Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Strength scaling in fiber composites

A research program was initiated to study and isolate the factors responsible for scale effects in the tensile strength of graphite/epoxy composite laminates. Four layups were chosen with appropriate stacking sequences so as to highlight individual and interacting failure modes. Four scale sizes were selected for investigation including full scale size, 3/4, 2/4, and 1/4, with n = to 4, 3, 2, and 1, respectively. The full scale specimen sizes was 32 piles thick as compared to 24, 16, and 8 piles for the 3/4, 2/4, and 1/4 specimen sizes respectively. Results were obtained in the form of tensile strength, stress-strain curves and damage development. Problems associated with strength degradation with increasing specimen sizes are isolated and discussed. Inconsistencies associated with strain measurements were also identified. Enchanced X-ray radiography was employed for damage evaluation, following step loading. It was shown that fiber dominated layups were less sensitive to scaling effects compared to the matrix dominated layups.

Kellas, Sotiris↗
DOE OSTI2023

Ply Strength Prediction of Unidirectional Continuous Carbon Fiber Composites

As inhomogeneous orthotropic materials, composite mechanical properties can be difficult to predict. Even with tight fabrication process controls, there is always some microstructural variation that will affect these properties. As a highly defect-dependent phenomena, mechanical strength is even more subject to variation, especially considering that composites exhibit multiple potential failure modes. The most direct way to determine composite material strength is via experimental testing, maintaining loading and specimen morphology as close as possible to the in situ states. When multiple materials and designs are being considered, this process is often prohibitively costly and slow. However, some approximations and rules of thumb can consistently guide the design process and consideration of alternatives.

36 MATERIALS SCIENCE↗
NASA NTRS1968

Tensile failure of fiber composites.

Composite tensile-failure modes, discussing failure load prediction, experimental data and statistical analysis of stress concentration effects

Zweben, C.↗
NASA NTRS1972

On the elastic properties of fiber composite laminates with statistically dispersed ply orientations

Structural application of advanced composite filamentary materials requires lamination of the basic orthotropic plies into angle-ply laminates. The resulting elastic and strength properties depend on the pattern of orientation and are influenced by inevitable errors and inaccuracy in placement of the angle plies. Reviewed is the effect on elastic properties of orientation dispersion. The conventional constitutive relations are recast in a homologous form to account for orientation dispersion by addition of a single parameter. Graphical results are presented to show the behavior of the most important advanced composite materials. The results are directly useful for estimating effects of manufacturing inaccuracy and for design of partially oriented reinforced structures.

Robinson, E. Y.↗
NASA NTRS1973

Evaluation of polyimide/glass fiber composites for construction of light weight pressure vessels for cryogenic propellants

The application of polyimide resin as a matrix for glass filament-wound thin metal-lined pressure vessels was studied over a temperature range of (minus) 320 to 600 F. Keramid 601 polyimide was found to perform quite well over the entire range of temperature. Hoop stress values of 425 ksi were determined at 75 F which is equivalent to epoxy resin in similar structures. At -320 and 600 F, 125 and 80% of this strength was retained. Thermal ageing at 500 F for up to 50 hours was studied with severe reduction in strength, but there is evidence that this reduction could be improved. Another polyimide resin studied was P10PA which was found to have processing characteristics inappropriate for filament-winding. NOL ring tensile and shear data was determined from both resins with S-glass. Pressure vessel design, fabrication and test procedures are described in detail.

Petker, I.↗
NASA NTRS1975

Lamination residual stresses in fiber composites

An experimental investigation was conducted to determine the magnitude of lamination residual stresses in angle-ply composites and to evaluate their effects on composite structural integrity. The materials investigated were boron/epoxy, boron/polyimide, graphite/low modulus epoxy, graphite/high modulus epoxy, graphite/polyimide and s-glass/epoxy. These materials were fully characterized. Static properties of laminates were also determined. Experimental techniques using embedded strain gages were developed and used to measure residual strains during curing. The extent of relaxation of lamination residual stresses was investigated. It was concluded that the degree of such relaxation is low. The behavior of angle-ply laminates subjected to thermal cycling, tensile load cycling, and combined thermal cycling with tensile load was investigated. In most cases these cycling programs did not have any measurable influence on residual strength and stiffness of the laminates. In the tensile load cycling tests, the graphite/polyimide shows the highest endurance with 10 million cycle runouts at loads up to 90 percent of the static strength.

Daniel, I. M.↗
NASA NTRS1976

Ten deg off-axis tensile test for intralaminar shear characterization of fiber composites

A combined theoretical and experimental investigation was conducted to assess the suitability of the 10 deg off-axis tensile test specimen for the intralaminar shear characterization of unidirectional composites. Composite mechanics, a combined-stress failure criterion, and a finite element analysis were used to determine theoretically the stress-strain variation across the specimen width and the relative stress and strain magnitudes at the 10 deg plane. Strain gages were used to measure the strain variation across the specimen width at specimen midlength and near the end tabs. Specimens from Mod-I/epoxy, T-300/epoxy, and S-glass/epoxy were used in the experimental program. It was found that the 10 deg off-axis tensile test specimen is suitable for intralaminar shear characterization and it is recommended that it should be considered as a possible standard test specimen for such a characterization.

Chamis, C. C.↗
NASA NTRS1976

Investigation of thermal fatigue in fiber composite materials

Graphite-epoxy laminates were thermally cycled to determine the effects of thermal cycles on tensile properties and thermal expansion coefficients of the laminates. Three 12-ply laminate configurations were subjected to up to 5,000 thermal cycles. The cumulative effect of the thermal cycles was determined by destructive inspection (electron micrographs and tensile tests) of samples after progressively larger numbers of cycles. After thermal cycling, the materials' tensile strengths, moduli, and thermal expansion coefficients were significantly lower than for the materials as fabricated. Most of the degradation of properties occurred after only a few cycles. The property degradation was attributed primarily to the progressive development of matrix cracks whose locations depended upon the layup orientation of the laminate.

Fahmy, A. A.↗