Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser directionality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Preheat effects in laser-driven Rayleigh–Taylor instability experiments at intensities greater than $10^{15}$ $\textrm{W}$ $\textrm{cm}^{-2}$ at OMEGA EP and the NIF

The propagation of high-energy X-rays or hot electrons have the potential to alter the initial conditions in experimental target designs, especially at material interfaces, for laser-driven inertial confinement fusion (ICF) and high-energy density (HED) experimental platforms. Hot-electron preheat can drastically modify the initial conditions of experimental targets used to study the deceleration-stage Rayleigh–Taylor instability (RTI) both with and without applied magnetic fields. Therefore, it is necessary to understand and quantify the impact of hot-electron preheat. The hydrodynamic (HD) capabilities in the Ares code are used to study the effects varying levels of preheat can have on RTI evolution. The experimental and computational studies presented in this work demonstrate that at high laser intensities of around or greater than 10 15 W cm −2 , there is hot-electron generation from laser plasma instabilities which induces substantial preheat and impacts the morphology of RTI evolution and even inhibits the intended RTI growth such that it is not observable experimentally. The necessity of better quantifying hot-electron induced preheat and mitigating its impact on such high-intensity direct-drive laser experiments in the future is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Impact of Additive Manufacturing on Internal Cooling Channels With Varying Diameters and Build Directions

Abstract The use of additive manufacturing (AM) processes, such as direct metal laser sintering, provides the design freedom required to incorporate complex cooling schemes in gas turbine components. Additively manufactured turbine components have a range of cooling feature sizes and, because of the inherent three-dimensionality, a wide range of build angles. Previous studies have shown that AM built directions influence internal channel surface roughness that, in turn, augment heat transfer and pressure loss. This study investigates the impact of AM on channel feature size and builds direction relative to tolerance, surface roughness, pressure losses, and convective cooling. Multiple AM coupons were built from Inconel 718 consisting of channels with different diameters and a variety of build directions. An experimental rig was used to measure pressure drop to calculate friction factor and was used to impose a constant surface temperature boundary condition to collect Nusselt number over a range of Reynolds numbers. Significant variations in surface roughness and geometric deviations from the design intent were observed for distinct build directions and channel sizes. These differences led to notable impacts in friction factor and Nusselt number augmentations, which were a strong function of build angle.

Engineering↗
DOE OSTI2026

Redirection and reshaping of intense extreme-ultraviolet radiation

The goal to control short-wavelength radiation for the investigation and manipulation of ultrafast dynamics in quantum systems coevolves with the growing availability of extreme-ultraviolet (XUV) and x-ray sources from high-harmonic generation and free-electron lasers. Here, we present an XUV spatio-spectral phase modulator based on an intense XUV laser beam propagating through an optically thick resonant target, introducing dispersion profile variations around the resonance both perpendicular to and along the laser propagation direction. The resulting dipole radiation gets spectrally reshaped and becomes more divergent as compared to the original beam in the far field. As an experimental demonstration, the intense-XUV–induced double-peak off-axis structure in the far-field spectrum obtained at the Free-Electron Laser in Hamburg (FLASH) shows indications of the underlying XUV-driven Rabi dynamics and resonant pulse propagation effects. The presented work highlights a ubiquitous phenomenon occurring when an intense laser beam passes through a resonant medium.

He, Yu [Max-Planck-Institut für Kernphysik, Heidel↗
DOE OSTI2026

Transversely pumped laser driven particle accelerator

We present a novel acceleration scheme capable of accelerating electrons and ions in an underdense plasma. Transversely Pumped Acceleration (TPA) uses multiple arrays of counter-propagating laser beamlets that focus onto a central acceleration axis. Tuning the injection timing and the spacing between the adjacent beamlets allows for precise control over the position and velocity of the intersection point of the counter-propagating beam arrays. This results in an accelerating structure that propagates orthogonal to the direction of laser propagation. We present the theory that sets the injection timing of the incoming pulses to accelerate electrons and ions with a tunable phase velocity plasma wave. Simulation results are also presented which demonstrate 1.12 GeV proton beams accelerated in 3.6 mm of plasma and electron acceleration gradients on the order of 1 TeV/m in a scheme that circumvents dephasing. This work has potential applications as a compact accelerator for medical physics and high energy physics colliders.

Laser-produced plasmas↗
DOE OSTI2020

Trajectory of a flying plasma mirror traversing a target with density gradient

It has been proposed that laser-induced relativistic plasma mirror can accelerate if the plasma has a properly tailored density profile. Such accelerating plasma mirrors can serve as analog black holes to investigate Hawking evaporation and the associated information loss paradox. Here we reexamine the underlying dynamics of mirror motion in a graded-density plasma to provide an explicit trajectory as a function of the plasma density and its gradient. Specifically, a decreasing plasma density profile (down-ramp) along the direction of laser propagation would in general accelerate the mirror. In particular, a constant-plus-exponential density profile would generate the Davies–Fulling trajectory with a well-defined analog Hawking temperature, which is sensitive to the plasma density gradient but not to the density itself. Furthermore, we show that without invoking nano-fabricated thin-films, a much lower density gas target at, for example, ~1 × 10 17 cm -3 , would be able to induce an analog Hawking temperature, k B T H ~3.1 × 10 -2 eV, in the far-infrared region. We hope that this would help to better realize the experiment proposed by Chen and Mourou.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

In situ synchrotron X-ray imaging and mechanical properties characterization of additively manufactured high-entropy alloy composites

Laser beam directed energy deposition has become an increasingly popular advanced manufacturing technique for materials discovery as a result of the in situ alloying capability. In this study, we leverage an additive manufacturing enabled high throughput materials discovery approach to explore the composition space of a graded W x (CoCrFeMnNi) 100–x sample spanning 0 ≤ x ≤ 21 at%. In addition to microstructural and mechanical characterization, synchrotron high speed x-ray computer aided tomography was conducted on a W 20 (CoCrFeMnNi) 80 composition to visualize melting dynamics, powder-laser interactions, and remelting effects of previously consolidated material. Results reveal the formation of the Fe 7 W 6 intermetallic phase at W concentrations> 6 at%, despite the high configurational entropy. Unincorporated W particles also occurred at W concentrations> 10 at% accompanied by a dissolution band of Fe 7 W 6 at the W/matrix interface and hardness values greater than 400 HV. In this work, the primary strengthening mechanism is attributed to the reinforcement of the Fe 7 W 6 and W phases as a metal matrix composite. The in situ high speed x-ray imaging during remelting showed that an additional laser pass did not promote further mixing of the Fe 7 W 6 or W phases suggesting that, despite the dissolution of the W into the Fe 7 W 6 phase being thermodynamically favored, it is kinetically limited by the thickness/diffusivity of the intermetallic phase, and the rapid solidification of the laser-based process.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hybrid direct drive with a two-sided ultraviolet laser

This paper presents a “hybrid” approach to direct drive inertial confinement fusion that can exploit a high-energy gas laser with two opposed beams. The target and driver are asymmetric, much like experiments performed on the National Ignition Facility, but have been designed to benefit from scale and their particular compatibility with a fusion power plant. The imploded masses (and areal densities) are increased by a factor of 12 (3) and provide a path to high-gain implosions that robustly ignite. The design also mitigates common concerns such as laser imprint and cross-beam energy transfer. We discuss the rationales for a hybrid target, the methods used to control implosion symmetry, and the implication(s) for inertial fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Structural integrity of additively manufactured stainless steel with cold sprayed barrier coating under combined cyclic loading

Integration of metal additive manufacturing (AM) and cold spray (CS) technologies provide an unprecedented opportunity to manufacture coated material systems with complex geometrical features. The application of these material systems in functionally critical components requires adequate structural integrity, particularly in the presence of cyclic loading. This article researches the multiaxial fatigue (axial-torsional cyclic loading) behavior of a coated material system consisting of 15Cr-5Ni precipitation-hardening stainless steel (15-5 PH SS) substrate additively manufactured by direct metal laser sintering with a layer of chromium carbide nickel (CrC-Ni) barrier coating deposited by CS. The influence of AM and CS-induced residual stresses on fatigue performance of test specimens was thoroughly studied. Additionally, the effect of surface roughness and processes induced defects were considered to explain the crack growth mechanism. Stresses assessed by synchrotron X-ray diffraction indicated a substantial accumulation of residual stresses, particularly in the outer surface of the as-fabricated 155 PH SS specimens. The state of residual stress was changed notably following the deposition of CrC-Ni coating in the axial, hoop, and radial directions of the fatigue test specimen. Also, CS deposition of CrC-Ni coating caused significant improvement in the surface quality of the additively manufactured components. Fatigue test results indicated, CS deposition of CrC-Ni substantially enhances the fatigue life of the AM-produced 15-5 PH SS substrate in all loading conditions, particularly in the high cycle fatigue regime. The improvement in the fatigue life of the specimens with coating was associated with a reduction in equivalent residual stress at the substrate surface and improvement in the specimens' surface condition (i.e., reduced surface roughness). The fractographic analysis of the specimen indicated the cracks tend to initiate in the surface of both as-fabricated and cold-sprayed specimens. However, the mechanism of crack growth changed notably following the deposition of CrC-Ni coating. The cracks tended to propagate in the planes parallel or with a small deviation from the build layers of the AM-produced specimens. On the other hand, deposition of CrC-Ni coating increased the deviation of crack growth plane from the build layers of the substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

On the Mechanical Behavior of LP-DED C103 Thin-Wall Structures

Laser Powder Directed Energy Deposition (LP-DED) can produce thin-wall features on the order of 1 mm. These features are essential for large structures operating in extreme environments such as regeneratively cooled nozzles and heat exchangers, which often make use of refractory metals. In this work, the mechanical behavior of LP-DED C103 was investigated via quasi-static tensile testing and low cycle fatigue (LCF) testing. The effects of vacuum stress relief (SR) and hot isostatic pressing (HIP) heat treatments were investigated for specimens in the vertical and horizontal build orientations during tensile testing. The AB and SR properties were lower than literature values for wrought and laser powder bed fusion (L-PBF) bulk components but higher than electron beam powder bed fusion (EB-PBF). The application of a HIP cycle improved strength by 7% and ductility by 27% past the initial as-built condition. Fracture images reveal that interlayer stress concentration sites are responsible for fracture in specimens in the vertical orientation. Meanwhile, fracture in the horizontal specimens mainly propagates at a slanted angle typical of plane stress conditions. The LCF results show cycles to failure ranging from 100 cycles to 8000 cycles for max strain levels of 2% and 0.5%, respectively. Fractography on the fatigue specimens reveals an increasing propagation zone as max strain levels are increased. The impact of these findings and future work are discussed in detail.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Neutron Characterization of 3D Printed Gas Turbine Alloy With Internal Cooling Structure

The objective of this research work is to investigate the residual strains induced by the presence of a exit hole and internal hollow geometry present in a 3D printed IN718 similar to that seen in a gas turbine blade. The specimens were manufactured with an internal hollow structure that ended with an exit hole, and fabricated by direct metal laser sintering additive manufacturing technique. Using this technique, metal powder was melted by a laser source and rapidly cooled to form the part layer by layer. Rapid heating and cooling generate large thermal gradients and residual stresses in the 3D printed material. To be aligned with industry standards, specimens were heat-treated to relieve most of the residual stresses as well as to investigate whether IN718 still preserved a nonhomogeneous stress state after the thermal treatment. Roughness and microstructure analysis was performed to understand the heat-treated sample properties. To investigate the volumetric residual strain, the neutron diffraction technique was used with a definite neutron wavelength. Bragg’s law was used to determine lattice spacing. Interplanar lattice spacing and stress-free state lattice spacings were measured to calculate the strains. Residual strains were measured in the x and y direction to understand the impact of the presence of a exit hole and internal hollow geometry. The results of volumetric residual strain in the x and y directions showed no significant variations in the distribution of the strain due to the presence of a hollow structure as well as the exit hole. Overall, no significant stress concentration was observed in the heat treated sample. Sample geometry, instrumentation for neutron diffraction, and material properties are discussed in detail in this paper.

Raju, Nandhini↗
DOE OSTI2020

Engineering Directionality in Quantum Dot Shell Lasing Using Plasmonic Lattices

In this paper, we report how the direction of quantum dot (QD) lasing can be engineered by exploiting high-symmetry points in plasmonic nanoparticle (NP) lattices. The nanolaser architecture consists of CdSe-CdS core-shell QD layers conformally coated on two-dimensional square arrays of Ag NPs. Using waveguide-surface lattice resonances (W-SLRs) near the Δ point in the Brillouin zone as optical feedback, we achieved lasing from the gain in CdS shells at off-normal emission angles. Changing the periodicity of the plasmonic lattices enables other high-symmetry points (Γ or M) of the lattice to overlap with the QD shell emission, which facilitates tuning of the lasing direction. We also increased the thickness of the QD layer to introduce higher order W-SLR modes with additional avoided crossings in the band structure, which expands the selection of cavity modes for any desired lasing emission angle.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Evaluation of DED and LPBF Fe-based Alloys Process Application Envelopes based on Performance, Process Economics, Supply Chain Risks, and Reactor-specific Targeted Components

The U.S. Department of Energy (DOE), Office of Nuclear Energy (NE), Advanced Materials and Manufacturing Technologies (AMMT) program aims to develop extreme-environment materials solutions for use in the deployment of advanced nuclear reactors and the sustainment of the current fleet. To achieve this objective, a combination of experiment, a computational tool, and machine learning (ML) for the design of materials is adopted for the maturation of materials for nuclear technology. Through advanced manufacturing techniques such as laser powder bed fusion (LPBF) and laser powder direct energy deposition (LP-DED), components with complex geometries can be fabricated with reduced time and effort. Such advanced manufacturing methods can also provide the opportunity to improve materials performance through optimized microstructures and mechanical properties. However, existing engineering alloys are not always well suited for fabrication with additive manufacturing (AM), as their compositions have been tuned to optimize fabrication via conventional methods. Thus, similar alloys with modified compositions that are better suited for AM can be studied for improved performance. Over the past three years, the AMMT teams from Argonne National Laboratory (ANL) and Pacific Northwest National Laboratory (PNNL) studied various known Fe-based alloys by evaluating their initial printability using LPBF, and an AMMT-developed down-selection and decision matrix reduced the number of alloys to be studied from six to three in fiscal year (FY) 2024. Additionally, in FY 2024, for parallel evaluation, these three alloys were studied using LPDED. While LPBF is better for small- to medium-sized components with high detail and internal features, LP-DED combines a material feed system to place the powder onto the exact spot where the laser will melt the material. This AM method can be easily scaled to extremely large components and provides high build rate speeds compared to those of conventional LPBF systems. Additionally, DED is a better choice for complex geometries and compositional gradients.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Experimental Evaluation and Fluid–Structure Model Predictions

This paper presents rotating test results and advances an analytical predictive fluid–structure model for a new type of gas-lubricated thrust bearing fabricated using direct metal laser melting. The bearing concept in this study is a compliant hybrid gas thrust bearing that uses external pressurization to increase load carrying capacity, where the testing campaign in this study was only focused on steady-state static performance. The need for the bearing concept comes from enabling highly efficient supercritical carbon dioxide (sCO2) turbomachinery by replacing oil-lubricated bearings with process gas lubrication. Leveraging the process gas of the turbomachine for bearing lubrication results in lowered bearing power loss, simplified mechanical design, and allows for novel oil-free hermetic drivetrains resulting in an efficient emission-free system. The new concept utilizes hydrostatic pressurization on individual tilting pads flexibly mounted with hermetic squeeze film dampers (HSFDs). This paper focuses on rotating tests of a 173 mm outer diameter gas thrust bearing in air up to 10 krpm and hydrostatic inlet pressures to 365 psi (2.52 MPa). The influence of thrust runner speed and bearing inlet pressure on force deflection characteristics and load carrying capability of the gas film were experimentally evaluated. This work also advances a predictive fluid–structure thrust bearing model using an isothermal ideal-gas-based compressible Reynolds flow equation directly coupled to a lumped stiffness element possessing axial and rotational degrees-of-freedom. The rotating testing demonstrated load capability of 1816 lbs (8.1 kN), which equates to a thrust bearing unit load of 67 psi (0.46 MPa). Gas film force–deflection curves reveal a nonlinear relationship between thrust load and film clearance. Comparison of film thickness values with the predictive model show good agreement under high load and inlet pressure, however deviate as load and pressure decrease. Load capability was shown to increase with increasing hydrostatic inlet pressure, while the increase in thrust runner speed revealed a small decrease in load capacity.

Engineering↗
DOE OSTI2021

Convection in Scaled Turbine Internal Cooling Passages With Additive Manufacturing Roughness

Abstract Additive manufacturing processes, such as direct metal laser sintering (DMLS), enable the creation of novel turbine cooling internal passages and systems. However, the DMLS method produces a significant and unique surface roughness. Previous work in scaled passages analyzed pressure losses and friction factors associated with the rough surfaces, as well as investigated the velocity profiles and turbulent flow characteristics within the passage. In this study, the heat transfer characteristics of scaled additively manufactured surfaces were measured using infrared (IR) thermography. Roughness panels were CNC machined from plates of aluminum 6061 to create near isothermal roughness elements when heated. Fluid resistance differences between the aluminum roughness panels and roughness panels constructed from ABS plastic using the same roughness patterns from McClain et al. (2020, “Flow in a Simulated Turbine Blade Cooling Channel With Spatially Varying Roughness Caused by Additive Manufacturing Orientation,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-16069) were investigated. Finally, the overall thermal performance enhancements and friction losses were assessed through the calculation of surface averaged “global thermal performance” ratios. The global thermal performance characterizations indicate results in-line with those found for traditional commercial roughness and slightly below traditional internal passage convection enhancement methods such as swirl chambers, dimples, and ribs. The passages investigated in this study do not include compressibility effects or the long-wavelength artifacts and channel geometric deviations observed by Wildgoose et al. (2020, “Impact of Additive Manufacturing on Internal Cooling Channels with Varying Diameters and Build Directions,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-15049). However, the results of this study indicate that, based on the roughness augmentation alone, artificial convective cooling enhancers such as turbulators or dimples may still be required for additively manufactured turbine component cooling.

Engineering↗
DOE OSTI2020

Automated detection of part quality during two-photon lithography via deep learning

Two-photon lithography (TPL) is an additive manufacturing technique for fabricating three-dimensional objects with nanoscale features. A main challenge of TPL is the routine and labor-intensive task of finding suitable light dosage parameters, i.e. writing speed and laser intensity that induce photo-polymerization within a wide variety of candidate photo-curing polymers. Another challenge is the monitoring required during fabrication. In this work, we apply machine learning (ML) models to accelerate the process of identifying optimal light dosage parameters and automate the detection of part quality. We curate TPL videos of different parts fabricated under a range of light dosage parameters using different resins and train spatial-temporal ML models on this data. Our results show that ML models can detect TPL part quality with a 95.1% accuracy in milliseconds. We also evaluate classification failures and identify two operating modes: parameter optimization and part quality detection. Last but not least, we publicly release this labelled dataset so that it may serve as a useful benchmark to the community. Our approach to process optimization and part quality detection addresses important aspects of TPL industrialization, is applicable beyond TPL and should benefit other additive manufacturing techniques with similar barriers to operating at industrial scale.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Recent Advances in Scalable, High‐Mass Loaded Electrodes for Grid‐Scale Energy Storage

Abstract The increasing electrification of daily life as well as the intermittent characteristic of renewable energy sources require viable solutions for grid‐scale energy storage. Critical considerations for grid storage applications are electrode mass loading and electrode thickness as these features govern battery pack energy density, an important factor in determining manufacturing costs. For this reason, there is increased interest in finding new ways of creating electrodes with high mass loading. In this review, various high‐mass loading fabrication approaches are considered for positive electrode materials used in batteries. The benchmark used for high mass loading is above 20 mg cm −2 , which is higher than the practical limit of conventional tape‐cast electrodes. Several different electrode approaches are described including templating, laser patterning, direct ink writing, and electrodeposition. A variety of materials are covered with the most prominent being LiFe(PO 4 ) (LFP), LiCoO 2 (LCO), and MnO 2 . In research to date, scalable electrochemical performance has been achieved with mass loadings over 100 mg cm −2 . Areal capacities as high as 14.7 mAh cm −2 at 1.82 mA cm −2 have been achieved in non‐aqueous electrolytes and 9.8 mAh cm −2 at 10 mA cm −2 in aqueous electrolytes. These results establish that the mass loading of electrodes can be scaled up without compromising their electrochemical properties.

White, Makena [Department of Materials Science and↗
DOE OSTI2021

Observation of Quadratic (Charge-2) Weyl Point Splitting in Near-Infrared Photonic Crystals

Weyl points are point degeneracies that occur in momentum space of 3D periodic materials and are associated with a quantized topological charge. Here, the splitting of a quadratic (charge-2) Weyl point into two linear (charge-1) Weyl points in a 3D micro-printed photonic crystal is observed experimentally via Fourier-transform infrared spectroscopy. Using a theoretical analysis rooted in symmetry arguments, it is shown that this splitting occurs along high-symmetry directions in the Brillouin zone. This micro-scale observation and control of Weyl points is important for realizing robust topological devices in the near-infrared.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Crystal plasticity model of residual stress in additive manufacturing using the element elimination and reactivation method

Selective laser melting is receiving increasing interest as an additive manufacturing technique. Residual stresses induced by the large temperature gradients and inhomogeneous cooling process can favour the generation of cracks. In this work, a crystal plasticity finite element model is developed to simulate the formation of residual stresses and to understand the correlation between plastic deformation, grain orientation and residual stresses in the additive manufacturing process. The temperature profile and grain structure from thermal-fluid flow and grain growth simulations are implemented into the crystal plasticity model. An element elimination and reactivation method is proposed to model the melting and solidification and to reinitialize state variables, such as the plastic deformation, in the reactivated elements. The accuracy of this method is judged against previous method based on the stiffness degradation of liquid regions by comparing the plastic deformation as a function of time induced by thermal stresses. The method is used to investigate residual stresses parallel and perpendicular to the laser scan direction, and the correlation with the maximum Schmid factor of the grains along those directions. The magnitude of the residual stress can be predicted as a function of the depth, grain orientation and position with respect to the molten pool. The simulation results are directly comparable to X-ray diffraction experiments and stress–strain curves.

316 stainless steel↗