Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

A Universal Tare Load Prediction Algorithm for Strain-Gage Balance Calibration Data Analysis

An algorithm is discussed that may be used to estimate tare loads of wind tunnel strain-gage balance calibration data. The algorithm was originally developed by R. Galway of IAR/NRC Canada and has been described in the literature for the iterative analysis technique. Basic ideas of Galway's algorithm, however, are universally applicable and work for both the iterative and the non-iterative analysis technique. A recent modification of Galway's algorithm is presented that improves the convergence behavior of the tare load prediction process if it is used in combination with the non-iterative analysis technique. The modified algorithm allows an analyst to use an alternate method for the calculation of intermediate non-linear tare load estimates whenever Galway's original approach does not lead to a convergence of the tare load iterations. It is also shown in detail how Galway's algorithm may be applied to the non-iterative analysis technique. Hand load data from the calibration of a six-component force balance is used to illustrate the application of the original and modified tare load prediction method. During the analysis of the data both the iterative and the non-iterative analysis technique were applied. Overall, predicted tare loads for combinations of the two tare load prediction methods and the two balance data analysis techniques showed excellent agreement as long as the tare load iterations converged. The modified algorithm, however, appears to have an advantage over the original algorithm when absolute voltage measurements of gage outputs are processed using the non-iterative analysis technique. In these situations only the modified algorithm converged because it uses an exact solution of the intermediate non-linear tare load estimate for the tare load iteration.

balance calibration analysis↗
NASA NTRS1974

Flight tests of Viking parachute system in three Mach number regimes. 2: Parachute test results

Tests of the Viking 16.15-meter nominal-diameter disk-gap-band parachute were conducted at Mach number and dynamic pressure conditions which bracketed the range postulated for the Viking '75 mission to Mars. Parachutes were deployed at supersonic, transonic, and subsonic speeds behind a simulated Viking entry capsule. All parachutes successfully deployed, inflated, and exhibited sufficient drag and stability for mission requirements. Basic parachute data including loads, drag coefficients, pull-off angles, and canopy area ratios are presented. Trajectory reconstruction and onboard camera data methods were combined to yield continuous histories of both parachute and test-vehicle angular motions which are presented for the period from parachute deployment through steady inflation.

Bendura, R. J.↗
NASA NTRS1978

On methods for application of harmonic control

The paper presents data which confirm the effectiveness of higher harmonic blade pitch control in substantially reducing helicopter rotor vibratory hub loads. The data are the result of recent tests on a 2.7-m model conducted in the Langley Research Center's transonic dynamics wind tunnel. Several predictive analyses developed in support of the NASA program are shown capable of accurately predicting both amplitude and phase of the higher harmonic control input required to nullify a single 4/rev force or moment input. The use of multiple blade feathering inputs in the design of a flightworthy higher harmonic control system is discussed.

Wood, E. R.↗
NASA NTRS2004

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. An ECT specimen is a rectangular laminate, containing an edge delamination at the laminate mid-plane. Torsion load is applied to the specimens, resulting in relative transverse shear sliding of the delaminated faces. The test data reduction schemes are intended to yield initiation values of critical mode III strain energy release rate, G(sub IIIc), that are constant with delamination length. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design as a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and specimens made from S2/8552 tape laminates. Several specimens, each with different delamination lengths are tested. Detailed, three-dimensional finite element analyses of the specimens were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode III-dominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of G(sub IIIc) exhibited significant dependence on delamination length. Furthermore, there was a large amount of scatter in the data. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Ratcliffe, James G.↗
NASA NTRS1959

Investigation of the Maximum Spin-Up Coefficients of Friction Obtained During Tests of a Landing Gear Having a Static-Load Rating of 20,000 Pounds

An experimental investigation was made at the Langley landing loads track to obtain data on the maximum spin-up coefficients of friction developed by a landing gear having a static-load rating of 20,000 pounds. The forward speeds ranged from 0 to approximately 180 feet per second and the sinking speeds, from 2.7 feet per second to 9.4 feet per second. The results indicated the variation of the maximum spin-up coefficient of friction with forward speed and vertical load. Data obtained during this investigation are also compared with some results previously obtained for nonrolling tires to show the effect of forward speed.

Batterson, Sidney A.↗
NASA NTRS1995

Microcracking in composite laminates under thermal and mechanical loading

Composites used in space structures are exposed to both extremes in temperature and applied mechanical loads. Cracks in the matrix form, changing the laminate thermoelastic properties. The goal of the present investigation is to develop a predictive methodology to quantify microcracking in general composite laminates under both thermal and mechanical loading. This objective is successfully met through a combination of analytical modeling and experimental investigation. In the analysis, the stress and displacement distributions in the vicinity of a crack are determined using a shear lag model. These are incorporated into an energy based cracking criterion to determine the favorability of crack formation. A progressive damage algorithm allows the inclusion of material softening effects and temperature-dependent material properties. The analysis is implemented by a computer code which gives predicted crack density and degraded laminate properties as functions of any thermomechanical load history. Extensive experimentation provides verification of the analysis. AS4/3501-6 graphite/epoxy laminates are manufactured with three different layups to investigate ply thickness and orientation effects. Thermal specimens are cooled to progressively lower temperatures down to -184 C. After conditioning the specimens to each temperature, cracks are counted on their edges using optical microscopy and in their interiors by sanding to incremental depths. Tensile coupons are loaded monotonically to progressively higher loads until failure. Cracks are counted on the coupon edges after each loading. A data fit to all available results provides input parameters for the analysis and shows them to be material properties, independent of geometry and loading. Correlation between experiment and analysis is generally very good under both thermal and mechanical loading, showing the methodology to be a powerful, unified tool. Delayed crack initiation observed in a few cases is attributed to a lack of preexisting flaws assumed by the analysis. Some interactions between adjacent ply groups are attributed to local stress concentrations. These two effects are not captured by the analysis due to its global nature. The analysis is conservative in these cases and agrees well with data after the observed onset of cracking.

Maddocks, Jason R.↗
NASA NTRS2012

Analysis of Ares Crew Launch Vehicle Transonic Alternating Flow Phenomenon

A transonic wind tunnel test of the Ares I-X Rigid Buffet Model (RBM) identified a Mach number regime where unusually large buffet loads are present. A subsequent investigation identified the cause of these loads to be an alternating flow phenomenon at the Crew Module-Service Module junction. The conical design of the Ares I-X Crew Module and the cylindrical design of the Service Module exposes the vehicle to unsteady pressure loads due to the sudden transition between a subsonic separated and a supersonic attached flow about the cone-cylinder junction as the local flow randomly fluctuates back and forth between the two flow states. These fluctuations produce a square-wave like pattern in the pressure time histories resulting in large amplitude, impulsive buffet loads. Subsequent testing of the Ares I RBM found much lower buffet loads since the evolved Ares I design includes an ogive fairing that covers the Crew Module-Service Module junction, thereby making the vehicle less susceptible to the onset of alternating flow. An analysis of the alternating flow separation and attachment phenomenon indicates that the phenomenon is most severe at low angles of attack and exacerbated by the presence of vehicle protuberances. A launch vehicle may experience either a single or, at most, a few impulsive loads since it is constantly accelerating during ascent rather than dwelling at constant flow conditions in a wind tunnel. A comparison of a windtunnel- test-data-derived impulsive load to flight-test-data-derived load indicates a significant over-prediction in the magnitude and duration of the buffet load. I. Introduction One

Sekula, Martin K.↗
NASA NTRS2010

Analysis of a Transonic Alternating Flow Phenomenon Observed During Ares Crew Launch Vehicle Wind Tunnel Tests

A transonic wind tunnel test of the Ares I-X Rigid Buffet Model (RBM) identified a Mach number regime where unusually large buffet loads are present. A subsequent investigation identified the cause of these loads to be an alternating flow phenomenon at the Crew Module-Service Module junction. The conical design of the Ares I-X Crew Module and the cylindrical design of the Service Module exposes the vehicle to unsteady pressure loads due to the sudden transition from separated to attached flow about the cone-cylinder junction with increasing Mach number. For locally transonic conditions at this junction, the flow randomly fluctuates back and forth between a subsonic separated flow and a supersonic attached flow. These fluctuations produce a square-wave like pattern in the pressure time histories which, upon integration result in large amplitude, impulsive buffet loads. Subsequent testing of the Ares I RBM found much lower buffet loads since the evolved Ares I design includes an ogive fairing that covers the Crew Module-Service Module junction, thereby making the vehicle less susceptible to the onset of alternating flow. An analysis of the alternating flow separation and attachment phenomenon indicates that the phenomenon is most severe at low angles of attack and exacerbated by the presence of vehicle protuberances. A launch vehicle may experience either a single or, at most, a few impulsive loads since it is constantly accelerating during ascent rather than dwelling at constant flow conditions in a wind tunnel. A comparison of a wind-tunnel-test-data-derived impulsive load to flight-test-data-derived load indicates a significant over-prediction in the magnitude and duration of the buffet load

Sekula, Martin K.↗
NASA NTRS2004

Erlang B/C Link Availability/Blockage for Data and Voice over VDL Mode 3

This study looks into the blockage and availability of Digital VHF Mode 3 link. Using future predicted voice and CPDLC data traffic loads, the Erlang B and Erlang C formulas were utilized to measure the availability/blockage of the two applications over VDL mode 3. The results here, along with previous cell capacity calculations on the number of frequency channels available done as a part of a separate study, can give a measure of the overall system capacity. This study shows sufficient availability (for acceptable blockage levels for worst case traffic loads. It is found that overall the voice communications will reduce the system availability the most, followed by Management accessing portion of the data which turns limits the CPDLC capability.

Shamma, Mohammed A.↗
NASA NTRS1998

Open Architecture Data System for NASA Langley Combined Loads Test System

The Combined Loads Test System (COLTS) is a new structures test complex that is being developed at NASA Langley Research Center (LaRC) to test large curved panels and cylindrical shell structures. These structural components are representative of aircraft fuselage sections of subsonic and supersonic transport aircraft and cryogenic tank structures of reusable launch vehicles. Test structures are subjected to combined loading conditions that simulate realistic flight load conditions. The facility consists of two pressure-box test machines and one combined loads test machine. Each test machine possesses a unique set of requirements or research data acquisition and real-time data display. Given the complex nature of the mechanical and thermal loads to be applied to the various research test articles, each data system has been designed with connectivity attributes that support both data acquisition and data management functions. This paper addresses the research driven data acquisition requirements for each test machine and demonstrates how an open architecture data system design not only meets those needs but provides robust data sharing between data systems including the various control systems which apply spectra of mechanical and thermal loading profiles.

Lightfoot, Michael C.↗
NASA NTRS1974

Hightip-speed, low-loading transonic fan stage. Part 2: Data compilation

Tests were conducted on a high-tip-speed low-loading transonic fan stage to determine the performance and inlet flow distortion tolerance of the design. Test data were recorded for overall and blade element performance with both uniform and distorted inlet flows. A tabular summary of the data and a representative selection of the computer data reduction sheets are presented.

Ware, T. C.↗
NASA NTRS1991

Experimental investigation of helicopter vibration reduction using rotor blade aeroelastic tailoring

A wind tunnel investigation has been conducted to parametrically investigate the effect of blade nonstructural mass on helicopter fixed- and rotating-system vibratory loads. The data were obtained using Mach- and aeroelastically-scaled model rotor blades which allowed for the addition of concentrated nonstructural masses at multiple points along the blade radius. Testing was conducted for advance ratios ranging from 0.10 to 0.35 for ten blade mass configurations. Three thrust levels were obtained at representative full-scale shaft angles for each configuration. Results indicate that proper placement of blade nonstructural mass can provide reductions in fixed-system vibratory loads, but that correct mass placement and the loads reduction realized are dependent upon flight condition. The data base obtained with this investigation provides a comprehensive set of fixed-system shears and moments, blade moment, and blade flap and lag response. The data set is well suited for use in the correlation and development of advanced rotorcraft analyses.

Wilbur, Matthew L.↗
NASA NTRS2019

ASPIRE Aerodynamic Models and Flight Performance

The Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project waslaunched to develop the capability for testing supersonic parachutes at Mars-relevant conditions.Three initial parachute tests, targeted as a risk-reduction activity for NASA's upcomingMars2020 mission, successfully tested two candidate parachute designs and provided valuabledata on parachute inflation, forces, and aerodynamic behavior. Design of the flight tests dependedon flight mechanics simulations which in turn required aerodynamic models for the payload, andthe parachute. Computational Fluid Dynamics (CFD) was used to generate these models preflightand are compared against the flight data after the tests. For the payload, the reconstructedaerodynamic behavior is close to the pre-flight predictions, but the uncertainties in thereconstructed data are high due to the low dynamic pressures and accelerations during the flightperiod of comparison. For the parachute, the predicted time to inflation agrees well with the preflightmodel; the peak aerodynamic force and the steady state drag on the parachute are withinthe bounds of the pre-flight models, even as the models over-predict the parachute drag atsupersonic Mach numbers. Notably, the flight data does not show the transonic drag decreasepredicted by the pre-flight model. The ASPIRE flight tests provide previously unavailablevaluable data on the performance of a large full-scale parachute behind a slender leading bodyat Mars-relevant Mach number, dynamic pressure and parachute loads. This data is used topropose a new model for the parachute drag behind slender bodies to aid future experiments.

Muppidi, Suman↗
NASA NTRS1989

Three-dimensional aerodynamics of an annular airfoil cascade including loading effects

A series of experiments are described which investigate and quantify the effect of loading on the three-dimensional flow through a subsonic annular cascade of cambered airfoils. At two levels of loading, detailed data quantify the cascade inlet velocity, the intrapassage flow field, the airfoil surface pressure distributions, the exit flow field, and the total pressure loss distributions. Aerodynamic loading is shown to strengthen the radial pressure gradient, the passage vortex structure, the vortex-endwall boundary layer interactions, and the losses.

Fleeter, S.↗
NASA NTRS1983

Loads environment for payload/cargo integration

Space Shuttle users are required to design their payload to the Shuttle loads environment. This loads environment covers mission phases from prelaunch to landing. Transient response loads analyses are required for lift-off and landing events. Other mission events are analyzed statically because they result in payload loads that either change slowly or are lower than lift-off and landing loads. Response data from flight instrumentation located on the orbiter and payloads have been compared to preflight design conditions and to nominal predictions. The results have verified that the design loads envelop flight responses.

Frederick, D. H.↗
NASA NTRS1996

Dynamic Calibration of the NASA Ames Rotor Test Apparatus Steady/Dynamic Rotor Balance

The NASA Ames Rotor Test Apparatus was modified to include a Steady/Dynamic Rotor Balance. The dynamic calibration procedures and configurations are discussed. Random excitation was applied at the rotor hub, and vibratory force and moment responses were measured on the steady/dynamic rotor balance. Transfer functions were computed using the load cell data and the vibratory force and moment responses from the rotor balance. Calibration results showing the influence of frequency bandwidth, hub mass, rotor RPM, thrust preload, and dynamic loads through the stationary push rods are presented and discussed.

Peterson, Randall L.↗
NASA NTRS1984

Role of research aircraft in technology development

NASA supercritical wing technology, and the digital fly-by-wire program are discussed as used on the F-8 research aircraft. Furthermore, the Highly Maneuverable Aircraft Technology (HiMAT) program, using a 0.44-scale, 3500 lb jet-powered remotely piloted research aircraft, is analyzed. Highly accurate data on aerodynamic and structural loads and deflection data were obtained from model flight tests. In addition, an oblique-wing technology is discussed through the example of the piloted AD-1 research aircraft, noting the low cost of the experiment. Other topics include: integrated system technology; generic forces of the research aircraft program; and aeronautical technology application trends.

Szalai, K. J.↗
NASA NTRSDate not supplied

Improvements in VLBI Data Analysis for Advanced in Geodesy

I will provide an overview of advances in VLBI data analysis implemented at NASA GSFC. That include the use of B-splines for modeling non-linear station position evolution, the use of all non-tidal mass loadings in data reduction, the use of slant a priori path delays from the output of numerical weather models, the use of B-splines for evaluation of the Earth orientation parameters as a continuous function, the use of elevation-dependent weighting, processing both 24 hr and 1 hr experiments in a single least square solutions and other innovations. I will show how this changes in data analysis affect space geodesy results, such as estimation of station positions, Earth orientation parameters, and source coordinates.

Leonid Petrov↗