Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flexible models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Model reduction and control of flexible structures using Krylov subspaces

Krylov vectors and the concept of parameter-matching are combined to develop a model reduction algorithm for a damped structural dynamics system. The reduced-order model obtained matches a certain number of low-frequency moments of the full-order system. The major application of the present method is to the control of flexible structures. It is shown that, in the control of flexible structures, there generally exist three types of control energy spillover, namely, the control spillover, the observation spillover, and dynamic spillover. The formulation based on Krylov subspaces can eliminate the control and the observation spillover, while leaving only the dynamic spillover to be considered. Two examples are used to illustrate the efficacy of the Krylov method.

Craig, Roy R., Jr.↗
NASA NTRS1985

Structural response of a rotating bladed disk to rotor whirl

A set of high speed rotating whirl experiments were performed in the vacuum of the MIT Blowdown Compressor Facility on the MIT Aeroelastic Rotor, which is structurally typical of a modern high bypass ratio turbofan stage. These tests identified the natural frequencies of whirl of the rotor system by forcing its response using an electromagnetic shaker whirl excitation system. The excitation was slowly swept in frequency at constant amplitude for several constant rotor speeds in both a forward and backward whirl direction. The natural frequencies of whirl determined by these experiments were compared to those predicted by an analytical 6 DOF model of a flexible blade-rigid disk-flexible shaft rotor. The model is also presented in terms of nondimensional parameters in order to assess the importance of the interation between the bladed disk dynamics and the shaft-disk dynamics. The correlation between the experimental and predicted natural frequencies is reasonable, given the uncertainty involved in determining the stiffness parameters of the system.

Crawley, E. F.↗
NASA NTRS1986

A methodology for airplane parameter estimation and confidence interval determination in nonlinear estimation problems

An algorithm for maximum likelihood (ML) estimation is developed with an efficient method for approximating the sensitivities. The ML algorithm relies on a new optimization method referred to as a modified Newton-Raphson with estimated sensitivities (MNRES). MNRES determines sensitivities by using slope information from local surface approximations of each output variable in parameter space. With the fitted surface, sensitivity information can be updated at each iteration with less computational effort than that required by either a finite-difference method or integration of the analytically determined sensitivity equations. MNRES eliminates the need to derive sensitivity equations for each new model, and thus provides flexibility to use model equations in any convenient format. A random search technique for determining the confidence limits of ML parameter estimates is applied to nonlinear estimation problems for airplanes. The confidence intervals obtained by the search are compared with Cramer-Rao (CR) bounds at the same confidence level. The degree of nonlinearity in the estimation problem is an important factor in the relationship between CR bounds and the error bounds determined by the search technique. Beale's measure of nonlinearity is developed in this study for airplane identification problems; it is used to empirically correct confidence levels and to predict the degree of agreement between CR bounds and search estimates.

Murphy, P. C.↗
NASA NTRS1985

Adaptive control of large space structures using recursive lattice filters

The use of recursive lattice filters for identification and adaptive control of large space structures is studied. Lattice filters were used to identify the structural dynamics model of the flexible structures. This identification model is then used for adaptive control. Before the identified model and control laws are integrated, the identified model is passed through a series of validation procedures and only when the model passes these validation procedures is control engaged. This type of validation scheme prevents instability when the overall loop is closed. Another important area of research, namely that of robust controller synthesis, was investigated using frequency domain multivariable controller synthesis methods. The method uses the Linear Quadratic Guassian/Loop Transfer Recovery (LQG/LTR) approach to ensure stability against unmodeled higher frequency modes and achieves the desired performance.

Sundararajan, N.↗
NASA NTRS1986

Active control of propeller induced noise fields inside a flexible cylinder

An active noise control model has been evaluated for reducing aircraft interior noise. The structural noise transmission properties of an aircraft fuselage were modelled as a flexible cylinder excited by external acoustic dipoles simulating the noise produced by twin propellers. The amplitudes of an internal distribution of monopole control sources were determined such that the area-weighted mean square acoustic pressure was minimized in the propeller plane. The noise control model was evaluated at low frequencies corresponding to the blade passage frequency and first few harmonics of a typical turbo-prop aircraft. Interior noise reductions of 20 25 dB were achieved, over a substantial region of the cylindrical cross-section, with just a few monopole control sources. The most favorable interior noise reductions were achieved when the active noise control model was used in combination with propeller source phasing.

Lester, H. C.↗
NASA NTRS1992

A piecewise continuous Timoshenko beam model for the dynamic analysis of tapered beam-like structures

Distributed parameter modeling offers a viable alternative to the finite element approach for modeling large flexible space structures. The introduction of the transfer matrix method into the continuum modeling process provides a very useful tool to facilitate the distributed parameter model applied to some more complex configurations. A uniform Timoshenko beam model for the estimation of the dynamic properties of beam-like structures has given comparable results. But many aeronautical and aerospace structures are comprised of non-uniform sections or sectional properties, such as aircraft wings and satellite antennas. This paper proposes a piecewise continuous Timoshenko beam model which is used for the dynamic analysis of tapered beam-like structures. A tapered beam is divided into several segments of uniform beam elements. Instead of arbitrarily assumed shape functions used in finite element analysis, the closed-form solution of the Timoshenko beam equation is used. Application of the transfer matrix method relates all the elements as a whole. By corresponding boundary conditions and compatible conditions a characteristic equation for the global tapered beam has been developed, from which natural frequencies can be derived. A computer simulation is shown in this paper, and compared with the results obtained from the finite element analysis. While piecewise continuous Timoshenko beam model decreases the number of elements significantly; comparable results to the finite element method are obtained.

Shen, Ji Yao↗
NASA NTRS1990

Identification and control of a flexible beam using modal domain sensor

The use of a distributed-effect, modal domain optical fiber sensor (MD sensor) as a component in an active control system to suppress vibrations in a flexible beam is discussed. The sensor model is integrated into the model for a flexible structure. Based on this system model, a control system with a dynamic compensator is designed to add damping to the low order modes of the flexible structure. To verify the modeling procedure, a cantilevered beam was instrumental with a piezoelectric actuator and an MD sensor. It is shown that experimental responses closely match simulated responses for both open loop and closed loop tests.

Cox, David E.↗
NASA NTRS1991

Modeling of the slewing control of a flexible structure

This paper presents a formulation for the modeling of a single-link flexible beam that is undergoing slewing motion at an actively controlled pinned end, where the other end of the beam is free. This pinned end, or slewing axis, is of fixed orientation such that the beam rotates in the horizontal plane. A geared dc electric motor is connected to the beam at the slewing axis. A position and a velocity sensor are placed at this hinged location, and their proportional feedback provides a position control system about the slewing axis. The motor characteristics, gear ratio, and the position feedback constant determine an equivalent rotational spring constant, often called the servo stiffness. This paper generalizes the structure's boundary conditions at the slewing axis to include the effects of the servo system. It is shown that the clamped-free beam assumption for the dynamics of the structure is a valid assumption if the ratio of the servo stiffness to beam flexibility is high. However, for moderate or low values of this ratio, the clamped-free beam leads to erroneous system models so that it becomes necessary to consider the effects of the driving servo on the dynamics of the flexible beam.

Garcia, Ephrahim↗
NASA NTRS1975

Coordinate transformation and truncation for rotating spacecraft with flexible appendages

The analytical structures of alternative coordinate transformations for the variables that characterize the deformations of finite element models of flexible appendages on rotating spacecraft are examined. Particular emphasis is given to the truncation operations that are essential for efficient numerical simulations of flexible spacecraft, due to the necessarily large number of coordinates employed in a finite element description. A theorem is developed which establishes necessary conditions for the commutativity of the required truncation and inversion operations. The recommended alternative for the rotating elastic appendage is a complex transformation with previously published orthogonality properties, which permit the derivation in this paper of a relatively simple explicit set of transformed and truncated equations of modal vibration in real variables.

Likins, P.↗
NASA NTRS1990

Verification of component mode techniques for flexible multibody systems

Investigations were conducted in the modeling aspects of flexible multibodies undergoing large angular displacements. Models were to be generated and analyzed through application of computer simulation packages employing the 'component mode synthesis' techniques. Multibody Modeling, Verification and Control Laboratory (MMVC) plan was implemented, which includes running experimental tests on flexible multibody test articles. From these tests, data was to be collected for later correlation and verification of the theoretical results predicted by the modeling and simulation process.

Wiens, Gloria J.↗
NASA NTRS1990

On dynamics and control of multi-link flexible space manipulators

In this paper dynamics, inverse dynamics, and control problems for multi-link flexible space manipulators are presented. In deriving the flexible manipulator dynamics the following are assumed: flexible deformations are relatively small; angular rates of the links are much smaller than their fundamental frequencies; nonlinear terms (centrifugal and Coriolis forces) in the flexible manipulator model are the same as those in the rigid body model. These assumptions are reasonable for large space manipulators, such as the space crane. Flexible displacements are measured with respect to the rigid body configuration, for which a linear time-varying system is obtained. The inverse dynamics problem consists of determination of joint torques, given tip trajectory, such that joint angles in flexible configuration are equal to the angles in the rigid body configuration. The manipulator control system consists of the feedforward compensation and feedback control loops. Simulation results of a two-link space crane with large payload show that the performance of this linearized dynamics and control approach is reasonable and robust subject to parameter variations during slew operations.

Gawronski, W.↗
NASA NTRS1996

Consideration in selecting crops for the human-rated life support system: a Linear Programming model

A Linear Programming model has been constructed which aids in selecting appropriate crops for CELSS (Controlled Environment Life Support System) food production. A team of Controlled Environment Agriculture (CEA) faculty, staff, graduate students and invited experts representing more than a dozen disciplines, provided a wide range of expertise in developing the model and the crop production program. The model incorporates nutritional content and controlled-environment based production yields of carefully chosen crops into a framework where a crop mix can be constructed to suit the astronauts' needs. The crew's nutritional requirements can be adequately satisfied with only a few crops (assuming vitamin mineral supplements are provided) but this will not be satisfactory from a culinary standpoint. This model is flexible enough that taste and variety driven food choices can be built into the model.

NASA Center JSC↗
NASA NTRS2017

Nonlinear Large Deflection Theory with Modified Aeroelastic Lifting Line Aerodynamics for a High Aspect Ratio Flexible Wing

This paper investigates the effect of nonlinear large deflection bending on the aerodynamic performance of a high aspect ratio flexible wing. A set of nonlinear static aeroelastic equations are derived for the large bending deflection of a high aspect ratio wing structure. An analysis is conducted to compare the nonlinear bending theory with the linear bending theory. The results show that the nonlinear bending theory is length-preserving whereas the linear bending theory causes a non-physical effect of lengthening the wing structure under the no axial load condition. A modified lifting line theory is developed to compute the lift and drag coefficients of a wing structure undergoing a large bending deflection. The lift and drag coefficients are more accurately estimated by the nonlinear bending theory due to its length-preserving property. The nonlinear bending theory yields lower lift and span efficiency than the linear bending theory. A coupled aerodynamic-nonlinear finite element model is developed to implement the nonlinear bending theory for a Common Research Model (CRM) flexible wing wind tunnel model to be tested in the University of Washington Aeronautical Laboratory (UWAL). The structural stiffness of the model is designed to give about 10% wing tip deflection which is large enough that could cause the nonlinear deflection effect to become significant. The computational results show that the nonlinear bending theory yields slightly less lift than the linear bending theory for this wind tunnel model. As a result, the linear bending theory is deemed adequate for the CRM wind tunnel model.

Aeroelasticity↗
NASA NTRS1998

High Performance, Robust Control of Flexible Space Structures: MSFC Center Director's Discretionary Fund

Many spacecraft systems have ambitious objectives that place stringent requirements on control systems. Achievable performance is often limited because of difficulty of obtaining accurate models for flexible space structures. To achieve sufficiently high performance to accomplish mission objectives may require the ability to refine the control design model based on closed-loop test data and tune the controller based on the refined model. A control system design procedure is developed based on mixed H2/H(infinity) optimization to synthesize a set of controllers explicitly trading between nominal performance and robust stability. A homotopy algorithm is presented which generates a trajectory of gains that may be implemented to determine maximum achievable performance for a given model error bound. Examples show that a better balance between robustness and performance is obtained using the mixed H2/H(infinity) design method than either H2 or mu-synthesis control design. A second contribution is a new procedure for closed-loop system identification which refines parameters of a control design model in a canonical realization. Examples demonstrate convergence of the parameter estimation and improved performance realized by using the refined model for controller redesign. These developments result in an effective mechanism for achieving high-performance control of flexible space structures.

Whorton, M. S.↗
NASA NTRS1998

Free-Suspension Residual Flexibility Testing of Space Station Pathfinder: Comparison to Fixed-Base Results

Application of the free-suspension residual flexibility modal test method to the International Space Station Pathfinder structure is described. The Pathfinder, a large structure of the general size and weight of Space Station module elements, was also tested in a large fixed-base fixture to simulate Shuttle Orbiter payload constraints. After correlation of the Pathfinder finite element model to residual flexibility test data, the model was coupled to a fixture model, and constrained modes and frequencies were compared to fixed-base test. modes. The residual flexibility model compared very favorably to results of the fixed-base test. This is the first known direct comparison of free-suspension residual flexibility and fixed-base test results for a large structure. The model correlation approach used by the author for residual flexibility data is presented. Frequency response functions (FRF) for the regions of the structure that interface with the environment (a test fixture or another structure) are shown to be the primary tools for model correlation that distinguish or characterize the residual flexibility approach. A number of critical issues related to use of the structure interface FRF for correlating the model are then identified and discussed, including (1) the requirement of prominent stiffness lines, (2) overcoming problems with measurement noise which makes the antiresonances or minima in the functions difficult to identify, and (3) the use of interface stiffness and lumped mass perturbations to bring the analytical responses into agreement with test data. It is shown that good comparison of analytical-to-experimental FRF is the key to obtaining good agreement of the residual flexibility values.

Tinker, Michael L.↗
NASA NTRS2012

Quasi 1D Modeling of Mixed Compression Supersonic Inlets

The AeroServoElasticity task under the NASA Supersonics Project is developing dynamic models of the propulsion system and the vehicle in order to conduct research for integrated vehicle dynamic performance. As part of this effort, a nonlinear quasi 1-dimensional model of the 2-dimensional bifurcated mixed compression supersonic inlet is being developed. The model utilizes computational fluid dynamics for both the supersonic and subsonic diffusers. The oblique shocks are modeled utilizing compressible flow equations. This model also implements variable geometry required to control the normal shock position. The model is flexible and can also be utilized to simulate other mixed compression supersonic inlet designs. The model was validated both in time and in the frequency domain against the legacy LArge Perturbation INlet code, which has been previously verified using test data. This legacy code written in FORTRAN is quite extensive and complex in terms of the amount of software and number of subroutines. Further, the legacy code is not suitable for closed loop feedback controls design, and the simulation environment is not amenable to systems integration. Therefore, a solution is to develop an innovative, more simplified, mixed compression inlet model with the same steady state and dynamic performance as the legacy code that also can be used for controls design. The new nonlinear dynamic model is implemented in MATLAB Simulink. This environment allows easier development of linear models for controls design for shock positioning. The new model is also well suited for integration with a propulsion system model to study inlet/propulsion system performance, and integration with an aero-servo-elastic system model to study integrated vehicle ride quality, vehicle stability, and efficiency.

Kopasakis, George↗
NASA NTRS2017

Review of a Draft - Avoiding the Impossible: Re-focusing a Non-Feasible Mission 2-Hrs into a 3-Day Engineering Session

Concurrent engineering offers a great many benefits to engineers and mission designers throughout the world of aerospace. The only downside of concurrent engineering, and this is somewhat unavoidable, is that you don’t know the results of a design session until the end when it is completed. Usually, this is not a problem – you wouldn’t start building a spacecraft before the design is finished. However, within mass and cost constrained systems, you may end up with a final design that although technically sound – is not feasible due to mass or cost limits. Employing in-session mass and cost models with flexible inputs that refine their estimates and variance as more detailed information comes in throughout a design session allows major design changes to be made when the probability of breaching a mass or cost cap exceeds a threshold level. This enables mission designers to re-focus the study, and avoid spending 3-days with 15 engineers designing a non-feasible mission. By understanding key correlations and nested relationships within mass or cost, and specifically mass or cost allocations per mission element by mission type, it’s possible to get flexible-input, statistically based mass and cost estimates very early in the design process. Baseline models are seeded using mission characteristics and general parameters (outer planetary orbiter-probe mission, $500M cost cap for example) to provide a rough estimate of the expected mass or cost. As information gets solidified during the session, it gets added to the model and the estimates are updated. Continuing the orbiter-probe mission example, modeling probe heat shield cost as a percent of total probe cost, and probe cost as a percent of total flight system cost, and total flight system cost as a percent of total mission cost allows a design team to roll-up solidified information to estimate the probability of fitting within a mass or cost constraint early in a concurrent design session. When only the heat shield cost is known, the variance of the final estimate is higher, whereas when the full probe gets defined, naturally, the variance of the estimate decreases. A methodology, model, verification and demo implementation for cost limit breach are presented.

Hihn, Jairus M.↗