Results for “microstructure engineering” — Page 16

DOE OSTI2022

Scaling CFB risers: Maintaining microstructure dynamics

Over the years there have been numerous approaches to develop a scaleup methodology for circulating fluidized beds. Many of these past approaches have relied on macroscopic definitions of similitude to define dimensionless groups such as Reynolds number, Froude number, density ratios, and dimensional ratios involving different length scales. These approaches have demonstrated various levels of success, but often fail when used outside the bounds of experimental datasets. The issue with these methods is that they rely on macroscopic similitude with the hopes that those conditions would provide microscopic similitude as it does in single phase systems where the Buckingham Pi techniques have given reasonable success. Two of the main reasons for failure are 1) changing fluidization regimes and 2) changing material properties that result in the material falling into a different Geldart group. Both are certain to change the microstructure (local instantaneous volume solids fraction) and changes to the microstructure affect the interphase transport properties of the reactor system, namely the mass transfer and heat transfer. Here, this work presents a new approach towards scaling based upon maintaining similitude at the microscale. It reviews a novel dimensionless flow regime map developed from analysis of the deterministic chaos parameters and higher order moments to ensure microstructure similitude. The work then examines four cases from the literature to assess the scaling approach used: (1) same particle-different scale risers for Geldart Group B particles, (2) Glicksman scaling of atmospheric circulating fluidized bed combustor, (3) same particle-different scale risers for Geldart Group A particles and (4) Glicksman scaling for pressurized gasification. General findings are that none of the scaling approaches produced directly applicable microstructure similar behavior based upon the chaotic and higher moment analysis. The positive take away is that the approach can define scale conditions that will provide similar microstructure that can be us to predict transport behavior.

42 ENGINEERING↗

DOE OSTI2020

Particle interspacing effects on the mechanical behavior of a Fe–TiB 2 metal matrix composite using FFT-based mesoscopic field dislocation mechanics

This paper presents an application to metal matrix composites (MMCs) of an enhanced elasto-viscoplastic Fast Fourier Transform (EVP-FFT) formulation coupled with a phenomenological continuum Mesoscale Field Dislocation Mechanics (MFDM) theory. Contrary to conventional crystal plasticity, which only accounts for plastic flow and hardening induced by statistically stored dislocations (SSDs), MFDM-EVP-FFT also describes the evolution of polarized geometrically necessary dislocation (GND) density and its effect on both plastic flow and hardening. Numerical results for a Fe–TiB 2 MMC made of a ferrite matrix (α-Fe) and elastic ceramic particles (TiB 2 ) are presented. Full-field simulations are performed using synthetic periodic unit cells representative of the MMC, with single-crystalline and polycrystalline matrix, for different particle interspacing distances. A strong dependence of the predicted equivalent stress, cumulated plastic strain and GND density fields with particle interspacing distance is observed, in contrast with conventional crystal plasticity. Correlations between these mechanical fields and microstructural features, and their influence on local and global mechanical behavior are examined for the different MMC microstructures.

42 ENGINEERING↗

DOE OSTI2021

Examination of Intergranular Crack on SC0234

The microstructure of the SC0234 weld was evaluated per DA-SPEC-01067, ''General Purpose Heat Source (GPHS) Plutonium-238 Dioxide Fueled Clad Product Specification'' and it was determined that the weld microstructure conformed to the quality requirements. During the examination of weld cross section, the metallographic analysis revealed the presence of a surface crack. Prior visual examination per RPS-TA55-303 had not revealed the crack, nor did the surface photography performed per RPS-TA55-302. The presence of the crack does not violate any of the product specifications called out on DA-SPEC-01067. Although there is a well-documented history of weld hot crack susceptibility in the early development of the DOP-26 iridium alloy, a surface crack such as this had not been documented during welding at Los Alamos. In the interest of better understanding the cause; the product engineer/program recommended further examination of the crack. This report discusses the examination of the crack found in the weld cross section of simulant clad SC0234. Metallography, Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy techniques (EDS) where used in the analysis of the crack and the surrounding weld microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2023

The Physical and Engineering Limits of Coupled In situ TEM Experiments

Almost all future energy systems (advanced nuclear reactors, fusion energy system, concentrating solar-thermal power (CSP), and wind technologies) are limited by degradation of key material systems exposed to multiple environmental stressors. The degradation during exposure to high temperatures, radiation, mechanical loading, and chemical attack is often dictated by mechanisms active at the microstructural level. The nature of these mechanisms and the associated variations between sequential and concurrent interplay can be explored if the transmission electron microscope (TEM) is utilized as a toolbox for exploration [1]. One such tool developed at Sandia National Laboratories to couple several of these environments is the In situ Ion Irradiation TEM (I3TEM) [2]. Several studies over the last decade utilizing this tool have shown that the scientific intuition developed over decades of sequential experiments is not always a good indicator of concurrent mechanisms or failure routes. This presentation will highlight the recent and planned additions into the I3TEM facility of a Waviks gas injection system and Raman system, respectively, as can be seen in Fig. 1, permitting environmental degradation from gas species leaked into the pole piece region during quantitative mechanical loading (indentation, monotonic loading, high temperature creep, irradiation induced creep, and high-cycle fatigue); multi-beam ion irradiation (energies ranging from 1 keV to 48 MeV and species from H to Au); laser exposure (20 W and 1064 nm), or various combinations thereof that are already possible [3]. This addition permits the facility to explore both sequential or concurrently the four axes of stressors: thermal, mechanical, radiation, and chemical. This information can be directly coupled to modeling, expediting the refinement and validation of both atomistic and mesoscale models.

degradation↗

DOE OSTI2021

Characteristics of Premature Creep Failure in Over-tempered Base Metal of Grade 91 Steel Weldment

Characteristics of premature creep failure in the over-tempered base metal (OT-BM) of a Grade 91 steel weldment are investigated with specially designed creep experiments and advanced microstructure characterization. In situ digital image correlation (DIC) strain measurements reveal that local creep strain as high as 100% accumulated in the OT-BM, compared with only 10% nominal strain over the gauge length. The creep strain rate in the OT-BM is identical to that in the intercritical heat-affected zone and fine-grained heat-affected zone at the secondary creep stage and early tertiary stage, but faster at the late tertiary stage. Microstructural analysis shows that highly recovered microstructure in the OT-BM leads to the lowest hardness, the largest grain size, the lowest fraction of coincidence site lattice boundaries, and the lowest localized strain energy. Dislocation creep and transgranular creep fracture are the dominant deformation and fracture mechanisms in the OT-BM under the current creep testing condition of a low temperature (550 °C) and a high stress (215 MPa).

42 ENGINEERING↗

DOE OSTI2022

Sample Preparation and Experimental Design for In Situ Multi-Beam Transmission Electron Microscopy Irradiation Experiments

We discuss the need to understand materials exposed to overlapping extreme environments such as high temperature, radiation, or mechanical stress. When these stressors are combined there may be synergistic effects that enable unique microstructural evolution mechanisms to activate. Understanding of these mechanisms is necessary for the input and refinement of predictive models and critical for engineering of next generation materials. The basic physics and underlying mechanisms require advanced tools to be investigated. The in situ ion irradiation transmission electron microscope (I 3 TEM) is designed to explore these principles. To quantitatively probe the complex dynamic interactions in materials, careful preparation of samples and consideration of experimental design is required. Particular handling or preparation of samples can easily introduce damage or features that obfuscate the measurements. There is no one correct way to prepare a sample; however, many mistakes can be made. The most common errors and things to consider are highlighted within. The I 3 TEM has many adjustable variables and a large potential experimental space, therefore it is best to design experiments with a specific scientific question or questions in mind. Experiments have been performed on large number of sample geometries, material classes, and with many irradiation conditions. The following are a subset of examples that demonstrate unique in situ capabilities utilizing the I 3 TEM. Au nanoparticles prepared by drop casting have been used to investigate the effects of single ion strikes. Au thin films have been used in studies on the effects of multibeam irradiation on microstructure evolution. Zr films have been exposed to irradiation and mechanical tension to examine creep. Ag nanopillars were subjected to simultaneous high temperature, mechanical compression, and ion irradiation to study irradiation induced creep as well. These results impact fields including: structural materials, nuclear energy, energy storage, catalysis, and microelectronics in space environments.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Adoption of image-driven machine learning for microstructure characterization and materials design: A Perspective

Microstructure characterization enables the development of structure-processing-property relationships critical to several research areas within the broad field of materials science, from alloy design to the assessment of corrosion resistance, and failure analysis. Conventional approaches to material characterization have relied on either qualitative inference by the human ex-pert or software applications that can extract high-level features from images, such as boundary segmentation, average grain diameter, etc. Such approaches rely heavily on subject matter expert user intervention and knowledge of what phases or more generally, what microstructural features, are of interest. The recent surge in the adoption of machine learning techniques to address problems in materials engineering has brought with it an increased interest and application of Image Driven Machine Learning (IDML) approaches. In this work, we review the applications of IDML to the field of materials characterization. A canonical hierarchy of stages is defined, which when put sequentially together completes an IDML study: problem definition, dataset building, model selection and training, model evaluation, and integration with existing instrumentation or simulation workflow. The studies reviewed in this work are analyzed from the perspective of each of these stages. Such a review permits agranular assessment of the field, for example the impact of IDML on materials characterization at the nanoscale, the size of a typical dataset required to train a semantic segmentation model on electron microscopy images, ubiquitousness of transfer learning in the domain, etc. Finally, we discuss the importance of interpretability and explainability in the field of IDML for materials characterization, and provide an overview of two emerging techniques in the field: semantic segmentation and generative adversarial networks.

Baskaran, Arun↗

DOE OSTI2026

Aperture and roughness govern iron oxide passivation in olivine fractures during carbon mineralization

Efficient carbon dioxide mineralization in silicate-rich formations depends on reaction rates within fracture networks, yet the role of fracture microstructure remains poorly constrained. We investigated how fracture aperture and surface roughness influence mineralization by reacting synthetic forsteritic olivine fractures with controlled apertures (0.5–1.6 millimeters) and roughness (6–16 micrometers) with supercritical carbon dioxide at 13.7 megapascals and 185 degrees Celsius. Optical microscopy and Raman spectroscopy showed that rougher fracture surfaces promoted iron oxide precipitation, which passivated olivine surfaces, limiting magnesium availability for carbonate formation while removing iron as a reactant. These effects were more pronounced in smaller-aperture fractures. A geochemical model incorporating surface topography and passivation reproduced the observed trends, confirming that increased roughness can reduce reactivity despite greater surface area. Our results demonstrate that fracture microstructure strongly influences iron oxide passivation and carbon dioxide mineralization, with important implications for predicting long-term performance of engineered carbon dioxide storage systems.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Neutronic engine

An internal combustion engine for neutron diffraction analysis is provided. The engine includes an elongated piston chamber formed from an aluminum alloy to ensure maximum neutron visibility into the combustion chamber. An elongated piston assembly reciprocates within the elongated piston chamber, the piston assembly including an upper piston joined to a lower piston. The upper piston and the lower piston are hollow, thereby reducing the reciprocating mass and increasing neutron access to the combustion chamber. The upper piston is lubricated with a neutron-transparent fluorocarbon lubricant such as perfluoropolyether (PFPE), while the lower piston and the crankcase are lubricated with hydrocarbon lubricant. The engine enables 3D and time-resolved measurements of strain, stress, and temperature, as well as phase transformation, texture, and microstructure.

Wissink, Martin L.↗

DOE OSTI2021

Simulated effects of sample size and grain neighborhood on the modeling of extreme value fatigue response

Assessing the size of representative volume elements (RVEs) for fatigue-related applications is challenging. A RVE relevant to random microstructure requires a volume of material that is sufficiently large to capture the grain/phase heterogeneity that captures all statistical moments of the distribution of the driving force for fatigue crack formation at “hot spot” grains. Consequently, the large size of a microstructure RVE required to study fatigue phenomena is largely computationally intractable and difficult to explore. A more realistic objective in this work is to systematically study, as a function of the size of a statistical sample of microstructure, trends towards convergence of the simulated distribution of driving force for fatigue crack formation. Our present work accordingly leverages the recently developed open-source PRISMS-Fatigue framework to examine the trends in convergence of extreme value distributions (EVD) of Fatigue Indicator Parameters (FIPs) in progressively larger polycrystalline microstructure realizations of FCC Al alloy 7075-T6 using crystal plasticity finite element method simulations. The results are compared to the traditional method in which ensembles of statistical volume elements (SVEs) are simulated to build up statistics intended to approximate those associated with a larger volume of material. The convergence of EVDs with increase of size of a SVE of microstructure is closely related to the extent of grain nearest neighbor (NN) interactions. Accordingly, the sensitivity of the local micromechanical response at hot spot grains is quantitatively investigated by systematically varying the orientations of NN grains. Results indicate that SVEs with cubic crystallographic texture tend towards convergence of the EVD of FIPs with tens of thousands of grains while the random and rolled textures require larger volumes. Simple relationships based on microstructure parameters (e.g., Schmid Factor, grain size, NN misorientation) do not completely correlate to fatigue hot spot grains. Finally, the sensitivity of the extreme value fatigue response at hot spot grains extends to the 3rd NN when a single neighborhood grain orientation is altered.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Development of grain-scale slip activity and lattice rotation fields in Inconel 718

Using a combination of in-situ high-resolution digital image correlation (HR-DIC), Heaviside-DIC method (H-DIC), and crystal plasticity finite element (CPFE), we investigate the evolution of intragranular lattice rotations and slip activity during monotonic and cyclic loading in a high performance, polycrystalline face centered cubic material. The CPFE employs a quasi-3D model microstructure, which is a highly resolved mirror representation of the experimental in-situ test sample. In agreement, the measurements and calculations reveal that most grains, regardless of their size and lattice orientation, develop intragranular lattice rotation gradients that span the grain. For a small cluster of grains on the deformed material, we perform HR-DIC analysis of slip lines to demonstrate agreement in the active slip systems and changes in this local slip activity across the individual grains. The combined analysis reveals that deforming grains are divided into sub-granular regions of uniform lattice rotation and these regions are most often associated with only one or two active slip systems. The gradient lines that divide them correspond to changes in the predominant slip system. The model is used to examine the evolution of intragranular lattice rotation in a single fully reversed tension-compression cycle. The calculations indicate that intragranular gradients intensify during the reverse loading path as nearest neighboring regions appear to shed lattice rotation, increasing the lattice rotation in some regions, while shutting down rotation in neighboring regions. So these findings provide insight into the irreversible changes that develop within deforming grains at the scale of the grain, particularly the heterogeneous development of intragranular lattice rotation in early stages of deformation, which could serve as precursors to localization.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Study of Helium Irradiation Effect on Al6061 Alloy Fabricated by Additive Friction Stir Deposition

Additive friction stir deposition (AFS-D) is considered a productive method of additive manufacturing (AM) due to its ability to produce dense mechanical parts at a faster deposition rate compared to other AM methods. Al6061 alloy finds extensive application in aerospace and nuclear engineering; nevertheless, exposure to radiation or high-energy particles over time tends to deteriorate their mechanical performance. However, the effect of radiation on the components manufactured using the AFS-D method is still unexamined. In this work, samples from the as-fabricated Al6061 alloy, by AFS-D, and the Al6061 feedstock rod were irradiated with He+ ions to 10 dpa at ambient temperature. The microstructural and mechanical changes induced by irradiation of He+ were examined using a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and nanoindentation. This study demonstrates that, at 10 dpa of irradiation damage, the feedstock Al6061 produced a bigger size of He bubbles than the AFS-D Al6061. Nanoindentation analysis revealed that both the feedstock Al6061 and AFS-D Al6061 samples have experienced radiation-induced hardening. These studies provide a valuable understanding of the microstructural and mechanical performance of AFS-D materials in radiation environments, offering essential data for the selection of materials and processing methods for potential application in aerospace and nuclear engineering.

36 MATERIALS SCIENCE↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

Feature Based Qualification of 17-4PH Stainless Steel to Evaluate Location-Specific Variability in Wire Arc Additive Manufacturing

Qualifying large-scale metal additive manufacturing (M-AM) technologies such as wire arc additive manufacturing (WAAM) can be challenging. This is especially significant in precipitation hardened martensitic stainless steels like SS 17-4PH, where thermal histories induce location-specific microstructural variability and property anisotropy. The Department of Defense (DOD) and the United States Army Combat Capabilities Development Command Ground Vehicle Systems Center (GVSC) Ground Vehicle Materials Engineering (GVME) aim to build robust and qualified large-scale M-AM workflows that could reduce the time and cost through quick and informed evaluation, testing, and development of feedstock, processes, and parts. The report presents the findings from the collaborative efforts between Oak Ridge National Laboratory (ORNL) and the U.S. Army GVSC GVME. The aim of this project was to develop a geometric feature-based qualification framework for WAAM of SS 17-4PH components. This report outlines selection methodology of representative build geometries, optimization of WAAM process parameters, in-situ monitoring, microstructure-property evaluation, thermal simulations, as well as data visualization techniques incorporated in this project. The results from this project demonstrate a clear understanding of thermal history dependent phase evolution and consequent location-specific property variations in WAAM of SS 17-4PH. These results in conjunction with the data-driven methodologies used in this project are expected to reduce qualification timelines, improve predictability, and accelerate the development of reliable feature-based qualification strategies for part production via large-scale M-AM technologies.

36 MATERIALS SCIENCE↗