SEARCH · Engineering Papers

Results for “higher form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Synoptic maps of heliospheric Thomson scattering brightness from 1974-1985 as observed by the Helios photometers

We display the electron Thomson scattering intensity of the inner heliosphere as observed by the zodiacal light photometers on board the Helios spacecraft in the form of synoptic maps. The technique extrapolates the brightness information from each photometer sector near the Sun and constructs a latitude/longitude map at a given solar height. These data are unique in that they give a determination of heliospheric structures out of the ecliptic above the primary region of solar wind acceleration. The spatial extent of bright, co-rotating heliospheric structures is readily observed in the data north and south of the ecliptic plane where the Helios photometer coverage is most complete. Because the technique has been used on the complete Helios data set from 1974 to 1985, we observe the change in our synoptic maps with solar cycle. Bright structures are concentrated near the heliospheric equator at solar minimum, while at solar maximum bright structures are found at far higher heliographic latitudes. A comparison of these maps with other forms of synoptic data are shown for two available intervals.

Hick, P.↗

NASA NTRS1978

An experimental investigation of the condensation of silicate grains

Results are presented for a series of laboratory experiments designed to investigate the nucleation of small silicate grains from a vapor of astrophysically significant elements and compounds. In the experiments, magnesium silicate grains were condensed by simultaneously evaporating Mg and SiO solids into an atmosphere of argon or hydrogen at a pressure of a few torr. The results show that at low temperatures (up to a few hundred degrees C) the condensates are amorphous grains and have widely varying stoichiometries. The thermodynamically most stable compounds (Mg2SiO4, MgSiO3, SiO2) do not form readily, but all initial condensates can be converted to crystalline forsterite (Mg2SiO4) by heating to 1000 C in vacuum. At higher temperatures (above 700 K) it becomes more difficult to nucleate any silicates, and those that do form are amorphous, indicating that surface energies and kinetic effects are very important in determining under what conditions condensation will occur. The IR spectra of the experimentally produced magnesium silicates are found to have a strong resemblance to those observed in many astronomical clouds.

Day, K. L.↗

NASA NTRS1982

On higher eigenstates of Goertler instability in compressible flow

The effect of secondary instabilities of Goertler vortices with respect to their growth and amplification was investigated. Instability of viscous flow along a concave surface is in the form of counterrotating streamwise vortices commonly known as Goertler vortices. The effects of suction on higher modes of Goertler vortices are also considered.

Goglia, G. L.↗

NASA NTRS2013

NASA Marshall Space Flight Center Tri-gas Thruster Performance Characterization

Historically, spacecraft reaction control systems have primarily utilized cold gas thrusters because of their inherent simplicity and reliability. However, cold gas thrusters typically have a low specific impulse. It has been determined that a higher specific impulse can be achieved by passing a monopropellant fluid mixture through a catalyst bed prior to expulsion through the thruster nozzle. This research analyzes the potential efficiency improvements from using tri-gas, a mixture of hydrogen, oxygen, and an inert gas, which in this case is helium. Passing tri-gas through a catalyst causes the hydrogen and oxygen to react and form water vapor, ultimately heating the exiting fluid and generating a higher specific impulse. The goal of this project was to optimize the thruster performance by characterizing the effects of varying several system components including catalyst types, catalyst lengths, and initial catalyst temperatures.

Dorado, Vanessa↗

NASA NTRS1976

Zonal and tesseral harmonic coefficients for the geopotential function, from zero to 18th order

Zonal and tesseral harmonic coefficients for the geopotential function are usually tabulated in normalized form to provide immediate information as to the relative significance of the coefficients in the gravity model. The normalized form of the geopotential coefficients cannot be used for computational purposes unless the gravity model has been modified to receive them. This modification is usually not done because the absolute or unnormalized form of the coefficients can be obtained from the simple mathematical relationship that relates the two forms. This computation can be quite tedious for hand calculation, especially for the higher order terms, and can be costly in terms of storage and execution time for machine computation. In this report, zonal and tesseral harmonic coefficients for the geopotential function are tabulated in absolute or unnormalized form. The report is designed to be used as a ready reference for both hand and machine calculation to save the user time and effort.

Kirkpatrick, J. C.↗

NASA NTRS2006

Formation of Metal and Silicate Globules in Gujba: A New Bencubbin-like Meteorite Fall

Gujba is a coarse-grained meteorite fall composed of 41 vol% large kamacite globules, 20 vol% large light-colored silicate globules with cryptocrystalline, barred pyroxene and barred olivine textures, 39 vol% dark-colored, silicate-rich matrix, and rare refractory inclusions. Gujba resembles Bencubbin and Weatherford in texture, oxygen-isotopic composition and in having high bulk delta N-15 values (approximately +685%0). The He-3 cosmic-ray exposure age of Gujba (26 +/- 7 Ma) is essentially identical to that of Bencubbin, suggesting that they were both reduced to meter-size fragments in the same parent-body collision. The Gujba metal globules exhibit metal-troilite quench textures and vary in their abundances of troilite and volatile siderophile elements. We suggest that the metal globules formed as liquid droplets either via condensation in an impact-generated vapor plume or by evaporation of preexisting metal particles in a plume. The lower the abundance of volatile elements in the metal globules, the higher the globule quench temperature. We infer that the large silicate globules also formed from completely molten droplets; their low volatile-element abundances indicate that they also formed at high temperatures, probably by processes analogous to those that formed the metal globules. The coarse-grained Bencubbin-Weatherford-Gujba meteorites may represent a depositional component from the vapor cloud enriched in coarse and dense particles. A second class of Bencubbin-like meteorites (represented by Hammadah a1 Hamra 237 and QUE 94411) may be a finer fraction derived from the same vapor cloud

Rubin, Alan E.↗

NASA NTRS1987

Mixed Cu-simple metal dimers and trimers - CuLi, CuLi2, CuNa, CuK, CuBe, CuBe2, Cu2Be, CuAl, and CuAl2

Theoretical studies of selected diatomic and triatomic molecules containing copper and the simple metals Li, Na, K, Be, and Al are presented, with emphasis on elucidating the nature of the bonding in mixed transition metal-simple metal systems. Large Gaussian basis sets are used in the diatomic calculations, and are used to calibrate the triatomic calculations, in which somewhat smaller Gaussian basis sets are employed. Electron correlation is incorporated using both the single-reference singles plus doubles configuration interaction and coupled pair functional methods. It is found that alkali atoms form very polar sigma bonds with copper, and that the ionicity increases with the inclusion of higher excitations because they improve the electron affinity of copper, which in turn allows a larger negative charge on copper. Aluminum is found to form stronger bonds than beryllium, since it does not have to undergo sp hybridization. Some of the trimers bond by forming three-center three-electron bonds. These multicenter bonds are quite strong even when compared to the two-electron bonds in the dimers or to other bonding mechanisms in the trimers.

Bauschlicher, Charles W., Jr.↗

NASA NTRS1999

Bubble Generation in a Flowing Liquid Medium and Resulting Two-Phase Flow in Microgravity

The present investigation reports a study of bubble generation under reduced gravity conditions, using both a co-flow and a cross-flow configuration. This study may be used in the conceptual design of a space-based thermal management system. Ensuing two-phase flow void fraction can be accurately monitored using a single nozzle gas injection system within a continuous liquid flow conduit, as utilized in the present investigation. Accurate monitoring of void fraction leads to precise control of heat and mass transfer coefficients related to a thermal management system; hence providing an efficient and highly effective means of removing heat aboard spacecraft or space stations. Our experiments are performed in parabolic flight aboard the modified DC-9 Reduced Gravity Research Aircraft at NASA Lewis Research Center, using an air-water system. For the purpose of bubble dispersion in a flowing liquid, we use both a co-flow and a cross-flow configuration. In the co-flow geometry, air is introduced through a nozzle in the same direction with the liquid flow. On the other hand, in the cross-flow configuration, air is injected perpendicular to the direction of water flow, via a nozzle protruding inside the two-phase flow conduit. Three different flow conduit (pipe) diameters are used, namely, 1.27 cm, 1.9 cm and 2.54 cm. Two different ratios of nozzle to pipe diameter (D(sub N))sup * are considered, namely (D(sub N))sup * = 0.1 and 0.2, while superficial liquid velocities are varied from 8 to 70 cm/s depending on flow conduit diameter. It is experimentally observed that by holding all other flow conditions and geometry constant, generated bubbles decrease in size with increase in superficial liquid velocity. Detached bubble diameter is shown to increase with air injection nozzle diameter. Likewise, generated bubbles grow in size with increasing pipe diameter. Along the same lines, it is shown that bubble frequency of formation increases and hence the time to detachment of a forming bubble decreases, as the superficial liquid velocity is in-creased. Furthermore, it is shown that the void fraction of the resulting two-phase flow increases with volumetric gas flow rate Q(sub d), pipe diameter and gas injection nozzle diameter, while they decrease with surrounding liquid flow. The important role played by flowing liquid in detaching bubbles in a reduced gravity environment is thus emphasized. We observe that the void fraction can be accurately controlled by using single nozzle gas injection, rather than by employing multiple port injection, since the later system gives rise to unpredictable coalescence of adjacent bubbles. It is of interest to note that empirical bubble size and corresponding void fraction are somewhat smaller for the co-flow geometry than the cross-flow configuration at similar flow conditions with similar pipe and nozzle diameters. In order to supplement the empirical data, a theoretical model is employed to study single bubble generation in the dynamic (Q(sub d) = 1 - 1000 cu cm/s) and bubbly flow regime within the framework of the co-flow configuration. This theoretical model is based on an overall force balance acting on the bubble during the two stages of generation, namely the expansion and the detachment stage. Two sets of forces, one aiding and the other inhibiting bubble detachment are identified. Under conditions of reduced gravity, gas momentum flux enhances, while the surface tension force at the air injection nozzle tip inhibits bubble detachment. In parallel, liquid drag and inertia can act as both attaching and detaching forces, depending on the relative velocity of the bubble with respect to the surrounding liquid. Predictions of the theoretical model compare well with our experimental results. However, at higher superficial liquid velocities, as the bubble loses its spherical form, empirical bubble size no longer matches the theoretical predictions. In summary, we have developed a combined experimental and theoretical work, which describes the complex process of bubble generation and resulting two-phase flow in a microgravity environment. Results of the present study can be used in a wide range of space-based applications, such as thermal energy and power generation, propulsion, cryogenic storage and long duration life support systems, necessary for programs such as NASA's Human Exploration for the Development of Space (HEDS).

Pais, S. C.↗

NASA NTRS1988

Hydrodynamic effects on cell growth in agitated microcarrier bioreactors

The net growth rate of bovine embryonic kidney cells in microcarrier bioreactor is the result of a variable death rate imposed on a cell culture trying to grow at a constant intrinsic growth rate. The death rate is a function of the agitation conditions in the system, and increases at higher agitation because of increasingly energetic interactions of the cell covered microcarriers with turbulent eddies in the fluid. At very low agitation rates bead-bead bridging becomes important; the large clumps formed by bridging can interact with larger eddies than single beads, leading to a higher death rate at low agitation. The growth and death rate were correlated with a dimensionless eddy number which compares eddy forces to the buoyant force on the bead.

Cherry, Robert S.↗

NASA NTRS1992

Superplastic forming of ceramic insulation

Superplasticity has been demonstrated in many fine-grained structural ceramics and ceramic composites, including yttria-stabilized tetragonal zirconia polycrystal (YTZP), alumina, and Al2O3-reinforced zirconia (Al2O3/YTZ) duplex composites and SiC-reinforced Si3N4. These superplastic ceramics obviously offer the potential benefit of forming net shape or near net shape parts. This could be particularly useful for forming complicated shapes that are difficult to achieve using conventional forming techniques, or require elaborate, subsequent machining. In the present study, we successfully demonstrated the following: (1) superplastic 3Y-TXP and 20 percent Al2O3/YTZ composite have for the first time been successfully deformed into hemispherical caps via a biaxial gas-pressure forming technique; (2) no experimental difficulty was encountered in applying the required gas pressures and temperatures to achieve the results, thus, it is certain that higher rates of deformation than those presented in this study will be possible by using the current test apparatus at higher temperatures and pressures; and (3) an analytical model incorporating material parameters, such as variations during forming in the strain rate sensitivity exponent and grain growth-induced strain hardening, is needed to model accurately and therefore precisely control the biaxial gas-pressure forming of superplastic ceramics. Based on the results of this study, we propose to fabricate zirconia insulation tubes by superplastic extrusion of zirconia polycrystal. This would not only reduce the cost, but also improve the reliability of the tube products.

Nieh, T. G.↗

NASA NTRS1980

A symmetric modal formulation of fluid-structure interaction, including a static approximation to higher order fluid modes

A method of fluid-structure coupling which provides symmetrical matrix equations of standard form solved by existing finite element computer programs is presented. The method postulates that the uncoupled vibration modes of the fluid or the structure be calculated before the coupled analysis. A numerical solution of vibration modes in an axisymmetric container demonstrated that a static approximation to higher order fluid modes can improve the accuracy of dynamic response computations using modal methods.

Macneal, R. H.↗

NASA NTRS1991

Fourier functional analysis for unsteady aerodynamic modeling

A method based on Fourier analysis is developed to analyze the force and moment data obtained in large amplitude forced oscillation tests at high angles of attack. The aerodynamic models for normal force, lift, drag, and pitching moment coefficients are built up from a set of aerodynamic responses to harmonic motions at different frequencies. Based on the aerodynamic models of harmonic data, the indicial responses are formed. The final expressions for the models involve time integrals of the indicial type advocated by Tobak and Schiff. Results from linear two- and three-dimensional unsteady aerodynamic theories as well as test data for a 70-degree delta wing are used to verify the models. It is shown that the present modeling method is accurate in producing the aerodynamic responses to harmonic motions and the ramp type motions. The model also produces correct trend for a 70-degree delta wing in harmonic motion with different mean angles-of-attack. However, the current model cannot be used to extrapolate data to higher angles-of-attack than that of the harmonic motions which form the aerodynamic model. For linear ramp motions, a special method is used to calculate the corresponding frequency and phase angle at a given time. The calculated results from modeling show a higher lift peak for linear ramp motion than for harmonic ramp motion. The current model also shows reasonably good results for the lift responses at different angles of attack.

Lan, C. Edward↗

NASA NTRS1991

Fourier functional analysis for unsteady aerodynamic modeling

Chin, Suei↗

NASA NTRS1962

The Effect of Initial Imperfections on the Buckling Stress of Cylindrical Shells

Techniques have been developed for making essentially "perfect" thin cylindrical shells and for making shells with definite types of initial deformations. The "perfect" shells give buckling stresses much higher than have previously been obtained. Initial deformations of the form ∆R= a(o) sin ((πx)/L) have been tested and ranges of positive a(o) were found in which there was no lowering of the buckling stress. Negative values of a(o) caused a decrease in the failure load. A theoretical solution which indicated the same trends as were found experimentally has been carried out.

CYLINDRICAL SHELL↗

NASA NTRS1972

Extreme-ultraviolet emission from solar prominences.

Spectra and spectroheliograms of prominences have been obtained at wavelengths of 300 to 1400 A from instruments aboard the OSO 4 and OSO 6 spacecraft. Quiescent prominences appear in emission above the limb for all strong lines formed at temperatures below 300,000 K, but not at higher temperatures. The gas pressure in the 100,000-K transition zone around prominences is approximately equal to that in the cooler (6500 K) central regions. The temperature and the hydrogen ground-state departure coefficient in the central regions are determined from the Lyman-continuum spectrum. Prominences on the disk (filaments) are visible in absorption in many lines, especially those at wavelengths below the hydrogen Lyman limit at 912 A.

Noyes, R. W.↗

NASA NTRS1984

LEED and AES characterization of the GaAs(110)-ZnSe interface

In this paper, a study is conducted of the composition and structure of epitaxial ZnSe films grown by congruent evaporation on GaAs(110) at a rate of 2 A/min. It is found that the films grown on 300 C GaAs are nearly stoichiometric and form an abrupt interface with the substrate. Films grown at higher temperature (T greater than 350-400 C) are Se rich. The crystallinity of films grown at 300 C is good and their surface atomic geometry is identical to that of a ZnSe crystal. The GaAs-ZnSe interface geometry seems to be dominated by the Se-substrate bonds. The adsorption of Se, during the formation of very thin ZnSe films (2-3 A), produces a (1 x 2) LEED pattern and modifications of the LEED I-V profiles, which probably indicate a change in the substrate atomic relaxation.

Tu, D.-W.↗

NASA NTRS1986

The effect of heavy ions on the formation and structure of cometary bow shocks

A hybrid simulation model is used to investigate the effects of heavy cometary ions on the formation and structure of a cometary bow shock. The calculations are carried out over various Mach numbers and heavy ion velocity distribution functions. The model is based on previous formulations for phenomena in the solar wind and at the earth's bow shock. The generation of the shock is described in terms of particles injected from one side of the simulation field and reflected from the other end of the field, i.e., a solid wall boundary model. This technique permits the steep buildup of the ion density near the cometary nucleus, followed by coupling of the incident and reflected ion streams to produce a shock. It is shown that at low Mach numbers (up to Mach 2) the shock is transitory and periodically formed by protons, then destroyed by heavy ions (O+). Slightly higher Mach numbers lead to a true stationary shock. An examination of coupling effects between the solar wind and the heavy ions at low Mach numbers by using the Rankine-Hugoniot relations reveals that the ions and the solar wind protons cannot be treated as a single fluid calculating the shock characteristics.

Omidi, N.↗

NASA NTRS1987

Constraint-based stereo matching

The major difficulty in stereo vision is the correspondence problem that requires matching features in two stereo images. Researchers describe a constraint-based stereo matching technique using local geometric constraints among edge segments to limit the search space and to resolve matching ambiguity. Edge segments are used as image features for stereo matching. Epipolar constraint and individual edge properties are used to determine possible initial matches between edge segments in a stereo image pair. Local edge geometric attributes such as continuity, junction structure, and edge neighborhood relations are used as constraints to guide the stereo matching process. The result is a locally consistent set of edge segment correspondences between stereo images. These locally consistent matches are used to generate higher-level hypotheses on extended edge segments and junctions to form more global contexts to achieve global consistency.

Kuan, D. T.↗