined by cell response). The spectral irradiance of the solar AMX is assumed to be known.

Seaman, C. H.↗

Flexible Seal Accommodates Part Mismatch

Chain of plates embedded in flexible seal enables it to withstand side loading of 2,300 psi (116MPa) while sealing gap of up to 0.5 inch (13 mm) between cylindrical chamber wall and test fixture. Pressure-actuated seal along inner edge forces seal into contact even though cylinder wall becomes eccentric as cylinder pressure increases. Seal has many industrial applications, particularly where heat or pressure causes distortion of chamber being sealed.

Bobb, I.↗

Visual/motion cue mismatch in a coordinated roll maneuver

The effects of bandwidth differences between visual and motion cueing systems on pilot performance for a coordinated roll task were investigated. Visual and motion cue configurations which were acceptable and the effects of reduced motion cue scaling on pilot performance were studied to determine the scale reduction threshold for which pilot performance was significantly different from full scale pilot performance. It is concluded that: (1) the presence or absence of high frequency error information in the visual and/or motion display systems significantly affects pilot performance; and (2) the attenuation of motion scaling while maintaining other display dynamic characteristics constant, affects pilot performance.

Shirachi, D. K.↗

Technical support package: Flexible seal accommodates part mismatch. NASA Tech Briefs, Fall 1982, volume 7, no. 1

A radial seal for the inside diameter of a part that develops an out-of-round condition and grows under pressure was developed. The primary seal consists of overlapping segments fabricated from metal or composite material that has been molded into a rubber jacket. The purpose of the segments is to provide the strength to withstand side loads (seal tested at 2,300 psi), and the rubber encapsulation provides the sealing surface and needed flexibility to conform to the variable eccentric shape.

Source record↗

Fastening Parts Having Mismatched Thermal Coefficients

Fastener eliminates thermal stresses and maintains snug fit. Conicalhead bolt and metal washer main components of fastener that keeps constant tension on carbon/carbon parts regardless of thermal stress. Fastener used in cases where fastened parts have unmatched thermalexpansion coefficients. Does not become looser or tighter as conventional bolts and nuts or rivets do at elevated temperatures.

Jackson, L. R.↗