Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hot wire”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Accuracy and directional sensitivity of the single-wire technique

Multi-orientation of a single-hot-wire is a novel way to measure the three time-mean velocities, the three turbulent normal stresses, and the three turbulent shear stresses. The present study focuses on the accuracy and directional sensitivity of the technique with respect to mean flow velocity orientation to the probe. Results demonstrate relative insensitivity, indicating that the method is a useful cost-effective tool for turbulent flows of unknown dominant flow direction.

Lilley, D. G.↗
NASA NTRS1982

An experimental search for near-wall boundary conditions for large eddy simulation

Instantaneous wall shear stress and streamwise velocities have been measured simultaneously in a flat plate, turbulent boundary layer at moderate Reynolds number in an effort to provide experimental support for large eddy simulations. Data were obtained by using a buried-wire wall shear gage and a hot-wire rake positioned in the log region of the flow. All data processing was accomplished with digital data analysis techniques on a minicomputer. Fluctuations of the instantaneous U plus versus Y plus profiles about a mean law of the wall are shown to be significant and complex. Peak cross-correlation values between wall shear stress and the velocities are high and reflect the passage of a large structure inclined at a small angle to the wall. Estimates of this angle are consistent with those made by other investigators. Conditional sampling techniques were used to detect the passage of various sizes and types of flow disturbances (events) and to estimate their mean frequency of occurrence. Events characterized by large and sudden streamwise accelerations were found to be highly coherent throughout the log region and were strongly correlated with large fluctuations in wall shear-stress. Phase randomness between the near-wall quantities and the outer velocities was small. The results suggest that the flow events detected by conditional sampling applied to velocities in the log region may be related to the bursting process.

Robinson, S. K.↗
NASA NTRS1986

Instantaneous velocity profile measurements in a turbulent boundary layer

Instantaneous wall shear stress and streamwise velocities have been measured simultaneously in a flat-plate, turbulent boundary layer at moderate Reynolds number in an effort to provide experimental support for large eddy simulations. Data were obtained using a buried-wire, wall shear gage and a hot-wire rake positioned in the log region of the flow. Fluctuations of the instantaneous U(+) versus Y(+) profiles about a mean law of the wall are shown to be significant and complex. Peak cross-correlation values between wall shear stress and the velocities are high, and reflect the passage of a large structure inclined at a small angle to the wall. Estimates of this angle are consistent with those made by other investigators. Conditional sampling techniques were used to detect the passage of various sizes and types of flow disturbances (events), and to estimate their mean frequency of occurrence. Events characterized by large aand sudden streamwise accelerations were found to be highly coherent throughout the log region and were strongly correlated with large fluctuations in wall shear stress. Phase randomness between the near-wall quantities and the outer velocities was small. The results suggest that the flow events detected by conditional sampling applied to velocities in the log region may be related to the bursting process.

Robinson, S. K.↗
NASA NTRS1924

A Method for the Instantaneous Determination of the Velocity and Direction of the Wind

The laboratory instruments, which we often constructed with makeshift means, gave encouraging results and showed that they could satisfactorily meet the required conditions. By limiting ourselves to the employment of hot wires of 0.05 mm (0.002 in.) diameter, we obtained instruments which faithfully followed all the wind fluctuations of over 0.1 second and even much more rapid variations without any very great error.

INSTRUMENTS - ANEMOMETERS↗
NASA NTRS1942

An Experimental Investigation of Flow Across Tube Banks

Flow across tube banks was investigated by surveys of total dynamic and static pressure by visualization of the flow through the use of titanium tetrachloride smoke, by thermocouple surveys of heated tubes, and by hot-wire surveys of both heated and unheated tubes. It was found that turbulence increased as the depth of the bank increased and that the broad wake behind each tube affected flow over the succeeding tubes.

AIR FLOW, TURBULENT-MEASUREMENT, HOT-WIRE↗
NASA NTRS2024

Background Turbulence Characterization of the Curved Duct Test Rig

Interest in applying acoustic treatment to nontraditional locations of turbofan engines has led to recent testing of acoustically treated airfoils in the NASA Langley Curved Duct Test Rig. Current testing focuses only on sound attenuation by the sample when exposed to an incident sound field driven by a loudspeaker array. However, there may be much to gain from an aeroacoustic study of the interaction of turbulence with treated airfoils, especially in the case of acoustically treated outlet guide vane designs. Thus, the intent of this study is to take the first step in assessing the aeroacoustic quality of the NASA Langley Curved Duct Test Rig (typically only used for grazing flow studies) by examining the flow quality. The background turbulence levels are measured using hot-wire anemometry just upstream of the test section. Measurements indicate that the turbulence intensity is less than 0.3% in the core region of the flow. The autospectral densities show cavity tones and weak vortex shedding present in the core. The vortex shedding is determined to be from the upstream total pressure probe used to determine flow speed. The cavity tones are found to be the fundamental and harmonic frequencies of a porous ceramic tubular acoustic liner sample that separates the acoustic drivers from the flow region. Recommendations for improving the aeroacoustic quality of the tunnel are provided, such as removing the upstream probe and redesigning the ceramic tubular liner. Future acoustic characterization of the background levels is also recommended to further understand the feasibility of aeroacoustic studies in CDTR.

Wind Tunnel Characterization↗
NASA NTRS1998

Experimental Study of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. Freestream turbulence levels ranging from 0.8% to 3% was used in this experiment. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. Hot-wires (single and x-wire) and surface mounted hot-film gases and static pressure taps were used to map the flowfield. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗
NASA NTRS1992

Hot wire/film behavior in low-temperature gases

Commercially available hot wires/films were used to measure the velocities of evaporated hydrogen or helium gas during cryogenic mixing experiments. Hot wires were found to be too delicate to use in this harsh environment. Hot films were rugged enough to use at cryogenic temperatures even though they failed after a number of thermal cycles. Since the hot films have small aspect ratios, 13.4 and 20, they are quite sensitive to the thermal loading, Tw/Tg, even with a correction for the conduction end loss. In general, although the increase of the Nusselt number with Reynolds number at low temperatures was similar to that at room temperature, there was also a pronounced variation with Tw/Tg over the large range of 1.2 to 12 investigated.

Kwack, E. Y.↗
NASA NTRS1986

A summary of Reynolds number effects on some recent tests in the Langley 0.3-meter transonic cryogenic tunnel

Reynolds number effects noted from selected test programs conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT) are discussed. The tests, which cover a unit Reynolds number range from about 2.0 to 80.0 million per foot, summarize effects of Reynolds number on: (1) aerodynamic data from a supercritical airfoil, (2) results from several wall interference correction techniques, and (3) results obtained from advanced, cryogenic tests techniques. The test techniques include: (1) use of a cryogenic sidewall boundary layer removal system, (2) detailed pressure and hot wire measurements to determine test section flow quality, and (3) use of a new hot film system suitable for transition detection in a cryogenic wind tunnel. The results indicate that Reynolds number effects appear most significant when boundary layer transition effects are present and at high lift conditions when boundary layer separation exists on both the model and the tunnel sidewall.

Johnson, C. B.↗
NASA NTRS2008

Microstructural Evaluation and Comparison of Solder Samples Processed Aboard the International Space Station

Samples from the In-Space Soldering Investigation (ISSI), conducted aboard the International Space Station (ISS), are being examined for post-solidification microstructural development and porosity distribution. In this preliminary study, the internal structures of two ISSI processed samples are compared. In one case 10cm of rosin-core solder was wrapped around a coupon wire and melted by conduction, whereas, in the other a comparable length of solder was melted directly onto the hot wire; in both cases the molten solder formed ellipsoidal blobs, a shape that was maintained during subsequent solidification. In the former case, there is clear evidence of porosity throughout the sample, and an accumulation of larger pores near the hot end that implies thermocapillary induced migration and eventual coalescence of the flux vapor bubbles. In the second context, when solder was fed onto the wire. a part of the flux constituting the solder core is introduced into and remains within the liquid solder ball, becoming entombed upon solidification. In both cases the consequential porosity, particularly at a solder/contact interface, is very undesirable. In addition to compromising the desired electrical and thermal conductivity, it promotes mechanical failure.

Grugel, R. N.↗
NASA NTRS1999

Effect of Wall Temperature on Roughness Induced Attachment-Line Transition

An experiment on a cooled swept cylinder in a low-disturbance Mach 1.6 wind tunnel is described. The flow attachment line is disturbed by trip wires of varying size and the laminar/turbulent state of the downstream boundary layer is determined with a hot wire. The results demonstrate that although cooling the wall increases the stability of the boundary layer, it promotes roughness induced transition. Analysis of the data suggests that the attachment- line Reynolds number can account for the effect of wall cooling if the viscosity is evaluated at a particular reference temperature.

Dietz, Anthony↗
NASA NTRS1983

Turbulence Characteristics of Swirling Flowfields

Combustor design phenomena; recirculating flows research; single-wire, six-orientation, eddy dissipation rate, and turbulence modeling measurement; directional sensitivity (DS); calibration equipment, confined jet facility, and hot-wire instrumentation; effects of swirl, strong contraction nozzle, and expansion ratio; and turbulence parameters; uncertain; and DS in laminar jets; turbulent nonswirling jets, and turbulent swirling jets are discussed.

Jackson, T. W.↗
NASA NTRS1991

Applications of hot-film anemometers in hypersonic shear layers

A wind tunnel test was conducted on a flat plate at zero angle of attack with a rearward facing 2D cooling film injector nozzle. The freestream Mach number was 8 and the injector Mach number was 3. The freestream Reynolds number varied from 0.43 to 3.3 million per ft during the test, and the injector flow rate was such that the jet exit and freestream static pressures were matched. The analysis reported herein will focus on data obtained at a freestream Reynolds number of 0.85 million per ft. The data consists of heat-transfer measurements obtained upstream and downstream of the injector nozzle and flowfield surveys obtained downstream of the injector nozzle with a pitot, total temperature, hot-film anemometer and hot-wire anemometer probes. The flowfield surveys were made at stations 0.1 to 9 in. downstream of the injector nozzle from near the model surface to approximately 2 in above the model surface. The hot-film anemometer was used to define the fluctuations in the shear layer separating the flows. The hot-film results are integrated with conventional measurement techniques to obtain a more complete description of the complicated shear layer separating hypersonic and supersonic flows.

Grubb, J. P.↗
NASA NTRS1980

Experimental investigation of a three dimensional turbulent boundary layer with a non disappearing pressure gradient

The results of measuring profiles of temporally determined velocities and Reynolds tension, wall shear stresses and pressure distribution in a three dimensional, turbulent boundary layer with pressure gradients in both tangential directions are reported. For determining the velocities X wire probes were used whose cooling was gauged according to magnitude and direction of the flow and was described with an effective cooling speed. In the evaluation consideration is given to the directional sensitivity of the hot wire. The ratio of the turbulence viscosities is calculated for both tangential directions and is found to be approximately N equals 1.2. Further, the profiles of the mixing path lengths for the flow direction are found to vary only slightly with increasing X-coordinates, while the boundary layer thickness increases substantially. The relationships of turbulent shear stress to turbulent, kinetic fluctuation energy is approximately constant over a large part of the boundary layer.

Mueller, U.↗
NASA NTRS1986

Resistance heating of Fe and W in diamond-anvil cells

A new method for internally heating a diamond-anvil cell is described. Fine wires of iron or tungsten are resistively heated in a gasketed cell, thus providing a uniformly distributed pressure that can be measured in situ by employing the ruby scale. Temperatures of several thousand degrees have been measured by fitting a black body radiation function to the spectrum of the hot wire taken with an optical multichannel analyzer. Temperatures as high as the melting temperature of tungsten have been achieved. The alpha-gamma and alpha-epsilon phase transitions of iron have been studied, and the results show excellent agreement with previous data obtained with piston-cylinder or externally-heated diamond cells.

Boehler, R.↗