Fluorination Effect on Lithium- and Manganese-Rich Layered Oxide Cathodes
Not Available
25 ENERGY STORAGE↗
SEARCH · Engineering Papers
Results for “lithium oxide”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A room temperature rechargeable Li 2 O-based lithium-air battery enabled by a solid electrolyte
Lithium-air batteries have scope to compete with gasoline in terms of energy density. However, in most systems, the reaction pathways either involve one- or two-electron transfer, leading to lithium peroxide (Li 2 O 2 ) or lithium superoxide (LiO 2 ), respectively. Kondori et al. investigated a lithium-air battery that uses a ceramic-polyethylene oxide–based composite solid electrolyte and found that it can undergo a four-electron redox reaction through lithium oxide (Li 2 O) formation and decomposition (see the Perspective by Dong and Lu). The composite electrolyte embedded with Li 10 GeP 2 S 12 nanoparticles shows high ionic conductivity and stability and high cycle stability through a four-electron transfer process.
25 ENERGY STORAGE↗
Oxide Fiber Cathode Materials for Rechargeable Lithium Cells
LiCoO2 and LiNiO2 fibers have been investigated as alternatives to LiCoO2 and LiNiO2 powders used as lithium-intercalation compounds in cathodes of rechargeable lithium-ion electrochemical cells. In making such a cathode, LiCoO2 or LiNiO2 powder is mixed with a binder [e.g., poly(vinylidene fluoride)] and an electrically conductive additive (usually carbon) and the mixture is pressed to form a disk. The binder and conductive additive contribute weight and volume, reducing the specific energy and energy density, respectively. In contrast, LiCoO2 or LiNiO2 fibers can be pressed and sintered to form a cathode, without need for a binder or a conductive additive. The inter-grain contacts of the fibers are stronger and have fewer defects than do those of powder particles. These characteristics translate to increased flexibility and greater resilience on cycling and, consequently, to reduced loss of capacity from cycle to cycle. Moreover, in comparison with a powder-based cathode, a fiber-based cathode is expected to exhibit significantly greater ionic and electronic conduction along the axes of the fibers. Results of preliminary charge/discharge-cycling tests suggest that energy densities of LiCoO2- and LiNiO2-fiber cathodes are approximately double those of the corresponding powder-based cathodes.
Rice, Catherine E.↗
Direct Recycling of Blended Cathode Materials by Froth Flotation
We report that direct Li-ion battery recycling involves separating cathode active materials in the solid phase while preserving their electrochemical performance. To reuse the recycled ones in new batteries, it is necessary to separate individual cathode components, which would typically occur prior to the rejuvenation and any compositional reformulation processes. Herein, a froth flotation process is developed to separate pristine lithium nickel-manganese-cobalt oxide (LiNi 0.333 Mn 0.333 Co 0.333 O 2 , NMC111) and lithium manganese oxide (LMO) materials. The flotation results show that with multiple stages of the separation processes, a satisfactory separation is achieved with 95% grade or above of NMC111 in the froth product and 95% grade of LMO in the tailing product. The electrochemistry results show that the flotation chemicals have negligible impact on the electrochemical performance of recycled active materials, whereas the NMC111 exhibits a minor capacity fade after being in contact with deionized water at 2% solid concentration. An improvement in both the rate and cycling performance is achieved at 10% solid concentration or higher. It is found that there is little compositional and structural change to the aqueous recycled NMC111 powders. An effective and low-cost separation method for direct recycling mixed cathode compositions is demonstrated.
25 ENERGY STORAGE↗
Sintered Cathodes for All-Solid-State Structural Lithium-Ion Batteries
All-solid-state structural lithium ion batteries serve as both structural load-bearing components and as electrical energy storage devices to achieve system level weight savings in aerospace and other transportation applications. This multifunctional design goal is critical for the realization of next generation hybrid or all-electric propulsion systems. Additionally, transitioning to solid state technology improves upon battery safety from previous volatile architectures. This research established baseline solid state processing conditions and performance benchmarks for intercalation-type layered oxide materials for multifunctional application. Under consideration were lithium cobalt oxide and lithium nickel manganese cobalt oxide. Pertinent characteristics such as electrical conductivity, strength, chemical stability, and microstructure were characterized for future application in all-solid-state structural battery cathodes. The study includes characterization by XRD, ICP, SEM, ring-on-ring mechanical testing, and electrical impedance spectroscopy to elucidate optimal processing parameters, material characteristics, and multifunctional performance benchmarks. These findings provide initial conditions for implementing existing cathode materials in load bearing applications.
Ceramics↗
Impact of surface coating on electrochemical and thermal behaviors of a Li-rich Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 cathode
Lithium-rich layered oxide materials are considered as potential cathode materials for future high-performance lithium-ion batteries (LIBs) owing to their high operating voltage and relatively high specific capacity. However, perceptible issues such as poor rate performance, poor capacity retention, and voltage degradation during cycling need to be improved before the successful commercialization of the material. In this report, zirconia coated Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 2 = 1.0, 1.5 and 2.0 wt%) materials are synthesized using a sol–gel assisted ball milling approach. A comparison of structural, morphological and electrochemical properties is examined to elucidate the promising role of ZrO 2 coating on the performance of the NMC cathode. A uniform and homogeneous ZrO 2 coating is observed on the surface of NMC particles as evident by TEM elemental mapping images. The ZrO 2 coated NMCs exhibit significantly improved electrochemical performance at a higher C-rate as compared to pristine material. 1.5% ZrO 2 coated NMC demonstrates better cycling stability (95% capacity retention) than pristine NMC (77% capacity retention) after 50 cycles. All ZrO 2 coated NMC materials demonstrated improved thermal stability compared to pristine material. The difference in onset temperature of 2 wt% ZrO 2 coated and pristine NMC is 20 °C. The improved electrochemical performance of ZrO 2 coated NMC can be attributed to the stabilization of its surface structure due to the presence of ZrO 2 .
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Lithium-Ion Battery Materials as Tunable, “Redox Non-Innocent” Catalyst Supports
The development of general strategies for the electronic tuning of a catalyst’s active site is an ongoing challenge in heterogeneous catalysis. To this end, herein, we describe the application of Li-ion battery cathode and anode materials as redox non-innocent catalyst supports that can be continuously modulated as a function of lithium intercalation. A zero-valent nickel complex was oxidatively grafted onto the surface of lithium manganese oxide (Li x Mn 2 O 4 ) to yield isolated Ni2+ occupying the vacant interstitial octahedral site in the Li diffusion channel on the surface and subsurface of the spinel structure (Ni/Li x Mn 2 O 4 ). Additionally, the activity of Ni/Li x Mn 2 O 4 for olefin hydrogenation, as a representative probe reaction, was found to increase monotonically as a function of support reductive lithiation. Simulation of Ni/Li x Mn 2 O 4 reveals the dramatic impact of surface redox states on the viability of the homolytic oxidative addition mechanism for H 2 activation. Catalyst control through support lithiation was extended to an organotantalum complex on Li x TiO 2 , demonstrating the generality of this phenomenon.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A mechanistic study of mesoporous TiO 2 nanoparticle negative electrode materials with varying crystallinity for lithium ion batteries
Nanoscale oxide-based negative electrodes are of great interest for lithium ion batteries due to their high energy density, power density and enhanced safety. In this work, we conducted a case study on mesoporous TiO 2 nanoparticle negative electrodes with uniform size and varying crystallinity in order to investigate the trend in the electrochemical properties of oxide-based nanoscale negative electrodes with varying crystallinity. Furthermore, mesoporous solid spherical TiO 2 nanoparticles with a uniform particle size and varying crystallinity, i.e. , amorphous TiO 2 (A-TiO 2 ), partially crystalline TiO 2 (PC-TiO 2 ) and fully crystalline TiO 2 (FC-TiO 2 ) nanoparticles were studied. At low current rate (quasi steady-state), the specific capacity of the samples drops with the decrease of crystallinity. Ex situ synchrotron pair distribution function analysis reveals that the 1D zigzag Li ion diffusion pathway becomes expanded with the increase of crystallinity, which promotes ion mobility and charge storage. At high current rates (away from equilibrium states), however, the A-TiO 2 sample demonstrates slightly larger capacity than the FC-TiO 2 sample, both of which show larger capacities than that of the PC-TiO 2 sample. Both A-TiO 2 and FC-TiO 2 samples exhibit higher capacitive contribution to the charge storage and larger Li + diffusivity than those of the PC-TiO 2 sample, which explains their better rate capability. Moreover, the larger Li + diffusivity of the A-TiO 2 sample leads to the slightly larger specific capacity than the FC-TiO 2 sample at the highest current rate.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Single-crystal NMC622 from combustion-assisted solid-state synthesis: Tunable particle size, voltage-dependent stability, and Li-ion diffusion
Cost-effective and scalable synthesis of single-crystal lithium–metal-oxide cathodes with controlled size and morphology remains challenging for advancing high-performance lithium-ion batteries. Here, we demonstrate a solution combustion–assisted solid-state method for producing single-crystal NMC622 with tunable particle size at various lithium stoichiometries. Structural and electronic characteristics were probed using synchrotron-XANES, EXAFS, XRD and XPS, confirming well-defined coordination environments and phase purity up to Li ≈ 1.3. The electrochemical behavior of LixNMC (x = 1.0 and 1.3) single crystals was evaluated across 2.8–4.3 V and 2.8–4.7 V windows to elucidate the effects of lithium content and operating voltage. At 2.8–4.3V, Li1.3NMC exhibits higher initial capacity due to its larger lithium inventory, while Li1.0NMC shows superior long-term retention driven by its larger crystal size and reduced structural distortion. Increasing the cutoff voltage to 4.7 V enhances the initial capacity of both compositions by 17–25%, but long-term capacity retention ultimately converges to values comparable to those at 4.3 V due to voltage-induced degradation, where Li+ diffusion constant remains lying ranging from 10−12 –10−11 cm2s−1. Overall, this study establishes a scalable combustion-assisted route for synthesizing tunable single-crystal NMC622 and highlights the interplay between lithium stoichiometry, particle size, and voltage window in governing cathode stability.
Roy, Subrata C [Jackson State University]↗
Current Status and Future Directions of All-Solid-State Batteries with Lithium Metal Anodes, Sulfide Electrolytes, and Layered Ternary Oxide Cathodes
All-solid-state batteries (ASSBs) offer great promise as a next-generation energy storage technology with higher energy density, wider operating temperature range, and improved safety for electric vehicles. ASSBs employing lithium metal anodes (Li), sulfide-based solid-state electrolytes (SSE), and Ni-rich layered transition metal oxide cathodes (LiMO 2 , M = Ni, Mn, Co, Al) are particularly promising due to its superior electrochemical performance compared to other solid-electrolyte systems. However, the battery cycle life at high cathode mass loading and high current is still limited because the failure mechanism is not fully understood. Lithium dendrite growth at the anode or inside a solid electrolyte still represents as a serious risk of cell failure. Interfacial resistance increases attributed to electrolyte decomposition and interfacial void formation at both cathode–electrolyte and anode–electrolyte interfaces lead to gradual capacity fading. In this Review, we present the fundamental challenges and recent scientific understandings of each component in ASSBs. The novel diagnostic tools for these components, especially the interfaces buried under the surface that are often hard for characterization are mainly examined. Lastly, we offer a perspective for future research directions. We hope this Review will provide a timely snapshot of state-of-the-art research progress in ASSBs to accelerate the development of ASSBs.
25 ENERGY STORAGE↗
3D Carbon Coating Enabled High‐capacity and Stable Micro‐sized Silicon Suboxide‐graphite Blended Anodes for Practical Lithium‐ion Batteries
Abstract Silicon oxide (SiO x ) is a promising anode candidate of lithium‐ion batteries (LIBs) owing to its extremely high specific capacity. However, the low initial Coulombic efficiency (ICE) and rapid capacity degradation of SiO x , triggered by the enormous volume variation upon repeated (de)lithiation, gravely hinder its practical use. Herein, two mass‐produced micro‐sized SiO x @C composites with obviously different morphologies for commercial LIBs are reported. Particularly, the SiO x ‐graphite blended anode (SiO x @3D‐G‐Gr) based on SiO x wrapped by three‐dimensional (3D) carbon layers (SiO x @3D‐G) exhibits a capacity of 519 mAh g −1 , an ICE of 90.0 % and a capacity retention of 83.4 % at 0.2 C over 100 cycles. which is far exceeding its counterpart SiO x @C‐H‐Gr (65.7 %). The obtained impressive properties of SiO x @3D‐G originate from the critical contribution of 3D carbon layers, which serves as the effective stress buffer and protective layer as well as the strong networks for electron/Li + transport. Accordingly, the full‐cell based on SiO x @3D‐G‐Gr anode and commercial LiCoO 2 cathode delivers a capacity of 803 mAh and an excellent capacity retention of 95.6 % (616 mAh, 96.6 % for graphite, respectively) at 1 C over 100 cycles with a stabilized CE of nearly 100 %. The micro‐sized SiO x @3D‐G showing a promising prospect in the commercial‐grade anodes in LIBs.
Electrochemistry↗
Toward a high-voltage fast-charging pouch cell with TiO 2 cathode coating and enhanced battery safety
Nickel-rich layered lithium transition metal oxides, LiNi x Co y Mn 1-x-y O 2 , are key cathode materials for high-energy lithium-ion batteries owing to their high specific capacity. However, the commercial deployment of nickel-rich oxides has been hampered by their poor thermostability and insufficient cycle life. In this work full batteries with uncoated and TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathodes and graphite anodes are compared in terms of electrochemical performance and safety behavior. The battery using a TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode exhibited better cyclic performance at high cutoff voltage. Electrochemical impedance spectroscopy analysis indicated that the TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode gave the battery a more stable charge transfer resistance. Transmission electron microscopy demonstrated that TiO 2 coating reduced accumulation of the cathode electrolyte interface layer on the particle surface. Time-of-flight secondary ion mass spectrometry demonstrated that TiO 2 coating markedly enhanced the interface stability of the cathode particle and protected the particle from serious etching by the electrolyte. Accelerating rate calorimetry revealed that the trigger temperature of thermal runaway for the battery using TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 as cathode material was 257 °C, which was higher than that of the battery with the uncoated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode (251 °C). In situ X-ray diffraction during heating demonstrated that this enhanced safety can be attributed to the suppressed phase evolution of the coated cathode material.
25 ENERGY STORAGE↗
Constructing O2/O3 homogeneous hybrid stabilizes Li-rich layered cathodes
With the advantages of high energy density and low manufacture cost, lithium-rich layered oxides (LLOs), typically with a layered O3-type structure, are regarded as promising cathodes for lithium-ion batteries (LIBs), but their broad usages are hindered by severe voltage decay over cycling. Although recent progress in O2-type LLOs has aroused interest for their less voltage decay, the critical barrier of unsatisfactory capacity retention has not been overcome yet. In this work, to tackle these handicaps, we design a new type of LLO (O2/O3-type LLO) with a homogeneous hybrid structure, where the O2 and O3 lattice stacking sequences are arranged alternatively. Benefitting from this novel O2/O3 hybrid structure, the designed material shows greatly improved voltage and capacity stability than that of pure O2- and O3-type LLOs. Revealed by in-situ synchrotron X-ray diffraction and operando differential electrochemical mass spectra, the O2/O3-hybrid LLO cathode shows a more reversible structural evolution, smaller volume change and suppressed oxygen loss during the electrochemical processes. Our approach has initiated a new way to reduce the capacity and voltage decay of LLOs, which endows great promise to the development of high-energy-density LIBs.
25 ENERGY STORAGE↗
Electrochemical Oxidation in Garnet-Type Solid Electrolyte by Formation of Point Defects
All-solid-state batteries hold greater promise for improving safety and energy density over conventional battery technology employing organic liquid electrolytes. One of the required features of a Li + conducting solid electrolyte is electrochemical stability, attained thermodynamically or kinetically, within the targeted operating voltage and temperature ranges. Therefore, understanding of the oxidative or reductive degradation mechanism is important to allow the design of stable solid electrolyte materials. This work contributes to building an understanding of the oxidative degradation mechanism in lithium solid electrolytes at cell operating conditions. Here, we have focused on resolving the oxidative decomposition mechanism of Al-doped lithium garnet Li 6.28 Al 0.24 La 3 Zr 2 O 12 (LLZO) as a state-of-the-art inorganic ceramic electrolyte. By combining experimental and computational analyses, we show that oxidation of LLZO occurs by simultaneous loss of oxygen and lithium from the structure, resulting in substoichiometric LLZO, at a moderate temperature (80 °C) and a high electrode potential (4.3 V vs Li/Li + ). Based on X-ray absorption and diffraction analyses, we find that the zirconium coordination shells in LLZO contract while the crystal structure experiences positive chemical strain upon electrochemical oxidation. The results from ex situ structural characterization of both the local structure and crystal symmetry are supported by a substoichiometric LLZO with lithium and oxygen vacancies, modeled by density functional theory (DFT) calculations. These chemical and structural changes in LLZO suppress effective lithium-ion conductivity by an order of magnitude. Formation of lithium and oxygen vacancies in LLZO upon electrochemical oxidation is different from prior thermodynamic predictions of phase decomposition of LLZO. The difference here is that the experiments were conducted at near-room temperature, which can hinder the kinetics of phase separation, and thus, the resultant LLZO solid electrolyte is still single-phase but substoichiometric in Li and O. In conclusion, these findings contribute an important degradation mechanism of the electrolyte, relevant for practical operational conditions of solid-state batteries.
36 MATERIALS SCIENCE↗
Lithium ion cells with high performance electrolyte and silicon oxide active materials achieving very long cycle life performance
Improved negative electrodes can comprise a silicon based active material blended with graphite to provide more stable cycling at high energy densities. In some embodiments, the negative electrodes comprise a blend of polyimide binder mixed with a more elastic polymer binder with a nanoscale carbon conductive additive. Electrolytes have been formulated that provide for extended cycling of cells incorporating a mixture of a silicon-oxide based active material with graphite active material in negative electrodes that can be matched with positive electrodes comprising nickel rich lithium nickel manganese cobalt oxides to cells with unprecedented cycling properties for large capacity cell based on a silicon negative electrode active material.
Dong, Yingnan↗
Crossover Effects in Lithium–Metal Batteries with a Localized High Concentration Electrolyte and High–Nickel Cathodes
While crossover effects, such as transition–metal dissolution, are well–understood in lithium–ion batteries, there is a limited understanding of the effect of crossed–over chemical species in cells with oxide cathodes and lithium–metal anodes. In this work, the effects of cathode–to–anode and anode–to–cathode crossover are explored in cells with a high–nickel cathode, lithium–metal anode, and a localized high–concentration electrolyte (LHCE). Dramatic differences are found among cells; a lithium–metal anode paired with a high–nickel cathode has three times less solid–electrolyte interphase growth than a lithium–metal anode paired with lithium metal. Meanwhile, the cathode paired with lithium metal has 2–3 times higher capacity fade than the same cathode paired with graphite. Decomposition and crossover of the FSI salt is identified as the main source of these changes. The fluorine in the salt is first stripped off at the lithium–metal anode, and the remaining sulfur and nitrogen cross over to the cathode. Although the reduction in fluorine content harms the surface stability of the cathode, the lithium–metal anode benefits from the increased fluorine content. Furthermore, because the lithium–metal anode is typically the bottleneck for cells with thin lithium, crossover is a major factor in the enhanced performance of lithium–metal batteries with LHCE.
25 ENERGY STORAGE↗
Cation-Driven Assembly of Bilayered Vanadium Oxide and Graphene Oxide Nanoflakes to Form Two-Dimensional Heterostructure Electrodes for Li-Ion Batteries
Lithium preintercalated bilayered vanadium oxide (LVO or δ-Li x V 2 O 5 ·nH 2 O) and graphene oxide (GO) nanoflakes were assembled using a concentrated lithium chloride solution and annealed under vacuum at 200 °C to form two-dimensional (2D) δ-Li x V 2 O 5 ·nH 2 O and reduced GO (rGO) heterostructures. Here we found that the Li + ions from LiCl enhanced the oxide/carbon heterointerface formation and served as stabilizing ions to improve structural and electrochemical stability. The graphitic content of the heterostructure could be easily controlled by changing the initial GO concentration prior to assembly. We found that increasing the GO content in our heterostructure composition helped inhibit the electrochemical degradation of LVO during cycling and improved the rate capability of the heterostructure. A combination of scanning electron microscopy and X-ray diffraction was used to help confirm that a 2D heterointerface formed between LVO and GO, and the final phase composition was determined using energy-dispersive X-ray spectroscopy and thermogravimetric analysis. Scanning transmission electron microscopy and electron energy-loss spectroscopy were additionally used to examine the heterostructures at high resolution, mapping the orientations of rGO and LVO layers and locally imaging their interlayer spacings. Further, electrochemical cycling of the cation-assembled LVO/rGO heterostructures in Li-ion cells with a non-aqueous electrolyte revealed that increasing the rGO content led to improved cycling stability and rate performance, despite slightly decreased charge storage capacity. The heterostructures with 0, 10, 20, and 35 wt % rGO exhibited capacities of 237, 216, 174, and 150 mAh g –1 , respectively. Moreover, the LVO/rGO-35 wt % and LVO/rGO-20 wt % heterostructures retained 75% (110 mAh g–1) and 67% (120 mAh g –1 ) of their initial capacities after increasing the specific current from 20 to 200 mA g –1 , while the LVO/rGO-10 wt % sample retained only 48% (107 mAh g –1 ) of its initial capacity under the same cycling conditions. In addition, the cation-assembled LVO/rGO electrodes exhibited enhanced electrochemical stability compared to electrodes prepared through physical mixing of LVO and GO nanoflakes in the same ratios as the heterostructure electrodes, further revealing the stabilizing effect of a 2D heterointerface. The cation-driven assembly approach, explored in this work using Li + cations, was found to induce and stabilize the formation of stacked 2D layers of rGO and exfoliated LVO. The reported assembly methodology can be applied for a variety of systems utilizing 2D materials with complementary properties for applications as electrodes in energy storage devices.
25 ENERGY STORAGE↗
Power sources for search and rescue 406 MHz beacons
The results of a study directed at the selection of a commercially available, safe, low cost, light weight and long storage life battery for search and rescue (Sarsat) 406 MHz emergency beacons are presented. In the course of this work, five electrochemical systems (lithium-manganese dioxide, lithium-carbon monofluoride, lithium-silver vanadium oxide, alkaline cells, and cadmium-mercuric oxide) were selected for limited experimental studies to determine their suitability for this application. Two safe, commercially available batteries (lithium-manganese dioxide and lithium-carbon monofluoride) which meet the near term requirements and several alternatives for the long term were identified.
Attia, Alan I.↗