SEARCH · Engineering Papers

Results for “flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Theoretical and experimental study of flow through turbine cascades with coolant flow injection

An analytical study is presented which deals with the change in the outlet flow conditions from a turbine blade row due to coolant air injection through slots. The analysis applies to small secondary to primary mass flow ratios, taking into consideration the change in boundary layer development resulting from injection. The effects of injection location, injection flow angle and injected air momentum flux are investigated. The results of the present analysis are compared with the values obtained using the mixing theory method and experimental data from cold flow tests in a turbine cascade tunnel.

Tabakoff, W.↗

NASA NTRS1975

Critical flow and pressure ratio data for LOX flowing through nozzles

LOX and LN2 data for two-phase critical flow through nozzles have been acquired with precision control. The principal measured parameters were inlet conditions, critical flow rate and critical flow pressure ratio. The data conclusively demonstrate that the principle of corresponding states can be applied to two-phase choked flow through nozzles. These data also demonstrate that the proper normalizing parameters have been developed and current theories can provide an adequate means for extrapolating to other fluids.

Hendricks, R. C.↗

NASA NTRS1977

Effect of coolant flow ejection on aerodynamic performance of low-aspect-ratio vanes. 2: Performance with coolant flow ejection at temperature ratios up to 2

The aerodynamic performance of a 0.5 aspect ratio turbine vane configuration with coolant flow ejection was experimentally determined in a full annular cascade. The vanes were tested at a nominal mean section ideal critical velocity ratio of 0.890 over a range of primary to coolant total temperature ratio from 1.0 to 2.08 and a range of coolant to primary total pressure ratio from 1.0 to 1.4 which corresponded to coolant flows from 3.0 to 10.7 percent of the primary flow. The variations in primary and thermodynamic efficiency and exit flow conditions with circumferential and radial position were obtained.

Hass, J. E.↗

NASA NTRS1978

Effects of grazing flow on the steady-state flow resistance and acoustic impedance of thin porous-faced liners

The effects of grazing flow on the steady state flow resistance and acoustic impedance of seven Feltmetal and three Rigimesh thin porous faced liners were studied. The steady-state flow resistance of the ten specimens was measured using standard fluid mechanical experimental techniques. The acoustic impedance was measured using the two microphone method. The principal findings of the study are that the effects of grazing flow were measured and found to be small; small differences were measured between steady-state and acoustic resistance, and a semi-empirical model was derived that correlated the steady-state resistance data of the seven Feltmetal liners and the face sheet reactance of both the Feltmetal and Rigimesh liners.

Hersh, A. S.↗

NASA NTRS1977

A kinematic investigation of the influence of anvil air flow over convective nephsystems on high-level horizontal flow

The interactions between horizontal ambient flow and divergent wind fields, such as those that obtain atop cumulonimbus complexes, were investigated (theoretically) kinematically. The following were observed from the results of the analyses. First, for a particular divergent field, the relative mass flux over the area of the nephsystem decreased as the strength of the horizontal flow increased. Secondly, while in some of the cases analyzed the interaction between the two flows only resulted in the fanning out of streamlines and a slight redistribution in the wind speed, in many cases backflows and a total reorganization of the wind field occurred. Backflows have a blocking effect on the horizontal flow. Some of the computed patterns were compared with upper level cloud vectors (from geostationary satellite photographs). The comparison indicated that the computed resultant wind field could be used to explain some features of such satellite-derived wind fields.

Balogun, E. E.↗

NASA NTRS1979

Flow friction of the turbulent coolant flow in cryogenic porous cables

Considered are cryogenic power transmission cables with porous cores. Calculations of the turbulent coolant flow with injection or suction through the porous wall are presented within the framework of a two-layer model. Universal velocity profiles were obtained for the viscous sublayer and flow core. Integrating the velocity profile, the law of flow friction in the pipe with injection has been derived for the case when there is a tangential injection velocity component. The effect of tangential velocity on the relative law of flow friction is analyzed. The applicability of the Prandtl model to the problem under study is discussed. It is shown that the error due to the acceptance of the model increases with the injection parameter and at lower Reynolds numbers; under these circumstances, the influence of convective terms in the turbulent energy equation on the mechanism of turbulent transport should be taken into account.

Hendricks, R. C.↗

NASA NTRS1978

Flap survey test of a combined surface blowing model: Flow measurements at static flow conditions

The Combined Surface Blowing (CSB) V/STOL lift/propulsion system consists of a blown flap system which deflects the exhaust from a turbojet engine over a system of flaps deployed at the trailing edge of the wing. Flow measurements consisting of velocity measurements using split film probes and total measure surveys using a miniature Kiel probe were made at control stations along the flap systems at two spanwise stations, the centerline of the nozzle and 60 percent of the nozzle span outboard of the centerline. Surface pressure measurements were made in the wing cove and the upper surface of the first flap element. The test showed a significant flow separation in the wing cove. The extent of the separation is so large that the flow into the first flap takes place only at the leading edge of the flap. The velocity profile measurements indicate that large spanwise (3 dimensional) flow may exist.

Fukushima, T.↗

NASA NTRS1982

Characteristics of the flow in the annulus-wall region of an axial-flow compressor rotor blade passage

Three-dimensional characteristics of the mean velocity and turbulence structure in the annulus-wall region of a moderately loaded compressor rotor have been investigated experimentally by employing triaxial hot-wire probes. Results are presented which indicate that the flow within and downstream of the rotor passage is highly complex due to the interaction of the annulus-wall boundary layer, blade boundary layers, tip leakage flow, and passage secondary flow. An understanding of the reported viscous flow interactions is important for establishing improved aerodynamic design criteria and efficiency, for predicting noise levels, and for determining the stall, surge, vibration, and flutter characteristics of turbomachinery.

Davino, R. M.↗

NASA NTRS1983

Pressure difference-flow rate variation in a femoral artery branch casting of man for steady flow

In-vitro, steady flow in a casting of the profunda femoris branch of the femoral artery of man was studied by measuring pressure differences in the main lumen and also in the branch over a large Reynolds number range from 200 to 1600. Effects of viscous and inviscid flows in this femoral artery branch were demonstrated quantitatively. The critical ratio of the flow rate in the branch to the upstream main lumen in this casting was found to be 0.4, above which the inviscid flow analysis indicated a pressure rise and below which it yielded a pressure drop in the main lumen across the branch junction. Pressure rises were experimentally found to occur both in the main lumen and in the branch for certain ranges of the aforementioned ratio.

Cho, Y. I.↗

NASA NTRS1984

The Mauna Loa sulfur flow as an analog to secondary sulfur flows on Io

Independent evidence suggests that both sulfur and silicate materials exist on the surface of Io. Spectral data indicate the presence of sulfur compounds, some of which are suggested to be of fumarolic origin. Morphological evidence and inferences of the physical properties of some land-forms suggest that silicate volcanism has occurred, which would involve temperatures 650 C or greater. Because the liquidus of sulfur is only about 115 C, it is likely that sulfur in close proximity to 'hot spots' or to active silicate volcanic areas on Io would be melted and mobilized as flows. The Mauna Loa sulfur flow may serve as an analog for such flows, as it consists of fumarolic sulfur that was melted as a consequence of a basaltic eruption and produced a small flow superimposed on silicate lavas.

Greeley, R.↗

NASA NTRS1985

A three-dimensional incompressible flow simulation method and its application to the Space Shuttle main engine. II Turbulent flow

An implicit finite difference code cast in general curvilinear coordinates is further developed for three-dimensional incompressible turbulent flows. The code is based on the method of pseudocompressibility and utilizes the Beam and Warming implicit approximate factorization algorithm to achieve computational efficiency. A multiple-zone method is further extended to include composite-grids to overcome the excessive computer memory required for solving turbulent flows in complex three-dimensional geometries. A simple turbulence model is proposed for internal flows. The code is being used for the Space Shuttle Main Engine (SSME) internal flow analyses.

Chang, J. L. C.↗

NASA NTRS1987

Compressible flow in a diffusing S-duct with flow separation

Local flow velocity vectors, as well as static and total pressures along ten radial traverses, were obtained at six stations for secondary flows in a diffusing 30-30-deg S-duct with circular cross section. The strong secondary flow measured in the first bend continued into the second with new vorticity produced in the opposite direction. Contour plots representing the transverse velocity field, as well as total and static pressure contours, have been obtained. As a result of the secondary flow and subsequent separation, substantial total pressure distortion is noted to occur at the duct exit.

Vakili, A. D.↗

NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

Boundary layer flow and turbulence transport analyses to study the influence of the free-stream turbulence on the surface heat transfer rate and the skin friction around the stagnation point of a circular cylinder in a turbulent flow are presented. The analyses are formulated with the turbulent boundary layer equations, the Reynolds stress transport equations and the k - epsilon two-equation turbulence modeling. The analyses are used to calculate the time-averaged turbulence double correlations, the mean flow properties, the surface heat transfer rate and the skin friction with an isotropic turbulence in the freestream. The analytical results are described and compared with the existing experimental measurements. Depending on the free-stream turbulence properties, the turbulence kinetic energy can increase or decrease as the flow moves toward the surface. However, the turbulence kinetic energy induces large Reynolds normal stresses at the boundary layer edge. The Reynolds normal stresses change the boundary layer profiles of the time-averaged double correlations of the velocity and temperature fluctuations, the surface heat transfer rate and the skin friction. The free-stream turbulence dissipation rate can affect the stagnation-point heat transfer rate but the influence of the free-stream temperature fluctuation on the heat transfer rate is insignificant.

Wang, Chi R.↗

NASA NTRS1988

Three-dimensional viscous flow computations of a circular jet in subsonic and supersonic cross flow

Three-dimensional viscous flow computations are presented for 90 deg. injection angle jets in subsonic and supersonic crossflow. Comparisons with experimental data include jet centerline and vortex trajectories for the subsonic crossflow, and surface pressure measurement for the supersonic crossflow case. The vortices induced in the jet/freestream interaction are computed and illustrated. The vortices persist in subsonic flow and die out quickly in supersonic flow. The structure of the shocks in the unconfined supersonic flow is illustrated.

Harloff, G. J.↗

NASA NTRS1988

The mean flow structure around and within a turbulent junction or horseshoe vortex. II - The separated and junction vortex flow

Five-hole probe measurements of the flow through the separation region and in the vortex system of an incompressible subsonic flow around and within a turbulent junction or horseshoe vortex are reported. Mean velocity, static pressure, and total pressure results are presented. The streamwise vorticity field is obtained from the measured velocity field. Flow visualization results for the floor and cylinder surface agree well with the flow field data.

Pierce, F. J.↗

NASA NTRS1989

On the separated flow upstream of a jet in a cross flow

Flow visualization techniques have been used to investigate the complex flow in the recirculation region upstream of a rectangular jet issuing normally into a uniform cross flow. Two different flow regimes are identified. It is shown that the recirculation region upstream of the jet is unsteady and periodic. Two distinct vortical structures are found for the wake behind the jet, one dominated by a symmetric vortex pair and one with vortices shed alternately from each side of the jet.

Krothapalli, A.↗

NASA NTRS1989

Modeling of turbulence for compression corner flows and internal flows

A compressible Reynolds averaged Navier-Stokes code is applied to examine the performances of basic turbulence models for unseparated and separated flows. The turbulence models considered are a zero-equation model and several two-equation models, including a new k-epsilon model with an eddy viscosity damping function depending upon the Reynolds number and the distance from the wall. The turbulence models are assessed using the following experimental flows: a channel flow, a backward facing step, and a two-dimensional compression corner at Mach 2.8. Discussions and comparisons of the experimental and numerical results are given. Mesh refinement is shown to have a significant beneficial effect on free shear layer flow results obtained with two-equation turbulence models. The results illustrate the usefulness of several turbulence models as a design tool for fluid engineering systems.

Champney, J. M.↗

NASA NTRS1987

Research in Natural Laminar Flow and Laminar-Flow Control, part 1

Since the mid 1970's, NASA, industry, and universities have worked together to conduct important research focused at developing laminar flow technology that could reduce fuel consumption for general aviation, commuter, and transport aircraft by as much as 40 to 50 percent. The symposium was planned in view of the recent accomplishments within the areas of laminar flow control and natural laminar flow, and the potential benefits of laminar flow technology to the civil and military aircraft communities in the United States. Included were technical sessions on advanced theory and design tool development; wind tunnel and flight research; transition measurement and detection techniques; low and high Reynolds number research; and subsonic and supersonic research.

Hefner, Jerry N.↗