Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gas composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Multiplexed gas spectroscopy using tunable VCSELs

Detection and identification of gas species using tunable laser diode laser absorption spectroscopy has been performed using vertical cavity surface emitting lasers (VCSEL). Two detection methods are compared: direct absorbance and wavelength modulation spectroscopy (WMS). In the first, the output of a DC-based laser is directly monitored to detect for any quench at the targeted specie wavelength. In the latter, the emission wavelength of the laser is modulated by applying a sinusoidal component on the drive current of frequency {omega}, and measuring the harmonics component (2{omega}) of the photo-detected current. This method shows a better sensitivity measured as signal to noise ratio, and is less susceptible to interference effects such as scattering or fouling. Gas detection was initially performed at room temperature and atmospheric conditions using VCSELs of emission wavelength 763 nm for oxygen and 1392 nm for water, scanning over a range of approximately 10 nm, sufficient to cover 5-10 gas specific absorption lines that enable identification and quantization of gas composition. The amplitude and frequency modulation parameters were optimized for each detected gas species, by performing two dimensional sweeps for both tuning current and either amplitude or frequency, respectively. We found that the highest detected signal is observed for a wavelength modulation amplitude equal to the width of the gas absorbance lines, in good agreement with theoretical calculations, and for modulation frequencies below the time response of the lasers (<50KHz). In conclusion, we will discuss limit of detection studies and further implementation and packaging of VCSELs in diode arrays for continuous and simultaneous monitoring of multiple species in gaseous mixtures.

42 ENGINEERING↗

Low-energy ion implantation: Large mass fractionation of argon

The isotropic signatures of noble gases in the atmospheres of the Earth and other planets are considerably evolved when compared to signatures observed in the solar wind. The mechanisms driving the evolution of planetary volatiles from original compositions in the solar accretion disk are currently poorly understood. Modeling of noble-gas compositional histories requires knowledge of fractionating processes that may have operated through the evolutionary stages. Since these gases are chemically inert, information on noble-gas fractionation processes can be used as probes. The importance of understanding these processes extends well beyond 'noble-gas planetology.' Trapped argon acquired by low-energy implantation (approximately less than 100 eV) into solids is strongly mass fractionated (approximately greater than or equal to 3 percent/amu). This has potential implications for the origin and evolution of terrestrial planet atmospheres.

Ponganis, K. V.↗

Local composition activity coefficient model for mixed-gas adsorption equilibria

Taking into consideration the adsorbate–adsorbent interactions, a novel activity coefficient model is derived from the non-random two-liquid theory for mixed-gas adsorption equilibria. In contrast with the conventional activity coefficient models developed for bulk liquids, the new model correctly predicts negative deviations from ideality for adsorbed phase mixtures including azeotropic behavior exhibited by selected gas-adsorbent systems. Here, the requiring a single binary interaction parameter per adsorbate–adsorbate pair, the model successfully correlates wide varieties of binary adsorption isotherm data and it should be a powerful engineering thermodynamic tool in correlating and predicting mixed-gas adsorption equilibria.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical emission spectroscopic studies and comparisons of CH{sub 3}F/CO{sub 2} and CH{sub 3}F/O{sub 2} inductively coupled plasmas

A CH{sub 3}F/CO{sub 2} inductively coupled plasma (ICP), sustained in a compact plasma reactor, was investigated as a function of power (5–400 W) and feed gas composition, at a pressure of 10 mTorr, using optical emission spectroscopy and rare gas actinometry. Number densities of H, F, and O increased rapidly between 74% and 80% CO{sub 2}, ascribed to the transition from polymer-covered to polymer-free reactor walls, similar to that found previously in CH{sub 3}F/O{sub 2} ICPs at 48% O{sub 2}. Below 40% O{sub 2} or CO{sub 2}, relative emission intensity ratios were almost identical for most key species in CH{sub 3}F/O{sub 2} and CH{sub 3}F/CO{sub 2} ICPs except for higher OH/Xe (a qualitative measure of OH and H{sub 2}O densities) over the full range of CH{sub 3}F/O{sub 2} composition. The number density of H, F, and O increased with power in CH{sub 3}F/CO{sub 2} (20%/80%) plasmas (polymer-free walls), reaching 4.0, 0.34, and 1.6 × 10{sup 13}/cm{sup 3}, respectively, at 300 W. The CO number density increased with power and was estimated, based on self-actinometry, to be 8.8 × 10{sup 13}/cm{sup 3} at 300 W. The CO{sub 2} number density was independent of power below 40 W (where very little decomposition occurred), and then decreased rapidly with increasing power, reaching 2.8 × 10{sup 13}/cm{sup 3} at 300 W, corresponding to 83% dissociation. Films deposited on p-Si, 10 cm from the open, downstream end of the plasma reactor, were analyzed by x-ray photoelectron spectroscopy. Between 10% and 40% CO{sub 2} or O{sub 2} addition to CH{sub 3}F, film deposition rates fell and O content in the films increased. Faster deposition rates in CH{sub 3}F/CO{sub 2} plasmas were ascribed mainly to a larger thermodynamic driving force to form solid carbon, compared with CH{sub 3}F/O{sub 2} plasmas. Oxygen content in the films increased with increasing CO{sub 2} or O{sub 2} addition, but for the same deposition rate, no substantial differences were observed in the composition of the films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Properties of nano structured Ag-TiO{sub 2} composite coating on stainless steel using RF sputtering method

RF Sputtering system is one of the Physical Vapour Deposition (PVD) methods that have been widely used to produce hard coating. This technique is used to deposit thin layers of metallic substrates such as stainless steel (SS). From this process, a good adhesiveness and wear resistance coating can be produced for biomedical applications. In this study, RF sputtering method was used to deposit TiO{sub 2}-Ag composite coatings via various deposition parameters. The parameters are RF power of 350W, gas composition (Ar: O{sub 2}) 50:5 and deposition time at 1, 2, 4 and 6 hours. Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD) and Raman spectroscopy were used to characterize surface area of coated samples. The formation of nanocrystalline thin film and the surface morphology were examined using SEM. The crystallite size of TiO{sub 2}-Ag composite coatings were estimated between 20-60 nm based on XRD analysis using Scherer equation and SEM evaluation. The Raman and XRD results suggested that the structure of the TiO{sub 2}-Ag consist of anatase and rutile phases. It also showed that the intensity of anatase peaks increased after samples undergone annealing process at 500 Degree-Sign C.

36 MATERIALS SCIENCE↗

OPTIMIZATION OF A SOLAR SIMULATOR FOR PLANETARY-PHOTOCHEMICAL STUDIES

Low-temperature microwave-powered plasma based on hydrogen and hydrogen with noble gas mixtures are widely used as a continuous vacuum ultraviolet (VUV) source in laboratory experiments carried out to mimic the photochemistry in astrophysical environments. In this work, we present a study dedicated to optimizing such sources in terms of mono-chromaticity at Lyα (H(Lyα) line at 121.6 nm ∼ 10.2 eV) and high spectral irradiance. We report the influence on the emission spectrum of a wide range of experimental conditions including gas composition (pure H{sub 2}, pure He, and H{sub 2}/He mixture), gas pressure, flow rates, and microwave power. The absolute spectral irradiance delivered by this VUV light source has been measured. With a microwave input power of 100 W, the best conditions for producing a quasi-monochromatic source are a 1% H{sub 2}/He gas mixture at a total pressure of 5 mbar and a flow rate of 2 sccm. By changing the microwave input power from 30 to 120 W, H(Lyα) increases by more than one order of magnitude. A comparison between the current measurements and the solar VUV spectral irradiance is reported over 115–170 nm.

79 ASTRONOMY AND ASTROPHYSICS↗

Bedrock weathering rates, reactive nitrogen influxes and effluxes, and nitrous oxide emissions rates from the Pumphouse Hillslope, East River Watershed, Colorado

Atmospheric nitrous oxide contributes directly to global warming, yet models of the nitrogen cycle do not account for bedrock, the largest pool of terrestrial nitrogen, as a source of nitrous oxide. Although it is known that release rates of nitrogen from bedrock are large, there is an incomplete understanding of the connection between bedrock-hosted nitrogen and atmospheric nitrous oxide. Here, we quantify nitrogen fluxes and mass balances at a hillslope underlain by marine shale. We found that at this site bedrock weathering contributes 78% of the subsurface reactive nitrogen, while atmospheric sources (commonly regarded as the sole sources of reactive nitrogen in pristine environments) account for only the remaining 22%. About 56% of the total subsurface reactive nitrogen denitrifies, including 14% emitted as nitrous oxide. The remaining reactive nitrogen discharges in porewaters to a floodplain where additional denitrification likely occurs. We also found that the release of bedrock nitrogen occurs primarily within the zone of the seasonally fluctuating water table and suggest that the accumulation of nitrate in the vadoes zone, often attributed to fertilization and soil leaching, may also include contributions from weathered nitrogen-rich bedrock. Our hillslope study suggests that under oxygenated and moisture-rich conditions, weathering of deep, nitrogen-rich bedrock makes an important contribution to the nitrogen cycle. The data files are in Excel, which can be accessed using Microsoft Office, and consist of many data sets from the Pumphouse Hillslope PLM (Pumphouse Lower Montane) 1, 2, 3, and 4. They include soil to rock (0-10 meters) solid phase minerals and elements compositions; time- and depth-resolved pore-water chemistry and pore-gas compositions; time- and depth-resolved water table depths and water fluxes; subsurface weathering rates; nitrogen influxes and effluxes and mass balance. The attached paper is in a Word document, which can be accessed using Microsoft Office, and in pdf format.

54 ENVIRONMENTAL SCIENCES↗

Evaporation and combustion of LOX under supercritical and subcritical conditions

The objective is to study the evaporation and combustion of LOX under supercritical and subcritical conditions both experimentally and theoretically. In the evaporation studies, evaporation rate and surface temperature were measured when LOX vaporizing in helium environments at pressures ranging from 5 to 68 atm. A Varian 3700 gas chromatograph was employed to measure the oxygen concentration above the LOX surface. For the combustion tests, high-magnification video photography was used to record direct images of the flame shape of a LOX/H2/He laminar diffusion flame. The gas composition in the post-flame region is also being measured with the gas sampling and chromatography analysis. These data are being used to validate the theoretical model. A comprehensive theoretical model with the consideration of the solubility of ambient gases as well as variable thermophysical properties was formulated and solved numerically to study the gasification and burning of LOX at elevated pressures. The calculated flame shape agreed reasonably well with the edge of the observed luminous flame surface. The effect of gravity on the flame structure of laminar diffusion flames was found to be significant. In addition, the predicted results using the flame-sheet model were compared with those based upon full equilibrium calculations (which considered the formation of intermediate species) at supercritical pressures. Except at the flame front where temperature exceeded 2,800 K, the flame-sheet and equilibrium solutions in terms of temperature distributions were in very close agreement. The temperature deviation in the neighborhood of the flame front is caused by the effect of high-temperature dissociation.

Yang, A. S.↗

Pseudo-dynamic Aspen Plus{sup R} Model of the Defense Waste Processing Facility - 18475

The Defense Waste Processing Facility (DWPF) at the Savannah River Site converts legacy high-level waste from the Cold War into borosilicate glass for permanent disposal in a geological repository. The waste sludge is chemically adjusted by the addition of acid, mixed with frit, and concentrated in the DWPF Chemical Process Cell (CPC) to ensure that the final glass has the desired properties. The resulting mixture is fed into the melter where the waste is melted and poured into stainless steel storage canisters. We present an Aspen Plus{sup R} model of the DWPF CPC, which is being developed to aid chemical processing decisions pertaining to the current flowsheet and to aid decisions regarding optimizing future processing. Given a waste feed composition with acid and frit additions, the model will predict the sludge and off-gas compositions throughout the processing, as well as the final melter feed composition. This allows different processing scenarios to be investigated easily, reducing the reliance on experimental testing, and hence saving time and money. The model has multiple potential applications, including calculating the acid and frit additions required to give acceptable glass properties, off-gas permitting, tracking mercury steam-stripped from the waste in the off-gas system, tracking flammable gases in the offgas system, investigating the effect of reducing air purges in the condensers, and general process optimization. The waste is processed in the CPC in batches, requiring dynamic simulation to track the time-dependent operations. Accurate modeling of the processing also requires calculations of phase and electrolyte chemical equilibria and parallel rate-dependent reactions. Due to existing technical limitations with dynamic simulation of the complex chemical system, we have adopted a pseudo-dynamic approach in which time intervals are treated as consecutive steady-state operations in Aspen Plus{sup R}. Thus, the model consists of ∼100 replicas of the processing vessel and its off-gas system, with the sludge output by one replica (representing one time interval) becoming the feed to the next (representing the next time interval). By examining the results from these replicas in sequence, one can see the time evolution of the model. This general approach can be used wherever simultaneous calculation of phase and electrolyte chemical equilibria in a dynamically evolving system is needed. In addition to describing the general structure and chemistry of the model, we present results from tests of the model against experimental data. These data are from laboratory-scale process simulations of the CPC with a nonradioactive waste sludge simulant. These tests include the model's predictions of the offgas composition, the sludge pH, and the final sludge composition. We will also discuss planned future developments of the model. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Deposition of stress free c-axis oriented LiNbO{sub 3} thin film grown on (002) ZnO coated Si substrate

C-axis oriented lithium niobate thin films have been deposited on Si substrate using RF sputtering technique. A thin buffer layer of c-axis (002) oriented ZnO on Si substrate has been used as a nucleating layer to promote the growth of (006) oriented LiNbO{sub 3} film. The processing gas composition and pressure are found to be very critical in obtaining stress free LiNbO{sub 3} film having desired (006) orientation. The LiNbO{sub 3} films deposited under unique combination of sputtering pressure (10 mTorr) and argon percentage (80%) in reactive gas (Ar + O{sub 2}) composition become almost stress free having lattice parameter (1.3867 A) close to the bulk value. The observed variation in the structural properties and optical phonon modes observed by Raman spectroscopic studies of the oriented LiNbO{sub 3} thin film with stress has been correlated with growth kinetics.

36 MATERIALS SCIENCE↗

Abstract for CRADA between Solar Turbines Incorporated and NETL

The National Energy Technology Laboratory is developing the Raman Gas Analyzer (RGA) to be a fast, non-destructive instrument for on-line measurement of gas composition. The RGA has been demonstrated to have an extremely fast response (<1 second) multi-gas analysis capability. All but the noble gases are Raman active, but Raman interaction is weak with gas phase substances. The RGA uses a reflectively lined capillary as the optical cell in a patented configuration, providing both a small sample volume for fast gas exchange, and a much greater Raman signal collection than traditional instrument configurations. This allows very fast measurement of fuel gases (hydrogen, methane, ethane, propane) as well as other common industrial gases (including CO, CO2, N2, O2, H2O). The RGA provides a new enabling technology for faster, smarter process control based on the chemical composition of the gases in the process, such as improving fuel flexibility and efficiency for power generation systems. NETL has constructed a field prototype of the RGA to test the instrument performance in various applications in fossil energy. The objective of this CRADA is to field test the Raman Gas Analyzer in a commercial or near-commercial gas turbine application, to advance its Technology Readiness Level and support technology transfer to the commercial marketplace.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbon dioxide electrolysis with solid oxide electrolyte cells for oxygen recovery in life support systems

The direct electrochemical reduction of carbon dioxide (CO2) is achieved without catalysts and at sufficiently high temperatures to avoid carbon formation. The tubular electrolysis cell consists of thin layers of anode, electrolyte, cathode and cell interconnection. The electrolyte is made from yttria-stabilized zirconia which is an oxygen ion conductor at elevated temperatures. Anode and cell interconnection materials are complex oxides and are electronic conductors. The cathode material is a composite metal-ceramic structure. Cell performance characteristics have been determined using varying feed gas compositions and degrees of electrochemical decomposition. Cell test data are used to project the performance of a three-person CO2-electrolysis breadboard system.

Isenberg, Arnold O.↗

In situ measurements of thermospheric composition, temperature, and winds by mass spectrometry

Mass spectrometry, in which a beam of electrons ionizes a sample of atmospheric gas and then analyses the ions thus produced to determine the concentration of each species in the sample, is presently evaluated as a basis for the study of earth atmosphere and other planetary atmospheres' properties. Recent applications of in situ mass spectrometry have measured thermospheric neutral gas composition, temperatures, and winds, with a spatial resolution sufficiently high to reveal previously unsuspected atmospheric variability. It is expected that analyses of these data will lead to a more detailed understanding of the deposition processes governing the thermosphere's highly variable structure.

Spencer, N. W.↗

Effect of Coal Properties and Operation Conditions on Flow Behavior of Coal Slag in Entrained Flow Gasifiers: A Brief Review

Integrated gasification combined cycle (IGCC) is a potentially promising clean technology with an inherent advantage of low emissions, since the process removes contaminants before combustion instead of from flue gas after combustion, as in a conventional coal steam plant. In addition, IGCC has potential for cost-effective carbon dioxide capture. Availability and high capital costs are the main challenges to making IGCC technology more competitive and fully commercial. Experiences from demonstrated IGCC plants show that, in the gasification system, low availability is largely due to slag buildup in the gasifier and fouling in the syngas cooler downstream of the gasification system. In the entrained flow gasifiers used in IGCC plants, the majority of mineral matter transforms to liquid slag on the wall of the gasifier and flows out the bottom. However, a small fraction of the mineral matter (as fly ash) is entrained with the raw syngas out of the gasifier to downstream processing. This molten/sticky fly ash could cause fouling of the syngas cooler. Therefore, it is preferable to minimize the quantity of fly ash and maximize slag. In addition, the hot raw syngas is cooled to convert any entrained molten fly slag to hardened solid fly ash prior to entering the syngas cooler. To improve gasification availability through better design and operation of the gasification process, better understanding of slag behavior and characteristics of the slagging process are needed. Slagging behavior is affected by char/ash properties, gas compositions in the gasifier, the gasifier wall structure, fluid dynamics, and plant operating conditions (mainly temperature and oxygen/carbon ratio). The viscosity of the slag is used to characterize the behavior of the slag flow and is the dominating factor to determine the probability that ash particles will stick. Slag viscosity strongly depends on the temperature and chemical composition of the slag. Because coal has varying ash content and composition, different operating conditions are required to maintain the slag flow and limit problems downstream. This report briefly introduces the IGCC process, the gasification process, and the main types and operating conditions of entrained flow gasifiers used in IGCC plants. This report also discusses the effects of coal ash and slag properties on slag flow and its qualities required for the entrained flow gasifier. Finally this report will identify the key operating conditions affecting slag flow behaviors, including temperature, oxygen/coal ratio, and flux agents.

01 COAL, LIGNITE, AND PEAT↗

Venus ionosphere - Photochemical and thermal diffusion control of ion composition

The major photochemical sources and sinks for ten of the ions measured by the ion mass spectrometer on the Pioneer Venus bus and orbiter spacecraft that are consistent with the neutral gas composition measured on the same spacecraft are identified. The neutral gas temperature (as a function of solar zenith angle) derived from measured ion distributions in photochemical equilibrium is given. Above 200 kilometers, the altitude behavior of ions is generally controlled by plasma diffusion, with important modifications for minor ions due to thermal diffusion resulting from the observed gradients of plasma temperatures. The dayside equilibrium distributions of ions are sometimes perturbed by plasma convection, while lateral transport of ions from the dayside seems to be a major source of the nightside ionosphere.

Bauer, S. J.↗

Correlation of chemical composition and electrical properties of rf sputtered alumina films

Alumina films were prepared by radio frequency magnetron sputtering from an aluminum oxide target on an indium tin oxide covered glass. The purpose of the study was to test the influence of the sputter parameters on the elemental composition, surface morphology, and electrical insulation properties (breakdown fields and leakage currents). Tested parameters were the sputter gas (Ar) pressure, the sputter rate, the sputter power, the sputter gas composition (Ar:O{sub 2}), the conditioning of the target, the residual base pressure, and the substrate temperature. The surface morphology of the films was investigated by atomic force microscopy. Depth profiles of the elemental compositions were measured by elastic recoil detection using energetic heavy ions, and the insulation properties were investigated by current voltage measurements and impedance spectroscopy. The main finding is that the leakage currents increase by about five orders of magnitude, if the atomic ratio of O:Al increases from 1.35 to 2.0. In parallel the breakdown fields decrease by a factor of 100, and the character of the breakdowns changes from soft to hard. The highest breakdown fields (2.4 MV/cm) and smallest leakage currents (6.5x10{sup -8} A/cm{sup 2} at 2.0 MV/cm) are obtained for slightly Al rich films with small atomic concentrations of H (<0.5 at. %). These films were sputtered in pure Ar and under the lowest possible pressure of the residual gas.

36 MATERIALS SCIENCE↗

Evaluating Separation Selectivity and Collision Cross Section Measurement Reproducibility in Helium, Nitrogen, Argon, and Carbon Dioxide Drift Gases for Drift Tube Ion Mobility–Mass Spectrometry

Previous ion mobility (IM) studies have demonstrated that varying the drift gas composition can be used to enhance chemical selectivity and resolution, yet there are few drift gas studies aimed at achieving quantitatively reproducible mobility measurements. Here, we critically evaluate the conditions necessary to achieve reproducible collision cross section (CCS) measurements in pure drift gases (helium, nitrogen, argon, and carbon dioxide) using a commercial uniform field drift tube instrument. Optimal experimental parameters are assessed based on the convergence of CCS measurements to reproducible values which are compared with literature values. A suite of calibration standards with diverse masses, biological classes, and charge states are examined to assess chemical selectivity and resolution achievable in each drift gas. Results indicate nitrogen and argon perform similarly and are sufficient for most applications where high resolving power and high peak capacity are desired. Carbon dioxide exhibits more selectivity for resolving structurally heterogeneous compounds, which may be preferable in specific analyte pair separations. Helium demonstrated modest separation capabilities but has utility for comparison to theoretical values and previously published work. In drift gases other than nitrogen, pressure differentials up to 230 mTorr between the drift tube and upstream chamber were optimal for improving correlation to literature values, while in nitrogen, the recommended pressure differential of 150 mTorr was found appropriate. We present recommended experimental parameters as well as gas-specific CCS measurements for structurally homogeneous sets of analytes which are suitable for use by other laboratories as standards for purposes of instrument calibration and overall assessment of IM separation performance. .

74 ATOMIC AND MOLECULAR PHYSICS↗

Treatment surfaces with atomic oxygen excited in dielectric barrier discharge plasma of O{sub 2} admixed to N{sub 2}

This paper describes the increase in surface energy of substrates by their treatment with gas composition generated in plasmas of DBD (Dielectric Barrier Discharge) in O2 admixed with N2. Operating gas dissociation and excitation was occurred in plasmas developed in two types of reactors of capacitively-coupled dielectric barrier configurations: coaxial cylindrical, and flat rectangular. The coaxial cylindrical type comprised an inner cylindrical electrode encapsulated in a ceramic sheath installed coaxially inside a cylindrical ceramic (quartz) tube passing through an annular outer electrode. Components of the flat rectangular type were a flat ceramic tube of a narrow rectangular cross section supplied with two flat electrodes mounted against one another outside of the long parallel walls of this tube. The operating gas, mixture of N{sub 2} and O{sub 2}, was flowing in a completely insulated discharge gap formed between insulated electrodes of the devices with an average velocity of gas inlet of about 7 to 9 m/s. Dielectric barrier discharge plasma was excited in the operating gaps with a bipolar pulse voltage of about 6 kV for 2 ms at 50 kHz repetition rate applied to the electrodes of the coaxial device, and of about 14 kV for 7 ms at 30 kHz repetition rate for the flat linear device. A lifetime of excited to the 2s{sup 2}2p{sup 4}({sup 1}S{sub 0}) state in DBD plasma and streaming to the surfaces with a gas flow atomic oxygen, responsible presumably for treating surfaces, exceeded 10 ms in certain cases, that simplified its separation from DBD plasma and delivery to substrates. As it was found in particular, surfaces of glass and some of polymers revealed significant enhancement in wettability after treatment.

36 MATERIALS SCIENCE↗