Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Influence of alloy solidification path on melt pool behavior in additive manufacturing

Numerical models used to study transport phenomena in laser-powder bed fusion processes often rely on assumptions and simplifications to reduce their computational expense. One common simplification is in the description of latent heat evolution during the solid-liquid phase change (i.e., the solidification pathway), justified by the fact that the mushy zone thickness is similar to the numerical grid spacing used for continuum transport models. The lack of resolution of transport phenomena in the mushy zone motivates the use of computationally convenient solidification paths such as linear or sigmoidal relationships over pathways derived from fundamental solidification theory such as equilibrium or Scheil models. In the present work, an uncertainty quantification (UQ) framework is used to analyze the influence of solidification pathway selection on the solidification dynamics and melt pool geometries in laser based additive manufacturing (AM) of IN625. Results show the solidification pathway has a quantifiable influence on the cooling rate at the liquidus isotherm, mushy zone thickness, and solidification time. Due to similarities in the latent heat evolution at the beginning of solidification, the equilibrium and Scheil models predict similar cooling rates near the liquidus isotherm, however the wider freezing range of Scheil leads to a wider mushy zone compared to equilibrium. The non-physical latent heat release profiles of sigmoidal and linear paths lead to significant overpredictions of cooling rates at the liquidus isotherm compared to equilibrium and Scheil. Finally, these results indicate that careful consideration should be given to the choice of solidification pathway to ensure reliable model predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrafast x-ray detection of low-spin iron in molten silicate under deep planetary interior conditions

The spin state of Fe can alter the key physical properties of silicate melts, affecting the early differentiation and the dynamic stability of the melts in the deep rocky planets. The low-spin state of Fe can increase the affinity of Fe for the melt over the solid phases and the electrical conductivity of melt at high pressures. However, the spin state of Fe has never been measured in dense silicate melts due to experimental challenges. We report detection of dominantly low-spin Fe in dynamically compressed olivine melt at 150 to 256 gigapascals and 3000 to 6000 kelvin using laser-driven shock wave compression combined with femtosecond x-ray diffraction and x-ray emission spectroscopy using an x-ray free electron laser. The observation of dominantly low-spin Fe supports gravitationally stable melt in the deep mantle and generation of a dynamo from the silicate melt portion of rocky planets.

58 GEOSCIENCES↗
DOE OSTI2022

Fabrication of silicon-tipped fiber-optic temperature sensors using aerogel-assisted glass soldering with precise laser heating

We demonstrate the fabrication of fiber-optic Fabry–Perot interferometer (FPI) temperature sensors by bonding a small silicon diaphragm to the tip of an optical fiber using low melting point glass powders heated by a 980 nm laser on an aerogel substrate. The heating laser is delivered to the silicon FPI using an optical fiber, while the silicon temperature is being monitored using a 1550 nm white-light system, providing localized heating with precise temperature control. The use of an aerogel substrate greatly improves the heating efficiency by reducing the thermal loss of the bonding parts to the ambient environment. A desirable temperature for bonding can be achieved with relatively small heating laser power. The bonding process is carried out in an open space at room temperature for convenient optical alignment. The precise temperature control ensures minimum perturbation to the optical alignment and no induced thermal damage to the optical parts during the bonding process. For demonstration, we fabricated a low-finesse and high-finesse silicon FPI sensor and characterized their measurement resolution and temperature capability. The results show that the fabrication method has a good potential for high-precision fabrication of fiber-optic sensors.

Sheng, Qiwen↗
DOE OSTI2023

Microstructural evolution of rapidly solidified hypoeutectic Al 10Cu alloy during non-isothermal annealing transients induced by nano-second laser pulses

The evolution of characteristic nonequilibrium features presenting in morphologically distinct regions of rapid solidification (RS) microstructures in a hypoeutectic Al—10Cu (atomic %) in response to non-isothermal annealing transients has been studied by transmission electron microscopy (TEM). The capabilities of the Movie-Mode Dynamic TEM (MM-DTEM) instrument were used to expose select regions of the RS microstructure to sequences of rapid heating and cooling transients induced by nanosecond laser pulses while permitting in-situ observation. Partial melting, microstructural scale coarsening, morphological changes of the nonequilibrium features in the multi-phase RS microstructure, and solid-state phase transformation were observed. Heterogeneous nucleation of nanoscale θ-Al 2 Cu phase involved metastable supersaturated α-Al and the θ'-Al 2 Cu phases, establishing different sets of orientation relationships for the stable θ-Al 2 Cu and α-Al phases. Replacement of banded morphology grains that formed under conditions driven farthest from equilibrium by an equiaxed nanocrystalline structure comprised of α-Al phase, the primary solidification product, and an intergranular network of Al 2 Cu crystals has been attributed to local remelting. Here the experimental approach explored, permitted discovery of mechanistic details of location-specific transformation pathways activated in the multi-phase RS microstructure of hypoeutectic Al—Cu during subsequent nonisothermal transients.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Establishing a process-structure-property-performance framework for SLS additive manufacturing through integrated multiscale modeling

This study presents a comprehensive suite of high-fidelity computational models that integrate multiscale and multiphysics simulations to capture the full Selective Laser Sintering (SLS) additive manufacturing process—from initial melting and solidification to mechanical response under external loads. Process simulations are linked with mechanical analysis through Representative Volume Elements (RVEs), establishing a process-structure–property-performance framework. The interaction between laser light and polyamide 12 (PA12) powder is modeled, accounting for laser characteristics and the optical, thermal, and geometrical properties of the powder. The heat source is incorporated into a heat transfer model, coupled with crystallization kinetics and densification models to predict material density and crystallinity. The porosity distribution from the densification model and crystallinity interpolated from experimental data are used to construct the RVEs. A multi-mechanism constitutive model is then calibrated using mechanical tests to predict the stress–strain response. Simulation results show good agreement with experimental data in terms of porosity, crystallinity, and mechanical performance when sufficient laser power (62 W or higher) is used. This research supports the inverse design of 3D-printed structures by introducing a high-fidelity framework that combines multiscale and multiphysics modeling with experimental calibration for predictive and performance-driven additive manufacturing.

SLS↗
DOE OSTI2025

Revealing mechanisms of processing defect mitigation in laser powder bed fusion via shaped beams using high-speed X-ray imaging

The laser powder bed fusion (LPBF) process utilizing a focused Gaussian-shaped beam faces challenges, including pore formation, melt pool fluctuation and liquid spattering. While beam shaping technology has been explored as a potential approach for defect mitigation, the beam-matter interaction dynamics during melting with shaped beams remain unclear. Here, we report the direct observation of ring-shaped beam-matter interaction dynamics, including pore formation, melt pool fluctuation and liquid spattering, and unveil defect mitigation mechanisms in ring-shaped beam laser powder bed fusion process. Here, we find that, by spatially manipulating incident laser rays, the ring-shaped beam controls keyhole morphology, thereby managing the distribution of the reflected rays. This manipulation can effectively eliminate the formation of an unstable cavity at the keyhole tip, stabilizing the keyhole and mitigating keyhole pores. This enhanced keyhole stability effectively reduces the melt pool fluctuation, the formation of liquid breakup induced spatters and liquid droplet colliding induced large spatters in the laser powder bed fusion process. Additionally, the high-energy forefront of the ring-shaped beam effectively melts the powder bed, reducing agglomeration liquid spatter in the laser powder bed fusion process. The discovered defect mitigation mechanisms may guide the design of beam shaping strategies for simultaneously increasing the quality and productivity of metal additive manufacturing.

Beam shaping↗
DOE OSTI2026

Which way does the dendrite grow? Competition among epitaxy, preferred growth direction, and thermal gradients in powder bed fusion additive manufacturing

The as-processed microstructure of metal alloy parts manufactured through laser powder bed fusion (LPBF) is heavily derived from the cellular dendritic solidification. The growth direction of dendrites within the melt pool is determined through competition among epitaxial growth, preferred growth directions, and maximum thermal gradients. However, the dominant factor and the specific role of each in developing melt pool microstructures remain unknown. Here, in this study, we performed single laser track scans on an SS316L single crystal substrate and combined experimental characterization of microstructure and crystal orientations with Computational Fluid Dynamics simulations of thermal gradients to evaluate the role of each factor in determining dendritic growth direction and evolution. Our results reveal that epitaxial growth dominates microstructure development by preferentially growing along a single 〈100〉 variant of the single crystal substrate adjacent to the melt pool boundary. Under LPBF’s highly curved and rapidly evolving thermal field, this preferential dendrite variant selection and its continued growth from the melt pool boundary to the centerline are governed by the local temperature gradient magnitude at the solid-liquid interface, rather than by the instantaneous maximum temperature gradient direction alone. Using these findings, we successfully predict changes in the dendrite growth direction with changing laser scan direction on a single crystal substrate, and show that the geometric melt pool centerline can deviate from the microstructural centerline because asymmetric local temperature gradient magnitudes transiently limit growth, resulting in different dendrite travel distances on each side of the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Selective Deposition and Fusion of AISI 316L: An Additive Manufacturing Process for Space Environments via Direct Ink Writing and Laser Processing

Unlocking the potential of additive manufacturing (AM) for space exploration hinges on overcoming key challenges, notably the ability to manufacture or repair parts on-site during exploration missions with consideration of quality, feedstock utilization, and challenges involved in microgravity environments. While there are multiple efforts to investigate the use of existing metal AM processes such as powder bed fusion (PBF), directed energy deposition (DED), and filament-based material extrusion, each process comes with a different set of challenges in space environments. Here, in this work, we introduce a new AM method that integrates the benefits of direct ink writing (DIW) to selectively deposit metallic pastes with laser-based processing to locally debind and subsequently melt and fuse metal powder, layer by layer, enabling the manufacturing of AISI 316L samples with densities exceeding 99.0%. The impact of process parameters on single-track dimensions, surface morphology, and porosity was characterized. The efficacy of laser debinding was assessed via secondary-ion mass spectrometry, permitting the carbon content to be estimated at 0.0152%, which is safely below the acceptable limit (0.03 wt%) for AISI 316L.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shock compression of silver to 300 GPa: Wave profile measurements and melting transition

Recent in-situ x-ray diffraction (XRD) measurements on laser-shock compressed Ag foils demonstrated a face-centered-cubic to body-centered-cubic transformation at ~150 GPa and melting between 172 and 197 GPa [Phys. Rev. Lett. 124, 235701 (2020)]. As a complement to the XRD work, we conducted plate impact experiments to obtain shock velocity and wave profile measurements on thicker Ag samples shock-compressed to peak stresses between 30 and 300 GPa. The shock velocity–particle velocity results were fitted very well by a linear relation over the entire stress range, providing an accurate determination of the Ag Hugoniot (locus of the stress-volume states achieved under shock compression). For peak stresses below 187 GPa and above 210 GPa—corresponding to the solid and liquid phases, respectively—the wave profiles show clean single waves. No wave profile features related to the fcc-bcc transformation at ~150 GPa were observed, implying minimal volume change for the transformation. For stresses between 187 and 210 GPa, an initial jump was followed by a time-dependent increase in the particle velocity (20–80 ns risetime) to the peak state—corresponding to the solid-liquid mixed phase response. Unlike the solid and liquid response, the mixed-phase response cannot be readily analyzed analytically. Instead, numerical simulations incorporating an accurate multiphase equation of state for Ag—not currently available—are required to analyze the wave profiles measured at 187–210 GPa stresses. Furthermore, the present work shows the potential for using wave profile measurements to examine the melting transition under shock compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Electronic Melting of Silicon in Nanostructures using X-ray Forbidden Bragg Reflections

Abstract We carried out a short beamtime at the Pohang Accelerator Laboratory x-ray Free Electron Laser to perform a pump-probe (PP) laser excitation diffraction experiment on the silicon (222) forbidden Bragg peak. To limit the x-ray penetration, we used a “device layer” silicon film wafer bonded to a silicon substrate. The sample, specially fabricated by MEMC Electronic Materials, had a Si(100) substrate bonded to a 170 nm Si(100) film rotated at 45° for crystallographic isolation. A second sample was reactive-ion-etched down to 52 nm thickness. In the silicon lattice, the covalent bonds are seen exclusively at the 222 reflection. Upon laser excitation, these electrons are expected to be excited to the valence band on femtosecond electronic time scales. The Si(222) reflection is therefore expected to be extinguished on this fast time scale, while the electron–phonon coupled acoustic response is determined by the lattice dynamics. The latter is determined by the speed of sound over the device thickness, which is in the mid-picosecond range.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Sensitivity of additively manufactured AA7075 to variation in feedstock composition and print parameters

Here we developed a combined finite element and CALPHAD based model of the Laser Powder Bed Fusion (LPBF) process for AA7075 alloy that considers the effect of feedstock composition and print parameters. A single-pass of a laser on a layer of AA7075 alloy powder has been considered. Sensitivity of temperature evolution and melt pool geometry to variation in the stoichiometry of the feedstock powder and laser source characteristics have been studied. Our results indicate that deviation (up to 10%) of the feedstock composition from the AA7075 raises the maximum temperature and increases melt pool size. Excess Cu content shows the largest melt pool width and depth among all the cases. The peak temperature is higher than the standard feedstock composition in all cases, except when the Cu concentration is reduced. Increasing the scan power also results in a higher peak temperature and a larger melt pool size. Furthermore, the temperature's rise time increases by lowering the scan speed.

42 ENGINEERING↗
DOE OSTI2020

Laser-metal interaction dynamics during additive manufacturing resolved by detection of thermally-induced electron emission

In situ monitoring is required to improve the understanding and increase the reliability of additive manufacturing methods such as laser powder bed fusion (LPBF). Current diagnostic methods for LPBF capture optical images, X-ray radiographs, or measure the emission of thermal or acoustic signals from the component. Herein, a methodology based on the thermal emission of electrons - thermionic emission - from the metal surface during LPBF is proposed which can resolve laser-material interaction dynamics. The high sensitivity of thermionic emission to surface temperature and surface morphology is revealed to enable precise determination of the transition between conduction and keyhole mode melting regimes. Increases in thermionic emission are correlated to laser scanning conditions that give rise to pore formation and regions where surface defects are pronounced. The information presented here is a critical step in furthering our understanding and validation of laser-based metal additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Hydrogen on the Phase Relations in Fe-FeS at Pressures of Mars-Sized Bodies

The large radius, and therefore low density, of the Martian core found in the InSight mission data analysis highlights the importance of considering other light elements besides sulfur (S), which has been considered as the main light element for Mars for decades. Hydrogen (H) is abundant in the solar system and becomes siderophile at high pressures. Although Fe-S and Fe-H systems have been studied individually, the Fe-S-H ternary system has only been investigated up to 16 GPa and 1723 K. We have investigated the Fe-S-H system at pressures and temperatures (P-T) relevant to the cores of Mars-sized planets (up to 45 GPa and well above the melting temperature of FeS) in the laser-heated diamond anvil cell combined with in situ synchrotron X-ray diffraction. Here we found that sufficient hydrogen leads to the disappearance of Fe 3 S at high P-T. Instead, separate Fe-H and Fe-S phases appear at 23–35 GPa. At pressures above 35 GPa, we found a new phase appearing while Fe-S phases disappear and Fe-H phases remain. Our analysis indicates that the new phase likely contains both S and H in the crystal structure (tentatively FeS x H y where x ≈ 1 and y ≈ 1). The observed pressure-dependent changes in the phase relation may be important for understanding the structure and dynamics of the Martian core and the cores of Mars-sized exoplanets.

58 GEOSCIENCES↗
DOE OSTI2020

Investigating off-Hugoniot states using multi-layer ring-up targets

Abstract Laser compression has long been used as a method to study solids at high pressure. This is commonly achieved by sandwiching a sample between two diamond anvils and using a ramped laser pulse to slowly compress the sample, while keeping it cool enough to stay below the melt curve. We demonstrate a different approach, using a multilayer ‘ring-up’ target whereby laser-ablation pressure compresses Pb up to 150 GPa while keeping it solid, over two times as high in pressure than where it would shock melt on the Hugoniot. We find that the efficiency of this approach compares favourably with the commonly used diamond sandwich technique and could be important for new facilities located at XFELs and synchrotrons which often have higher repetition rate, lower energy lasers which limits the achievable pressures that can be reached.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Melting of the Fe–C–H System and Earth's Deep Carbon–Hydrogen Cycle

The occurrences and cycling of slab-originated carbon and hydrogen are considered to be controlled by their reactions with metallic iron from mantle disproportionation and slab serpentinization, to form Fe alloys containing carbon and hydrogen. In this work, we show experimental results on the phase relations and melting of the Fe-C-H system using laser-heated diamond anvil cell and X-ray diffraction techniques up to 72 GPa. The incorporation of hydrogen was found to lower the eutectic melting temperatures of Fe-C alloy by ~50–178 K at 20–70 GPa, facilitating the formation of metallic liquids in the deep mantle and thus enhancing the mobility and deep cycling of subducted carbon and hydrogen. Hydrogen also substitutes with carbon in Fe-C metal to form hydride and diamond at relatively high-temperature conditions (e.g., 42.6 GPa, >1885 K and 71.8 GPa, >1798 K). The hydrogen-carbon-enriched metallic liquids provide the necessary fluid environment for superdeep diamond growth.

58 GEOSCIENCES↗
DOE OSTI2023

Melting line and thermal equation of state of fcc-cobalt: A combined experimental and computational approach

The melting line of cobalt has been investigated both experimentally, using synchrotron X-ray diffraction coupled with laser-heated diamond anvil cells, and theoretically, using ab initio simulations. Over the investigated pressure and temperature range – between 30 and 100 GPa and from ambient temperature up to 4000 K – the hexagonal close-packed structure, stable at ambient conditions, is replaced at high temperature by the face-centered cubic structure, observed stable till melting. The melting temperatures obtained by the two methods are in remarkable agreement and the melting line can be well described by a Simon–Glatzel equation of the form T$_m$ = 1768(K)(P(GPa)/35.62+1) 0.64 . Finally, from the obtained results it was possible to determine a thermal equation of state for the cubic face-centered phase of Co.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ultrafast laser-driven many-body dynamics and Kondo coherence collapse

Ultrafast laser pulse has provided a systematic way to inspect the dynamics of electrons in condensed matter systems. In this paper, by means of time-dependent density matrix renormalization group, we study an ultrafast laser-driven Kondo lattice model, in which conduction electrons are strongly coupled with magnetically local moments. The single-particle spectral function due to strong correlation effects and photon emission in the nonequilibrium states under laser driving are calculated. We find laser field excited collective doublon-hole pairs and an associated transient melting of Kondo coherence phase, signifying the collapse of Kondo energy gap. Moreover, we show that the photon emission, induced by a strong laser field, exhibits a different intensity characteristics than in the equilibrium Kondo insulator, which could be explained by the Kondo collapse and related suppression of both intraband and interband contribution in Kondo melting liquid. This theoretical insight is accessible with time- and angle-resolved photoemission spectroscopy and high-harmonic generation spectroscopy and will stimulate the investigation of nonequilibrium dynamics and nonlinear phenomenon in heavy fermion systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Machine learning assisted prediction of tungsten heavy alloy plasma facing component performance for fusion energy applications

Tungsten and tungsten heavy alloys (WHAs), known for their remarkably high hardness, durability, and corrosion resistance, play a critical role in the thriving development of nuclear fusion reactors in recent years. However, the exploration in tungsten alloys for the nuclear-related applications has been limited by the difficulty of manufacturing and the complexity of experiments to reproduce the environment of nuclear reaction. Therefore, this project aims to utilize nanoscale simulation methods such as density functional theory (DFT) and molecular dynamics (MD) with the help of machine learning techniques to not only understand the mechanisms of tungsten alloys but also allow us to computationally predict their mechanical behaviors under extreme environments. One critical problem of the application of WHAs in nuclear reactors is the surface melting. In the current design of the SPARC reactor, the WHA, W97Ni2.1Fe0.9 or W97NiFe, is chosen to be the first wall components to confine the plasma where the particles are fiercely moving and colliding into each other to create nuclear fusion reaction. This process will generate extremely high heat flux onto these WHA tiles, leaving high surface temperature that could possibly melt the surface of the WHA tiles, As illustrated in Fig. 1(a). a laser experiment previously done illustrates that a rough surface damage would be made after the surface melting where the matrix area mainly composed of nickel and iron as shown in Fig. 1(b), will first melt and then leave vacancies between these tungsten grains. Unfortunately, these kinds of roughness on the first-wall components could be deadly to the plasma inside a Tokmak reactor because the heat that is supposed to dissipate at a designed ratio through the tiles may in turn be excessively absorbed and accumulated on any uneven area of the surface, which will eventually make the whole nuclear reaction fail. In this project, we will introduce a machine learning potential, Allegro, based on DFT calculation and then build a MD model for W-Ni-Fe alloys.

36 MATERIALS SCIENCE↗